omap4: Adding hsmmc support to board file
Adding support for MMC1 & MMC2 controllers of OMAP4430 SDP
to board file.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 921cde3..e4a5d66 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -33,6 +33,8 @@
#include <plat/control.h>
#include <plat/timer-gp.h>
#include <plat/usb.h>
+#include <plat/mmc.h>
+#include "hsmmc.h"
#define ETH_KS8851_IRQ 34
#define ETH_KS8851_POWER_ON 48
@@ -137,24 +139,66 @@
.mode = MUSB_PERIPHERAL,
.power = 100,
};
+
+static struct omap2_hsmmc_info mmc[] = {
+ {
+ .mmc = 1,
+ .wires = 8,
+ .gpio_wp = -EINVAL,
+ },
+ {
+ .mmc = 2,
+ .wires = 8,
+ .gpio_cd = -EINVAL,
+ .gpio_wp = -EINVAL,
+ .nonremovable = true,
+ },
+ {} /* Terminator */
+};
+
static struct regulator_consumer_supply sdp4430_vmmc_supply[] = {
{
.supply = "vmmc",
+ .dev_name = "mmci-omap-hs.0",
},
{
.supply = "vmmc",
- },
- {
- .supply = "vmmc",
- },
- {
- .supply = "vmmc",
- },
- {
- .supply = "vmmc",
+ .dev_name = "mmci-omap-hs.1",
},
};
+static int omap4_twl6030_hsmmc_late_init(struct device *dev)
+{
+ int ret = 0;
+ struct platform_device *pdev = container_of(dev,
+ struct platform_device, dev);
+ struct omap_mmc_platform_data *pdata = dev->platform_data;
+
+ /* Setting MMC1 Card detect Irq */
+ if (pdev->id == 0)
+ pdata->slots[0].card_detect_irq = TWL6030_IRQ_BASE +
+ MMCDETECT_INTR_OFFSET;
+ return ret;
+}
+
+static __init void omap4_twl6030_hsmmc_set_late_init(struct device *dev)
+{
+ struct omap_mmc_platform_data *pdata = dev->platform_data;
+
+ pdata->init = omap4_twl6030_hsmmc_late_init;
+}
+
+static int __init omap4_twl6030_hsmmc_init(struct omap2_hsmmc_info *controllers)
+{
+ struct omap2_hsmmc_info *c;
+
+ omap2_hsmmc_init(controllers);
+ for (c = controllers; c->mmc; c++)
+ omap4_twl6030_hsmmc_set_late_init(c->dev);
+
+ return 0;
+}
+
static struct regulator_init_data sdp4430_vaux1 = {
.constraints = {
.min_uV = 1000000,
@@ -206,7 +250,7 @@
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
- .num_consumer_supplies = 5,
+ .num_consumer_supplies = 2,
.consumer_supplies = sdp4430_vmmc_supply,
};
@@ -329,6 +373,7 @@
omap4_i2c_init();
platform_add_devices(sdp4430_devices, ARRAY_SIZE(sdp4430_devices));
omap_serial_init();
+ omap4_twl6030_hsmmc_init(mmc);
/* OMAP4 SDP uses internal transceiver so register nop transceiver */
usb_nop_xceiv_register();
/* FIXME: allow multi-omap to boot until musb is updated for omap4 */