| #include "qcom-apq8064-v2.0.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| model = "Qualcomm APQ8064/IFC6410"; |
| compatible = "qcom,apq8064-ifc6410", "qcom,apq8064"; |
| |
| aliases { |
| serial0 = &gsbi7_serial; |
| serial1 = &gsbi6_serial; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| soc { |
| pinctrl@800000 { |
| card_detect: card_detect { |
| mux { |
| pins = "gpio26"; |
| function = "gpio"; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| rpm@108000 { |
| regulators { |
| vin_lvs1_3_6-supply = <&pm8921_s4>; |
| vin_lvs2-supply = <&pm8921_s1>; |
| vin_lvs4_5_7-supply = <&pm8921_s4>; |
| |
| vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; |
| vdd_l24-supply = <&pm8921_s1>; |
| vdd_l25-supply = <&pm8921_s1>; |
| vdd_l26-supply = <&pm8921_s7>; |
| vdd_l27-supply = <&pm8921_s7>; |
| vdd_l28-supply = <&pm8921_s7>; |
| |
| |
| /* Buck SMPS */ |
| pm8921_s1: s1 { |
| regulator-always-on; |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| qcom,switch-mode-frequency = <3200000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_s3: s3 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1400000>; |
| qcom,switch-mode-frequency = <4800000>; |
| }; |
| |
| pm8921_s4: s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| qcom,switch-mode-frequency = <3200000>; |
| }; |
| |
| pm8921_s7: s7 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| qcom,switch-mode-frequency = <3200000>; |
| }; |
| |
| pm8921_l3: l3 { |
| regulator-min-microvolt = <3050000>; |
| regulator-max-microvolt = <3300000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l4: l4 { |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1800000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l5: l5 { |
| regulator-min-microvolt = <2750000>; |
| regulator-max-microvolt = <3000000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l6: l6 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_l23: l23 { |
| regulator-min-microvolt = <1700000>; |
| regulator-max-microvolt = <1900000>; |
| bias-pull-down; |
| }; |
| |
| pm8921_lvs1: lvs1 { |
| bias-pull-down; |
| }; |
| }; |
| }; |
| |
| ext_3p3v: regulator-fixed@1 { |
| compatible = "regulator-fixed"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "ext_3p3v"; |
| regulator-type = "voltage"; |
| startup-delay-us = <0>; |
| gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| regulator-boot-on; |
| }; |
| |
| gsbi3: gsbi@16200000 { |
| status = "okay"; |
| qcom,mode = <GSBI_PROT_I2C>; |
| i2c3: i2c@16280000 { |
| status = "okay"; |
| }; |
| }; |
| |
| gsbi@12440000 { |
| status = "okay"; |
| qcom,mode = <GSBI_PROT_I2C>; |
| |
| i2c@12460000 { |
| status = "okay"; |
| clock-frequency = <200000>; |
| |
| eeprom@52 { |
| compatible = "atmel,24c128"; |
| reg = <0x52>; |
| pagesize = <32>; |
| }; |
| }; |
| }; |
| |
| gsbi@16500000 { |
| status = "ok"; |
| qcom,mode = <GSBI_PROT_I2C_UART>; |
| |
| serial@16540000 { |
| status = "ok"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gsbi6_uart_4pins>; |
| }; |
| }; |
| |
| gsbi@16600000 { |
| status = "ok"; |
| qcom,mode = <GSBI_PROT_I2C_UART>; |
| serial@16640000 { |
| status = "ok"; |
| }; |
| }; |
| |
| sata_phy0: phy@1b400000 { |
| status = "okay"; |
| }; |
| |
| sata0: sata@29000000 { |
| status = "okay"; |
| target-supply = <&pm8921_s4>; |
| }; |
| |
| /* OTG */ |
| usb1_phy: phy@12500000 { |
| status = "okay"; |
| vddcx-supply = <&pm8921_s3>; |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l4>; |
| }; |
| |
| usb3_phy: phy@12520000 { |
| status = "okay"; |
| vddcx-supply = <&pm8921_s3>; |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l23>; |
| }; |
| |
| usb4_phy: phy@12530000 { |
| status = "okay"; |
| vddcx-supply = <&pm8921_s3>; |
| v3p3-supply = <&pm8921_l3>; |
| v1p8-supply = <&pm8921_l23>; |
| }; |
| |
| gadget1: gadget@12500000 { |
| status = "okay"; |
| }; |
| |
| /* OTG */ |
| usb1: usb@12500000 { |
| status = "okay"; |
| }; |
| |
| usb3: usb@12520000 { |
| status = "okay"; |
| }; |
| |
| usb4: usb@12530000 { |
| status = "okay"; |
| }; |
| |
| amba { |
| /* eMMC */ |
| sdcc1: sdcc@12400000 { |
| status = "okay"; |
| vmmc-supply = <&pm8921_l5>; |
| vqmmc-supply = <&pm8921_s4>; |
| }; |
| |
| /* External micro SD card */ |
| sdcc3: sdcc@12180000 { |
| status = "okay"; |
| vmmc-supply = <&pm8921_l6>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&card_detect>; |
| cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; |
| }; |
| /* WLAN */ |
| sdcc4: sdcc@121c0000 { |
| status = "okay"; |
| vmmc-supply = <&ext_3p3v>; |
| vqmmc-supply = <&pm8921_lvs1>; |
| }; |
| }; |
| }; |
| }; |