e1000: remove leading and trailing whitespace.
Some leading and trailing whitespace made it into the driver code here.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index df819c1..ccbe342 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -349,7 +349,7 @@
* For ASF and Pass Through versions of f/w this means that the
* driver is no longer loaded. For AMT version (only with 82573) i
* of the f/w this means that the netowrk i/f is closed.
- *
+ *
**/
static void
@@ -381,10 +381,10 @@
* @adapter: address of board private structure
*
* e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
- * For ASF and Pass Through versions of f/w this means that
- * the driver is loaded. For AMT version (only with 82573)
+ * For ASF and Pass Through versions of f/w this means that
+ * the driver is loaded. For AMT version (only with 82573)
* of the f/w this means that the netowrk i/f is open.
- *
+ *
**/
static void
@@ -714,8 +714,8 @@
DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
/* if ksp3, indicate if it's port a being setup */
- if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 &&
- e1000_ksp3_port_a == 0)
+ if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 &&
+ e1000_ksp3_port_a == 0)
adapter->ksp3_port_a = 1;
e1000_ksp3_port_a++;
/* Reset for multiple KP3 adapters */
@@ -743,9 +743,9 @@
if (pci_using_dac)
netdev->features |= NETIF_F_HIGHDMA;
- /* hard_start_xmit is safe against parallel locking */
- netdev->features |= NETIF_F_LLTX;
-
+ /* hard_start_xmit is safe against parallel locking */
+ netdev->features |= NETIF_F_LLTX;
+
adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw);
/* before reading the EEPROM, reset the controller to
@@ -2773,7 +2773,7 @@
unsigned int nr_frags = 0;
unsigned int mss = 0;
int count = 0;
- int tso;
+ int tso;
unsigned int f;
len -= skb->data_len;
@@ -2786,7 +2786,7 @@
#ifdef NETIF_F_TSO
mss = skb_shinfo(skb)->tso_size;
- /* The controller does a simple calculation to
+ /* The controller does a simple calculation to
* make sure there is enough room in the FIFO before
* initiating the DMA for each buffer. The calc is:
* 4 = ceil(buffer len/mss). To make sure we don't
@@ -2809,7 +2809,7 @@
case e1000_82573:
pull_size = min((unsigned int)4, skb->data_len);
if (!__pskb_pull_tail(skb, pull_size)) {
- printk(KERN_ERR
+ printk(KERN_ERR
"__pskb_pull_tail failed.\n");
dev_kfree_skb_any(skb);
return NETDEV_TX_OK;
@@ -3755,7 +3755,7 @@
* throughput, so unsplit small packets and save the alloc/put*/
if (l1 && ((length + l1) <= adapter->rx_ps_bsize0)) {
u8 *vaddr;
- /* there is no documentation about how to call
+ /* there is no documentation about how to call
* kmap_atomic, so we can't hold the mapping
* very long */
pci_dma_sync_single_for_cpu(pdev,