[ARM] PCM037 Board: Add I2C support
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
diff --git a/arch/arm/mach-mx3/pcm037.c b/arch/arm/mach-mx3/pcm037.c
index 18cda92..a05e37b 100644
--- a/arch/arm/mach-mx3/pcm037.c
+++ b/arch/arm/mach-mx3/pcm037.c
@@ -26,6 +26,8 @@
#include <linux/gpio.h>
#include <linux/smc911x.h>
#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
@@ -37,6 +39,9 @@
#include <mach/iomux-mx3.h>
#include <mach/board-pcm037.h>
#include <mach/mxc_nand.h>
+#ifdef CONFIG_I2C_IMX
+#include <mach/i2c.h>
+#endif
#include "devices.h"
@@ -117,6 +122,46 @@
.hw_ecc = 1,
};
+#ifdef CONFIG_I2C_IMX
+static int i2c_1_pins[] = {
+ MX31_PIN_CSPI2_MOSI__SCL,
+ MX31_PIN_CSPI2_MISO__SDA,
+};
+
+static int pcm037_i2c_1_init(struct device *dev)
+{
+ return mxc_iomux_setup_multiple_pins(i2c_1_pins, ARRAY_SIZE(i2c_1_pins),
+ "i2c-1");
+}
+
+static void pcm037_i2c_1_exit(struct device *dev)
+{
+ mxc_iomux_release_multiple_pins(i2c_1_pins, ARRAY_SIZE(i2c_1_pins));
+}
+
+static struct imxi2c_platform_data pcm037_i2c_1_data = {
+ .bitrate = 100000,
+ .init = pcm037_i2c_1_init,
+ .exit = pcm037_i2c_1_exit,
+};
+
+static struct at24_platform_data board_eeprom = {
+ .byte_len = 4096,
+ .page_size = 32,
+ .flags = AT24_FLAG_ADDR16,
+};
+
+static struct i2c_board_info pcm037_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */
+ .platform_data = &board_eeprom,
+ }, {
+ I2C_BOARD_INFO("rtc-pcf8563", 0x51),
+ .type = "pcf8563",
+ }
+};
+#endif
+
static struct platform_device *devices[] __initdata = {
&pcm037_flash,
&pcm037_eth,
@@ -156,6 +201,12 @@
"pcm037-eth"))
gpio_direction_input(MX31_PIN_GPIO3_1);
+#ifdef CONFIG_I2C_IMX
+ i2c_register_board_info(1, pcm037_i2c_devices,
+ ARRAY_SIZE(pcm037_i2c_devices));
+
+ mxc_register_device(&mxc_i2c_device1, &pcm037_i2c_1_data);
+#endif
mxc_register_device(&mxc_nand_device, &pcm037_nand_board_info);
}