Merge branches 'pci/host-exynos', 'pci/host-rcar' and 'pci/amd-numa' into next

* pci/host-exynos:
  PCI: exynos: Remove unnecessary OOM messages

* pci/host-rcar:
  PCI: rcar: Add gen2 device tree support
  PCI: rcar: Add R-Car PCIe device tree bindings
  PCI: rcar: Add MSI support for PCIe
  PCI: rcar: Add Renesas R-Car PCIe driver
  PCI: rcar: Use new OF interrupt mapping when possible

* pci/amd-numa:
  x86/PCI: Clean up and mark early_root_info_init() as deprecated
  x86/PCI: Work around AMD Fam15h BIOSes that fail to provide _PXM
  x86/PCI: Warn if we have to "guess" host bridge node information
diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
new file mode 100644
index 0000000..d8ef5bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt
@@ -0,0 +1,66 @@
+Renesas AHB to PCI bridge
+-------------------------
+
+This is the bridge used internally to connect the USB controllers to the
+AHB. There is one bridge instance per USB port connected to the internal
+OHCI and EHCI controllers.
+
+Required properties:
+- compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
+	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+- reg:	A list of physical regions to access the device: the first is
+	the operational registers for the OHCI/EHCI controllers and the
+	second is for the bridge configuration and control registers.
+- interrupts: interrupt for the device.
+- clocks: The reference to the device clock.
+- bus-range: The PCI bus number range; as this is a single bus, the range
+	     should be specified as the same value twice.
+- #address-cells: must be 3.
+- #size-cells: must be 2.
+- #interrupt-cells: must be 1.
+- interrupt-map: standard property used to define the mapping of the PCI
+  interrupts to the GIC interrupts.
+- interrupt-map-mask: standard property that helps to define the interrupt
+  mapping.
+
+Example SoC configuration:
+
+	pci0: pci@ee090000  {
+		compatible = "renesas,pci-r8a7790";
+		clocks = <&mstp7_clks R8A7790_CLK_EHCI>;
+		reg = <0x0 0xee090000 0x0 0xc00>,
+		      <0x0 0xee080000 0x0 0x1100>;
+		interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>;
+		status = "disabled";
+
+		bus-range = <0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0xff00 0 0 0x7>;
+		interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
+				 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH
+				 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>;
+
+		pci@0,1 {
+			reg = <0x800 0 0 0 0>;
+			device_type = "pci";
+			phys = <&usbphy 0 0>;
+			phy-names = "usb";
+		};
+
+		pci@0,2 {
+			reg = <0x1000 0 0 0 0>;
+			device_type = "pci";
+			phys = <&usbphy 0 0>;
+			phy-names = "usb";
+		};
+	};
+
+Example board setup:
+
+&pci0 {
+	status = "okay";
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+};
diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt
new file mode 100644
index 0000000..29d3b98
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt
@@ -0,0 +1,47 @@
+* Renesas RCar PCIe interface
+
+Required properties:
+- compatible: should contain one of the following
+	"renesas,pcie-r8a7779", "renesas,pcie-r8a7790", "renesas,pcie-r8a7791"
+- reg: base address and length of the pcie controller registers.
+- #address-cells: set to <3>
+- #size-cells: set to <2>
+- bus-range: PCI bus numbers covered
+- device_type: set to "pci"
+- ranges: ranges for the PCI memory and I/O regions.
+- dma-ranges: ranges for the inbound memory regions.
+- interrupts: two interrupt sources for MSI interrupts, followed by interrupt
+	source for hardware related interrupts (e.g. link speed change).
+- #interrupt-cells: set to <1>
+- interrupt-map-mask and interrupt-map: standard PCI properties
+	to define the mapping of the PCIe interface to interrupt
+	numbers.
+- clocks: from common clock binding: clock specifiers for the PCIe controller
+	and PCIe bus clocks.
+- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
+
+Example:
+
+SoC specific DT Entry:
+
+	pcie: pcie@fe000000 {
+		compatible = "renesas,pcie-r8a7791";
+		reg = <0 0xfe000000 0 0x80000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x00 0xff>;
+		device_type = "pci";
+		ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000
+			  0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000
+			  0x02000000 0 0x30000000 0 0x30000000 0 0x08000000
+			  0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>;
+		dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000
+			      0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>;
+		interrupts = <0 116 4>, <0 117 4>, <0 118 4>;
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic 0 116 4>;
+		clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>;
+		clock-names = "pcie", "pcie_bus";
+		status = "disabled";
+	};
diff --git a/arch/x86/pci/acpi.c b/arch/x86/pci/acpi.c
index 01edac6..5075371 100644
--- a/arch/x86/pci/acpi.c
+++ b/arch/x86/pci/acpi.c
@@ -489,8 +489,12 @@
 	}
 
 	node = acpi_get_node(device->handle);
-	if (node == NUMA_NO_NODE)
+	if (node == NUMA_NO_NODE) {
 		node = x86_pci_root_bus_node(busnum);
+		if (node != 0 && node != NUMA_NO_NODE)
+			dev_info(&device->dev, FW_BUG "no _PXM; falling back to node %d from hardware (may be inconsistent with ACPI node numbers)\n",
+				node);
+	}
 
 	if (node != NUMA_NO_NODE && !node_online(node))
 		node = NUMA_NO_NODE;
diff --git a/arch/x86/pci/amd_bus.c b/arch/x86/pci/amd_bus.c
index e88f4c5..c20d2cc 100644
--- a/arch/x86/pci/amd_bus.c
+++ b/arch/x86/pci/amd_bus.c
@@ -11,27 +11,33 @@
 
 #include "bus_numa.h"
 
-/*
- * This discovers the pcibus <-> node mapping on AMD K8.
- * also get peer root bus resource for io,mmio
- */
+#define AMD_NB_F0_NODE_ID			0x60
+#define AMD_NB_F0_UNIT_ID			0x64
+#define AMD_NB_F1_CONFIG_MAP_REG		0xe0
 
-struct pci_hostbridge_probe {
+#define RANGE_NUM				16
+#define AMD_NB_F1_CONFIG_MAP_RANGES		4
+
+struct amd_hostbridge {
 	u32 bus;
 	u32 slot;
-	u32 vendor;
 	u32 device;
 };
 
-static struct pci_hostbridge_probe pci_probes[] __initdata = {
-	{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
-	{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
-	{ 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
-	{ 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
+/*
+ * IMPORTANT NOTE:
+ * hb_probes[] and early_root_info_init() is in maintenance mode.
+ * It only supports K8, Fam10h, Fam11h, and Fam15h_00h-0fh .
+ * Future processor will rely on information in ACPI.
+ */
+static struct amd_hostbridge hb_probes[] __initdata = {
+	{ 0, 0x18, 0x1100 }, /* K8 */
+	{ 0, 0x18, 0x1200 }, /* Family10h */
+	{ 0xff, 0, 0x1200 }, /* Family10h */
+	{ 0, 0x18, 0x1300 }, /* Family11h */
+	{ 0, 0x18, 0x1600 }, /* Family15h */
 };
 
-#define RANGE_NUM 16
-
 static struct pci_root_info __init *find_pci_root_info(int node, int link)
 {
 	struct pci_root_info *info;
@@ -45,12 +51,12 @@
 }
 
 /**
- * early_fill_mp_bus_to_node()
+ * early_root_info_init()
  * called before pcibios_scan_root and pci_scan_bus
- * fills the mp_bus_to_cpumask array based according to the LDT Bus Number
- * Registers found in the K8 northbridge
+ * fills the mp_bus_to_cpumask array based according
+ * to the LDT Bus Number Registers found in the northbridge.
  */
-static int __init early_fill_mp_bus_info(void)
+static int __init early_root_info_init(void)
 {
 	int i;
 	unsigned bus;
@@ -75,19 +81,21 @@
 		return -1;
 
 	found = false;
-	for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+	for (i = 0; i < ARRAY_SIZE(hb_probes); i++) {
 		u32 id;
 		u16 device;
 		u16 vendor;
 
-		bus = pci_probes[i].bus;
-		slot = pci_probes[i].slot;
+		bus = hb_probes[i].bus;
+		slot = hb_probes[i].slot;
 		id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
-
 		vendor = id & 0xffff;
 		device = (id>>16) & 0xffff;
-		if (pci_probes[i].vendor == vendor &&
-		    pci_probes[i].device == device) {
+
+		if (vendor != PCI_VENDOR_ID_AMD)
+			continue;
+
+		if (hb_probes[i].device == device) {
 			found = true;
 			break;
 		}
@@ -96,10 +104,16 @@
 	if (!found)
 		return 0;
 
-	for (i = 0; i < 4; i++) {
+	/*
+	 * We should learn topology and routing information from _PXM and
+	 * _CRS methods in the ACPI namespace.  We extract node numbers
+	 * here to work around BIOSes that don't supply _PXM.
+	 */
+	for (i = 0; i < AMD_NB_F1_CONFIG_MAP_RANGES; i++) {
 		int min_bus;
 		int max_bus;
-		reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
+		reg = read_pci_config(bus, slot, 1,
+				AMD_NB_F1_CONFIG_MAP_REG + (i << 2));
 
 		/* Check if that register is enabled for bus range */
 		if ((reg & 7) != 3)
@@ -113,10 +127,21 @@
 		info = alloc_pci_root_info(min_bus, max_bus, node, link);
 	}
 
+	/*
+	 * The following code extracts routing information for use on old
+	 * systems where Linux doesn't automatically use host bridge _CRS
+	 * methods (or when the user specifies "pci=nocrs").
+	 *
+	 * We only do this through Fam11h, because _CRS should be enough on
+	 * newer systems.
+	 */
+	if (boot_cpu_data.x86 > 0x11)
+		return 0;
+
 	/* get the default node and link for left over res */
-	reg = read_pci_config(bus, slot, 0, 0x60);
+	reg = read_pci_config(bus, slot, 0, AMD_NB_F0_NODE_ID);
 	def_node = (reg >> 8) & 0x07;
-	reg = read_pci_config(bus, slot, 0, 0x64);
+	reg = read_pci_config(bus, slot, 0, AMD_NB_F0_UNIT_ID);
 	def_link = (reg >> 8) & 0x03;
 
 	memset(range, 0, sizeof(range));
@@ -363,7 +388,7 @@
 	int cpu;
 
 	/* assume all cpus from fam10h have IO ECS */
-        if (boot_cpu_data.x86 < 0x10)
+	if (boot_cpu_data.x86 < 0x10)
 		return 0;
 
 	/* Try the PCI method first. */
@@ -387,7 +412,7 @@
 	if (boot_cpu_data.x86_vendor != X86_VENDOR_AMD)
 		return 0;
 
-	early_fill_mp_bus_info();
+	early_root_info_init();
 	pci_io_ecs_init();
 
 	return 0;
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index a6f67ec..24d290d 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -33,4 +33,10 @@
 	  There are 3 internal PCI controllers available with a single
 	  built-in EHCI/OHCI host controller present on each one.
 
+config PCI_RCAR_GEN2_PCIE
+	bool "Renesas R-Car PCIe controller"
+	depends on ARCH_SHMOBILE || (ARM && COMPILE_TEST)
+	help
+	  Say Y here if you want PCIe controller support on R-Car Gen2 SoCs.
+
 endmenu
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index 13fb333..19946f9 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -4,3 +4,4 @@
 obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
 obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
 obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
+obj-$(CONFIG_PCI_RCAR_GEN2_PCIE) += pcie-rcar.o
diff --git a/drivers/pci/host/pci-exynos.c b/drivers/pci/host/pci-exynos.c
index 3de6bfb..81aa700 100644
--- a/drivers/pci/host/pci-exynos.c
+++ b/drivers/pci/host/pci-exynos.c
@@ -568,10 +568,8 @@
 
 	exynos_pcie = devm_kzalloc(&pdev->dev, sizeof(*exynos_pcie),
 				GFP_KERNEL);
-	if (!exynos_pcie) {
-		dev_err(&pdev->dev, "no memory for exynos pcie\n");
+	if (!exynos_pcie)
 		return -ENOMEM;
-	}
 
 	pp = &exynos_pcie->pp;
 
diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
index fd3e3ab..3ef854f 100644
--- a/drivers/pci/host/pci-rcar-gen2.c
+++ b/drivers/pci/host/pci-rcar-gen2.c
@@ -15,6 +15,7 @@
 #include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/of_pci.h>
 #include <linux/pci.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
@@ -98,6 +99,7 @@
 	struct resource io_res;
 	struct resource mem_res;
 	struct resource *cfg_res;
+	unsigned busnr;
 	int irq;
 	unsigned long window_size;
 };
@@ -180,8 +182,13 @@
 {
 	struct pci_sys_data *sys = dev->bus->sysdata;
 	struct rcar_pci_priv *priv = sys->private_data;
+	int irq;
 
-	return priv->irq;
+	irq = of_irq_parse_and_map_pci(dev, slot, pin);
+	if (!irq)
+		irq = priv->irq;
+
+	return irq;
 }
 
 #ifdef CONFIG_PCI_DEBUG
@@ -312,8 +319,8 @@
 	pci_add_resource(&sys->resources, &priv->io_res);
 	pci_add_resource(&sys->resources, &priv->mem_res);
 
-	/* Setup bus number based on platform device id */
-	sys->busnr = to_platform_device(priv->dev)->id;
+	/* Setup bus number based on platform device id / of bus-range */
+	sys->busnr = priv->busnr;
 	return 1;
 }
 
@@ -366,6 +373,23 @@
 
 	priv->window_size = SZ_1G;
 
+	if (pdev->dev.of_node) {
+		struct resource busnr;
+		int ret;
+
+		ret = of_pci_parse_bus_range(pdev->dev.of_node, &busnr);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "failed to parse bus-range\n");
+			return ret;
+		}
+
+		priv->busnr = busnr.start;
+		if (busnr.end != busnr.start)
+			dev_warn(&pdev->dev, "only one bus number supported\n");
+	} else {
+		priv->busnr = pdev->id;
+	}
+
 	hw_private[0] = priv;
 	memset(&hw, 0, sizeof(hw));
 	hw.nr_controllers = ARRAY_SIZE(hw_private);
@@ -377,11 +401,20 @@
 	return 0;
 }
 
+static struct of_device_id rcar_pci_of_match[] = {
+	{ .compatible = "renesas,pci-r8a7790", },
+	{ .compatible = "renesas,pci-r8a7791", },
+	{ },
+};
+
+MODULE_DEVICE_TABLE(of, rcar_pci_of_match);
+
 static struct platform_driver rcar_pci_driver = {
 	.driver = {
 		.name = "pci-rcar-gen2",
 		.owner = THIS_MODULE,
 		.suppress_bind_attrs = true,
+		.of_match_table = rcar_pci_of_match,
 	},
 	.probe = rcar_pci_probe,
 };
diff --git a/drivers/pci/host/pcie-rcar.c b/drivers/pci/host/pcie-rcar.c
new file mode 100644
index 0000000..8e06124
--- /dev/null
+++ b/drivers/pci/host/pcie-rcar.c
@@ -0,0 +1,1008 @@
+/*
+ * PCIe driver for Renesas R-Car SoCs
+ *  Copyright (C) 2014 Renesas Electronics Europe Ltd
+ *
+ * Based on:
+ *  arch/sh/drivers/pci/pcie-sh7786.c
+ *  arch/sh/drivers/pci/ops-sh7786.c
+ *  Copyright (C) 2009 - 2011  Paul Mundt
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define DRV_NAME "rcar-pcie"
+
+#define PCIECAR			0x000010
+#define PCIECCTLR		0x000018
+#define  CONFIG_SEND_ENABLE	(1 << 31)
+#define  TYPE0			(0 << 8)
+#define  TYPE1			(1 << 8)
+#define PCIECDR			0x000020
+#define PCIEMSR			0x000028
+#define PCIEINTXR		0x000400
+#define PCIEMSITXR		0x000840
+
+/* Transfer control */
+#define PCIETCTLR		0x02000
+#define  CFINIT			1
+#define PCIETSTR		0x02004
+#define  DATA_LINK_ACTIVE	1
+#define PCIEERRFR		0x02020
+#define  UNSUPPORTED_REQUEST	(1 << 4)
+#define PCIEMSIFR		0x02044
+#define PCIEMSIALR		0x02048
+#define  MSIFE			1
+#define PCIEMSIAUR		0x0204c
+#define PCIEMSIIER		0x02050
+
+/* root port address */
+#define PCIEPRAR(x)		(0x02080 + ((x) * 0x4))
+
+/* local address reg & mask */
+#define PCIELAR(x)		(0x02200 + ((x) * 0x20))
+#define PCIELAMR(x)		(0x02208 + ((x) * 0x20))
+#define  LAM_PREFETCH		(1 << 3)
+#define  LAM_64BIT		(1 << 2)
+#define  LAR_ENABLE		(1 << 1)
+
+/* PCIe address reg & mask */
+#define PCIEPARL(x)		(0x03400 + ((x) * 0x20))
+#define PCIEPARH(x)		(0x03404 + ((x) * 0x20))
+#define PCIEPAMR(x)		(0x03408 + ((x) * 0x20))
+#define PCIEPTCTLR(x)		(0x0340c + ((x) * 0x20))
+#define  PAR_ENABLE		(1 << 31)
+#define  IO_SPACE		(1 << 8)
+
+/* Configuration */
+#define PCICONF(x)		(0x010000 + ((x) * 0x4))
+#define PMCAP(x)		(0x010040 + ((x) * 0x4))
+#define EXPCAP(x)		(0x010070 + ((x) * 0x4))
+#define VCCAP(x)		(0x010100 + ((x) * 0x4))
+
+/* link layer */
+#define IDSETR1			0x011004
+#define TLCTLR			0x011048
+#define MACSR			0x011054
+#define MACCTLR			0x011058
+#define  SCRAMBLE_DISABLE	(1 << 27)
+
+/* R-Car H1 PHY */
+#define H1_PCIEPHYADRR		0x04000c
+#define  WRITE_CMD		(1 << 16)
+#define  PHY_ACK		(1 << 24)
+#define  RATE_POS		12
+#define  LANE_POS		8
+#define  ADR_POS		0
+#define H1_PCIEPHYDOUTR		0x040014
+#define H1_PCIEPHYSR		0x040018
+
+#define INT_PCI_MSI_NR	32
+
+#define RCONF(x)	(PCICONF(0)+(x))
+#define RPMCAP(x)	(PMCAP(0)+(x))
+#define REXPCAP(x)	(EXPCAP(0)+(x))
+#define RVCCAP(x)	(VCCAP(0)+(x))
+
+#define  PCIE_CONF_BUS(b)	(((b) & 0xff) << 24)
+#define  PCIE_CONF_DEV(d)	(((d) & 0x1f) << 19)
+#define  PCIE_CONF_FUNC(f)	(((f) & 0x7) << 16)
+
+#define PCI_MAX_RESOURCES 4
+#define MAX_NR_INBOUND_MAPS 6
+
+struct rcar_msi {
+	DECLARE_BITMAP(used, INT_PCI_MSI_NR);
+	struct irq_domain *domain;
+	struct msi_chip chip;
+	unsigned long pages;
+	struct mutex lock;
+	int irq1;
+	int irq2;
+};
+
+static inline struct rcar_msi *to_rcar_msi(struct msi_chip *chip)
+{
+	return container_of(chip, struct rcar_msi, chip);
+}
+
+/* Structure representing the PCIe interface */
+struct rcar_pcie {
+	struct device		*dev;
+	void __iomem		*base;
+	struct resource		res[PCI_MAX_RESOURCES];
+	struct resource		busn;
+	int			root_bus_nr;
+	struct clk		*clk;
+	struct clk		*bus_clk;
+	struct			rcar_msi msi;
+};
+
+static inline struct rcar_pcie *sys_to_pcie(struct pci_sys_data *sys)
+{
+	return sys->private_data;
+}
+
+static void pci_write_reg(struct rcar_pcie *pcie, unsigned long val,
+			  unsigned long reg)
+{
+	writel(val, pcie->base + reg);
+}
+
+static unsigned long pci_read_reg(struct rcar_pcie *pcie, unsigned long reg)
+{
+	return readl(pcie->base + reg);
+}
+
+enum {
+	PCI_ACCESS_READ,
+	PCI_ACCESS_WRITE,
+};
+
+static void rcar_rmw32(struct rcar_pcie *pcie, int where, u32 mask, u32 data)
+{
+	int shift = 8 * (where & 3);
+	u32 val = pci_read_reg(pcie, where & ~3);
+
+	val &= ~(mask << shift);
+	val |= data << shift;
+	pci_write_reg(pcie, val, where & ~3);
+}
+
+static u32 rcar_read_conf(struct rcar_pcie *pcie, int where)
+{
+	int shift = 8 * (where & 3);
+	u32 val = pci_read_reg(pcie, where & ~3);
+
+	return val >> shift;
+}
+
+/* Serialization is provided by 'pci_lock' in drivers/pci/access.c */
+static int rcar_pcie_config_access(struct rcar_pcie *pcie,
+		unsigned char access_type, struct pci_bus *bus,
+		unsigned int devfn, int where, u32 *data)
+{
+	int dev, func, reg, index;
+
+	dev = PCI_SLOT(devfn);
+	func = PCI_FUNC(devfn);
+	reg = where & ~3;
+	index = reg / 4;
+
+	/*
+	 * While each channel has its own memory-mapped extended config
+	 * space, it's generally only accessible when in endpoint mode.
+	 * When in root complex mode, the controller is unable to target
+	 * itself with either type 0 or type 1 accesses, and indeed, any
+	 * controller initiated target transfer to its own config space
+	 * result in a completer abort.
+	 *
+	 * Each channel effectively only supports a single device, but as
+	 * the same channel <-> device access works for any PCI_SLOT()
+	 * value, we cheat a bit here and bind the controller's config
+	 * space to devfn 0 in order to enable self-enumeration. In this
+	 * case the regular ECAR/ECDR path is sidelined and the mangled
+	 * config access itself is initiated as an internal bus transaction.
+	 */
+	if (pci_is_root_bus(bus)) {
+		if (dev != 0)
+			return PCIBIOS_DEVICE_NOT_FOUND;
+
+		if (access_type == PCI_ACCESS_READ) {
+			*data = pci_read_reg(pcie, PCICONF(index));
+		} else {
+			/* Keep an eye out for changes to the root bus number */
+			if (pci_is_root_bus(bus) && (reg == PCI_PRIMARY_BUS))
+				pcie->root_bus_nr = *data & 0xff;
+
+			pci_write_reg(pcie, *data, PCICONF(index));
+		}
+
+		return PCIBIOS_SUCCESSFUL;
+	}
+
+	if (pcie->root_bus_nr < 0)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/* Clear errors */
+	pci_write_reg(pcie, pci_read_reg(pcie, PCIEERRFR), PCIEERRFR);
+
+	/* Set the PIO address */
+	pci_write_reg(pcie, PCIE_CONF_BUS(bus->number) | PCIE_CONF_DEV(dev) |
+				PCIE_CONF_FUNC(func) | reg, PCIECAR);
+
+	/* Enable the configuration access */
+	if (bus->parent->number == pcie->root_bus_nr)
+		pci_write_reg(pcie, CONFIG_SEND_ENABLE | TYPE0, PCIECCTLR);
+	else
+		pci_write_reg(pcie, CONFIG_SEND_ENABLE | TYPE1, PCIECCTLR);
+
+	/* Check for errors */
+	if (pci_read_reg(pcie, PCIEERRFR) & UNSUPPORTED_REQUEST)
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	/* Check for master and target aborts */
+	if (rcar_read_conf(pcie, RCONF(PCI_STATUS)) &
+		(PCI_STATUS_REC_MASTER_ABORT | PCI_STATUS_REC_TARGET_ABORT))
+		return PCIBIOS_DEVICE_NOT_FOUND;
+
+	if (access_type == PCI_ACCESS_READ)
+		*data = pci_read_reg(pcie, PCIECDR);
+	else
+		pci_write_reg(pcie, *data, PCIECDR);
+
+	/* Disable the configuration access */
+	pci_write_reg(pcie, 0, PCIECCTLR);
+
+	return PCIBIOS_SUCCESSFUL;
+}
+
+static int rcar_pcie_read_conf(struct pci_bus *bus, unsigned int devfn,
+			       int where, int size, u32 *val)
+{
+	struct rcar_pcie *pcie = sys_to_pcie(bus->sysdata);
+	int ret;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	ret = rcar_pcie_config_access(pcie, PCI_ACCESS_READ,
+				      bus, devfn, where, val);
+	if (ret != PCIBIOS_SUCCESSFUL) {
+		*val = 0xffffffff;
+		return ret;
+	}
+
+	if (size == 1)
+		*val = (*val >> (8 * (where & 3))) & 0xff;
+	else if (size == 2)
+		*val = (*val >> (8 * (where & 2))) & 0xffff;
+
+	dev_dbg(&bus->dev, "pcie-config-read: bus=%3d devfn=0x%04x "
+		"where=0x%04x size=%d val=0x%08lx\n", bus->number,
+		devfn, where, size, (unsigned long)*val);
+
+	return ret;
+}
+
+/* Serialization is provided by 'pci_lock' in drivers/pci/access.c */
+static int rcar_pcie_write_conf(struct pci_bus *bus, unsigned int devfn,
+				int where, int size, u32 val)
+{
+	struct rcar_pcie *pcie = sys_to_pcie(bus->sysdata);
+	int shift, ret;
+	u32 data;
+
+	if ((size == 2) && (where & 1))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+	else if ((size == 4) && (where & 3))
+		return PCIBIOS_BAD_REGISTER_NUMBER;
+
+	ret = rcar_pcie_config_access(pcie, PCI_ACCESS_READ,
+				      bus, devfn, where, &data);
+	if (ret != PCIBIOS_SUCCESSFUL)
+		return ret;
+
+	dev_dbg(&bus->dev, "pcie-config-write: bus=%3d devfn=0x%04x "
+		"where=0x%04x size=%d val=0x%08lx\n", bus->number,
+		devfn, where, size, (unsigned long)val);
+
+	if (size == 1) {
+		shift = 8 * (where & 3);
+		data &= ~(0xff << shift);
+		data |= ((val & 0xff) << shift);
+	} else if (size == 2) {
+		shift = 8 * (where & 2);
+		data &= ~(0xffff << shift);
+		data |= ((val & 0xffff) << shift);
+	} else
+		data = val;
+
+	ret = rcar_pcie_config_access(pcie, PCI_ACCESS_WRITE,
+				      bus, devfn, where, &data);
+
+	return ret;
+}
+
+static struct pci_ops rcar_pcie_ops = {
+	.read	= rcar_pcie_read_conf,
+	.write	= rcar_pcie_write_conf,
+};
+
+static void rcar_pcie_setup_window(int win, struct resource *res,
+				   struct rcar_pcie *pcie)
+{
+	/* Setup PCIe address space mappings for each resource */
+	resource_size_t size;
+	u32 mask;
+
+	pci_write_reg(pcie, 0x00000000, PCIEPTCTLR(win));
+
+	/*
+	 * The PAMR mask is calculated in units of 128Bytes, which
+	 * keeps things pretty simple.
+	 */
+	size = resource_size(res);
+	mask = (roundup_pow_of_two(size) / SZ_128) - 1;
+	pci_write_reg(pcie, mask << 7, PCIEPAMR(win));
+
+	pci_write_reg(pcie, upper_32_bits(res->start), PCIEPARH(win));
+	pci_write_reg(pcie, lower_32_bits(res->start), PCIEPARL(win));
+
+	/* First resource is for IO */
+	mask = PAR_ENABLE;
+	if (res->flags & IORESOURCE_IO)
+		mask |= IO_SPACE;
+
+	pci_write_reg(pcie, mask, PCIEPTCTLR(win));
+}
+
+static int rcar_pcie_setup(int nr, struct pci_sys_data *sys)
+{
+	struct rcar_pcie *pcie = sys_to_pcie(sys);
+	struct resource *res;
+	int i;
+
+	pcie->root_bus_nr = -1;
+
+	/* Setup PCI resources */
+	for (i = 0; i < PCI_MAX_RESOURCES; i++) {
+
+		res = &pcie->res[i];
+		if (!res->flags)
+			continue;
+
+		rcar_pcie_setup_window(i, res, pcie);
+
+		if (res->flags & IORESOURCE_IO)
+			pci_ioremap_io(nr * SZ_64K, res->start);
+		else
+			pci_add_resource(&sys->resources, res);
+	}
+	pci_add_resource(&sys->resources, &pcie->busn);
+
+	return 1;
+}
+
+static void rcar_pcie_add_bus(struct pci_bus *bus)
+{
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		struct rcar_pcie *pcie = sys_to_pcie(bus->sysdata);
+
+		bus->msi = &pcie->msi.chip;
+	}
+}
+
+struct hw_pci rcar_pci = {
+	.setup          = rcar_pcie_setup,
+	.map_irq        = of_irq_parse_and_map_pci,
+	.ops            = &rcar_pcie_ops,
+	.add_bus        = rcar_pcie_add_bus,
+};
+
+static void rcar_pcie_enable(struct rcar_pcie *pcie)
+{
+	struct platform_device *pdev = to_platform_device(pcie->dev);
+
+	rcar_pci.nr_controllers = 1;
+	rcar_pci.private_data = (void **)&pcie;
+
+	pci_common_init_dev(&pdev->dev, &rcar_pci);
+#ifdef CONFIG_PCI_DOMAINS
+	rcar_pci.domain++;
+#endif
+}
+
+static int phy_wait_for_ack(struct rcar_pcie *pcie)
+{
+	unsigned int timeout = 100;
+
+	while (timeout--) {
+		if (pci_read_reg(pcie, H1_PCIEPHYADRR) & PHY_ACK)
+			return 0;
+
+		udelay(100);
+	}
+
+	dev_err(pcie->dev, "Access to PCIe phy timed out\n");
+
+	return -ETIMEDOUT;
+}
+
+static void phy_write_reg(struct rcar_pcie *pcie,
+				 unsigned int rate, unsigned int addr,
+				 unsigned int lane, unsigned int data)
+{
+	unsigned long phyaddr;
+
+	phyaddr = WRITE_CMD |
+		((rate & 1) << RATE_POS) |
+		((lane & 0xf) << LANE_POS) |
+		((addr & 0xff) << ADR_POS);
+
+	/* Set write data */
+	pci_write_reg(pcie, data, H1_PCIEPHYDOUTR);
+	pci_write_reg(pcie, phyaddr, H1_PCIEPHYADRR);
+
+	/* Ignore errors as they will be dealt with if the data link is down */
+	phy_wait_for_ack(pcie);
+
+	/* Clear command */
+	pci_write_reg(pcie, 0, H1_PCIEPHYDOUTR);
+	pci_write_reg(pcie, 0, H1_PCIEPHYADRR);
+
+	/* Ignore errors as they will be dealt with if the data link is down */
+	phy_wait_for_ack(pcie);
+}
+
+static int rcar_pcie_wait_for_dl(struct rcar_pcie *pcie)
+{
+	unsigned int timeout = 10;
+
+	while (timeout--) {
+		if ((pci_read_reg(pcie, PCIETSTR) & DATA_LINK_ACTIVE))
+			return 0;
+
+		msleep(5);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int rcar_pcie_hw_init(struct rcar_pcie *pcie)
+{
+	int err;
+
+	/* Begin initialization */
+	pci_write_reg(pcie, 0, PCIETCTLR);
+
+	/* Set mode */
+	pci_write_reg(pcie, 1, PCIEMSR);
+
+	/*
+	 * Initial header for port config space is type 1, set the device
+	 * class to match. Hardware takes care of propagating the IDSETR
+	 * settings, so there is no need to bother with a quirk.
+	 */
+	pci_write_reg(pcie, PCI_CLASS_BRIDGE_PCI << 16, IDSETR1);
+
+	/*
+	 * Setup Secondary Bus Number & Subordinate Bus Number, even though
+	 * they aren't used, to avoid bridge being detected as broken.
+	 */
+	rcar_rmw32(pcie, RCONF(PCI_SECONDARY_BUS), 0xff, 1);
+	rcar_rmw32(pcie, RCONF(PCI_SUBORDINATE_BUS), 0xff, 1);
+
+	/* Initialize default capabilities. */
+	rcar_rmw32(pcie, REXPCAP(0), 0, PCI_CAP_ID_EXP);
+	rcar_rmw32(pcie, REXPCAP(PCI_EXP_FLAGS),
+		PCI_EXP_FLAGS_TYPE, PCI_EXP_TYPE_ROOT_PORT << 4);
+	rcar_rmw32(pcie, RCONF(PCI_HEADER_TYPE), 0x7f,
+		PCI_HEADER_TYPE_BRIDGE);
+
+	/* Enable data link layer active state reporting */
+	rcar_rmw32(pcie, REXPCAP(PCI_EXP_LNKCAP), 0, PCI_EXP_LNKCAP_DLLLARC);
+
+	/* Write out the physical slot number = 0 */
+	rcar_rmw32(pcie, REXPCAP(PCI_EXP_SLTCAP), PCI_EXP_SLTCAP_PSN, 0);
+
+	/* Set the completion timer timeout to the maximum 50ms. */
+	rcar_rmw32(pcie, TLCTLR+1, 0x3f, 50);
+
+	/* Terminate list of capabilities (Next Capability Offset=0) */
+	rcar_rmw32(pcie, RVCCAP(0), 0xfff0, 0);
+
+	/* Enable MAC data scrambling. */
+	rcar_rmw32(pcie, MACCTLR, SCRAMBLE_DISABLE, 0);
+
+	/* Enable MSI */
+	if (IS_ENABLED(CONFIG_PCI_MSI))
+		pci_write_reg(pcie, 0x101f0000, PCIEMSITXR);
+
+	/* Finish initialization - establish a PCI Express link */
+	pci_write_reg(pcie, CFINIT, PCIETCTLR);
+
+	/* This will timeout if we don't have a link. */
+	err = rcar_pcie_wait_for_dl(pcie);
+	if (err)
+		return err;
+
+	/* Enable INTx interrupts */
+	rcar_rmw32(pcie, PCIEINTXR, 0, 0xF << 8);
+
+	/* Enable slave Bus Mastering */
+	rcar_rmw32(pcie, RCONF(PCI_STATUS), PCI_STATUS_DEVSEL_MASK,
+		PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
+		PCI_STATUS_CAP_LIST | PCI_STATUS_DEVSEL_FAST);
+
+	wmb();
+
+	return 0;
+}
+
+static int rcar_pcie_hw_init_h1(struct rcar_pcie *pcie)
+{
+	unsigned int timeout = 10;
+
+	/* Initialize the phy */
+	phy_write_reg(pcie, 0, 0x42, 0x1, 0x0EC34191);
+	phy_write_reg(pcie, 1, 0x42, 0x1, 0x0EC34180);
+	phy_write_reg(pcie, 0, 0x43, 0x1, 0x00210188);
+	phy_write_reg(pcie, 1, 0x43, 0x1, 0x00210188);
+	phy_write_reg(pcie, 0, 0x44, 0x1, 0x015C0014);
+	phy_write_reg(pcie, 1, 0x44, 0x1, 0x015C0014);
+	phy_write_reg(pcie, 1, 0x4C, 0x1, 0x786174A0);
+	phy_write_reg(pcie, 1, 0x4D, 0x1, 0x048000BB);
+	phy_write_reg(pcie, 0, 0x51, 0x1, 0x079EC062);
+	phy_write_reg(pcie, 0, 0x52, 0x1, 0x20000000);
+	phy_write_reg(pcie, 1, 0x52, 0x1, 0x20000000);
+	phy_write_reg(pcie, 1, 0x56, 0x1, 0x00003806);
+
+	phy_write_reg(pcie, 0, 0x60, 0x1, 0x004B03A5);
+	phy_write_reg(pcie, 0, 0x64, 0x1, 0x3F0F1F0F);
+	phy_write_reg(pcie, 0, 0x66, 0x1, 0x00008000);
+
+	while (timeout--) {
+		if (pci_read_reg(pcie, H1_PCIEPHYSR))
+			return rcar_pcie_hw_init(pcie);
+
+		msleep(5);
+	}
+
+	return -ETIMEDOUT;
+}
+
+static int rcar_msi_alloc(struct rcar_msi *chip)
+{
+	int msi;
+
+	mutex_lock(&chip->lock);
+
+	msi = find_first_zero_bit(chip->used, INT_PCI_MSI_NR);
+	if (msi < INT_PCI_MSI_NR)
+		set_bit(msi, chip->used);
+	else
+		msi = -ENOSPC;
+
+	mutex_unlock(&chip->lock);
+
+	return msi;
+}
+
+static void rcar_msi_free(struct rcar_msi *chip, unsigned long irq)
+{
+	mutex_lock(&chip->lock);
+	clear_bit(irq, chip->used);
+	mutex_unlock(&chip->lock);
+}
+
+static irqreturn_t rcar_pcie_msi_irq(int irq, void *data)
+{
+	struct rcar_pcie *pcie = data;
+	struct rcar_msi *msi = &pcie->msi;
+	unsigned long reg;
+
+	reg = pci_read_reg(pcie, PCIEMSIFR);
+
+	/* MSI & INTx share an interrupt - we only handle MSI here */
+	if (!reg)
+		return IRQ_NONE;
+
+	while (reg) {
+		unsigned int index = find_first_bit(&reg, 32);
+		unsigned int irq;
+
+		/* clear the interrupt */
+		pci_write_reg(pcie, 1 << index, PCIEMSIFR);
+
+		irq = irq_find_mapping(msi->domain, index);
+		if (irq) {
+			if (test_bit(index, msi->used))
+				generic_handle_irq(irq);
+			else
+				dev_info(pcie->dev, "unhandled MSI\n");
+		} else {
+			/* Unknown MSI, just clear it */
+			dev_dbg(pcie->dev, "unexpected MSI\n");
+		}
+
+		/* see if there's any more pending in this vector */
+		reg = pci_read_reg(pcie, PCIEMSIFR);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int rcar_msi_setup_irq(struct msi_chip *chip, struct pci_dev *pdev,
+			      struct msi_desc *desc)
+{
+	struct rcar_msi *msi = to_rcar_msi(chip);
+	struct rcar_pcie *pcie = container_of(chip, struct rcar_pcie, msi.chip);
+	struct msi_msg msg;
+	unsigned int irq;
+	int hwirq;
+
+	hwirq = rcar_msi_alloc(msi);
+	if (hwirq < 0)
+		return hwirq;
+
+	irq = irq_create_mapping(msi->domain, hwirq);
+	if (!irq) {
+		rcar_msi_free(msi, hwirq);
+		return -EINVAL;
+	}
+
+	irq_set_msi_desc(irq, desc);
+
+	msg.address_lo = pci_read_reg(pcie, PCIEMSIALR) & ~MSIFE;
+	msg.address_hi = pci_read_reg(pcie, PCIEMSIAUR);
+	msg.data = hwirq;
+
+	write_msi_msg(irq, &msg);
+
+	return 0;
+}
+
+static void rcar_msi_teardown_irq(struct msi_chip *chip, unsigned int irq)
+{
+	struct rcar_msi *msi = to_rcar_msi(chip);
+	struct irq_data *d = irq_get_irq_data(irq);
+
+	rcar_msi_free(msi, d->hwirq);
+}
+
+static struct irq_chip rcar_msi_irq_chip = {
+	.name = "R-Car PCIe MSI",
+	.irq_enable = unmask_msi_irq,
+	.irq_disable = mask_msi_irq,
+	.irq_mask = mask_msi_irq,
+	.irq_unmask = unmask_msi_irq,
+};
+
+static int rcar_msi_map(struct irq_domain *domain, unsigned int irq,
+			irq_hw_number_t hwirq)
+{
+	irq_set_chip_and_handler(irq, &rcar_msi_irq_chip, handle_simple_irq);
+	irq_set_chip_data(irq, domain->host_data);
+	set_irq_flags(irq, IRQF_VALID);
+
+	return 0;
+}
+
+static const struct irq_domain_ops msi_domain_ops = {
+	.map = rcar_msi_map,
+};
+
+static int rcar_pcie_enable_msi(struct rcar_pcie *pcie)
+{
+	struct platform_device *pdev = to_platform_device(pcie->dev);
+	struct rcar_msi *msi = &pcie->msi;
+	unsigned long base;
+	int err;
+
+	mutex_init(&msi->lock);
+
+	msi->chip.dev = pcie->dev;
+	msi->chip.setup_irq = rcar_msi_setup_irq;
+	msi->chip.teardown_irq = rcar_msi_teardown_irq;
+
+	msi->domain = irq_domain_add_linear(pcie->dev->of_node, INT_PCI_MSI_NR,
+					    &msi_domain_ops, &msi->chip);
+	if (!msi->domain) {
+		dev_err(&pdev->dev, "failed to create IRQ domain\n");
+		return -ENOMEM;
+	}
+
+	/* Two irqs are for MSI, but they are also used for non-MSI irqs */
+	err = devm_request_irq(&pdev->dev, msi->irq1, rcar_pcie_msi_irq,
+			       IRQF_SHARED, rcar_msi_irq_chip.name, pcie);
+	if (err < 0) {
+		dev_err(&pdev->dev, "failed to request IRQ: %d\n", err);
+		goto err;
+	}
+
+	err = devm_request_irq(&pdev->dev, msi->irq2, rcar_pcie_msi_irq,
+			       IRQF_SHARED, rcar_msi_irq_chip.name, pcie);
+	if (err < 0) {
+		dev_err(&pdev->dev, "failed to request IRQ: %d\n", err);
+		goto err;
+	}
+
+	/* setup MSI data target */
+	msi->pages = __get_free_pages(GFP_KERNEL, 0);
+	base = virt_to_phys((void *)msi->pages);
+
+	pci_write_reg(pcie, base | MSIFE, PCIEMSIALR);
+	pci_write_reg(pcie, 0, PCIEMSIAUR);
+
+	/* enable all MSI interrupts */
+	pci_write_reg(pcie, 0xffffffff, PCIEMSIIER);
+
+	return 0;
+
+err:
+	irq_domain_remove(msi->domain);
+	return err;
+}
+
+static int rcar_pcie_get_resources(struct platform_device *pdev,
+				   struct rcar_pcie *pcie)
+{
+	struct resource res;
+	int err, i;
+
+	err = of_address_to_resource(pdev->dev.of_node, 0, &res);
+	if (err)
+		return err;
+
+	pcie->clk = devm_clk_get(&pdev->dev, "pcie");
+	if (IS_ERR(pcie->clk)) {
+		dev_err(pcie->dev, "cannot get platform clock\n");
+		return PTR_ERR(pcie->clk);
+	}
+	err = clk_prepare_enable(pcie->clk);
+	if (err)
+		goto fail_clk;
+
+	pcie->bus_clk = devm_clk_get(&pdev->dev, "pcie_bus");
+	if (IS_ERR(pcie->bus_clk)) {
+		dev_err(pcie->dev, "cannot get pcie bus clock\n");
+		err = PTR_ERR(pcie->bus_clk);
+		goto fail_clk;
+	}
+	err = clk_prepare_enable(pcie->bus_clk);
+	if (err)
+		goto err_map_reg;
+
+	i = irq_of_parse_and_map(pdev->dev.of_node, 0);
+	if (i < 0) {
+		dev_err(pcie->dev, "cannot get platform resources for msi interrupt\n");
+		err = -ENOENT;
+		goto err_map_reg;
+	}
+	pcie->msi.irq1 = i;
+
+	i = irq_of_parse_and_map(pdev->dev.of_node, 1);
+	if (i < 0) {
+		dev_err(pcie->dev, "cannot get platform resources for msi interrupt\n");
+		err = -ENOENT;
+		goto err_map_reg;
+	}
+	pcie->msi.irq2 = i;
+
+	pcie->base = devm_ioremap_resource(&pdev->dev, &res);
+	if (IS_ERR(pcie->base)) {
+		err = PTR_ERR(pcie->base);
+		goto err_map_reg;
+	}
+
+	return 0;
+
+err_map_reg:
+	clk_disable_unprepare(pcie->bus_clk);
+fail_clk:
+	clk_disable_unprepare(pcie->clk);
+
+	return err;
+}
+
+static int rcar_pcie_inbound_ranges(struct rcar_pcie *pcie,
+				    struct of_pci_range *range,
+				    int *index)
+{
+	u64 restype = range->flags;
+	u64 cpu_addr = range->cpu_addr;
+	u64 cpu_end = range->cpu_addr + range->size;
+	u64 pci_addr = range->pci_addr;
+	u32 flags = LAM_64BIT | LAR_ENABLE;
+	u64 mask;
+	u64 size;
+	int idx = *index;
+
+	if (restype & IORESOURCE_PREFETCH)
+		flags |= LAM_PREFETCH;
+
+	/*
+	 * If the size of the range is larger than the alignment of the start
+	 * address, we have to use multiple entries to perform the mapping.
+	 */
+	if (cpu_addr > 0) {
+		unsigned long nr_zeros = __ffs64(cpu_addr);
+		u64 alignment = 1ULL << nr_zeros;
+		size = min(range->size, alignment);
+	} else {
+		size = range->size;
+	}
+	/* Hardware supports max 4GiB inbound region */
+	size = min(size, 1ULL << 32);
+
+	mask = roundup_pow_of_two(size) - 1;
+	mask &= ~0xf;
+
+	while (cpu_addr < cpu_end) {
+		/*
+		 * Set up 64-bit inbound regions as the range parser doesn't
+		 * distinguish between 32 and 64-bit types.
+		 */
+		pci_write_reg(pcie, lower_32_bits(pci_addr), PCIEPRAR(idx));
+		pci_write_reg(pcie, lower_32_bits(cpu_addr), PCIELAR(idx));
+		pci_write_reg(pcie, lower_32_bits(mask) | flags, PCIELAMR(idx));
+
+		pci_write_reg(pcie, upper_32_bits(pci_addr), PCIEPRAR(idx+1));
+		pci_write_reg(pcie, upper_32_bits(cpu_addr), PCIELAR(idx+1));
+		pci_write_reg(pcie, 0, PCIELAMR(idx+1));
+
+		pci_addr += size;
+		cpu_addr += size;
+		idx += 2;
+
+		if (idx > MAX_NR_INBOUND_MAPS) {
+			dev_err(pcie->dev, "Failed to map inbound regions!\n");
+			return -EINVAL;
+		}
+	}
+	*index = idx;
+
+	return 0;
+}
+
+static int pci_dma_range_parser_init(struct of_pci_range_parser *parser,
+				     struct device_node *node)
+{
+	const int na = 3, ns = 2;
+	int rlen;
+
+	parser->node = node;
+	parser->pna = of_n_addr_cells(node);
+	parser->np = parser->pna + na + ns;
+
+	parser->range = of_get_property(node, "dma-ranges", &rlen);
+	if (!parser->range)
+		return -ENOENT;
+
+	parser->end = parser->range + rlen / sizeof(__be32);
+	return 0;
+}
+
+static int rcar_pcie_parse_map_dma_ranges(struct rcar_pcie *pcie,
+					  struct device_node *np)
+{
+	struct of_pci_range range;
+	struct of_pci_range_parser parser;
+	int index = 0;
+	int err;
+
+	if (pci_dma_range_parser_init(&parser, np))
+		return -EINVAL;
+
+	/* Get the dma-ranges from DT */
+	for_each_of_pci_range(&parser, &range) {
+		u64 end = range.cpu_addr + range.size - 1;
+		dev_dbg(pcie->dev, "0x%08x 0x%016llx..0x%016llx -> 0x%016llx\n",
+			range.flags, range.cpu_addr, end, range.pci_addr);
+
+		err = rcar_pcie_inbound_ranges(pcie, &range, &index);
+		if (err)
+			return err;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id rcar_pcie_of_match[] = {
+	{ .compatible = "renesas,pcie-r8a7779", .data = rcar_pcie_hw_init_h1 },
+	{ .compatible = "renesas,pcie-r8a7790", .data = rcar_pcie_hw_init },
+	{ .compatible = "renesas,pcie-r8a7791", .data = rcar_pcie_hw_init },
+	{},
+};
+MODULE_DEVICE_TABLE(of, rcar_pcie_of_match);
+
+static int rcar_pcie_probe(struct platform_device *pdev)
+{
+	struct rcar_pcie *pcie;
+	unsigned int data;
+	struct of_pci_range range;
+	struct of_pci_range_parser parser;
+	const struct of_device_id *of_id;
+	int err, win = 0;
+	int (*hw_init_fn)(struct rcar_pcie *);
+
+	pcie = devm_kzalloc(&pdev->dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	pcie->dev = &pdev->dev;
+	platform_set_drvdata(pdev, pcie);
+
+	/* Get the bus range */
+	if (of_pci_parse_bus_range(pdev->dev.of_node, &pcie->busn)) {
+		dev_err(&pdev->dev, "failed to parse bus-range property\n");
+		return -EINVAL;
+	}
+
+	if (of_pci_range_parser_init(&parser, pdev->dev.of_node)) {
+		dev_err(&pdev->dev, "missing ranges property\n");
+		return -EINVAL;
+	}
+
+	err = rcar_pcie_get_resources(pdev, pcie);
+	if (err < 0) {
+		dev_err(&pdev->dev, "failed to request resources: %d\n", err);
+		return err;
+	}
+
+	for_each_of_pci_range(&parser, &range) {
+		of_pci_range_to_resource(&range, pdev->dev.of_node,
+						&pcie->res[win++]);
+
+		if (win > PCI_MAX_RESOURCES)
+			break;
+	}
+
+	 err = rcar_pcie_parse_map_dma_ranges(pcie, pdev->dev.of_node);
+	 if (err)
+		return err;
+
+	if (IS_ENABLED(CONFIG_PCI_MSI)) {
+		err = rcar_pcie_enable_msi(pcie);
+		if (err < 0) {
+			dev_err(&pdev->dev,
+				"failed to enable MSI support: %d\n",
+				err);
+			return err;
+		}
+	}
+
+	of_id = of_match_device(rcar_pcie_of_match, pcie->dev);
+	if (!of_id || !of_id->data)
+		return -EINVAL;
+	hw_init_fn = of_id->data;
+
+	/* Failure to get a link might just be that no cards are inserted */
+	err = hw_init_fn(pcie);
+	if (err) {
+		dev_info(&pdev->dev, "PCIe link down\n");
+		return 0;
+	}
+
+	data = pci_read_reg(pcie, MACSR);
+	dev_info(&pdev->dev, "PCIe x%d: link up\n", (data >> 20) & 0x3f);
+
+	rcar_pcie_enable(pcie);
+
+	return 0;
+}
+
+static struct platform_driver rcar_pcie_driver = {
+	.driver = {
+		.name = DRV_NAME,
+		.owner = THIS_MODULE,
+		.of_match_table = rcar_pcie_of_match,
+		.suppress_bind_attrs = true,
+	},
+	.probe = rcar_pcie_probe,
+};
+module_platform_driver(rcar_pcie_driver);
+
+MODULE_AUTHOR("Phil Edworthy <phil.edworthy@renesas.com>");
+MODULE_DESCRIPTION("Renesas R-Car PCIe driver");
+MODULE_LICENSE("GPLv2");