drivers/media/video/bt832.c - kernel/msm-4.9 - Gitiles

 /* Driver for Bt832 CMOS Camera Video Processor
     i2c-addresses: 0x88 or 0x8a

   The BT832 interfaces to a Quartzsight Digital Camera (352x288, 25 or 30 fps)
   via a 9 pin connector ( 4-wire SDATA, 2-wire i2c, SCLK, VCC, GND).
   It outputs an 8-bit 4:2:2 YUV or YCrCb video signal which can be directly
   connected to bt848/bt878 GPIO pins on this purpose.
   (see: VLSI Vision Ltd. www.vvl.co.uk for camera datasheets)

   Supported Cards:
   -  Pixelview Rev.4E: 0x8a
 		GPIO 0x400000 toggles Bt832 RESET, and the chip changes to i2c 0x88 !

   (c) Gunther Mayer, 2002

   STATUS:
   - detect chip and hexdump
   - reset chip and leave low power mode
   - detect camera present

   TODO:
   - make it work (find correct setup for Bt832 and Bt878)
 */

 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/i2c.h>
 #include <linux/types.h>
 #include <linux/videodev.h>
 #include <linux/init.h>
 #include <linux/errno.h>
 #include <linux/slab.h>

 #include <media/audiochip.h>
 #include "bttv.h"
 #include "bt832.h"

 MODULE_LICENSE("GPL");

 /* Addresses to scan */
 static unsigned short normal_i2c[] = { I2C_BT832_ALT1>>1, I2C_BT832_ALT2>>1,
 				       I2C_CLIENT_END };
 I2C_CLIENT_INSMOD;

 /* ---------------------------------------------------------------------- */

 #define dprintk     if (debug) printk

 static int bt832_detach(struct i2c_client *client);


 static struct i2c_driver driver;
 static struct i2c_client client_template;

 struct bt832 {
 	struct i2c_client client;
 };

 int bt832_hexdump(struct i2c_client *i2c_client_s, unsigned char *buf)
 {
 	int i,rc;
 	buf[0]=0x80; // start at register 0 with auto-increment
 	if (1 != (rc = i2c_master_send(i2c_client_s,buf,1)))
 		printk("bt832: i2c i/o error: rc == %d (should be 1)\n",rc);

 	for(i=0;i<65;i++)
 		buf[i]=0;
 	if (65 != (rc=i2c_master_recv(i2c_client_s,buf,65)))
 		printk("bt832: i2c i/o error: rc == %d (should be 65)\n",rc);

 	// Note: On READ the first byte is the current index
 	//  (e.g. 0x80, what we just wrote)

 	if(1) {
 		int i;
 		printk("BT832 hexdump:\n");
 		for(i=1;i<65;i++) {
 			if(i!=1) {
 			  if(((i-1)%8)==0) printk(" ");
 			  if(((i-1)%16)==0) printk("\n");
 			}
 			printk(" %02x",buf[i]);
 		}
 		printk("\n");
 	}
 	return 0;
 }

 // Return: 1 (is a bt832), 0 (No bt832 here)
 int bt832_init(struct i2c_client *i2c_client_s)
 {
 	unsigned char *buf;
 	int rc;

 	buf=kmalloc(65,GFP_KERNEL);
 	bt832_hexdump(i2c_client_s,buf);

 	if(buf[0x40] != 0x31) {
 		printk("bt832: this i2c chip is no bt832 (id=%02x). Detaching.\n",buf[0x40]);
 		kfree(buf);
 		return 0;
 	}

 	printk("Write 0 tp VPSTATUS\n");
 	buf[0]=BT832_VP_STATUS; // Reg.52
 	buf[1]= 0x00;
 	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
 		printk("bt832: i2c i/o error VPS: rc == %d (should be 2)\n",rc);

 	bt832_hexdump(i2c_client_s,buf);


 	// Leave low power mode:
 	printk("Bt832: leave low power mode.\n");
 	buf[0]=BT832_CAM_SETUP0; //0x39 57
 	buf[1]=0x08;
 	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
 		printk("bt832: i2c i/o error LLPM: rc == %d (should be 2)\n",rc);

 	bt832_hexdump(i2c_client_s,buf);

 	printk("Write 0 tp VPSTATUS\n");
 	buf[0]=BT832_VP_STATUS; // Reg.52
 	buf[1]= 0x00;
 	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
 		printk("bt832: i2c i/o error VPS: rc == %d (should be 2)\n",rc);

 	bt832_hexdump(i2c_client_s,buf);


 	// Enable Output
 	printk("Enable Output\n");
 	buf[0]=BT832_VP_CONTROL1; // Reg.40
 	buf[1]= 0x27 & (~0x01); // Default | !skip
 	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
 		printk("bt832: i2c i/o error EO: rc == %d (should be 2)\n",rc);

 	bt832_hexdump(i2c_client_s,buf);


 	// for testing (even works when no camera attached)
 	printk("bt832: *** Generate NTSC M Bars *****\n");
 	buf[0]=BT832_VP_TESTCONTROL0; // Reg. 42
 	buf[1]=3; // Generate NTSC System M bars, Generate Frame timing internally
 	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
 		printk("bt832: i2c i/o error MBAR: rc == %d (should be 2)\n",rc);

 	printk("Bt832: Camera Present: %s\n",
 		(buf[1+BT832_CAM_STATUS] & BT832_56_CAMERA_PRESENT) ? "yes":"no");

 	bt832_hexdump(i2c_client_s,buf);
 	kfree(buf);
 	return 1;
 }


 static int bt832_attach(struct i2c_adapter *adap, int addr, int kind)
 {
 	struct bt832 *t;

 	printk("bt832_attach\n");

 	client_template.adapter = adap;
 	client_template.addr    = addr;

 	printk("bt832: chip found @ 0x%x\n", addr<<1);

 	if (NULL == (t = kmalloc(sizeof(*t), GFP_KERNEL)))
 		return -ENOMEM;
 	memset(t,0,sizeof(*t));
 	t->client = client_template;
 	i2c_set_clientdata(&t->client, t);
 	i2c_attach_client(&t->client);

 	if(! bt832_init(&t->client)) {
 		bt832_detach(&t->client);
 		return -1;
 	}

 	return 0;
 }

 static int bt832_probe(struct i2c_adapter *adap)
 {
 #ifdef I2C_CLASS_TV_ANALOG
 	if (adap->class & I2C_CLASS_TV_ANALOG)
 		return i2c_probe(adap, &addr_data, bt832_attach);
 #else
 	if (adap->id == I2C_HW_B_BT848)
 		return i2c_probe(adap, &addr_data, bt832_attach);
 #endif
 	return 0;
 }

 static int bt832_detach(struct i2c_client *client)
 {
 	struct bt832 *t = i2c_get_clientdata(client);

 	printk("bt832: detach.\n");
 	i2c_detach_client(client);
 	kfree(t);
 	return 0;
 }

 static int
 bt832_command(struct i2c_client *client, unsigned int cmd, void *arg)
 {
 	struct bt832 *t = i2c_get_clientdata(client);

 	printk("bt832: command %x\n",cmd);

 	switch (cmd) {
 		case BT832_HEXDUMP: {
 			unsigned char *buf;
 			buf=kmalloc(65,GFP_KERNEL);
 			bt832_hexdump(&t->client,buf);
 			kfree(buf);
 		}
 		break;
 		case BT832_REATTACH:
 			printk("bt832: re-attach\n");
 			i2c_del_driver(&driver);
 			i2c_add_driver(&driver);
 		break;
 	}
 	return 0;
 }

 /* ----------------------------------------------------------------------- */

 static struct i2c_driver driver = {
 	.owner          = THIS_MODULE,
 	.name           = "i2c bt832 driver",
 	.id             = -1, /* FIXME */
 	.flags          = I2C_DF_NOTIFY,
 	.attach_adapter = bt832_probe,
 	.detach_client  = bt832_detach,
 	.command        = bt832_command,
 };
 static struct i2c_client client_template =
 {
 	.name       = "bt832",
 	.flags      = I2C_CLIENT_ALLOW_USE,
 	.driver     = &driver,
 };


 static int __init bt832_init_module(void)
 {
 	return i2c_add_driver(&driver);
 }

 static void __exit bt832_cleanup_module(void)
 {
 	i2c_del_driver(&driver);
 }

 module_init(bt832_init_module);
 module_exit(bt832_cleanup_module);

 /*
  * Overrides for Emacs so that we follow Linus's tabbing style.
  * ---------------------------------------------------------------------------
  * Local variables:
  * c-basic-offset: 8
  * End:
  */
	/* Driver for Bt832 CMOS Camera Video Processor
	i2c-addresses: 0x88 or 0x8a

	The BT832 interfaces to a Quartzsight Digital Camera (352x288, 25 or 30 fps)
	via a 9 pin connector ( 4-wire SDATA, 2-wire i2c, SCLK, VCC, GND).
	It outputs an 8-bit 4:2:2 YUV or YCrCb video signal which can be directly
	connected to bt848/bt878 GPIO pins on this purpose.
	(see: VLSI Vision Ltd. www.vvl.co.uk for camera datasheets)

	Supported Cards:
	- Pixelview Rev.4E: 0x8a
	GPIO 0x400000 toggles Bt832 RESET, and the chip changes to i2c 0x88 !

	(c) Gunther Mayer, 2002

	STATUS:
	- detect chip and hexdump
	- reset chip and leave low power mode
	- detect camera present

	TODO:
	- make it work (find correct setup for Bt832 and Bt878)
	*/

	#include <linux/module.h>
	#include <linux/kernel.h>
	#include <linux/i2c.h>
	#include <linux/types.h>
	#include <linux/videodev.h>
	#include <linux/init.h>
	#include <linux/errno.h>
	#include <linux/slab.h>

	#include <media/audiochip.h>
	#include "bttv.h"
	#include "bt832.h"

	MODULE_LICENSE("GPL");

	/* Addresses to scan */
	static unsigned short normal_i2c[] = { I2C_BT832_ALT1>>1, I2C_BT832_ALT2>>1,
	I2C_CLIENT_END };
	I2C_CLIENT_INSMOD;

	/* ---------------------------------------------------------------------- */

	#define dprintk if (debug) printk

	static int bt832_detach(struct i2c_client *client);


	static struct i2c_driver driver;
	static struct i2c_client client_template;

	struct bt832 {
	struct i2c_client client;
	};

	int bt832_hexdump(struct i2c_client i2c_client_s, unsigned char buf)
	{
	int i,rc;
	buf[0]=0x80; // start at register 0 with auto-increment
	if (1 != (rc = i2c_master_send(i2c_client_s,buf,1)))
	printk("bt832: i2c i/o error: rc == %d (should be 1)\n",rc);

	for(i=0;i<65;i++)
	buf[i]=0;
	if (65 != (rc=i2c_master_recv(i2c_client_s,buf,65)))
	printk("bt832: i2c i/o error: rc == %d (should be 65)\n",rc);

	// Note: On READ the first byte is the current index
	// (e.g. 0x80, what we just wrote)

	if(1) {
	int i;
	printk("BT832 hexdump:\n");
	for(i=1;i<65;i++) {
	if(i!=1) {
	if(((i-1)%8)==0) printk(" ");
	if(((i-1)%16)==0) printk("\n");
	}
	printk(" %02x",buf[i]);
	}
	printk("\n");
	}
	return 0;
	}

	// Return: 1 (is a bt832), 0 (No bt832 here)
	int bt832_init(struct i2c_client *i2c_client_s)
	{
	unsigned char *buf;
	int rc;

	buf=kmalloc(65,GFP_KERNEL);
	bt832_hexdump(i2c_client_s,buf);

	if(buf[0x40] != 0x31) {
	printk("bt832: this i2c chip is no bt832 (id=%02x). Detaching.\n",buf[0x40]);
	kfree(buf);
	return 0;
	}

	printk("Write 0 tp VPSTATUS\n");
	buf[0]=BT832_VP_STATUS; // Reg.52
	buf[1]= 0x00;
	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
	printk("bt832: i2c i/o error VPS: rc == %d (should be 2)\n",rc);

	bt832_hexdump(i2c_client_s,buf);


	// Leave low power mode:
	printk("Bt832: leave low power mode.\n");
	buf[0]=BT832_CAM_SETUP0; //0x39 57
	buf[1]=0x08;
	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
	printk("bt832: i2c i/o error LLPM: rc == %d (should be 2)\n",rc);

	bt832_hexdump(i2c_client_s,buf);

	printk("Write 0 tp VPSTATUS\n");
	buf[0]=BT832_VP_STATUS; // Reg.52
	buf[1]= 0x00;
	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
	printk("bt832: i2c i/o error VPS: rc == %d (should be 2)\n",rc);

	bt832_hexdump(i2c_client_s,buf);


	// Enable Output
	printk("Enable Output\n");
	buf[0]=BT832_VP_CONTROL1; // Reg.40
	buf[1]= 0x27 & (~0x01); // Default \| !skip
	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
	printk("bt832: i2c i/o error EO: rc == %d (should be 2)\n",rc);

	bt832_hexdump(i2c_client_s,buf);


	// for testing (even works when no camera attached)
	printk("bt832: * Generate NTSC M Bars ***\n");
	buf[0]=BT832_VP_TESTCONTROL0; // Reg. 42
	buf[1]=3; // Generate NTSC System M bars, Generate Frame timing internally
	if (2 != (rc = i2c_master_send(i2c_client_s,buf,2)))
	printk("bt832: i2c i/o error MBAR: rc == %d (should be 2)\n",rc);

	printk("Bt832: Camera Present: %s\n",
	(buf[1+BT832_CAM_STATUS] & BT832_56_CAMERA_PRESENT) ? "yes":"no");

	bt832_hexdump(i2c_client_s,buf);
	kfree(buf);
	return 1;
	}



	static int bt832_attach(struct i2c_adapter *adap, int addr, int kind)
	{
	struct bt832 *t;

	printk("bt832_attach\n");

	client_template.adapter = adap;
	client_template.addr = addr;

	printk("bt832: chip found @ 0x%x\n", addr<<1);

	if (NULL == (t = kmalloc(sizeof(*t), GFP_KERNEL)))
	return -ENOMEM;
	memset(t,0,sizeof(*t));
	t->client = client_template;
	i2c_set_clientdata(&t->client, t);
	i2c_attach_client(&t->client);

	if(! bt832_init(&t->client)) {
	bt832_detach(&t->client);
	return -1;
	}

	return 0;
	}

	static int bt832_probe(struct i2c_adapter *adap)
	{
	#ifdef I2C_CLASS_TV_ANALOG
	if (adap->class & I2C_CLASS_TV_ANALOG)
	return i2c_probe(adap, &addr_data, bt832_attach);
	#else
	if (adap->id == I2C_HW_B_BT848)
	return i2c_probe(adap, &addr_data, bt832_attach);
	#endif
	return 0;
	}

	static int bt832_detach(struct i2c_client *client)
	{
	struct bt832 *t = i2c_get_clientdata(client);

	printk("bt832: detach.\n");
	i2c_detach_client(client);
	kfree(t);
	return 0;
	}

	static int
	bt832_command(struct i2c_client client, unsigned int cmd, void arg)
	{
	struct bt832 *t = i2c_get_clientdata(client);

	printk("bt832: command %x\n",cmd);

	switch (cmd) {
	case BT832_HEXDUMP: {
	unsigned char *buf;
	buf=kmalloc(65,GFP_KERNEL);
	bt832_hexdump(&t->client,buf);
	kfree(buf);
	}
	break;
	case BT832_REATTACH:
	printk("bt832: re-attach\n");
	i2c_del_driver(&driver);
	i2c_add_driver(&driver);
	break;
	}
	return 0;
	}

	/* ----------------------------------------------------------------------- */

	static struct i2c_driver driver = {
	.owner = THIS_MODULE,
	.name = "i2c bt832 driver",
	.id = -1, /* FIXME */
	.flags = I2C_DF_NOTIFY,
	.attach_adapter = bt832_probe,
	.detach_client = bt832_detach,
	.command = bt832_command,
	};
	static struct i2c_client client_template =
	{
	.name = "bt832",
	.flags = I2C_CLIENT_ALLOW_USE,
	.driver = &driver,
	};


	static int __init bt832_init_module(void)
	{
	return i2c_add_driver(&driver);
	}

	static void __exit bt832_cleanup_module(void)
	{
	i2c_del_driver(&driver);
	}

	module_init(bt832_init_module);
	module_exit(bt832_cleanup_module);

	/*
	* Overrides for Emacs so that we follow Linus's tabbing style.
	* ---------------------------------------------------------------------------
	* Local variables:
	* c-basic-offset: 8
	* End:
	*/