V4L/DVB: em28xx: add Dikom DK300 hybrid USB tuner
Adds digital and analogue tv support for Dikom DK300 hybrid usb card.
Not working: remote controller
To be done: it seems that with the proposed patch the digital demodulator
remains activated if the tuner is switched from digital to analogue mode.
Workaround is to unplug and replug the device when switching from digital to
analogue. If someone can explain how to verify the gpio settings using the
usbsnoop, the above issue perhaps can be resolved.
Signed-off-by: Andrea Amorosi <Andrea.Amorosi76@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index 62ca31d..48d7f7e 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -232,6 +232,12 @@
{ -1, -1, -1, -1},
};
+static struct em28xx_reg_seq dikom_dk300_digital[] = {
+ {EM28XX_R08_GPIO, 0x6e, ~EM_GPIO_4, 10},
+ {EM2880_R04_GPO, 0x08, 0xff, 10},
+ { -1, -1, -1, -1},
+};
+
/*
* Board definitions
@@ -1440,6 +1446,21 @@
.gpio = hauppauge_wintv_hvr_900_analog,
} },
},
+ [EM2882_BOARD_DIKOM_DK300] = {
+ .name = "Dikom DK300",
+ .tuner_type = TUNER_XC2028,
+ .tuner_gpio = default_tuner_gpio,
+ .decoder = EM28XX_TVP5150,
+ .mts_firmware = 1,
+ .has_dvb = 1,
+ .dvb_gpio = dikom_dk300_digital,
+ .input = { {
+ .type = EM28XX_VMUX_TELEVISION,
+ .vmux = TVP5150_COMPOSITE0,
+ .amux = EM28XX_AMUX_VIDEO,
+ .gpio = default_analog,
+ } },
+ },
[EM2883_BOARD_KWORLD_HYBRID_330U] = {
.name = "Kworld PlusTV HD Hybrid 330",
.tuner_type = TUNER_XC2028,
@@ -1760,6 +1781,7 @@
{0xcee44a99, EM2882_BOARD_EVGA_INDTUBE, TUNER_XC2028},
{0xb8846b20, EM2881_BOARD_PINNACLE_HYBRID_PRO, TUNER_XC2028},
{0x63f653bd, EM2870_BOARD_REDDO_DVB_C_USB_BOX, TUNER_ABSENT},
+ {0x4e913442, EM2882_BOARD_DIKOM_DK300, TUNER_XC2028},
};
/* I2C devicelist hash table for devices with generic USB IDs */
@@ -2112,6 +2134,7 @@
ctl->demod = XC3028_FE_DEFAULT;
break;
case EM2883_BOARD_KWORLD_HYBRID_330U:
+ case EM2882_BOARD_DIKOM_DK300:
ctl->demod = XC3028_FE_CHINA;
ctl->fname = XC2028_DEFAULT_FIRMWARE;
break;
@@ -2397,6 +2420,31 @@
em28xx_gpio_set(dev, dev->board.tuner_gpio);
em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
break;
+
+/*
+ * The Dikom DK300 is detected as an Kworld VS-DVB-T 323UR.
+ *
+ * This occurs because they share identical USB vendor and
+ * product IDs.
+ *
+ * What we do here is look up the EEPROM hash of the Dikom
+ * and if it is found then we decide that we do not have
+ * a Kworld and reset the device to the Dikom instead.
+ *
+ * This solution is only valid if they do not share eeprom
+ * hash identities which has not been determined as yet.
+ */
+ case EM2882_BOARD_KWORLD_VS_DVBT:
+ if (!em28xx_hint_board(dev))
+ em28xx_set_model(dev);
+
+ /* In cases where we had to use a board hint, the call to
+ em28xx_set_mode() in em28xx_pre_card_setup() was a no-op,
+ so make the call now so the analog GPIOs are set properly
+ before probing the i2c bus. */
+ em28xx_gpio_set(dev, dev->board.tuner_gpio);
+ em28xx_set_mode(dev, EM28XX_ANALOG_MODE);
+ break;
}
#if defined(CONFIG_MODULES) && defined(MODULE)