| # |
| # Physical Layer USB driver configuration |
| # |
| menu "USB Physical Layer drivers" |
| |
| config USB_PHY |
| def_bool n |
| |
| config USB_OTG_WAKELOCK |
| bool "Hold a wakelock when USB connected" |
| depends on WAKELOCK |
| select USB_OTG_UTILS |
| help |
| Select this to automatically hold a wakelock when USB is |
| connected, preventing suspend. |
| |
| # |
| # USB Transceiver Drivers |
| # |
| config AB8500_USB |
| tristate "AB8500 USB Transceiver Driver" |
| depends on AB8500_CORE |
| select USB_PHY |
| help |
| Enable this to support the USB OTG transceiver in AB8500 chip. |
| This transceiver supports high and full speed devices plus, |
| in host mode, low speed. |
| |
| config FSL_USB2_OTG |
| bool "Freescale USB OTG Transceiver Driver" |
| depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' |
| select USB_PHY |
| help |
| Enable this to support Freescale USB OTG transceiver. |
| |
| config ISP1301_OMAP |
| tristate "Philips ISP1301 with OMAP OTG" |
| depends on I2C && ARCH_OMAP_OTG |
| depends on USB |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' |
| select USB_PHY |
| help |
| If you say yes here you get support for the Philips ISP1301 |
| USB-On-The-Go transceiver working with the OMAP OTG controller. |
| The ISP1301 is a full speed USB transceiver which is used in |
| products including H2, H3, and H4 development boards for Texas |
| Instruments OMAP processors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called phy-isp1301-omap. |
| |
| config KEYSTONE_USB_PHY |
| tristate "Keystone USB PHY Driver" |
| depends on ARCH_KEYSTONE || COMPILE_TEST |
| depends on NOP_USB_XCEIV |
| help |
| Enable this to support Keystone USB phy. This driver provides |
| interface to interact with USB 2.0 and USB 3.0 PHY that is part |
| of the Keystone SOC. |
| |
| config NOP_USB_XCEIV |
| tristate "NOP USB Transceiver Driver" |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in |
| select USB_PHY |
| help |
| This driver is to be used by all the usb transceiver which are either |
| built-in with usb ip or which are autonomous and doesn't require any |
| phy programming such as ISP1x04 etc. |
| |
| config AM335X_CONTROL_USB |
| tristate |
| |
| config AM335X_PHY_USB |
| tristate "AM335x USB PHY Driver" |
| depends on ARM || COMPILE_TEST |
| depends on NOP_USB_XCEIV |
| select USB_PHY |
| select AM335X_CONTROL_USB |
| select USB_COMMON |
| help |
| This driver provides PHY support for that phy which part for the |
| AM335x SoC. |
| |
| config SAMSUNG_USBPHY |
| tristate |
| help |
| Enable this to support Samsung USB phy helper driver for Samsung SoCs. |
| This driver provides common interface to interact, for Samsung USB 2.0 PHY |
| driver and later for Samsung USB 3.0 PHY driver. |
| |
| config TWL6030_USB |
| tristate "TWL6030 USB Transceiver Driver" |
| depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS |
| help |
| Enable this to support the USB OTG transceiver on TWL6030 |
| family chips. This TWL6030 transceiver has the VBUS and ID GND |
| and OTG SRP events capabilities. For all other transceiver functionality |
| UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs |
| are hooked to this driver through platform_data structure. |
| The definition of internal PHY APIs are in the mach-omap2 layer. |
| |
| config USB_GPIO_VBUS |
| tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" |
| depends on GPIOLIB || COMPILE_TEST |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' |
| select USB_PHY |
| help |
| Provides simple GPIO VBUS sensing for controllers with an |
| internal transceiver via the usb_phy interface, and |
| optionally control of a D+ pullup GPIO as well as a VBUS |
| current limit regulator. |
| |
| config OMAP_OTG |
| tristate "OMAP USB OTG controller driver" |
| depends on ARCH_OMAP_OTG && EXTCON |
| help |
| Enable this to support some transceivers on OMAP1 platforms. OTG |
| controller is needed to switch between host and peripheral modes. |
| |
| This driver can also be built as a module. If so, the module |
| will be called phy-omap-otg. |
| |
| config TAHVO_USB |
| tristate "Tahvo USB transceiver driver" |
| depends on MFD_RETU && EXTCON |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' |
| select USB_PHY |
| help |
| Enable this to support USB transceiver on Tahvo. This is used |
| at least on Nokia 770. |
| |
| config TAHVO_USB_HOST_BY_DEFAULT |
| depends on TAHVO_USB |
| bool "Device in USB host mode by default" |
| help |
| Say Y here, if you want the device to enter USB host mode |
| by default on bootup. |
| |
| config USB_ISP1301 |
| tristate "NXP ISP1301 USB transceiver support" |
| depends on USB || USB_GADGET |
| depends on I2C |
| select USB_PHY |
| help |
| Say Y here to add support for the NXP ISP1301 USB transceiver driver. |
| This chip is typically used as USB transceiver for USB host, gadget |
| and OTG drivers (to be selected separately). |
| |
| To compile this driver as a module, choose M here: the |
| module will be called phy-isp1301. |
| |
| config USB_MSM_OTG |
| tristate "Qualcomm on-chip USB OTG controller support" |
| depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST) |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' |
| depends on RESET_CONTROLLER |
| depends on EXTCON |
| select USB_PHY |
| help |
| Enable this to support the USB OTG transceiver on Qualcomm chips. It |
| handles PHY initialization, clock management, and workarounds |
| required after resetting the hardware and power management. |
| This driver is required even for peripheral only or host only |
| mode configurations. |
| This driver is not supported on boards like trout which |
| has an external PHY. |
| |
| config USB_QCOM_8X16_PHY |
| tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support" |
| depends on ARCH_QCOM || COMPILE_TEST |
| depends on RESET_CONTROLLER && EXTCON |
| select USB_PHY |
| select USB_ULPI_VIEWPORT |
| help |
| Enable this to support the USB transceiver on Qualcomm 8x16 chipsets. |
| It handles PHY initialization, clock management, power management, |
| and workarounds required after resetting the hardware. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called phy-qcom-8x16-usb. |
| |
| config USB_MV_OTG |
| tristate "Marvell USB OTG support" |
| depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG |
| depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' |
| select USB_PHY |
| help |
| Say Y here if you want to build Marvell USB OTG transciever |
| driver in kernel (including PXA and MMP series). This driver |
| implements role switch between EHCI host driver and gadget driver. |
| |
| To compile this driver as a module, choose M here. |
| |
| config USB_MXS_PHY |
| tristate "Freescale MXS USB PHY support" |
| depends on ARCH_MXC || ARCH_MXS |
| select STMP_DEVICE |
| select USB_PHY |
| help |
| Enable this to support the Freescale MXS USB PHY. |
| |
| MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. |
| |
| config USB_ULPI |
| bool "Generic ULPI Transceiver Driver" |
| depends on ARM || ARM64 |
| select USB_ULPI_VIEWPORT |
| help |
| Enable this to support ULPI connected USB OTG transceivers which |
| are likely found on embedded boards. |
| |
| config USB_ULPI_VIEWPORT |
| bool |
| help |
| Provides read/write operations to the ULPI phy register set for |
| controllers with a viewport register (e.g. Chipidea/ARC controllers). |
| |
| config DUAL_ROLE_USB_INTF |
| bool "Generic DUAL ROLE sysfs interface" |
| depends on SYSFS && USB_PHY |
| help |
| A generic sysfs interface to track and change the state of |
| dual role usb phys. The usb phy drivers can register to |
| this interface to expose it capabilities to the userspace |
| and thereby allowing userspace to change the port mode. |
| |
| config USB_MSM_SSPHY_QMP |
| tristate "MSM SSUSB QMP PHY Driver" |
| depends on ARCH_QCOM |
| select USB_PHY |
| help |
| Enable this to support the SuperSpeed USB transceiver on MSM chips. |
| This driver supports the PHY which uses the QSCRATCH-based register |
| set for its control sequences, normally paired with newer DWC3-based |
| SuperSpeed controllers. |
| |
| config MSM_QUSB_PHY |
| tristate "MSM QUSB2 PHY Driver" |
| depends on ARCH_QCOM |
| select USB_PHY |
| help |
| Enable this to support the QUSB2 PHY on MSM chips. This driver supports |
| the high-speed PHY which is usually paired with either the ChipIdea or |
| Synopsys DWC3 USB IPs on MSM SOCs. This driver expects to configure the |
| PHY with a dedicated register I/O memory region. |
| |
| endmenu |