usb: phy: qcom: Switch to new extcon framework API
[un]register_interest and reading cable state by
name have been deprecated. Switch to new API.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
diff --git a/drivers/usb/phy/phy-qcom-8x16-usb.c b/drivers/usb/phy/phy-qcom-8x16-usb.c
index 5d357a9..579587d 100644
--- a/drivers/usb/phy/phy-qcom-8x16-usb.c
+++ b/drivers/usb/phy/phy-qcom-8x16-usb.c
@@ -71,7 +71,7 @@
struct reset_control *phy_reset;
- struct extcon_specific_cable_nb vbus_cable;
+ struct extcon_dev *vbus_edev;
struct notifier_block vbus_notify;
struct gpio_desc *switch_gpio;
@@ -234,7 +234,7 @@
val = ULPI_PWR_OTG_COMP_DISABLE;
usb_phy_io_write(phy, val, ULPI_SET(ULPI_PWR_CLK_MNG_REG));
- state = extcon_get_cable_state(qphy->vbus_cable.edev, "USB");
+ state = extcon_get_cable_state_(qphy->vbus_edev, EXTCON_USB);
if (state)
phy_8x16_vbus_on(qphy);
else
@@ -314,7 +314,6 @@
static int phy_8x16_probe(struct platform_device *pdev)
{
- struct extcon_dev *edev;
struct phy_8x16 *qphy;
struct resource *res;
struct usb_phy *phy;
@@ -349,9 +348,9 @@
if (ret < 0)
return ret;
- edev = extcon_get_edev_by_phandle(phy->dev, 0);
- if (IS_ERR(edev))
- return PTR_ERR(edev);
+ qphy->vbus_edev = extcon_get_edev_by_phandle(phy->dev, 0);
+ if (IS_ERR(qphy->vbus_edev))
+ return PTR_ERR(qphy->vbus_edev);
ret = clk_set_rate(qphy->core_clk, INT_MAX);
if (ret < 0)
@@ -370,8 +369,8 @@
goto off_clks;
qphy->vbus_notify.notifier_call = phy_8x16_vbus_notify;
- ret = extcon_register_interest(&qphy->vbus_cable, edev->name,
- "USB", &qphy->vbus_notify);
+ ret = extcon_register_notifier(qphy->vbus_edev, EXTCON_USB,
+ &qphy->vbus_notify);
if (ret < 0)
goto off_power;
@@ -385,7 +384,8 @@
return 0;
off_extcon:
- extcon_unregister_interest(&qphy->vbus_cable);
+ extcon_unregister_notifier(qphy->vbus_edev, EXTCON_USB,
+ &qphy->vbus_notify);
off_power:
phy_8x16_regulators_disable(qphy);
off_clks:
@@ -400,7 +400,8 @@
struct phy_8x16 *qphy = platform_get_drvdata(pdev);
unregister_reboot_notifier(&qphy->reboot_notify);
- extcon_unregister_interest(&qphy->vbus_cable);
+ extcon_unregister_notifier(qphy->vbus_edev, EXTCON_USB,
+ &qphy->vbus_notify);
/*
* Ensure that D+/D- lines are routed to uB connector, so