mfd: stmpe: add pull up/down register offsets for STMPE
This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index 02a17c3..2d29d17 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -519,6 +519,7 @@
[STMPE_IDX_GPDR_LSB] = STMPE1601_REG_GPIO_SET_DIR_LSB,
[STMPE_IDX_GPRER_LSB] = STMPE1601_REG_GPIO_RE_LSB,
[STMPE_IDX_GPFER_LSB] = STMPE1601_REG_GPIO_FE_LSB,
+ [STMPE_IDX_GPPUR_LSB] = STMPE1601_REG_GPIO_PU_LSB,
[STMPE_IDX_GPAFR_U_MSB] = STMPE1601_REG_GPIO_AF_U_MSB,
[STMPE_IDX_IEGPIOR_LSB] = STMPE1601_REG_INT_EN_GPIO_MASK_LSB,
[STMPE_IDX_ISGPIOR_MSB] = STMPE1601_REG_INT_STA_GPIO_MSB,
@@ -667,6 +668,7 @@
[STMPE_IDX_GPDR_LSB] = STMPE1801_REG_GPIO_SET_DIR_LOW,
[STMPE_IDX_GPRER_LSB] = STMPE1801_REG_GPIO_RE_LOW,
[STMPE_IDX_GPFER_LSB] = STMPE1801_REG_GPIO_FE_LOW,
+ [STMPE_IDX_GPPUR_LSB] = STMPE1801_REG_GPIO_PULL_UP_LOW,
[STMPE_IDX_IEGPIOR_LSB] = STMPE1801_REG_INT_EN_GPIO_MASK_LOW,
[STMPE_IDX_ISGPIOR_LSB] = STMPE1801_REG_INT_STA_GPIO_LOW,
};
@@ -750,6 +752,8 @@
[STMPE_IDX_GPDR_LSB] = STMPE24XX_REG_GPDR_LSB,
[STMPE_IDX_GPRER_LSB] = STMPE24XX_REG_GPRER_LSB,
[STMPE_IDX_GPFER_LSB] = STMPE24XX_REG_GPFER_LSB,
+ [STMPE_IDX_GPPUR_LSB] = STMPE24XX_REG_GPPUR_LSB,
+ [STMPE_IDX_GPPDR_LSB] = STMPE24XX_REG_GPPDR_LSB,
[STMPE_IDX_GPAFR_U_MSB] = STMPE24XX_REG_GPAFR_U_MSB,
[STMPE_IDX_IEGPIOR_LSB] = STMPE24XX_REG_IEGPIOR_LSB,
[STMPE_IDX_ISGPIOR_MSB] = STMPE24XX_REG_ISGPIOR_MSB,