| /* sun3lance.c: Ethernet driver for SUN3 Lance chip */ |
| /* |
| |
| Sun3 Lance ethernet driver, by Sam Creasey (sammy@users.qual.net). |
| This driver is a part of the linux kernel, and is thus distributed |
| under the GNU General Public License. |
| |
| The values used in LANCE_OBIO and LANCE_IRQ seem to be empirically |
| true for the correct IRQ and address of the lance registers. They |
| have not been widely tested, however. What we probably need is a |
| "proper" way to search for a device in the sun3's prom, but, alas, |
| linux has no such thing. |
| |
| This driver is largely based on atarilance.c, by Roman Hodek. Other |
| sources of inspiration were the NetBSD sun3 am7990 driver, and the |
| linux sparc lance driver (sunlance.c). |
| |
| There are more assumptions made throughout this driver, it almost |
| certainly still needs work, but it does work at least for RARP/BOOTP and |
| mounting the root NFS filesystem. |
| |
| */ |
| |
| static char *version = "sun3lance.c: v1.2 1/12/2001 Sam Creasey (sammy@sammy.net)\n"; |
| |
| #include <linux/module.h> |
| #include <linux/stddef.h> |
| #include <linux/kernel.h> |
| #include <linux/string.h> |
| #include <linux/errno.h> |
| #include <linux/slab.h> |
| #include <linux/interrupt.h> |
| #include <linux/init.h> |
| #include <linux/ioport.h> |
| #include <linux/delay.h> |
| #include <linux/netdevice.h> |
| #include <linux/etherdevice.h> |
| #include <linux/skbuff.h> |
| #include <linux/bitops.h> |
| |
| #include <asm/cacheflush.h> |
| #include <asm/setup.h> |
| #include <asm/irq.h> |
| #include <asm/io.h> |
| #include <asm/pgtable.h> |
| #include <asm/dvma.h> |
| #include <asm/idprom.h> |
| #include <asm/machines.h> |
| |
| #ifdef CONFIG_SUN3 |
| #include <asm/sun3mmu.h> |
| #else |
| #include <asm/sun3xprom.h> |
| #endif |
| |
| /* sun3/60 addr/irq for the lance chip. If your sun is different, |
| change this. */ |
| #define LANCE_OBIO 0x120000 |
| #define LANCE_IRQ IRQ_AUTO_3 |
| |
| /* Debug level: |
| * 0 = silent, print only serious errors |
| * 1 = normal, print error messages |
| * 2 = debug, print debug infos |
| * 3 = debug, print even more debug infos (packet data) |
| */ |
| |
| #define LANCE_DEBUG 0 |
| |
| #ifdef LANCE_DEBUG |
| static int lance_debug = LANCE_DEBUG; |
| #else |
| static int lance_debug = 1; |
| #endif |
| module_param(lance_debug, int, 0); |
| MODULE_PARM_DESC(lance_debug, "SUN3 Lance debug level (0-3)"); |
| MODULE_LICENSE("GPL"); |
| |
| #define DPRINTK(n,a) \ |
| do { \ |
| if (lance_debug >= n) \ |
| printk a; \ |
| } while( 0 ) |
| |
| |
| /* we're only using 32k of memory, so we use 4 TX |
| buffers and 16 RX buffers. These values are expressed as log2. */ |
| |
| #define TX_LOG_RING_SIZE 3 |
| #define RX_LOG_RING_SIZE 5 |
| |
| /* These are the derived values */ |
| |
| #define TX_RING_SIZE (1 << TX_LOG_RING_SIZE) |
| #define TX_RING_LEN_BITS (TX_LOG_RING_SIZE << 5) |
| #define TX_RING_MOD_MASK (TX_RING_SIZE - 1) |
| |
| #define RX_RING_SIZE (1 << RX_LOG_RING_SIZE) |
| #define RX_RING_LEN_BITS (RX_LOG_RING_SIZE << 5) |
| #define RX_RING_MOD_MASK (RX_RING_SIZE - 1) |
| |
| /* Definitions for packet buffer access: */ |
| #define PKT_BUF_SZ 1544 |
| |
| /* Get the address of a packet buffer corresponding to a given buffer head */ |
| #define PKTBUF_ADDR(head) (void *)((unsigned long)(MEM) | (head)->base) |
| |
| |
| /* The LANCE Rx and Tx ring descriptors. */ |
| struct lance_rx_head { |
| unsigned short base; /* Low word of base addr */ |
| volatile unsigned char flag; |
| unsigned char base_hi; /* High word of base addr (unused) */ |
| short buf_length; /* This length is 2s complement! */ |
| volatile short msg_length; /* This length is "normal". */ |
| }; |
| |
| struct lance_tx_head { |
| unsigned short base; /* Low word of base addr */ |
| volatile unsigned char flag; |
| unsigned char base_hi; /* High word of base addr (unused) */ |
| short length; /* Length is 2s complement! */ |
| volatile short misc; |
| }; |
| |
| /* The LANCE initialization block, described in databook. */ |
| struct lance_init_block { |
| unsigned short mode; /* Pre-set mode */ |
| unsigned char hwaddr[6]; /* Physical ethernet address */ |
| unsigned int filter[2]; /* Multicast filter (unused). */ |
| /* Receive and transmit ring base, along with length bits. */ |
| unsigned short rdra; |
| unsigned short rlen; |
| unsigned short tdra; |
| unsigned short tlen; |
| unsigned short pad[4]; /* is thie needed? */ |
| }; |
| |
| /* The whole layout of the Lance shared memory */ |
| struct lance_memory { |
| struct lance_init_block init; |
| struct lance_tx_head tx_head[TX_RING_SIZE]; |
| struct lance_rx_head rx_head[RX_RING_SIZE]; |
| char rx_data[RX_RING_SIZE][PKT_BUF_SZ]; |
| char tx_data[TX_RING_SIZE][PKT_BUF_SZ]; |
| }; |
| |
| /* The driver's private device structure */ |
| |
| struct lance_private { |
| volatile unsigned short *iobase; |
| struct lance_memory *mem; |
| int new_rx, new_tx; /* The next free ring entry */ |
| int old_tx, old_rx; /* ring entry to be processed */ |
| /* These two must be longs for set_bit() */ |
| long tx_full; |
| long lock; |
| }; |
| |
| /* I/O register access macros */ |
| |
| #define MEM lp->mem |
| #define DREG lp->iobase[0] |
| #define AREG lp->iobase[1] |
| #define REGA(a) (*( AREG = (a), &DREG )) |
| |
| /* Definitions for the Lance */ |
| |
| /* tx_head flags */ |
| #define TMD1_ENP 0x01 /* end of packet */ |
| #define TMD1_STP 0x02 /* start of packet */ |
| #define TMD1_DEF 0x04 /* deferred */ |
| #define TMD1_ONE 0x08 /* one retry needed */ |
| #define TMD1_MORE 0x10 /* more than one retry needed */ |
| #define TMD1_ERR 0x40 /* error summary */ |
| #define TMD1_OWN 0x80 /* ownership (set: chip owns) */ |
| |
| #define TMD1_OWN_CHIP TMD1_OWN |
| #define TMD1_OWN_HOST 0 |
| |
| /* tx_head misc field */ |
| #define TMD3_TDR 0x03FF /* Time Domain Reflectometry counter */ |
| #define TMD3_RTRY 0x0400 /* failed after 16 retries */ |
| #define TMD3_LCAR 0x0800 /* carrier lost */ |
| #define TMD3_LCOL 0x1000 /* late collision */ |
| #define TMD3_UFLO 0x4000 /* underflow (late memory) */ |
| #define TMD3_BUFF 0x8000 /* buffering error (no ENP) */ |
| |
| /* rx_head flags */ |
| #define RMD1_ENP 0x01 /* end of packet */ |
| #define RMD1_STP 0x02 /* start of packet */ |
| #define RMD1_BUFF 0x04 /* buffer error */ |
| #define RMD1_CRC 0x08 /* CRC error */ |
| #define RMD1_OFLO 0x10 /* overflow */ |
| #define RMD1_FRAM 0x20 /* framing error */ |
| #define RMD1_ERR 0x40 /* error summary */ |
| #define RMD1_OWN 0x80 /* ownership (set: ship owns) */ |
| |
| #define RMD1_OWN_CHIP RMD1_OWN |
| #define RMD1_OWN_HOST 0 |
| |
| /* register names */ |
| #define CSR0 0 /* mode/status */ |
| #define CSR1 1 /* init block addr (low) */ |
| #define CSR2 2 /* init block addr (high) */ |
| #define CSR3 3 /* misc */ |
| #define CSR8 8 /* address filter */ |
| #define CSR15 15 /* promiscuous mode */ |
| |
| /* CSR0 */ |
| /* (R=readable, W=writeable, S=set on write, C=clear on write) */ |
| #define CSR0_INIT 0x0001 /* initialize (RS) */ |
| #define CSR0_STRT 0x0002 /* start (RS) */ |
| #define CSR0_STOP 0x0004 /* stop (RS) */ |
| #define CSR0_TDMD 0x0008 /* transmit demand (RS) */ |
| #define CSR0_TXON 0x0010 /* transmitter on (R) */ |
| #define CSR0_RXON 0x0020 /* receiver on (R) */ |
| #define CSR0_INEA 0x0040 /* interrupt enable (RW) */ |
| #define CSR0_INTR 0x0080 /* interrupt active (R) */ |
| #define CSR0_IDON 0x0100 /* initialization done (RC) */ |
| #define CSR0_TINT 0x0200 /* transmitter interrupt (RC) */ |
| #define CSR0_RINT 0x0400 /* receiver interrupt (RC) */ |
| #define CSR0_MERR 0x0800 /* memory error (RC) */ |
| #define CSR0_MISS 0x1000 /* missed frame (RC) */ |
| #define CSR0_CERR 0x2000 /* carrier error (no heartbeat :-) (RC) */ |
| #define CSR0_BABL 0x4000 /* babble: tx-ed too many bits (RC) */ |
| #define CSR0_ERR 0x8000 /* error (RC) */ |
| |
| /* CSR3 */ |
| #define CSR3_BCON 0x0001 /* byte control */ |
| #define CSR3_ACON 0x0002 /* ALE control */ |
| #define CSR3_BSWP 0x0004 /* byte swap (1=big endian) */ |
| |
| /***************************** Prototypes *****************************/ |
| |
| static int lance_probe( struct net_device *dev); |
| static int lance_open( struct net_device *dev ); |
| static void lance_init_ring( struct net_device *dev ); |
| static int lance_start_xmit( struct sk_buff *skb, struct net_device *dev ); |
| static irqreturn_t lance_interrupt( int irq, void *dev_id); |
| static int lance_rx( struct net_device *dev ); |
| static int lance_close( struct net_device *dev ); |
| static void set_multicast_list( struct net_device *dev ); |
| |
| /************************* End of Prototypes **************************/ |
| |
| struct net_device * __init sun3lance_probe(int unit) |
| { |
| struct net_device *dev; |
| static int found; |
| int err = -ENODEV; |
| |
| if (!MACH_IS_SUN3 && !MACH_IS_SUN3X) |
| return ERR_PTR(-ENODEV); |
| |
| /* check that this machine has an onboard lance */ |
| switch(idprom->id_machtype) { |
| case SM_SUN3|SM_3_50: |
| case SM_SUN3|SM_3_60: |
| case SM_SUN3X|SM_3_80: |
| /* these machines have lance */ |
| break; |
| |
| default: |
| return ERR_PTR(-ENODEV); |
| } |
| |
| if (found) |
| return ERR_PTR(-ENODEV); |
| |
| dev = alloc_etherdev(sizeof(struct lance_private)); |
| if (!dev) |
| return ERR_PTR(-ENOMEM); |
| if (unit >= 0) { |
| sprintf(dev->name, "eth%d", unit); |
| netdev_boot_setup_check(dev); |
| } |
| |
| if (!lance_probe(dev)) |
| goto out; |
| |
| err = register_netdev(dev); |
| if (err) |
| goto out1; |
| found = 1; |
| return dev; |
| |
| out1: |
| #ifdef CONFIG_SUN3 |
| iounmap((void __iomem *)dev->base_addr); |
| #endif |
| out: |
| free_netdev(dev); |
| return ERR_PTR(err); |
| } |
| |
| static const struct net_device_ops lance_netdev_ops = { |
| .ndo_open = lance_open, |
| .ndo_stop = lance_close, |
| .ndo_start_xmit = lance_start_xmit, |
| .ndo_set_multicast_list = set_multicast_list, |
| .ndo_set_mac_address = NULL, |
| .ndo_change_mtu = eth_change_mtu, |
| .ndo_validate_addr = eth_validate_addr, |
| }; |
| |
| static int __init lance_probe( struct net_device *dev) |
| { |
| unsigned long ioaddr; |
| |
| struct lance_private *lp; |
| int i; |
| static int did_version; |
| volatile unsigned short *ioaddr_probe; |
| unsigned short tmp1, tmp2; |
| |
| #ifdef CONFIG_SUN3 |
| ioaddr = (unsigned long)ioremap(LANCE_OBIO, PAGE_SIZE); |
| if (!ioaddr) |
| return 0; |
| #else |
| ioaddr = SUN3X_LANCE; |
| #endif |
| |
| /* test to see if there's really a lance here */ |
| /* (CSRO_INIT shouldn't be readable) */ |
| |
| ioaddr_probe = (volatile unsigned short *)ioaddr; |
| tmp1 = ioaddr_probe[0]; |
| tmp2 = ioaddr_probe[1]; |
| |
| ioaddr_probe[1] = CSR0; |
| ioaddr_probe[0] = CSR0_INIT | CSR0_STOP; |
| |
| if(ioaddr_probe[0] != CSR0_STOP) { |
| ioaddr_probe[0] = tmp1; |
| ioaddr_probe[1] = tmp2; |
| |
| #ifdef CONFIG_SUN3 |
| iounmap((void __iomem *)ioaddr); |
| #endif |
| return 0; |
| } |
| |
| lp = netdev_priv(dev); |
| |
| /* XXX - leak? */ |
| MEM = dvma_malloc_align(sizeof(struct lance_memory), 0x10000); |
| if (MEM == NULL) { |
| #ifdef CONFIG_SUN3 |
| iounmap((void __iomem *)ioaddr); |
| #endif |
| printk(KERN_WARNING "SUN3 Lance couldn't allocate DVMA memory\n"); |
| return 0; |
| } |
| |
| lp->iobase = (volatile unsigned short *)ioaddr; |
| dev->base_addr = (unsigned long)ioaddr; /* informational only */ |
| |
| REGA(CSR0) = CSR0_STOP; |
| |
| if (request_irq(LANCE_IRQ, lance_interrupt, IRQF_DISABLED, "SUN3 Lance", dev) < 0) { |
| #ifdef CONFIG_SUN3 |
| iounmap((void __iomem *)ioaddr); |
| #endif |
| dvma_free((void *)MEM); |
| printk(KERN_WARNING "SUN3 Lance unable to allocate IRQ\n"); |
| return 0; |
| } |
| dev->irq = (unsigned short)LANCE_IRQ; |
| |
| |
| printk("%s: SUN3 Lance at io %#lx, mem %#lx, irq %d, hwaddr ", |
| dev->name, |
| (unsigned long)ioaddr, |
| (unsigned long)MEM, |
| dev->irq); |
| |
| /* copy in the ethernet address from the prom */ |
| for(i = 0; i < 6 ; i++) |
| dev->dev_addr[i] = idprom->id_ethaddr[i]; |
| |
| /* tell the card it's ether address, bytes swapped */ |
| MEM->init.hwaddr[0] = dev->dev_addr[1]; |
| MEM->init.hwaddr[1] = dev->dev_addr[0]; |
| MEM->init.hwaddr[2] = dev->dev_addr[3]; |
| MEM->init.hwaddr[3] = dev->dev_addr[2]; |
| MEM->init.hwaddr[4] = dev->dev_addr[5]; |
| MEM->init.hwaddr[5] = dev->dev_addr[4]; |
| |
| printk("%pM\n", dev->dev_addr); |
| |
| MEM->init.mode = 0x0000; |
| MEM->init.filter[0] = 0x00000000; |
| MEM->init.filter[1] = 0x00000000; |
| MEM->init.rdra = dvma_vtob(MEM->rx_head); |
| MEM->init.rlen = (RX_LOG_RING_SIZE << 13) | |
| (dvma_vtob(MEM->rx_head) >> 16); |
| MEM->init.tdra = dvma_vtob(MEM->tx_head); |
| MEM->init.tlen = (TX_LOG_RING_SIZE << 13) | |
| (dvma_vtob(MEM->tx_head) >> 16); |
| |
| DPRINTK(2, ("initaddr: %08lx rx_ring: %08lx tx_ring: %08lx\n", |
| dvma_vtob(&(MEM->init)), dvma_vtob(MEM->rx_head), |
| (dvma_vtob(MEM->tx_head)))); |
| |
| if (did_version++ == 0) |
| printk( version ); |
| |
| dev->netdev_ops = &lance_netdev_ops; |
| // KLUDGE -- REMOVE ME |
| set_bit(__LINK_STATE_PRESENT, &dev->state); |
| |
| |
| return 1; |
| } |
| |
| static int lance_open( struct net_device *dev ) |
| { |
| struct lance_private *lp = netdev_priv(dev); |
| int i; |
| |
| DPRINTK( 2, ( "%s: lance_open()\n", dev->name )); |
| |
| REGA(CSR0) = CSR0_STOP; |
| |
| lance_init_ring(dev); |
| |
| /* From now on, AREG is kept to point to CSR0 */ |
| REGA(CSR0) = CSR0_INIT; |
| |
| i = 1000000; |
| while (--i > 0) |
| if (DREG & CSR0_IDON) |
| break; |
| if (i <= 0 || (DREG & CSR0_ERR)) { |
| DPRINTK( 2, ( "lance_open(): opening %s failed, i=%d, csr0=%04x\n", |
| dev->name, i, DREG )); |
| DREG = CSR0_STOP; |
| return( -EIO ); |
| } |
| |
| DREG = CSR0_IDON | CSR0_STRT | CSR0_INEA; |
| |
| netif_start_queue(dev); |
| |
| DPRINTK( 2, ( "%s: LANCE is open, csr0 %04x\n", dev->name, DREG )); |
| |
| return( 0 ); |
| } |
| |
| |
| /* Initialize the LANCE Rx and Tx rings. */ |
| |
| static void lance_init_ring( struct net_device *dev ) |
| { |
| struct lance_private *lp = netdev_priv(dev); |
| int i; |
| |
| lp->lock = 0; |
| lp->tx_full = 0; |
| lp->new_rx = lp->new_tx = 0; |
| lp->old_rx = lp->old_tx = 0; |
| |
| for( i = 0; i < TX_RING_SIZE; i++ ) { |
| MEM->tx_head[i].base = dvma_vtob(MEM->tx_data[i]); |
| MEM->tx_head[i].flag = 0; |
| MEM->tx_head[i].base_hi = |
| (dvma_vtob(MEM->tx_data[i])) >>16; |
| MEM->tx_head[i].length = 0; |
| MEM->tx_head[i].misc = 0; |
| } |
| |
| for( i = 0; i < RX_RING_SIZE; i++ ) { |
| MEM->rx_head[i].base = dvma_vtob(MEM->rx_data[i]); |
| MEM->rx_head[i].flag = RMD1_OWN_CHIP; |
| MEM->rx_head[i].base_hi = |
| (dvma_vtob(MEM->rx_data[i])) >> 16; |
| MEM->rx_head[i].buf_length = -PKT_BUF_SZ | 0xf000; |
| MEM->rx_head[i].msg_length = 0; |
| } |
| |
| /* tell the card it's ether address, bytes swapped */ |
| MEM->init.hwaddr[0] = dev->dev_addr[1]; |
| MEM->init.hwaddr[1] = dev->dev_addr[0]; |
| MEM->init.hwaddr[2] = dev->dev_addr[3]; |
| MEM->init.hwaddr[3] = dev->dev_addr[2]; |
| MEM->init.hwaddr[4] = dev->dev_addr[5]; |
| MEM->init.hwaddr[5] = dev->dev_addr[4]; |
| |
| MEM->init.mode = 0x0000; |
| MEM->init.filter[0] = 0x00000000; |
| MEM->init.filter[1] = 0x00000000; |
| MEM->init.rdra = dvma_vtob(MEM->rx_head); |
| MEM->init.rlen = (RX_LOG_RING_SIZE << 13) | |
| (dvma_vtob(MEM->rx_head) >> 16); |
| MEM->init.tdra = dvma_vtob(MEM->tx_head); |
| MEM->init.tlen = (TX_LOG_RING_SIZE << 13) | |
| (dvma_vtob(MEM->tx_head) >> 16); |
| |
| |
| /* tell the lance the address of its init block */ |
| REGA(CSR1) = dvma_vtob(&(MEM->init)); |
| REGA(CSR2) = dvma_vtob(&(MEM->init)) >> 16; |
| |
| #ifdef CONFIG_SUN3X |
| REGA(CSR3) = CSR3_BSWP | CSR3_ACON | CSR3_BCON; |
| #else |
| REGA(CSR3) = CSR3_BSWP; |
| #endif |
| |
| } |
| |
| |
| static int lance_start_xmit( struct sk_buff *skb, struct net_device *dev ) |
| { |
| struct lance_private *lp = netdev_priv(dev); |
| int entry, len; |
| struct lance_tx_head *head; |
| unsigned long flags; |
| |
| DPRINTK( 1, ( "%s: transmit start.\n", |
| dev->name)); |
| |
| /* Transmitter timeout, serious problems. */ |
| if (netif_queue_stopped(dev)) { |
| int tickssofar = jiffies - dev->trans_start; |
| if (tickssofar < 20) |
| return( 1 ); |
| |
| DPRINTK( 1, ( "%s: transmit timed out, status %04x, resetting.\n", |
| dev->name, DREG )); |
| DREG = CSR0_STOP; |
| /* |
| * Always set BSWP after a STOP as STOP puts it back into |
| * little endian mode. |
| */ |
| REGA(CSR3) = CSR3_BSWP; |
| dev->stats.tx_errors++; |
| |
| if(lance_debug >= 2) { |
| int i; |
| printk("Ring data: old_tx %d new_tx %d%s new_rx %d\n", |
| lp->old_tx, lp->new_tx, |
| lp->tx_full ? " (full)" : "", |
| lp->new_rx ); |
| for( i = 0 ; i < RX_RING_SIZE; i++ ) |
| printk( "rx #%d: base=%04x blen=%04x mlen=%04x\n", |
| i, MEM->rx_head[i].base, |
| -MEM->rx_head[i].buf_length, |
| MEM->rx_head[i].msg_length); |
| for( i = 0 ; i < TX_RING_SIZE; i++ ) |
| printk("tx #%d: base=%04x len=%04x misc=%04x\n", |
| i, MEM->tx_head[i].base, |
| -MEM->tx_head[i].length, |
| MEM->tx_head[i].misc ); |
| } |
| |
| lance_init_ring(dev); |
| REGA( CSR0 ) = CSR0_INEA | CSR0_INIT | CSR0_STRT; |
| |
| netif_start_queue(dev); |
| dev->trans_start = jiffies; |
| |
| return 0; |
| } |
| |
| |
| /* Block a timer-based transmit from overlapping. This could better be |
| done with atomic_swap(1, dev->tbusy), but set_bit() works as well. */ |
| |
| /* Block a timer-based transmit from overlapping with us by |
| stopping the queue for a bit... */ |
| |
| netif_stop_queue(dev); |
| |
| if (test_and_set_bit( 0, (void*)&lp->lock ) != 0) { |
| printk( "%s: tx queue lock!.\n", dev->name); |
| /* don't clear dev->tbusy flag. */ |
| return 1; |
| } |
| |
| AREG = CSR0; |
| DPRINTK( 2, ( "%s: lance_start_xmit() called, csr0 %4.4x.\n", |
| dev->name, DREG )); |
| |
| #ifdef CONFIG_SUN3X |
| /* this weirdness doesn't appear on sun3... */ |
| if(!(DREG & CSR0_INIT)) { |
| DPRINTK( 1, ("INIT not set, reinitializing...\n")); |
| REGA( CSR0 ) = CSR0_STOP; |
| lance_init_ring(dev); |
| REGA( CSR0 ) = CSR0_INIT | CSR0_STRT; |
| } |
| #endif |
| |
| /* Fill in a Tx ring entry */ |
| #if 0 |
| if (lance_debug >= 2) { |
| printk( "%s: TX pkt %d type 0x%04x" |
| " from %s to %s" |
| " data at 0x%08x len %d\n", |
| dev->name, lp->new_tx, ((u_short *)skb->data)[6], |
| DEV_ADDR(&skb->data[6]), DEV_ADDR(skb->data), |
| (int)skb->data, (int)skb->len ); |
| } |
| #endif |
| /* We're not prepared for the int until the last flags are set/reset. |
| * And the int may happen already after setting the OWN_CHIP... */ |
| local_irq_save(flags); |
| |
| /* Mask to ring buffer boundary. */ |
| entry = lp->new_tx; |
| head = &(MEM->tx_head[entry]); |
| |
| /* Caution: the write order is important here, set the "ownership" bits |
| * last. |
| */ |
| |
| /* the sun3's lance needs it's buffer padded to the minimum |
| size */ |
| len = (ETH_ZLEN < skb->len) ? skb->len : ETH_ZLEN; |
| |
| // head->length = -len; |
| head->length = (-len) | 0xf000; |
| head->misc = 0; |
| |
| skb_copy_from_linear_data(skb, PKTBUF_ADDR(head), skb->len); |
| if (len != skb->len) |
| memset(PKTBUF_ADDR(head) + skb->len, 0, len-skb->len); |
| |
| head->flag = TMD1_OWN_CHIP | TMD1_ENP | TMD1_STP; |
| lp->new_tx = (lp->new_tx + 1) & TX_RING_MOD_MASK; |
| dev->stats.tx_bytes += skb->len; |
| |
| /* Trigger an immediate send poll. */ |
| REGA(CSR0) = CSR0_INEA | CSR0_TDMD | CSR0_STRT; |
| AREG = CSR0; |
| DPRINTK( 2, ( "%s: lance_start_xmit() exiting, csr0 %4.4x.\n", |
| dev->name, DREG )); |
| dev->trans_start = jiffies; |
| dev_kfree_skb( skb ); |
| |
| lp->lock = 0; |
| if ((MEM->tx_head[(entry+1) & TX_RING_MOD_MASK].flag & TMD1_OWN) == |
| TMD1_OWN_HOST) |
| netif_start_queue(dev); |
| |
| local_irq_restore(flags); |
| |
| return 0; |
| } |
| |
| /* The LANCE interrupt handler. */ |
| |
| static irqreturn_t lance_interrupt( int irq, void *dev_id) |
| { |
| struct net_device *dev = dev_id; |
| struct lance_private *lp = netdev_priv(dev); |
| int csr0; |
| static int in_interrupt; |
| |
| if (dev == NULL) { |
| DPRINTK( 1, ( "lance_interrupt(): invalid dev_id\n" )); |
| return IRQ_NONE; |
| } |
| |
| if (in_interrupt) |
| DPRINTK( 2, ( "%s: Re-entering the interrupt handler.\n", dev->name )); |
| in_interrupt = 1; |
| |
| still_more: |
| flush_cache_all(); |
| |
| AREG = CSR0; |
| csr0 = DREG; |
| |
| /* ack interrupts */ |
| DREG = csr0 & (CSR0_TINT | CSR0_RINT | CSR0_IDON); |
| |
| /* clear errors */ |
| if(csr0 & CSR0_ERR) |
| DREG = CSR0_BABL | CSR0_MERR | CSR0_CERR | CSR0_MISS; |
| |
| |
| DPRINTK( 2, ( "%s: interrupt csr0=%04x new csr=%04x.\n", |
| dev->name, csr0, DREG )); |
| |
| if (csr0 & CSR0_TINT) { /* Tx-done interrupt */ |
| int old_tx = lp->old_tx; |
| |
| // if(lance_debug >= 3) { |
| // int i; |
| // |
| // printk("%s: tx int\n", dev->name); |
| // |
| // for(i = 0; i < TX_RING_SIZE; i++) |
| // printk("ring %d flag=%04x\n", i, |
| // MEM->tx_head[i].flag); |
| // } |
| |
| while( old_tx != lp->new_tx) { |
| struct lance_tx_head *head = &(MEM->tx_head[old_tx]); |
| |
| DPRINTK(3, ("on tx_ring %d\n", old_tx)); |
| |
| if (head->flag & TMD1_OWN_CHIP) |
| break; /* It still hasn't been Txed */ |
| |
| if (head->flag & TMD1_ERR) { |
| int status = head->misc; |
| dev->stats.tx_errors++; |
| if (status & TMD3_RTRY) dev->stats.tx_aborted_errors++; |
| if (status & TMD3_LCAR) dev->stats.tx_carrier_errors++; |
| if (status & TMD3_LCOL) dev->stats.tx_window_errors++; |
| if (status & (TMD3_UFLO | TMD3_BUFF)) { |
| dev->stats.tx_fifo_errors++; |
| printk("%s: Tx FIFO error\n", |
| dev->name); |
| REGA(CSR0) = CSR0_STOP; |
| REGA(CSR3) = CSR3_BSWP; |
| lance_init_ring(dev); |
| REGA(CSR0) = CSR0_STRT | CSR0_INEA; |
| return IRQ_HANDLED; |
| } |
| } else if(head->flag & (TMD1_ENP | TMD1_STP)) { |
| |
| head->flag &= ~(TMD1_ENP | TMD1_STP); |
| if(head->flag & (TMD1_ONE | TMD1_MORE)) |
| dev->stats.collisions++; |
| |
| dev->stats.tx_packets++; |
| DPRINTK(3, ("cleared tx ring %d\n", old_tx)); |
| } |
| old_tx = (old_tx +1) & TX_RING_MOD_MASK; |
| } |
| |
| lp->old_tx = old_tx; |
| } |
| |
| |
| if (netif_queue_stopped(dev)) { |
| /* The ring is no longer full, clear tbusy. */ |
| netif_start_queue(dev); |
| netif_wake_queue(dev); |
| } |
| |
| if (csr0 & CSR0_RINT) /* Rx interrupt */ |
| lance_rx( dev ); |
| |
| /* Log misc errors. */ |
| if (csr0 & CSR0_BABL) dev->stats.tx_errors++; /* Tx babble. */ |
| if (csr0 & CSR0_MISS) dev->stats.rx_errors++; /* Missed a Rx frame. */ |
| if (csr0 & CSR0_MERR) { |
| DPRINTK( 1, ( "%s: Bus master arbitration failure (?!?), " |
| "status %04x.\n", dev->name, csr0 )); |
| /* Restart the chip. */ |
| REGA(CSR0) = CSR0_STOP; |
| REGA(CSR3) = CSR3_BSWP; |
| lance_init_ring(dev); |
| REGA(CSR0) = CSR0_STRT | CSR0_INEA; |
| } |
| |
| |
| /* Clear any other interrupt, and set interrupt enable. */ |
| // DREG = CSR0_BABL | CSR0_CERR | CSR0_MISS | CSR0_MERR | |
| // CSR0_IDON | CSR0_INEA; |
| |
| REGA(CSR0) = CSR0_INEA; |
| |
| if(DREG & (CSR0_RINT | CSR0_TINT)) { |
| DPRINTK(2, ("restarting interrupt, csr0=%#04x\n", DREG)); |
| goto still_more; |
| } |
| |
| DPRINTK( 2, ( "%s: exiting interrupt, csr0=%#04x.\n", |
| dev->name, DREG )); |
| in_interrupt = 0; |
| return IRQ_HANDLED; |
| } |
| |
| /* get packet, toss into skbuff */ |
| static int lance_rx( struct net_device *dev ) |
| { |
| struct lance_private *lp = netdev_priv(dev); |
| int entry = lp->new_rx; |
| |
| /* If we own the next entry, it's a new packet. Send it up. */ |
| while( (MEM->rx_head[entry].flag & RMD1_OWN) == RMD1_OWN_HOST ) { |
| struct lance_rx_head *head = &(MEM->rx_head[entry]); |
| int status = head->flag; |
| |
| if (status != (RMD1_ENP|RMD1_STP)) { /* There was an error. */ |
| /* There is a tricky error noted by John Murphy, |
| <murf@perftech.com> to Russ Nelson: Even with |
| full-sized buffers it's possible for a jabber packet to use two |
| buffers, with only the last correctly noting the error. */ |
| if (status & RMD1_ENP) /* Only count a general error at the */ |
| dev->stats.rx_errors++; /* end of a packet.*/ |
| if (status & RMD1_FRAM) dev->stats.rx_frame_errors++; |
| if (status & RMD1_OFLO) dev->stats.rx_over_errors++; |
| if (status & RMD1_CRC) dev->stats.rx_crc_errors++; |
| if (status & RMD1_BUFF) dev->stats.rx_fifo_errors++; |
| head->flag &= (RMD1_ENP|RMD1_STP); |
| } else { |
| /* Malloc up new buffer, compatible with net-3. */ |
| // short pkt_len = head->msg_length;// & 0xfff; |
| short pkt_len = (head->msg_length & 0xfff) - 4; |
| struct sk_buff *skb; |
| |
| if (pkt_len < 60) { |
| printk( "%s: Runt packet!\n", dev->name ); |
| dev->stats.rx_errors++; |
| } |
| else { |
| skb = dev_alloc_skb( pkt_len+2 ); |
| if (skb == NULL) { |
| DPRINTK( 1, ( "%s: Memory squeeze, deferring packet.\n", |
| dev->name )); |
| |
| dev->stats.rx_dropped++; |
| head->msg_length = 0; |
| head->flag |= RMD1_OWN_CHIP; |
| lp->new_rx = (lp->new_rx+1) & |
| RX_RING_MOD_MASK; |
| } |
| |
| #if 0 |
| if (lance_debug >= 3) { |
| u_char *data = PKTBUF_ADDR(head); |
| printk("%s: RX pkt %d type 0x%04x" |
| " from %pM to %pM", |
| dev->name, lp->new_tx, ((u_short *)data)[6], |
| &data[6], data); |
| |
| printk(" data %02x %02x %02x %02x %02x %02x %02x %02x " |
| "len %d at %08x\n", |
| data[15], data[16], data[17], data[18], |
| data[19], data[20], data[21], data[22], |
| pkt_len, data); |
| } |
| #endif |
| if (lance_debug >= 3) { |
| u_char *data = PKTBUF_ADDR(head); |
| printk( "%s: RX pkt %d type 0x%04x len %d\n ", dev->name, entry, ((u_short *)data)[6], pkt_len); |
| } |
| |
| |
| skb_reserve( skb, 2 ); /* 16 byte align */ |
| skb_put( skb, pkt_len ); /* Make room */ |
| skb_copy_to_linear_data(skb, |
| PKTBUF_ADDR(head), |
| pkt_len); |
| |
| skb->protocol = eth_type_trans( skb, dev ); |
| netif_rx( skb ); |
| dev->stats.rx_packets++; |
| dev->stats.rx_bytes += pkt_len; |
| } |
| } |
| |
| // head->buf_length = -PKT_BUF_SZ | 0xf000; |
| head->msg_length = 0; |
| head->flag = RMD1_OWN_CHIP; |
| |
| entry = lp->new_rx = (lp->new_rx +1) & RX_RING_MOD_MASK; |
| } |
| |
| /* From lance.c (Donald Becker): */ |
| /* We should check that at least two ring entries are free. |
| If not, we should free one and mark stats->rx_dropped++. */ |
| |
| return 0; |
| } |
| |
| |
| static int lance_close( struct net_device *dev ) |
| { |
| struct lance_private *lp = netdev_priv(dev); |
| |
| netif_stop_queue(dev); |
| |
| AREG = CSR0; |
| |
| DPRINTK( 2, ( "%s: Shutting down ethercard, status was %2.2x.\n", |
| dev->name, DREG )); |
| |
| /* We stop the LANCE here -- it occasionally polls |
| memory if we don't. */ |
| DREG = CSR0_STOP; |
| return 0; |
| } |
| |
| |
| /* Set or clear the multicast filter for this adaptor. |
| num_addrs == -1 Promiscuous mode, receive all packets |
| num_addrs == 0 Normal mode, clear multicast list |
| num_addrs > 0 Multicast mode, receive normal and MC packets, and do |
| best-effort filtering. |
| */ |
| |
| /* completely untested on a sun3 */ |
| static void set_multicast_list( struct net_device *dev ) |
| { |
| struct lance_private *lp = netdev_priv(dev); |
| |
| if(netif_queue_stopped(dev)) |
| /* Only possible if board is already started */ |
| return; |
| |
| /* We take the simple way out and always enable promiscuous mode. */ |
| DREG = CSR0_STOP; /* Temporarily stop the lance. */ |
| |
| if (dev->flags & IFF_PROMISC) { |
| /* Log any net taps. */ |
| DPRINTK( 3, ( "%s: Promiscuous mode enabled.\n", dev->name )); |
| REGA( CSR15 ) = 0x8000; /* Set promiscuous mode */ |
| } else { |
| short multicast_table[4]; |
| int num_addrs = dev->mc_count; |
| int i; |
| /* We don't use the multicast table, but rely on upper-layer |
| * filtering. */ |
| memset( multicast_table, (num_addrs == 0) ? 0 : -1, |
| sizeof(multicast_table) ); |
| for( i = 0; i < 4; i++ ) |
| REGA( CSR8+i ) = multicast_table[i]; |
| REGA( CSR15 ) = 0; /* Unset promiscuous mode */ |
| } |
| |
| /* |
| * Always set BSWP after a STOP as STOP puts it back into |
| * little endian mode. |
| */ |
| REGA( CSR3 ) = CSR3_BSWP; |
| |
| /* Resume normal operation and reset AREG to CSR0 */ |
| REGA( CSR0 ) = CSR0_IDON | CSR0_INEA | CSR0_STRT; |
| } |
| |
| |
| #ifdef MODULE |
| |
| static struct net_device *sun3lance_dev; |
| |
| int __init init_module(void) |
| { |
| sun3lance_dev = sun3lance_probe(-1); |
| if (IS_ERR(sun3lance_dev)) |
| return PTR_ERR(sun3lance_dev); |
| return 0; |
| } |
| |
| void __exit cleanup_module(void) |
| { |
| unregister_netdev(sun3lance_dev); |
| #ifdef CONFIG_SUN3 |
| iounmap((void __iomem *)sun3lance_dev->base_addr); |
| #endif |
| free_netdev(sun3lance_dev); |
| } |
| |
| #endif /* MODULE */ |
| |