diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt
index 313dabd..faa4b44 100644
--- a/Documentation/devicetree/bindings/arm/arm,scpi.txt
+++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt
@@ -87,10 +87,33 @@
 			 implementation for the IDs to use. For Juno
 			 R0 and Juno R1 refer to [3].
 
+Power domain bindings for the power domains based on SCPI Message Protocol
+------------------------------------------------------------
+
+This binding uses the generic power domain binding[4].
+
+PM domain providers
+===================
+
+Required properties:
+ - #power-domain-cells : Should be 1. Contains the device or the power
+			 domain ID value used by SCPI commands.
+ - num-domains: Total number of power domains provided by SCPI. This is
+		needed as the SCPI message protocol lacks a mechanism to
+		query this information at runtime.
+
+PM domain consumers
+===================
+
+Required properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+
 [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/thermal/thermal.txt
 [3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html
+[4] Documentation/devicetree/bindings/power/power_domain.txt
 
 Example:
 
@@ -144,6 +167,12 @@
 		compatible = "arm,scpi-sensors";
 		#thermal-sensor-cells = <1>;
 	};
+
+	scpi_devpd: scpi-power-domains {
+		compatible = "arm,scpi-power-domains";
+		num-domains = <2>;
+		#power-domain-cells = <1>;
+	};
 };
 
 cpu@0 {
@@ -156,6 +185,7 @@
 	...
 	reg = <0 0x7ff60000 0 0x1000>;
 	clocks = <&scpi_clk 4>;
+	power-domains = <&scpi_devpd 1>;
 };
 
 thermal-zones {
@@ -186,3 +216,7 @@
 temperature sensor provided by SCP firmware to setup a thermal
 zone. The ID "3" is the sensor identifier for the temperature sensor
 as used by the firmware.
+
+The num-domains property in scpi-power-domains domain specifies that
+SCPI provides 2 power domains. The hdlcd node uses the power domain with
+domain ID 1.
diff --git a/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt
new file mode 100644
index 0000000..7ff13be
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt
@@ -0,0 +1,45 @@
+NVIDIA Tegra ACONNECT Bus
+
+The Tegra ACONNECT bus is an AXI switch which is used to connnect various
+components inside the Audio Processing Engine (APE). All CPU accesses to
+the APE subsystem go through the ACONNECT via an APB to AXI wrapper.
+
+Required properties:
+- compatible: Must be "nvidia,tegra210-aconnect".
+- clocks: Must contain the entries for the APE clock (TEGRA210_CLK_APE),
+  and APE interface clock (TEGRA210_CLK_APB2APE).
+- clock-names: Must contain the names "ape" and "apb2ape" for the corresponding
+  'clocks' entries.
+- power-domains: Must contain a phandle that points to the audio powergate
+  (namely 'aud') for Tegra210.
+- #address-cells: The number of cells used to represent physical base addresses
+  in the aconnect address space. Should be 1.
+- #size-cells: The number of cells used to represent the size of an address
+  range in the aconnect address space. Should be 1.
+- ranges: Mapping of the aconnect address space to the CPU address space.
+
+All devices accessed via the ACONNNECT are described by child-nodes.
+
+Example:
+
+	aconnect@702c0000 {
+		compatible = "nvidia,tegra210-aconnect";
+		clocks = <&tegra_car TEGRA210_CLK_APE>,
+			 <&tegra_car TEGRA210_CLK_APB2APE>;
+		clock-names = "ape", "apb2ape";
+		power-domains = <&pd_audio>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x702c0000 0x0 0x702c0000 0x00040000>;
+
+		status = "disabled";
+
+		child1 {
+			...
+		};
+
+		child2 {
+			...
+		};
+	};
diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt
index ce5a747..f1bd53f 100644
--- a/Documentation/devicetree/bindings/clock/clps711x-clock.txt
+++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt
@@ -1,7 +1,7 @@
 * Clock bindings for the Cirrus Logic CLPS711X CPUs
 
 Required properties:
-- compatible       : Shall contain "cirrus,clps711x-clk".
+- compatible       : Shall contain "cirrus,ep7209-clk".
 - reg              : Address of the internal register set.
 - startup-frequency: Factory set CPU startup frequency in HZ.
 - #clock-cells     : Should be <1>.
@@ -13,7 +13,7 @@
 Example:
 	clks: clks@80000000 {
 		#clock-cells = <1>;
-		compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk";
+		compatible = "cirrus,ep7312-clk", "cirrus,ep7209-clk";
 		reg = <0x80000000 0xc000>;
 		startup-frequency = <73728000>;
 	};
diff --git a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt
index d685be8..e9c6574 100644
--- a/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt
+++ b/Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt
@@ -1,7 +1,7 @@
 * Currus Logic CLPS711X Framebuffer
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-fb".
+- compatible: Shall contain "cirrus,ep7209-fb".
 - reg       : Physical base address and length of the controller's registers +
               location and size of the framebuffer memory.
 - clocks    : phandle + clock specifier pair of the FB reference clock.
@@ -18,7 +18,7 @@
 
 Example:
 	fb: fb@800002c0 {
-		compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb";
+		compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb";
 		reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
 		clocks = <&clks 2>;
 		lcd-supply = <&reg5v0>;
diff --git a/Documentation/devicetree/bindings/input/clps711x-keypad.txt b/Documentation/devicetree/bindings/input/clps711x-keypad.txt
index e68d2bb..3eed881 100644
--- a/Documentation/devicetree/bindings/input/clps711x-keypad.txt
+++ b/Documentation/devicetree/bindings/input/clps711x-keypad.txt
@@ -1,7 +1,7 @@
 * Cirrus Logic CLPS711X matrix keypad device tree bindings
 
 Required Properties:
-- compatible:    Shall contain "cirrus,clps711x-keypad".
+- compatible:    Shall contain "cirrus,ep7209-keypad".
 - row-gpios:     List of GPIOs used as row lines.
 - poll-interval: Poll interval time in milliseconds.
 - linux,keymap:  The definition can be found at
@@ -12,7 +12,7 @@
 
 Example:
 	keypad {
-		compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad";
+		compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad";
 		autorepeat;
 		poll-interval = <120>;
 		row-gpios = <&porta 0 0>,
diff --git a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt
index 759339c..969b458 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt
@@ -2,7 +2,7 @@
 
 Required properties:
 
-- compatible: Should be "cirrus,clps711x-intc".
+- compatible: Should be "cirrus,ep7209-intc".
 - reg: Specifies base physical address of the registers set.
 - interrupt-controller: Identifies the node as an interrupt controller.
 - #interrupt-cells: Specifies the number of cells needed to encode an
@@ -34,7 +34,7 @@
 
 Example:
 	intc: interrupt-controller {
-		compatible = "cirrus,clps711x-intc";
+		compatible = "cirrus,ep7312-intc", "cirrus,ep7209-intc";
 		reg = <0x80000000 0x4000>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt
index 2d5787e..92c94f5 100644
--- a/Documentation/devicetree/bindings/media/s5p-mfc.txt
+++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt
@@ -21,15 +21,18 @@
   - clock-names : from common clock binding: must contain "mfc",
 		  corresponding to entry in the clocks property.
 
-  - samsung,mfc-r : Base address of the first memory bank used by MFC
-		    for DMA contiguous memory allocation and its size.
-
-  - samsung,mfc-l : Base address of the second memory bank used by MFC
-		    for DMA contiguous memory allocation and its size.
-
 Optional properties:
   - power-domains : power-domain property defined with a phandle
 			   to respective power domain.
+  - memory-region : from reserved memory binding: phandles to two reserved
+	memory regions, first is for "left" mfc memory bus interfaces,
+	second if for the "right" mfc memory bus, used when no SYSMMU
+	support is available
+
+Obsolete properties:
+  - samsung,mfc-r, samsung,mfc-l : support removed, please use memory-region
+	property instead
+
 
 Example:
 SoC specific DT entry:
@@ -43,9 +46,29 @@
 	clock-names = "mfc";
 };
 
+Reserved memory specific DT entry for given board (see reserved memory binding
+for more information):
+
+reserved-memory {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	mfc_left: region@51000000 {
+		compatible = "shared-dma-pool";
+		no-map;
+		reg = <0x51000000 0x800000>;
+	};
+
+	mfc_right: region@43000000 {
+		compatible = "shared-dma-pool";
+		no-map;
+		reg = <0x43000000 0x800000>;
+	};
+};
+
 Board specific DT entry:
 
 codec@13400000 {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
diff --git a/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt
new file mode 100644
index 0000000..9bb5f57
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt
@@ -0,0 +1,136 @@
+* Device tree bindings for Atmel EBI
+
+The External Bus Interface (EBI) controller is a bus where you can connect
+asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
+The EBI provides a glue-less interface to asynchronous memories through the SMC
+(Static Memory Controller).
+
+Required properties:
+
+- compatible:		"atmel,at91sam9260-ebi"
+			"atmel,at91sam9261-ebi"
+			"atmel,at91sam9263-ebi0"
+			"atmel,at91sam9263-ebi1"
+			"atmel,at91sam9rl-ebi"
+			"atmel,at91sam9g45-ebi"
+			"atmel,at91sam9x5-ebi"
+			"atmel,sama5d3-ebi"
+
+- reg:			Contains offset/length value for EBI memory mapping.
+			This property might contain several entries if the EBI
+			memory range is not contiguous
+
+- #address-cells:	Must be 2.
+			The first cell encodes the CS.
+			The second cell encode the offset into the CS memory
+			range.
+
+- #size-cells:		Must be set to 1.
+
+- ranges:		Encodes CS to memory region association.
+
+- clocks:		Clock feeding the EBI controller.
+			See clock-bindings.txt
+
+Children device nodes are representing device connected to the EBI bus.
+
+Required device node properties:
+
+- reg:			Contains the chip-select id, the offset and the length
+			of the memory region requested by the device.
+
+EBI bus configuration will be defined directly in the device subnode.
+
+Optional EBI/SMC properties:
+
+- atmel,smc-bus-width:		width of the asynchronous device's data bus
+				8, 16 or 32.
+				Default to 8 when undefined.
+
+- atmel,smc-byte-access-type	"write" or "select" (see Atmel datasheet).
+				Default to "select" when undefined.
+
+- atmel,smc-read-mode		"nrd" or "ncs".
+				Default to "ncs" when undefined.
+
+- atmel,smc-write-mode		"nwe" or "ncs".
+				Default to "ncs" when undefined.
+
+- atmel,smc-exnw-mode		"disabled", "frozen" or "ready".
+				Default to "disabled" when undefined.
+
+- atmel,smc-page-mode		enable page mode if present. The provided value
+				defines the page size (supported values: 4, 8,
+				16 and 32).
+
+- atmel,smc-tdf-mode:		"normal" or "optimized". When set to
+				"optimized" the data float time is optimized
+				depending on the next device being accessed
+				(next device setup time is subtracted to the
+				current device data float time).
+				Default to "normal" when undefined.
+
+If at least one atmel,smc- property is defined the following SMC timing
+properties become mandatory. In the other hand, if none of the atmel,smc-
+properties are specified, we assume that the EBI bus configuration will be
+handled by the sub-device driver, and none of those properties should be
+defined.
+
+All the timings are expressed in nanoseconds (see Atmel datasheet for a full
+description).
+
+- atmel,smc-ncs-rd-setup-ns
+- atmel,smc-nrd-setup-ns
+- atmel,smc-ncs-wr-setup-ns
+- atmel,smc-nwe-setup-ns
+- atmel,smc-ncs-rd-pulse-ns
+- atmel,smc-nrd-pulse-ns
+- atmel,smc-ncs-wr-pulse-ns
+- atmel,smc-nwe-pulse-ns
+- atmel,smc-nwe-cycle-ns
+- atmel,smc-nrd-cycle-ns
+- atmel,smc-tdf-ns
+
+Example:
+
+	ebi: ebi@10000000 {
+		compatible = "atmel,sama5d3-ebi";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		atmel,smc = <&hsmc>;
+		atmel,matrix = <&matrix>;
+		reg = <0x10000000 0x10000000
+		       0x40000000 0x30000000>;
+		ranges = <0x0 0x0 0x10000000 0x10000000
+			  0x1 0x0 0x40000000 0x10000000
+			  0x2 0x0 0x50000000 0x10000000
+			  0x3 0x0 0x60000000 0x10000000>;
+		clocks = <&mck>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ebi_addr>;
+
+		nor: flash@0,0 {
+			compatible = "cfi-flash";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x0 0x0 0x1000000>;
+			bank-width = <2>;
+
+			atmel,smc-read-mode = "nrd";
+			atmel,smc-write-mode = "nwe";
+			atmel,smc-bus-width = <16>;
+			atmel,smc-ncs-rd-setup-ns = <0>;
+			atmel,smc-ncs-wr-setup-ns = <0>;
+			atmel,smc-nwe-setup-ns = <8>;
+			atmel,smc-nrd-setup-ns = <16>;
+			atmel,smc-ncs-rd-pulse-ns = <84>;
+			atmel,smc-ncs-wr-pulse-ns = <84>;
+			atmel,smc-nrd-pulse-ns = <76>;
+			atmel,smc-nwe-pulse-ns = <76>;
+			atmel,smc-nrd-cycle-ns = <107>;
+			atmel,smc-nwe-cycle-ns = <84>;
+			atmel,smc-tdf-ns = <16>;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
index b74e4d4..0725fb3 100644
--- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
+++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
@@ -14,6 +14,7 @@
       - "renesas,r8a7793-sysc" (R-Car M2-N)
       - "renesas,r8a7794-sysc" (R-Car E2)
       - "renesas,r8a7795-sysc" (R-Car H3)
+      - "renesas,r8a7796-sysc" (R-Car M3-W)
   - reg: Address start and address range for the device.
   - #power-domain-cells: Must be 1.
 
diff --git a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt
index a183db4..c0b2028 100644
--- a/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt
+++ b/Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt
@@ -1,15 +1,14 @@
 * Cirris Logic CLPS711X PWM controller
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-pwm".
+- compatible: Shall contain "cirrus,ep7209-pwm".
 - reg: Physical base address and length of the controller's registers.
 - clocks: phandle + clock specifier pair of the PWM reference clock.
 - #pwm-cells: Should be 1. The cell specifies the index of the channel.
 
 Example:
 	pwm: pwm@80000400 {
-		compatible = "cirrus,ep7312-pwm",
-			     "cirrus,clps711x-pwm";
+		compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm";
 		reg = <0x80000400 0x4>;
 		clocks = <&clks 8>;
 		#pwm-cells = <1>;
diff --git a/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt
new file mode 100644
index 0000000..e746b63
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt
@@ -0,0 +1,18 @@
+Amlogic Meson SoC Reset Controller
+=======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "amlogic,meson8b-reset" or "amlogic,meson-gxbb-reset"
+- reg: should contain the register address base
+- #reset-cells: 1, see below
+
+example:
+
+reset: reset-controller {
+	compatible = "amlogic,meson-gxbb-reset";
+	reg = <0x0 0x04404 0x0 0x20>;
+	#reset-cells = <1>;
+};
diff --git a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
index e0b185a..c25da39 100644
--- a/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
+++ b/Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt
@@ -8,7 +8,9 @@
 hi6220 SoC.
 
 Required properties:
-- compatible: may be "hisilicon,hi6220-sysctrl"
+- compatible: should be one of the following:
+  - "hisilicon,hi6220-sysctrl", "syscon" : For peripheral reset controller.
+  - "hisilicon,hi6220-mediactrl", "syscon" : For media reset controller.
 - reg: should be register base and length as documented in the
   datasheet
 - #reset-cells: 1, see below
diff --git a/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
new file mode 100644
index 0000000..164c7f3
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/ti-syscon-reset.txt
@@ -0,0 +1,91 @@
+TI SysCon Reset Controller
+=======================
+
+Almost all SoCs have hardware modules that require reset control in addition
+to clock and power control for their functionality. The reset control is
+typically provided by means of memory-mapped I/O registers. These registers are
+sometimes a part of a larger register space region implementing various
+functionalities. This register range is best represented as a syscon node to
+allow multiple entities to access their relevant registers in the common
+register space.
+
+A SysCon Reset Controller node defines a device that uses a syscon node
+and provides reset management functionality for various hardware modules
+present on the SoC.
+
+SysCon Reset Controller Node
+============================
+Each of the reset provider/controller nodes should be a child of a syscon
+node and have the following properties.
+
+Required properties:
+--------------------
+ - compatible		: Should be,
+			    "ti,k2e-pscrst"
+			    "ti,k2l-pscrst"
+			    "ti,k2hk-pscrst"
+			    "ti,syscon-reset"
+ - #reset-cells		: Should be 1. Please see the reset consumer node below
+			  for usage details
+ - ti,reset-bits	: Contains the reset control register information
+			  Should contain 7 cells for each reset exposed to
+			  consumers, defined as:
+			    Cell #1 : offset of the reset assert control
+			              register from the syscon register base
+			    Cell #2 : bit position of the reset in the reset
+			              assert control register
+			    Cell #3 : offset of the reset deassert control
+			              register from the syscon register base
+			    Cell #4 : bit position of the reset in the reset
+			              deassert control register
+			    Cell #5 : offset of the reset status register
+			              from the syscon register base
+			    Cell #6 : bit position of the reset in the
+			              reset status register
+			    Cell #7 : Flags used to control reset behavior,
+			              availible flags defined in the DT include
+			              file <dt-bindings/reset/ti-syscon.h>
+
+SysCon Reset Consumer Nodes
+===========================
+Each of the reset consumer nodes should have the following properties,
+in addition to their own properties.
+
+Required properties:
+--------------------
+ - resets	: A phandle to the reset controller node and an index number
+		  to a reset specifier as defined above.
+
+Please also refer to Documentation/devicetree/bindings/reset/reset.txt for
+common reset controller usage by consumers.
+
+Example:
+--------
+The following example demonstrates a syscon node, the reset controller node
+using the syscon node, and a consumer (a DSP device) on the TI Keystone 2
+Edison SoC.
+
+/ {
+	soc {
+		psc: power-sleep-controller@02350000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x02350000 0x1000>;
+
+			pscrst: psc-reset {
+				compatible = "ti,k2e-pscrst", "ti,syscon-reset";
+				#reset-cells = <1>;
+
+				ti,reset-bits = <
+					0xa3c 8 0xa3c 8 0x83c 8 (ASSERT_SET|DEASSERT_CLEAR|STATUS_SET)   /* 0: pcrst-dsp0 */
+					0xa40 5 0xa44 3 0     0 (ASSERT_SET|DEASSERT_CLEAR|STATUS_NONE)  /* 1: pcrst-example */
+				>;
+			};
+		};
+
+		dsp0: dsp0 {
+			...
+			resets = <&pscrst 0>;
+			...
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt
index caaeb25..07013fa 100644
--- a/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt
+++ b/Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt
@@ -1,7 +1,7 @@
 * Cirrus Logic CLPS711X Universal Asynchronous Receiver/Transmitter (UART)
 
 Required properties:
-- compatible: Should be "cirrus,clps711x-uart".
+- compatible: Should be "cirrus,ep7209-uart".
 - reg: Address and length of the register set for the device.
 - interrupts: Should contain UART TX and RX interrupt.
 - clocks: Should contain UART core clock number.
@@ -20,7 +20,7 @@
 	};
 
 	uart1: uart@80000480 {
-		compatible = "cirrus,clps711x-uart";
+		compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart";
 		reg = <0x80000480 0x80>;
 		interrupts = <12 13>;
 		clocks = <&clks 11>;
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt
index 5cc82b8..af9ca37 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt
@@ -68,7 +68,7 @@
 	Value type: <u32>
 	Definition: must be 2 - denoting the bit in the entry and IRQ flags
 
-- #qcom,state-cells:
+- #qcom,smem-state-cells:
 	Usage: required for outgoing entries
 	Value type: <u32>
 	Definition: must be 1 - denoting the bit in the entry
@@ -92,7 +92,7 @@
 	wcnss_smp2p_out: master-kernel {
 		qcom,entry-name = "master-kernel";
 
-		#qcom,state-cells = <1>;
+		#qcom,smem-state-cells = <1>;
 	};
 
 	wcnss_smp2p_in: slave-kernel {
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt
index a6634c7..2993b5a 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt
@@ -51,7 +51,7 @@
 	Definition: specifies the offset, in words, of the first bit for this
 		    entry
 
-- #qcom,state-cells:
+- #qcom,smem-state-cells:
 	Usage: required for local entry
 	Value type: <u32>
 	Definition: must be 1 - denotes bit number
@@ -91,7 +91,7 @@
 	apps_smsm: apps@0 {
 		reg = <0>;
 
-		#qcom,state-cells = <1>;
+		#qcom,smem-state-cells = <1>;
 	};
 
 	wcnss_smsm: wcnss@7 {
diff --git a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt
index cd55b52..d4c62e7 100644
--- a/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt
+++ b/Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt
@@ -1,7 +1,7 @@
 * Cirrus Logic CLPS711X Timer Counter
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-timer".
+- compatible: Shall contain "cirrus,ep7209-timer".
 - reg       : Address and length of the register set.
 - interrupts: The interrupt number of the timer.
 - clocks    : phandle of timer reference clock.
@@ -15,14 +15,14 @@
 	};
 
 	timer1: timer@80000300 {
-		compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer";
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
 		reg = <0x80000300 0x4>;
 		interrupts = <8>;
 		clocks = <&clks 5>;
 	};
 
 	timer2: timer@80000340 {
-		compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer";
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
 		reg = <0x80000340 0x4>;
 		interrupts = <9>;
 		clocks = <&clks 6>;
diff --git a/Documentation/driver-model/devres.txt b/Documentation/driver-model/devres.txt
index c63eea0..f5e5223 100644
--- a/Documentation/driver-model/devres.txt
+++ b/Documentation/driver-model/devres.txt
@@ -352,6 +352,10 @@
   devm_regulator_put()
   devm_regulator_register()
 
+RESET
+  devm_reset_control_get()
+  devm_reset_controller_register()
+
 SLAVE DMA ENGINE
   devm_acpi_dma_controller_register()
 
diff --git a/MAINTAINERS b/MAINTAINERS
index 7304d2e..d5c45bc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1521,6 +1521,7 @@
 L:	linux-arm-msm@vger.kernel.org
 L:	linux-soc@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/soc/qcom/
 F:	arch/arm/boot/dts/qcom-*.dts
 F:	arch/arm/boot/dts/qcom-*.dtsi
 F:	arch/arm/mach-qcom/
@@ -2489,6 +2490,7 @@
 F:	arch/arm/configs/bcm_defconfig
 F:	drivers/mmc/host/sdhci-bcm-kona.c
 F:	drivers/clocksource/bcm_kona_timer.c
+F:	drivers/power/reset/brcm-kona-reset.c
 
 BROADCOM BCM2835 ARM ARCHITECTURE
 M:	Stephen Warren <swarren@wwwdotorg.org>
diff --git a/arch/arm/boot/dts/exynos-mfc-reserved-memory.dtsi b/arch/arm/boot/dts/exynos-mfc-reserved-memory.dtsi
new file mode 100644
index 0000000..c4d063a
--- /dev/null
+++ b/arch/arm/boot/dts/exynos-mfc-reserved-memory.dtsi
@@ -0,0 +1,29 @@
+/*
+ * Samsung's Exynos SoC MFC (Video Codec) reserved memory common definition.
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mfc_left: region@51000000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x51000000 0x800000>;
+		};
+
+		mfc_right: region@43000000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x43000000 0x800000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index ad7394c..f5e4eb2 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -18,6 +18,7 @@
 #include "exynos4210.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4210";
@@ -288,8 +289,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts
index 94ca7d3..de917f0 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -17,6 +17,7 @@
 /dts-v1/;
 #include "exynos4210.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Samsung smdkv310 evaluation board based on Exynos4210";
@@ -133,8 +134,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index ec7619a..276ac9a 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -13,6 +13,7 @@
 #include "exynos4412.dtsi"
 #include "exynos4412-ppmu-common.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	chosen {
@@ -499,6 +500,11 @@
 	clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
 };
 
+&mfc {
+	memory-region = <&mfc_left>, <&mfc_right>;
+	status = "okay";
+};
+
 &mixer {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
index 8bca699..cd363d7 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/exynos4412-origen.dts
@@ -16,6 +16,7 @@
 #include "exynos4412.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4412";
@@ -466,8 +467,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/exynos4412-smdk4412.dts b/arch/arm/boot/dts/exynos4412-smdk4412.dts
index a51069f..9b6d561 100644
--- a/arch/arm/boot/dts/exynos4412-smdk4412.dts
+++ b/arch/arm/boot/dts/exynos4412-smdk4412.dts
@@ -14,6 +14,7 @@
 
 /dts-v1/;
 #include "exynos4412.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Samsung SMDK evaluation board based on Exynos4412";
@@ -112,8 +113,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 85dad29..39940f4 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -14,6 +14,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include "exynos5250.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Arndale evaluation board based on EXYNOS5250";
@@ -516,8 +517,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index b7992b1..9fac874 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -13,6 +13,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "exynos5250.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "SAMSUNG SMDK5250 board based on EXYNOS5250";
@@ -344,8 +345,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
index ac291f5..784130b 100644
--- a/arch/arm/boot/dts/exynos5250-spring.dts
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -14,6 +14,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include "exynos5250.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Google Spring";
@@ -425,8 +426,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index 60bc861..b8b5f3a 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -16,6 +16,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/clock/samsung,s2mps11.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Arndale Octa evaluation board based on EXYNOS5420";
@@ -347,8 +348,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index f9d2e4f..d530b4f 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -16,6 +16,7 @@
 #include <dt-bindings/regulator/maxim,max77802.h>
 #include "exynos5420.dtsi"
 #include "exynos5420-cpus.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Google Peach Pit Rev 6+";
@@ -695,8 +696,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index 2e748d1..5206f41 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -13,6 +13,7 @@
 #include "exynos5420.dtsi"
 #include "exynos5420-cpus.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Samsung SMDK5420 board based on EXYNOS5420";
@@ -355,8 +356,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
index 2a4e10b..7c2335f 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -17,6 +17,7 @@
 #include "exynos5800.dtsi"
 #include "exynos5422-cpus.dtsi"
 #include "exynos5422-cpu-thermal.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	memory {
@@ -406,8 +407,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index 62ceb89..1f73596 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -16,6 +16,7 @@
 #include <dt-bindings/regulator/maxim,max77802.h>
 #include "exynos5800.dtsi"
 #include "exynos5420-cpus.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Google Peach Pi Rev 10+";
@@ -670,8 +671,7 @@
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index e65aa7d..58b334f 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -19,6 +19,7 @@
 	select EXYNOS_THERMAL
 	select EXYNOS_PMU
 	select EXYNOS_SROM
+	select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
 	select HAVE_ARM_SCU if SMP
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG
diff --git a/arch/arm/mach-exynos/Makefile b/arch/arm/mach-exynos/Makefile
index 34d29df..9ea6c546 100644
--- a/arch/arm/mach-exynos/Makefile
+++ b/arch/arm/mach-exynos/Makefile
@@ -13,7 +13,6 @@
 
 obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm.o sleep.o
 obj-$(CONFIG_PM_SLEEP)		+= suspend.o
-obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o
 
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 
@@ -23,5 +22,3 @@
 
 obj-$(CONFIG_EXYNOS5420_MCPM)	+= mcpm-exynos.o
 CFLAGS_mcpm-exynos.o		+= -march=armv7-a
-
-obj-$(CONFIG_S5P_DEV_MFC)	+= s5p-dev-mfc.o
diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c
index 52ccf24..a8620c6 100644
--- a/arch/arm/mach-exynos/exynos.c
+++ b/arch/arm/mach-exynos/exynos.c
@@ -27,7 +27,6 @@
 #include <mach/map.h>
 
 #include "common.h"
-#include "mfc.h"
 
 static struct map_desc exynos4_iodesc[] __initdata = {
 	{
@@ -237,23 +236,6 @@
 	NULL
 };
 
-static void __init exynos_reserve(void)
-{
-#ifdef CONFIG_S5P_DEV_MFC
-	int i;
-	char *mfc_mem[] = {
-		"samsung,mfc-v5",
-		"samsung,mfc-v6",
-		"samsung,mfc-v7",
-		"samsung,mfc-v8",
-	};
-
-	for (i = 0; i < ARRAY_SIZE(mfc_mem); i++)
-		if (of_scan_flat_dt(s5p_fdt_alloc_mfc_mem, mfc_mem[i]))
-			break;
-#endif
-}
-
 static void __init exynos_dt_fixup(void)
 {
 	/*
@@ -275,6 +257,5 @@
 	.init_machine	= exynos_dt_machine_init,
 	.init_late	= exynos_init_late,
 	.dt_compat	= exynos_dt_compat,
-	.reserve	= exynos_reserve,
 	.dt_fixup	= exynos_dt_fixup,
 MACHINE_END
diff --git a/arch/arm/mach-exynos/mfc.h b/arch/arm/mach-exynos/mfc.h
deleted file mode 100644
index dec93cd..0000000
--- a/arch/arm/mach-exynos/mfc.h
+++ /dev/null
@@ -1,16 +0,0 @@
-/*
- * Copyright (C) 2013 Samsung Electronics Co.Ltd
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- */
-
-#ifndef __MACH_EXYNOS_MFC_H
-#define __MACH_EXYNOS_MFC_H __FILE__
-
-int __init s5p_fdt_alloc_mfc_mem(unsigned long node, const char *uname,
-				int depth, void *data);
-
-#endif /* __MACH_EXYNOS_MFC_H */
diff --git a/arch/arm/mach-exynos/s5p-dev-mfc.c b/arch/arm/mach-exynos/s5p-dev-mfc.c
deleted file mode 100644
index 8ef1f3e..0000000
--- a/arch/arm/mach-exynos/s5p-dev-mfc.c
+++ /dev/null
@@ -1,93 +0,0 @@
-/*
- * Copyright (C) 2010-2011 Samsung Electronics Co.Ltd
- *
- * Base S5P MFC resource and device definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/memblock.h>
-#include <linux/ioport.h>
-#include <linux/of_fdt.h>
-#include <linux/of.h>
-
-static struct platform_device s5p_device_mfc_l;
-static struct platform_device s5p_device_mfc_r;
-
-struct s5p_mfc_dt_meminfo {
-	unsigned long	loff;
-	unsigned long	lsize;
-	unsigned long	roff;
-	unsigned long	rsize;
-	char		*compatible;
-};
-
-struct s5p_mfc_reserved_mem {
-	phys_addr_t	base;
-	unsigned long	size;
-	struct device	*dev;
-};
-
-static struct s5p_mfc_reserved_mem s5p_mfc_mem[2] __initdata;
-
-
-static void __init s5p_mfc_reserve_mem(phys_addr_t rbase, unsigned int rsize,
-				phys_addr_t lbase, unsigned int lsize)
-{
-	int i;
-
-	s5p_mfc_mem[0].dev = &s5p_device_mfc_r.dev;
-	s5p_mfc_mem[0].base = rbase;
-	s5p_mfc_mem[0].size = rsize;
-
-	s5p_mfc_mem[1].dev = &s5p_device_mfc_l.dev;
-	s5p_mfc_mem[1].base = lbase;
-	s5p_mfc_mem[1].size = lsize;
-
-	for (i = 0; i < ARRAY_SIZE(s5p_mfc_mem); i++) {
-		struct s5p_mfc_reserved_mem *area = &s5p_mfc_mem[i];
-		if (memblock_remove(area->base, area->size)) {
-			printk(KERN_ERR "Failed to reserve memory for MFC device (%ld bytes at 0x%08lx)\n",
-			       area->size, (unsigned long) area->base);
-			area->base = 0;
-		}
-	}
-}
-
-int __init s5p_fdt_alloc_mfc_mem(unsigned long node, const char *uname,
-				int depth, void *data)
-{
-	const __be32 *prop;
-	int len;
-	struct s5p_mfc_dt_meminfo mfc_mem;
-
-	if (!data)
-		return 0;
-
-	if (!of_flat_dt_is_compatible(node, data))
-		return 0;
-
-	prop = of_get_flat_dt_prop(node, "samsung,mfc-l", &len);
-	if (!prop || (len != 2 * sizeof(unsigned long)))
-		return 0;
-
-	mfc_mem.loff = be32_to_cpu(prop[0]);
-	mfc_mem.lsize = be32_to_cpu(prop[1]);
-
-	prop = of_get_flat_dt_prop(node, "samsung,mfc-r", &len);
-	if (!prop || (len != 2 * sizeof(unsigned long)))
-		return 0;
-
-	mfc_mem.roff = be32_to_cpu(prop[0]);
-	mfc_mem.rsize = be32_to_cpu(prop[1]);
-
-	s5p_mfc_reserve_mem(mfc_mem.roff, mfc_mem.rsize,
-			mfc_mem.loff, mfc_mem.lsize);
-
-	return 1;
-}
diff --git a/arch/arm/mach-shmobile/pm-r8a7779.c b/arch/arm/mach-shmobile/pm-r8a7779.c
index 4174cbc..5c9a93f 100644
--- a/arch/arm/mach-shmobile/pm-r8a7779.c
+++ b/arch/arm/mach-shmobile/pm-r8a7779.c
@@ -23,11 +23,7 @@
 
 static void __init r8a7779_sysc_init(void)
 {
-	void __iomem *base = rcar_sysc_init(0xffd85000);
-
-	/* enable all interrupt sources, but do not use interrupt handler */
-	iowrite32(0x0131000e, base + SYSCIER);
-	iowrite32(0, base + SYSCIMR);
+	rcar_sysc_init(0xffd85000, 0x0131000e);
 }
 
 #else /* CONFIG_PM || CONFIG_SMP */
diff --git a/arch/arm/mach-shmobile/pm-rcar-gen2.c b/arch/arm/mach-shmobile/pm-rcar-gen2.c
index 691ac16..7768fd1 100644
--- a/arch/arm/mach-shmobile/pm-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/pm-rcar-gen2.c
@@ -37,11 +37,7 @@
 
 static void __init rcar_gen2_sysc_init(u32 syscier)
 {
-	void __iomem *base = rcar_sysc_init(0xe6180000);
-
-	/* enable all interrupt sources, but do not use interrupt handler */
-	iowrite32(syscier, base + SYSCIER);
-	iowrite32(0, base + SYSCIMR);
+	rcar_sysc_init(0xe6180000, syscier);
 }
 
 #else /* CONFIG_SMP */
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
index 189d215..c19b827 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi
@@ -5,6 +5,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/hisi,hi6220-resets.h>
 #include <dt-bindings/clock/hi6220-clock.h>
 #include <dt-bindings/pinctrl/hisi.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -252,6 +253,7 @@
 			compatible = "hisilicon,hi6220-mediactrl", "syscon";
 			reg = <0x0 0xf4410000 0x0 0x1000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		pm_ctrl: pm_ctrl@f7032000 {
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index c5a7de9b..3b205e2 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -132,6 +132,19 @@
 	  with various RSB based devices, such as AXP223, AXP8XX PMICs,
 	  and AC100/AC200 ICs.
 
+# TODO: This uses pm_clk_*() symbols that aren't exported in v4.7 and hence
+# the driver will fail to build as a module. However there are patches to
+# address that queued for v4.8, so this can be turned into a tristate symbol
+# after v4.8-rc1.
+config TEGRA_ACONNECT
+	bool "Tegra ACONNECT Bus Driver"
+	depends on ARCH_TEGRA_210_SOC
+	depends on OF && PM
+	select PM_CLK
+	help
+	  Driver for the Tegra ACONNECT bus which is used to interface with
+	  the devices inside the Audio Processing Engine (APE) for Tegra210.
+
 config UNIPHIER_SYSTEM_BUS
 	tristate "UniPhier System Bus driver"
 	depends on ARCH_UNIPHIER && OF
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index ccff007..ac84cc4 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -17,5 +17,6 @@
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_SIMPLE_PM_BUS)	+= simple-pm-bus.o
+obj-$(CONFIG_TEGRA_ACONNECT)	+= tegra-aconnect.o
 obj-$(CONFIG_UNIPHIER_SYSTEM_BUS)	+= uniphier-system-bus.o
 obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o
diff --git a/drivers/bus/tegra-aconnect.c b/drivers/bus/tegra-aconnect.c
new file mode 100644
index 0000000..7e4104b
--- /dev/null
+++ b/drivers/bus/tegra-aconnect.c
@@ -0,0 +1,112 @@
+/*
+ * Tegra ACONNECT Bus Driver
+ *
+ * Copyright (C) 2016, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_clock.h>
+#include <linux/pm_runtime.h>
+
+static int tegra_aconnect_add_clock(struct device *dev, char *name)
+{
+	struct clk *clk;
+	int ret;
+
+	clk = clk_get(dev, name);
+	if (IS_ERR(clk)) {
+		dev_err(dev, "%s clock not found\n", name);
+		return PTR_ERR(clk);
+	}
+
+	ret = pm_clk_add_clk(dev, clk);
+	if (ret)
+		clk_put(clk);
+
+	return ret;
+}
+
+static int tegra_aconnect_probe(struct platform_device *pdev)
+{
+	int ret;
+
+	if (!pdev->dev.of_node)
+		return -EINVAL;
+
+	ret = pm_clk_create(&pdev->dev);
+	if (ret)
+		return ret;
+
+	ret = tegra_aconnect_add_clock(&pdev->dev, "ape");
+	if (ret)
+		goto clk_destroy;
+
+	ret = tegra_aconnect_add_clock(&pdev->dev, "apb2ape");
+	if (ret)
+		goto clk_destroy;
+
+	pm_runtime_enable(&pdev->dev);
+
+	of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+
+	dev_info(&pdev->dev, "Tegra ACONNECT bus registered\n");
+
+	return 0;
+
+clk_destroy:
+	pm_clk_destroy(&pdev->dev);
+
+	return ret;
+}
+
+static int tegra_aconnect_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+
+	pm_clk_destroy(&pdev->dev);
+
+	return 0;
+}
+
+static int tegra_aconnect_runtime_resume(struct device *dev)
+{
+	return pm_clk_resume(dev);
+}
+
+static int tegra_aconnect_runtime_suspend(struct device *dev)
+{
+	return pm_clk_suspend(dev);
+}
+
+static const struct dev_pm_ops tegra_aconnect_pm_ops = {
+	SET_RUNTIME_PM_OPS(tegra_aconnect_runtime_suspend,
+			   tegra_aconnect_runtime_resume, NULL)
+};
+
+static const struct of_device_id tegra_aconnect_of_match[] = {
+	{ .compatible = "nvidia,tegra210-aconnect", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, tegra_aconnect_of_match);
+
+static struct platform_driver tegra_aconnect_driver = {
+	.probe = tegra_aconnect_probe,
+	.remove = tegra_aconnect_remove,
+	.driver = {
+		.name = "tegra-aconnect",
+		.of_match_table = tegra_aconnect_of_match,
+		.pm = &tegra_aconnect_pm_ops,
+	},
+};
+module_platform_driver(tegra_aconnect_driver);
+
+MODULE_DESCRIPTION("NVIDIA Tegra ACONNECT Bus Driver");
+MODULE_AUTHOR("Jon Hunter <jonathanh@nvidia.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/clk/clk-clps711x.c b/drivers/clk/clk-clps711x.c
index 1f60b02..adaf109 100644
--- a/drivers/clk/clk-clps711x.c
+++ b/drivers/clk/clk-clps711x.c
@@ -184,5 +184,5 @@
 	of_clk_add_provider(np, of_clk_src_onecell_get,
 			    &clps711x_clk->clk_data);
 }
-CLK_OF_DECLARE(clps711x, "cirrus,clps711x-clk", clps711x_clk_init_dt);
+CLK_OF_DECLARE(clps711x, "cirrus,ep7209-clk", clps711x_clk_init_dt);
 #endif
diff --git a/drivers/clocksource/clps711x-timer.c b/drivers/clocksource/clps711x-timer.c
index cdd86e3..7c65f9e 100644
--- a/drivers/clocksource/clps711x-timer.c
+++ b/drivers/clocksource/clps711x-timer.c
@@ -121,5 +121,5 @@
 		break;
 	}
 }
-CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
+CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,ep7209-timer", clps711x_timer_init);
 #endif
diff --git a/drivers/cpufreq/s5pv210-cpufreq.c b/drivers/cpufreq/s5pv210-cpufreq.c
index 06d8591..392b29a 100644
--- a/drivers/cpufreq/s5pv210-cpufreq.c
+++ b/drivers/cpufreq/s5pv210-cpufreq.c
@@ -220,7 +220,7 @@
 
 	tmp1 /= tmp;
 
-	__raw_writel(tmp1, reg);
+	writel_relaxed(tmp1, reg);
 }
 
 static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
@@ -301,29 +301,29 @@
 		 * 1. Temporary Change divider for MFC and G3D
 		 * SCLKA2M(200/1=200)->(200/4=50)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_DIV2);
+		reg = readl_relaxed(S5P_CLK_DIV2);
 		reg &= ~(S5P_CLKDIV2_G3D_MASK | S5P_CLKDIV2_MFC_MASK);
 		reg |= (3 << S5P_CLKDIV2_G3D_SHIFT) |
 			(3 << S5P_CLKDIV2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_DIV2);
+		writel_relaxed(reg, S5P_CLK_DIV2);
 
 		/* For MFC, G3D dividing */
 		do {
-			reg = __raw_readl(S5P_CLKDIV_STAT0);
+			reg = readl_relaxed(S5P_CLKDIV_STAT0);
 		} while (reg & ((1 << 16) | (1 << 17)));
 
 		/*
 		 * 2. Change SCLKA2M(200Mhz)to SCLKMPLL in MFC_MUX, G3D MUX
 		 * (200/4=50)->(667/4=166)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_SRC2);
+		reg = readl_relaxed(S5P_CLK_SRC2);
 		reg &= ~(S5P_CLKSRC2_G3D_MASK | S5P_CLKSRC2_MFC_MASK);
 		reg |= (1 << S5P_CLKSRC2_G3D_SHIFT) |
 			(1 << S5P_CLKSRC2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC2);
+		writel_relaxed(reg, S5P_CLK_SRC2);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT1);
+			reg = readl_relaxed(S5P_CLKMUX_STAT1);
 		} while (reg & ((1 << 7) | (1 << 3)));
 
 		/*
@@ -335,19 +335,19 @@
 			s5pv210_set_refresh(DMC1, 133000);
 
 		/* 4. SCLKAPLL -> SCLKMPLL */
-		reg = __raw_readl(S5P_CLK_SRC0);
+		reg = readl_relaxed(S5P_CLK_SRC0);
 		reg &= ~(S5P_CLKSRC0_MUX200_MASK);
 		reg |= (0x1 << S5P_CLKSRC0_MUX200_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC0);
+		writel_relaxed(reg, S5P_CLK_SRC0);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT0);
+			reg = readl_relaxed(S5P_CLKMUX_STAT0);
 		} while (reg & (0x1 << 18));
 
 	}
 
 	/* Change divider */
-	reg = __raw_readl(S5P_CLK_DIV0);
+	reg = readl_relaxed(S5P_CLK_DIV0);
 
 	reg &= ~(S5P_CLKDIV0_APLL_MASK | S5P_CLKDIV0_A2M_MASK |
 		S5P_CLKDIV0_HCLK200_MASK | S5P_CLKDIV0_PCLK100_MASK |
@@ -363,25 +363,25 @@
 		(clkdiv_val[index][6] << S5P_CLKDIV0_HCLK133_SHIFT) |
 		(clkdiv_val[index][7] << S5P_CLKDIV0_PCLK66_SHIFT));
 
-	__raw_writel(reg, S5P_CLK_DIV0);
+	writel_relaxed(reg, S5P_CLK_DIV0);
 
 	do {
-		reg = __raw_readl(S5P_CLKDIV_STAT0);
+		reg = readl_relaxed(S5P_CLKDIV_STAT0);
 	} while (reg & 0xff);
 
 	/* ARM MCS value changed */
-	reg = __raw_readl(S5P_ARM_MCS_CON);
+	reg = readl_relaxed(S5P_ARM_MCS_CON);
 	reg &= ~0x3;
 	if (index >= L3)
 		reg |= 0x3;
 	else
 		reg |= 0x1;
 
-	__raw_writel(reg, S5P_ARM_MCS_CON);
+	writel_relaxed(reg, S5P_ARM_MCS_CON);
 
 	if (pll_changing) {
 		/* 5. Set Lock time = 30us*24Mhz = 0x2cf */
-		__raw_writel(0x2cf, S5P_APLL_LOCK);
+		writel_relaxed(0x2cf, S5P_APLL_LOCK);
 
 		/*
 		 * 6. Turn on APLL
@@ -389,12 +389,12 @@
 		 * 6-2. Wait untile the PLL is locked
 		 */
 		if (index == L0)
-			__raw_writel(APLL_VAL_1000, S5P_APLL_CON);
+			writel_relaxed(APLL_VAL_1000, S5P_APLL_CON);
 		else
-			__raw_writel(APLL_VAL_800, S5P_APLL_CON);
+			writel_relaxed(APLL_VAL_800, S5P_APLL_CON);
 
 		do {
-			reg = __raw_readl(S5P_APLL_CON);
+			reg = readl_relaxed(S5P_APLL_CON);
 		} while (!(reg & (0x1 << 29)));
 
 		/*
@@ -402,39 +402,39 @@
 		 * to SCLKA2M(200Mhz) in MFC_MUX and G3D MUX
 		 * (667/4=166)->(200/4=50)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_SRC2);
+		reg = readl_relaxed(S5P_CLK_SRC2);
 		reg &= ~(S5P_CLKSRC2_G3D_MASK | S5P_CLKSRC2_MFC_MASK);
 		reg |= (0 << S5P_CLKSRC2_G3D_SHIFT) |
 			(0 << S5P_CLKSRC2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC2);
+		writel_relaxed(reg, S5P_CLK_SRC2);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT1);
+			reg = readl_relaxed(S5P_CLKMUX_STAT1);
 		} while (reg & ((1 << 7) | (1 << 3)));
 
 		/*
 		 * 8. Change divider for MFC and G3D
 		 * (200/4=50)->(200/1=200)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_DIV2);
+		reg = readl_relaxed(S5P_CLK_DIV2);
 		reg &= ~(S5P_CLKDIV2_G3D_MASK | S5P_CLKDIV2_MFC_MASK);
 		reg |= (clkdiv_val[index][10] << S5P_CLKDIV2_G3D_SHIFT) |
 			(clkdiv_val[index][9] << S5P_CLKDIV2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_DIV2);
+		writel_relaxed(reg, S5P_CLK_DIV2);
 
 		/* For MFC, G3D dividing */
 		do {
-			reg = __raw_readl(S5P_CLKDIV_STAT0);
+			reg = readl_relaxed(S5P_CLKDIV_STAT0);
 		} while (reg & ((1 << 16) | (1 << 17)));
 
 		/* 9. Change MPLL to APLL in MSYS_MUX */
-		reg = __raw_readl(S5P_CLK_SRC0);
+		reg = readl_relaxed(S5P_CLK_SRC0);
 		reg &= ~(S5P_CLKSRC0_MUX200_MASK);
 		reg |= (0x0 << S5P_CLKSRC0_MUX200_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC0);
+		writel_relaxed(reg, S5P_CLK_SRC0);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT0);
+			reg = readl_relaxed(S5P_CLKMUX_STAT0);
 		} while (reg & (0x1 << 18));
 
 		/*
@@ -451,13 +451,13 @@
 	 * and memory refresh parameter should be changed
 	 */
 	if (bus_speed_changing) {
-		reg = __raw_readl(S5P_CLK_DIV6);
+		reg = readl_relaxed(S5P_CLK_DIV6);
 		reg &= ~S5P_CLKDIV6_ONEDRAM_MASK;
 		reg |= (clkdiv_val[index][8] << S5P_CLKDIV6_ONEDRAM_SHIFT);
-		__raw_writel(reg, S5P_CLK_DIV6);
+		writel_relaxed(reg, S5P_CLK_DIV6);
 
 		do {
-			reg = __raw_readl(S5P_CLKDIV_STAT1);
+			reg = readl_relaxed(S5P_CLKDIV_STAT1);
 		} while (reg & (1 << 15));
 
 		/* Reconfigure DRAM refresh counter value */
@@ -497,7 +497,7 @@
 {
 	unsigned long val;
 
-	val = __raw_readl(dmc_reg + 0x4);
+	val = readl_relaxed(dmc_reg + 0x4);
 	val = (val & (0xf << 8));
 
 	return val >> 8;
@@ -542,10 +542,10 @@
 	}
 
 	/* Find current refresh counter and frequency each DMC */
-	s5pv210_dram_conf[0].refresh = (__raw_readl(dmc_base[0] + 0x30) * 1000);
+	s5pv210_dram_conf[0].refresh = (readl_relaxed(dmc_base[0] + 0x30) * 1000);
 	s5pv210_dram_conf[0].freq = clk_get_rate(dmc0_clk);
 
-	s5pv210_dram_conf[1].refresh = (__raw_readl(dmc_base[1] + 0x30) * 1000);
+	s5pv210_dram_conf[1].refresh = (readl_relaxed(dmc_base[1] + 0x30) * 1000);
 	s5pv210_dram_conf[1].freq = clk_get_rate(dmc1_clk);
 
 	policy->suspend_freq = SLEEP_FREQ;
diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
index 6664f11..541d3fb 100644
--- a/drivers/firmware/Kconfig
+++ b/drivers/firmware/Kconfig
@@ -10,7 +10,7 @@
 
 config ARM_SCPI_PROTOCOL
 	tristate "ARM System Control and Power Interface (SCPI) Message Protocol"
-	depends on ARM_MHU
+	depends on MAILBOX
 	help
 	  System Control and Power Interface (SCPI) Message Protocol is
 	  defined for the purpose of communication between the Application
@@ -27,6 +27,16 @@
 	  This protocol library provides interface for all the client drivers
 	  making use of the features offered by the SCP.
 
+config ARM_SCPI_POWER_DOMAIN
+	tristate "SCPI power domain driver"
+	depends on ARM_SCPI_PROTOCOL || COMPILE_TEST
+	default y
+	select PM_GENERIC_DOMAINS if PM
+	select PM_GENERIC_DOMAINS_OF if PM
+	help
+	  This enables support for the SCPI power domains which can be
+	  enabled or disabled via the SCP firmware
+
 config EDD
 	tristate "BIOS Enhanced Disk Drive calls determine boot disk"
 	depends on X86
@@ -184,6 +194,7 @@
 config QCOM_SCM
 	bool
 	depends on ARM || ARM64
+	select RESET_CONTROLLER
 
 config QCOM_SCM_32
 	def_bool y
diff --git a/drivers/firmware/Makefile b/drivers/firmware/Makefile
index 474bada..44a59dc 100644
--- a/drivers/firmware/Makefile
+++ b/drivers/firmware/Makefile
@@ -3,6 +3,7 @@
 #
 obj-$(CONFIG_ARM_PSCI_FW)	+= psci.o
 obj-$(CONFIG_ARM_SCPI_PROTOCOL)	+= arm_scpi.o
+obj-$(CONFIG_ARM_SCPI_POWER_DOMAIN) += scpi_pm_domain.o
 obj-$(CONFIG_DMI)		+= dmi_scan.o
 obj-$(CONFIG_DMI_SYSFS)		+= dmi-sysfs.o
 obj-$(CONFIG_EDD)		+= edd.o
diff --git a/drivers/firmware/arm_scpi.c b/drivers/firmware/arm_scpi.c
index 7e3e595..4388937 100644
--- a/drivers/firmware/arm_scpi.c
+++ b/drivers/firmware/arm_scpi.c
@@ -210,10 +210,6 @@
 	} opps[MAX_DVFS_OPPS];
 } __packed;
 
-struct dvfs_get {
-	u8 index;
-} __packed;
-
 struct dvfs_set {
 	u8 domain;
 	u8 index;
@@ -235,6 +231,11 @@
 	__le32 hi_val;
 } __packed;
 
+struct dev_pstate_set {
+	u16 dev_id;
+	u8 pstate;
+} __packed;
+
 static struct scpi_drvinfo *scpi_info;
 
 static int scpi_linux_errmap[SCPI_ERR_MAX] = {
@@ -431,11 +432,11 @@
 static int scpi_dvfs_get_idx(u8 domain)
 {
 	int ret;
-	struct dvfs_get dvfs;
+	u8 dvfs_idx;
 
 	ret = scpi_send_message(SCPI_CMD_GET_DVFS, &domain, sizeof(domain),
-				&dvfs, sizeof(dvfs));
-	return ret ? ret : dvfs.index;
+				&dvfs_idx, sizeof(dvfs_idx));
+	return ret ? ret : dvfs_idx;
 }
 
 static int scpi_dvfs_set_idx(u8 domain, u8 index)
@@ -526,7 +527,7 @@
 	return ret;
 }
 
-int scpi_sensor_get_value(u16 sensor, u64 *val)
+static int scpi_sensor_get_value(u16 sensor, u64 *val)
 {
 	__le16 id = cpu_to_le16(sensor);
 	struct sensor_value buf;
@@ -541,6 +542,29 @@
 	return ret;
 }
 
+static int scpi_device_get_power_state(u16 dev_id)
+{
+	int ret;
+	u8 pstate;
+	__le16 id = cpu_to_le16(dev_id);
+
+	ret = scpi_send_message(SCPI_CMD_GET_DEVICE_PWR_STATE, &id,
+				sizeof(id), &pstate, sizeof(pstate));
+	return ret ? ret : pstate;
+}
+
+static int scpi_device_set_power_state(u16 dev_id, u8 pstate)
+{
+	int stat;
+	struct dev_pstate_set dev_set = {
+		.dev_id = cpu_to_le16(dev_id),
+		.pstate = pstate,
+	};
+
+	return scpi_send_message(SCPI_CMD_SET_DEVICE_PWR_STATE, &dev_set,
+				 sizeof(dev_set), &stat, sizeof(stat));
+}
+
 static struct scpi_ops scpi_ops = {
 	.get_version = scpi_get_version,
 	.clk_get_range = scpi_clk_get_range,
@@ -552,6 +576,8 @@
 	.sensor_get_capability = scpi_sensor_get_capability,
 	.sensor_get_info = scpi_sensor_get_info,
 	.sensor_get_value = scpi_sensor_get_value,
+	.device_get_power_state = scpi_device_get_power_state,
+	.device_set_power_state = scpi_device_set_power_state,
 };
 
 struct scpi_ops *get_scpi_ops(void)
diff --git a/drivers/firmware/qcom_scm-32.c b/drivers/firmware/qcom_scm-32.c
index 0883292..c6aeedb 100644
--- a/drivers/firmware/qcom_scm-32.c
+++ b/drivers/firmware/qcom_scm-32.c
@@ -23,8 +23,7 @@
 #include <linux/errno.h>
 #include <linux/err.h>
 #include <linux/qcom_scm.h>
-
-#include <asm/cacheflush.h>
+#include <linux/dma-mapping.h>
 
 #include "qcom_scm.h"
 
@@ -97,44 +96,6 @@
 };
 
 /**
- * alloc_qcom_scm_command() - Allocate an SCM command
- * @cmd_size: size of the command buffer
- * @resp_size: size of the response buffer
- *
- * Allocate an SCM command, including enough room for the command
- * and response headers as well as the command and response buffers.
- *
- * Returns a valid &qcom_scm_command on success or %NULL if the allocation fails.
- */
-static struct qcom_scm_command *alloc_qcom_scm_command(size_t cmd_size, size_t resp_size)
-{
-	struct qcom_scm_command *cmd;
-	size_t len = sizeof(*cmd) + sizeof(struct qcom_scm_response) + cmd_size +
-		resp_size;
-	u32 offset;
-
-	cmd = kzalloc(PAGE_ALIGN(len), GFP_KERNEL);
-	if (cmd) {
-		cmd->len = cpu_to_le32(len);
-		offset = offsetof(struct qcom_scm_command, buf);
-		cmd->buf_offset = cpu_to_le32(offset);
-		cmd->resp_hdr_offset = cpu_to_le32(offset + cmd_size);
-	}
-	return cmd;
-}
-
-/**
- * free_qcom_scm_command() - Free an SCM command
- * @cmd: command to free
- *
- * Free an SCM command.
- */
-static inline void free_qcom_scm_command(struct qcom_scm_command *cmd)
-{
-	kfree(cmd);
-}
-
-/**
  * qcom_scm_command_to_response() - Get a pointer to a qcom_scm_response
  * @cmd: command
  *
@@ -168,23 +129,6 @@
 	return (void *)rsp + le32_to_cpu(rsp->buf_offset);
 }
 
-static int qcom_scm_remap_error(int err)
-{
-	pr_err("qcom_scm_call failed with error code %d\n", err);
-	switch (err) {
-	case QCOM_SCM_ERROR:
-		return -EIO;
-	case QCOM_SCM_EINVAL_ADDR:
-	case QCOM_SCM_EINVAL_ARG:
-		return -EINVAL;
-	case QCOM_SCM_EOPNOTSUPP:
-		return -EOPNOTSUPP;
-	case QCOM_SCM_ENOMEM:
-		return -ENOMEM;
-	}
-	return -EINVAL;
-}
-
 static u32 smc(u32 cmd_addr)
 {
 	int context_id;
@@ -209,45 +153,9 @@
 	return r0;
 }
 
-static int __qcom_scm_call(const struct qcom_scm_command *cmd)
-{
-	int ret;
-	u32 cmd_addr = virt_to_phys(cmd);
-
-	/*
-	 * Flush the command buffer so that the secure world sees
-	 * the correct data.
-	 */
-	secure_flush_area(cmd, cmd->len);
-
-	ret = smc(cmd_addr);
-	if (ret < 0)
-		ret = qcom_scm_remap_error(ret);
-
-	return ret;
-}
-
-static void qcom_scm_inv_range(unsigned long start, unsigned long end)
-{
-	u32 cacheline_size, ctr;
-
-	asm volatile("mrc p15, 0, %0, c0, c0, 1" : "=r" (ctr));
-	cacheline_size = 4 << ((ctr >> 16) & 0xf);
-
-	start = round_down(start, cacheline_size);
-	end = round_up(end, cacheline_size);
-	outer_inv_range(start, end);
-	while (start < end) {
-		asm ("mcr p15, 0, %0, c7, c6, 1" : : "r" (start)
-		     : "memory");
-		start += cacheline_size;
-	}
-	dsb();
-	isb();
-}
-
 /**
  * qcom_scm_call() - Send an SCM command
+ * @dev: struct device
  * @svc_id: service identifier
  * @cmd_id: command identifier
  * @cmd_buf: command buffer
@@ -264,42 +172,59 @@
  * and response buffers is taken care of by qcom_scm_call; however, callers are
  * responsible for any other cached buffers passed over to the secure world.
  */
-static int qcom_scm_call(u32 svc_id, u32 cmd_id, const void *cmd_buf,
-			size_t cmd_len, void *resp_buf, size_t resp_len)
+static int qcom_scm_call(struct device *dev, u32 svc_id, u32 cmd_id,
+			 const void *cmd_buf, size_t cmd_len, void *resp_buf,
+			 size_t resp_len)
 {
 	int ret;
 	struct qcom_scm_command *cmd;
 	struct qcom_scm_response *rsp;
-	unsigned long start, end;
+	size_t alloc_len = sizeof(*cmd) + cmd_len + sizeof(*rsp) + resp_len;
+	dma_addr_t cmd_phys;
 
-	cmd = alloc_qcom_scm_command(cmd_len, resp_len);
+	cmd = kzalloc(PAGE_ALIGN(alloc_len), GFP_KERNEL);
 	if (!cmd)
 		return -ENOMEM;
 
+	cmd->len = cpu_to_le32(alloc_len);
+	cmd->buf_offset = cpu_to_le32(sizeof(*cmd));
+	cmd->resp_hdr_offset = cpu_to_le32(sizeof(*cmd) + cmd_len);
+
 	cmd->id = cpu_to_le32((svc_id << 10) | cmd_id);
 	if (cmd_buf)
 		memcpy(qcom_scm_get_command_buffer(cmd), cmd_buf, cmd_len);
 
+	rsp = qcom_scm_command_to_response(cmd);
+
+	cmd_phys = dma_map_single(dev, cmd, alloc_len, DMA_TO_DEVICE);
+	if (dma_mapping_error(dev, cmd_phys)) {
+		kfree(cmd);
+		return -ENOMEM;
+	}
+
 	mutex_lock(&qcom_scm_lock);
-	ret = __qcom_scm_call(cmd);
+	ret = smc(cmd_phys);
+	if (ret < 0)
+		ret = qcom_scm_remap_error(ret);
 	mutex_unlock(&qcom_scm_lock);
 	if (ret)
 		goto out;
 
-	rsp = qcom_scm_command_to_response(cmd);
-	start = (unsigned long)rsp;
-
 	do {
-		qcom_scm_inv_range(start, start + sizeof(*rsp));
+		dma_sync_single_for_cpu(dev, cmd_phys + sizeof(*cmd) + cmd_len,
+					sizeof(*rsp), DMA_FROM_DEVICE);
 	} while (!rsp->is_complete);
 
-	end = (unsigned long)qcom_scm_get_response_buffer(rsp) + resp_len;
-	qcom_scm_inv_range(start, end);
-
-	if (resp_buf)
-		memcpy(resp_buf, qcom_scm_get_response_buffer(rsp), resp_len);
+	if (resp_buf) {
+		dma_sync_single_for_cpu(dev, cmd_phys + sizeof(*cmd) + cmd_len +
+					le32_to_cpu(rsp->buf_offset),
+					resp_len, DMA_FROM_DEVICE);
+		memcpy(resp_buf, qcom_scm_get_response_buffer(rsp),
+		       resp_len);
+	}
 out:
-	free_qcom_scm_command(cmd);
+	dma_unmap_single(dev, cmd_phys, alloc_len, DMA_TO_DEVICE);
+	kfree(cmd);
 	return ret;
 }
 
@@ -342,6 +267,41 @@
 	return r0;
 }
 
+/**
+ * qcom_scm_call_atomic2() - Send an atomic SCM command with two arguments
+ * @svc_id:	service identifier
+ * @cmd_id:	command identifier
+ * @arg1:	first argument
+ * @arg2:	second argument
+ *
+ * This shall only be used with commands that are guaranteed to be
+ * uninterruptable, atomic and SMP safe.
+ */
+static s32 qcom_scm_call_atomic2(u32 svc, u32 cmd, u32 arg1, u32 arg2)
+{
+	int context_id;
+
+	register u32 r0 asm("r0") = SCM_ATOMIC(svc, cmd, 2);
+	register u32 r1 asm("r1") = (u32)&context_id;
+	register u32 r2 asm("r2") = arg1;
+	register u32 r3 asm("r3") = arg2;
+
+	asm volatile(
+			__asmeq("%0", "r0")
+			__asmeq("%1", "r0")
+			__asmeq("%2", "r1")
+			__asmeq("%3", "r2")
+			__asmeq("%4", "r3")
+#ifdef REQUIRES_SEC
+			".arch_extension sec\n"
+#endif
+			"smc    #0      @ switch to secure world\n"
+			: "=r" (r0)
+			: "r" (r0), "r" (r1), "r" (r2), "r" (r3)
+			);
+	return r0;
+}
+
 u32 qcom_scm_get_version(void)
 {
 	int context_id;
@@ -378,22 +338,6 @@
 }
 EXPORT_SYMBOL(qcom_scm_get_version);
 
-/*
- * Set the cold/warm boot address for one of the CPU cores.
- */
-static int qcom_scm_set_boot_addr(u32 addr, int flags)
-{
-	struct {
-		__le32 flags;
-		__le32 addr;
-	} cmd;
-
-	cmd.addr = cpu_to_le32(addr);
-	cmd.flags = cpu_to_le32(flags);
-	return qcom_scm_call(QCOM_SCM_SVC_BOOT, QCOM_SCM_BOOT_ADDR,
-			&cmd, sizeof(cmd), NULL, 0);
-}
-
 /**
  * qcom_scm_set_cold_boot_addr() - Set the cold boot address for cpus
  * @entry: Entry point function for the cpus
@@ -423,7 +367,8 @@
 			set_cpu_present(cpu, false);
 	}
 
-	return qcom_scm_set_boot_addr(virt_to_phys(entry), flags);
+	return qcom_scm_call_atomic2(QCOM_SCM_SVC_BOOT, QCOM_SCM_BOOT_ADDR,
+				    flags, virt_to_phys(entry));
 }
 
 /**
@@ -434,11 +379,16 @@
  * Set the Linux entry point for the SCM to transfer control to when coming
  * out of a power down. CPU power down may be executed on cpuidle or hotplug.
  */
-int __qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus)
+int __qcom_scm_set_warm_boot_addr(struct device *dev, void *entry,
+				  const cpumask_t *cpus)
 {
 	int ret;
 	int flags = 0;
 	int cpu;
+	struct {
+		__le32 flags;
+		__le32 addr;
+	} cmd;
 
 	/*
 	 * Reassign only if we are switching from hotplug entry point
@@ -454,7 +404,10 @@
 	if (!flags)
 		return 0;
 
-	ret = qcom_scm_set_boot_addr(virt_to_phys(entry), flags);
+	cmd.addr = cpu_to_le32(virt_to_phys(entry));
+	cmd.flags = cpu_to_le32(flags);
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_BOOT, QCOM_SCM_BOOT_ADDR,
+			    &cmd, sizeof(cmd), NULL, 0);
 	if (!ret) {
 		for_each_cpu(cpu, cpus)
 			qcom_scm_wb[cpu].entry = entry;
@@ -477,25 +430,133 @@
 			flags & QCOM_SCM_FLUSH_FLAG_MASK);
 }
 
-int __qcom_scm_is_call_available(u32 svc_id, u32 cmd_id)
+int __qcom_scm_is_call_available(struct device *dev, u32 svc_id, u32 cmd_id)
 {
 	int ret;
 	__le32 svc_cmd = cpu_to_le32((svc_id << 10) | cmd_id);
 	__le32 ret_val = 0;
 
-	ret = qcom_scm_call(QCOM_SCM_SVC_INFO, QCOM_IS_CALL_AVAIL_CMD, &svc_cmd,
-			sizeof(svc_cmd), &ret_val, sizeof(ret_val));
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_INFO, QCOM_IS_CALL_AVAIL_CMD,
+			    &svc_cmd, sizeof(svc_cmd), &ret_val,
+			    sizeof(ret_val));
 	if (ret)
 		return ret;
 
 	return le32_to_cpu(ret_val);
 }
 
-int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp)
+int __qcom_scm_hdcp_req(struct device *dev, struct qcom_scm_hdcp_req *req,
+			u32 req_cnt, u32 *resp)
 {
 	if (req_cnt > QCOM_SCM_HDCP_MAX_REQ_CNT)
 		return -ERANGE;
 
-	return qcom_scm_call(QCOM_SCM_SVC_HDCP, QCOM_SCM_CMD_HDCP,
+	return qcom_scm_call(dev, QCOM_SCM_SVC_HDCP, QCOM_SCM_CMD_HDCP,
 		req, req_cnt * sizeof(*req), resp, sizeof(*resp));
 }
+
+void __qcom_scm_init(void)
+{
+}
+
+bool __qcom_scm_pas_supported(struct device *dev, u32 peripheral)
+{
+	__le32 out;
+	__le32 in;
+	int ret;
+
+	in = cpu_to_le32(peripheral);
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+			    QCOM_SCM_PAS_IS_SUPPORTED_CMD,
+			    &in, sizeof(in),
+			    &out, sizeof(out));
+
+	return ret ? false : !!out;
+}
+
+int __qcom_scm_pas_init_image(struct device *dev, u32 peripheral,
+			      dma_addr_t metadata_phys)
+{
+	__le32 scm_ret;
+	int ret;
+	struct {
+		__le32 proc;
+		__le32 image_addr;
+	} request;
+
+	request.proc = cpu_to_le32(peripheral);
+	request.image_addr = cpu_to_le32(metadata_phys);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+			    QCOM_SCM_PAS_INIT_IMAGE_CMD,
+			    &request, sizeof(request),
+			    &scm_ret, sizeof(scm_ret));
+
+	return ret ? : le32_to_cpu(scm_ret);
+}
+
+int __qcom_scm_pas_mem_setup(struct device *dev, u32 peripheral,
+			     phys_addr_t addr, phys_addr_t size)
+{
+	__le32 scm_ret;
+	int ret;
+	struct {
+		__le32 proc;
+		__le32 addr;
+		__le32 len;
+	} request;
+
+	request.proc = cpu_to_le32(peripheral);
+	request.addr = cpu_to_le32(addr);
+	request.len = cpu_to_le32(size);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+			    QCOM_SCM_PAS_MEM_SETUP_CMD,
+			    &request, sizeof(request),
+			    &scm_ret, sizeof(scm_ret));
+
+	return ret ? : le32_to_cpu(scm_ret);
+}
+
+int __qcom_scm_pas_auth_and_reset(struct device *dev, u32 peripheral)
+{
+	__le32 out;
+	__le32 in;
+	int ret;
+
+	in = cpu_to_le32(peripheral);
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+			    QCOM_SCM_PAS_AUTH_AND_RESET_CMD,
+			    &in, sizeof(in),
+			    &out, sizeof(out));
+
+	return ret ? : le32_to_cpu(out);
+}
+
+int __qcom_scm_pas_shutdown(struct device *dev, u32 peripheral)
+{
+	__le32 out;
+	__le32 in;
+	int ret;
+
+	in = cpu_to_le32(peripheral);
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+			    QCOM_SCM_PAS_SHUTDOWN_CMD,
+			    &in, sizeof(in),
+			    &out, sizeof(out));
+
+	return ret ? : le32_to_cpu(out);
+}
+
+int __qcom_scm_pas_mss_reset(struct device *dev, bool reset)
+{
+	__le32 out;
+	__le32 in = cpu_to_le32(reset);
+	int ret;
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_MSS_RESET,
+			&in, sizeof(in),
+			&out, sizeof(out));
+
+	return ret ? : le32_to_cpu(out);
+}
diff --git a/drivers/firmware/qcom_scm-64.c b/drivers/firmware/qcom_scm-64.c
index bb6555f..4a0f5ea 100644
--- a/drivers/firmware/qcom_scm-64.c
+++ b/drivers/firmware/qcom_scm-64.c
@@ -12,7 +12,150 @@
 
 #include <linux/io.h>
 #include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
 #include <linux/qcom_scm.h>
+#include <linux/arm-smccc.h>
+#include <linux/dma-mapping.h>
+
+#include "qcom_scm.h"
+
+#define QCOM_SCM_FNID(s, c) ((((s) & 0xFF) << 8) | ((c) & 0xFF))
+
+#define MAX_QCOM_SCM_ARGS 10
+#define MAX_QCOM_SCM_RETS 3
+
+enum qcom_scm_arg_types {
+	QCOM_SCM_VAL,
+	QCOM_SCM_RO,
+	QCOM_SCM_RW,
+	QCOM_SCM_BUFVAL,
+};
+
+#define QCOM_SCM_ARGS_IMPL(num, a, b, c, d, e, f, g, h, i, j, ...) (\
+			   (((a) & 0x3) << 4) | \
+			   (((b) & 0x3) << 6) | \
+			   (((c) & 0x3) << 8) | \
+			   (((d) & 0x3) << 10) | \
+			   (((e) & 0x3) << 12) | \
+			   (((f) & 0x3) << 14) | \
+			   (((g) & 0x3) << 16) | \
+			   (((h) & 0x3) << 18) | \
+			   (((i) & 0x3) << 20) | \
+			   (((j) & 0x3) << 22) | \
+			   ((num) & 0xf))
+
+#define QCOM_SCM_ARGS(...) QCOM_SCM_ARGS_IMPL(__VA_ARGS__, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0)
+
+/**
+ * struct qcom_scm_desc
+ * @arginfo:	Metadata describing the arguments in args[]
+ * @args:	The array of arguments for the secure syscall
+ * @res:	The values returned by the secure syscall
+ */
+struct qcom_scm_desc {
+	u32 arginfo;
+	u64 args[MAX_QCOM_SCM_ARGS];
+};
+
+static u64 qcom_smccc_convention = -1;
+static DEFINE_MUTEX(qcom_scm_lock);
+
+#define QCOM_SCM_EBUSY_WAIT_MS 30
+#define QCOM_SCM_EBUSY_MAX_RETRY 20
+
+#define N_EXT_QCOM_SCM_ARGS 7
+#define FIRST_EXT_ARG_IDX 3
+#define N_REGISTER_ARGS (MAX_QCOM_SCM_ARGS - N_EXT_QCOM_SCM_ARGS + 1)
+
+/**
+ * qcom_scm_call() - Invoke a syscall in the secure world
+ * @dev:	device
+ * @svc_id:	service identifier
+ * @cmd_id:	command identifier
+ * @desc:	Descriptor structure containing arguments and return values
+ *
+ * Sends a command to the SCM and waits for the command to finish processing.
+ * This should *only* be called in pre-emptible context.
+*/
+static int qcom_scm_call(struct device *dev, u32 svc_id, u32 cmd_id,
+			 const struct qcom_scm_desc *desc,
+			 struct arm_smccc_res *res)
+{
+	int arglen = desc->arginfo & 0xf;
+	int retry_count = 0, i;
+	u32 fn_id = QCOM_SCM_FNID(svc_id, cmd_id);
+	u64 cmd, x5 = desc->args[FIRST_EXT_ARG_IDX];
+	dma_addr_t args_phys = 0;
+	void *args_virt = NULL;
+	size_t alloc_len;
+
+	if (unlikely(arglen > N_REGISTER_ARGS)) {
+		alloc_len = N_EXT_QCOM_SCM_ARGS * sizeof(u64);
+		args_virt = kzalloc(PAGE_ALIGN(alloc_len), GFP_KERNEL);
+
+		if (!args_virt)
+			return -ENOMEM;
+
+		if (qcom_smccc_convention == ARM_SMCCC_SMC_32) {
+			__le32 *args = args_virt;
+
+			for (i = 0; i < N_EXT_QCOM_SCM_ARGS; i++)
+				args[i] = cpu_to_le32(desc->args[i +
+						      FIRST_EXT_ARG_IDX]);
+		} else {
+			__le64 *args = args_virt;
+
+			for (i = 0; i < N_EXT_QCOM_SCM_ARGS; i++)
+				args[i] = cpu_to_le64(desc->args[i +
+						      FIRST_EXT_ARG_IDX]);
+		}
+
+		args_phys = dma_map_single(dev, args_virt, alloc_len,
+					   DMA_TO_DEVICE);
+
+		if (dma_mapping_error(dev, args_phys)) {
+			kfree(args_virt);
+			return -ENOMEM;
+		}
+
+		x5 = args_phys;
+	}
+
+	do {
+		mutex_lock(&qcom_scm_lock);
+
+		cmd = ARM_SMCCC_CALL_VAL(ARM_SMCCC_STD_CALL,
+					 qcom_smccc_convention,
+					 ARM_SMCCC_OWNER_SIP, fn_id);
+
+		do {
+			arm_smccc_smc(cmd, desc->arginfo, desc->args[0],
+				      desc->args[1], desc->args[2], x5, 0, 0,
+				      res);
+		} while (res->a0 == QCOM_SCM_INTERRUPTED);
+
+		mutex_unlock(&qcom_scm_lock);
+
+		if (res->a0 == QCOM_SCM_V2_EBUSY) {
+			if (retry_count++ > QCOM_SCM_EBUSY_MAX_RETRY)
+				break;
+			msleep(QCOM_SCM_EBUSY_WAIT_MS);
+		}
+	}  while (res->a0 == QCOM_SCM_V2_EBUSY);
+
+	if (args_virt) {
+		dma_unmap_single(dev, args_phys, alloc_len, DMA_TO_DEVICE);
+		kfree(args_virt);
+	}
+
+	if (res->a0 < 0)
+		return qcom_scm_remap_error(res->a0);
+
+	return 0;
+}
 
 /**
  * qcom_scm_set_cold_boot_addr() - Set the cold boot address for cpus
@@ -29,13 +172,15 @@
 
 /**
  * qcom_scm_set_warm_boot_addr() - Set the warm boot address for cpus
+ * @dev: Device pointer
  * @entry: Entry point function for the cpus
  * @cpus: The cpumask of cpus that will use the entry point
  *
  * Set the Linux entry point for the SCM to transfer control to when coming
  * out of a power down. CPU power down may be executed on cpuidle or hotplug.
  */
-int __qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus)
+int __qcom_scm_set_warm_boot_addr(struct device *dev, void *entry,
+				  const cpumask_t *cpus)
 {
 	return -ENOTSUPP;
 }
@@ -52,12 +197,164 @@
 {
 }
 
-int __qcom_scm_is_call_available(u32 svc_id, u32 cmd_id)
+int __qcom_scm_is_call_available(struct device *dev, u32 svc_id, u32 cmd_id)
 {
-	return -ENOTSUPP;
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.arginfo = QCOM_SCM_ARGS(1);
+	desc.args[0] = QCOM_SCM_FNID(svc_id, cmd_id) |
+			(ARM_SMCCC_OWNER_SIP << ARM_SMCCC_OWNER_SHIFT);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_INFO, QCOM_IS_CALL_AVAIL_CMD,
+			    &desc, &res);
+
+	return ret ? : res.a1;
 }
 
-int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp)
+int __qcom_scm_hdcp_req(struct device *dev, struct qcom_scm_hdcp_req *req,
+			u32 req_cnt, u32 *resp)
 {
-	return -ENOTSUPP;
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	if (req_cnt > QCOM_SCM_HDCP_MAX_REQ_CNT)
+		return -ERANGE;
+
+	desc.args[0] = req[0].addr;
+	desc.args[1] = req[0].val;
+	desc.args[2] = req[1].addr;
+	desc.args[3] = req[1].val;
+	desc.args[4] = req[2].addr;
+	desc.args[5] = req[2].val;
+	desc.args[6] = req[3].addr;
+	desc.args[7] = req[3].val;
+	desc.args[8] = req[4].addr;
+	desc.args[9] = req[4].val;
+	desc.arginfo = QCOM_SCM_ARGS(10);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_HDCP, QCOM_SCM_CMD_HDCP, &desc,
+			    &res);
+	*resp = res.a1;
+
+	return ret;
+}
+
+void __qcom_scm_init(void)
+{
+	u64 cmd;
+	struct arm_smccc_res res;
+	u32 function = QCOM_SCM_FNID(QCOM_SCM_SVC_INFO, QCOM_IS_CALL_AVAIL_CMD);
+
+	/* First try a SMC64 call */
+	cmd = ARM_SMCCC_CALL_VAL(ARM_SMCCC_FAST_CALL, ARM_SMCCC_SMC_64,
+				 ARM_SMCCC_OWNER_SIP, function);
+
+	arm_smccc_smc(cmd, QCOM_SCM_ARGS(1), cmd & (~BIT(ARM_SMCCC_TYPE_SHIFT)),
+		      0, 0, 0, 0, 0, &res);
+
+	if (!res.a0 && res.a1)
+		qcom_smccc_convention = ARM_SMCCC_SMC_64;
+	else
+		qcom_smccc_convention = ARM_SMCCC_SMC_32;
+}
+
+bool __qcom_scm_pas_supported(struct device *dev, u32 peripheral)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+				QCOM_SCM_PAS_IS_SUPPORTED_CMD,
+				&desc, &res);
+
+	return ret ? false : !!res.a1;
+}
+
+int __qcom_scm_pas_init_image(struct device *dev, u32 peripheral,
+			      dma_addr_t metadata_phys)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.args[1] = metadata_phys;
+	desc.arginfo = QCOM_SCM_ARGS(2, QCOM_SCM_VAL, QCOM_SCM_RW);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_INIT_IMAGE_CMD,
+				&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_mem_setup(struct device *dev, u32 peripheral,
+			      phys_addr_t addr, phys_addr_t size)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.args[1] = addr;
+	desc.args[2] = size;
+	desc.arginfo = QCOM_SCM_ARGS(3);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_MEM_SETUP_CMD,
+				&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_auth_and_reset(struct device *dev, u32 peripheral)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+				QCOM_SCM_PAS_AUTH_AND_RESET_CMD,
+				&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_shutdown(struct device *dev, u32 peripheral)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_SHUTDOWN_CMD,
+			&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_mss_reset(struct device *dev, bool reset)
+{
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+	int ret;
+
+	desc.args[0] = reset;
+	desc.args[1] = 0;
+	desc.arginfo = QCOM_SCM_ARGS(2);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_MSS_RESET, &desc,
+			    &res);
+
+	return ret ? : res.a1;
 }
diff --git a/drivers/firmware/qcom_scm.c b/drivers/firmware/qcom_scm.c
index 45c008d..84330c5 100644
--- a/drivers/firmware/qcom_scm.c
+++ b/drivers/firmware/qcom_scm.c
@@ -10,19 +10,64 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
  */
-
+#include <linux/platform_device.h>
+#include <linux/module.h>
 #include <linux/cpumask.h>
 #include <linux/export.h>
+#include <linux/dma-mapping.h>
 #include <linux/types.h>
 #include <linux/qcom_scm.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/reset-controller.h>
 
 #include "qcom_scm.h"
 
+struct qcom_scm {
+	struct device *dev;
+	struct clk *core_clk;
+	struct clk *iface_clk;
+	struct clk *bus_clk;
+	struct reset_controller_dev reset;
+};
+
+static struct qcom_scm *__scm;
+
+static int qcom_scm_clk_enable(void)
+{
+	int ret;
+
+	ret = clk_prepare_enable(__scm->core_clk);
+	if (ret)
+		goto bail;
+
+	ret = clk_prepare_enable(__scm->iface_clk);
+	if (ret)
+		goto disable_core;
+
+	ret = clk_prepare_enable(__scm->bus_clk);
+	if (ret)
+		goto disable_iface;
+
+	return 0;
+
+disable_iface:
+	clk_disable_unprepare(__scm->iface_clk);
+disable_core:
+	clk_disable_unprepare(__scm->core_clk);
+bail:
+	return ret;
+}
+
+static void qcom_scm_clk_disable(void)
+{
+	clk_disable_unprepare(__scm->core_clk);
+	clk_disable_unprepare(__scm->iface_clk);
+	clk_disable_unprepare(__scm->bus_clk);
+}
+
 /**
  * qcom_scm_set_cold_boot_addr() - Set the cold boot address for cpus
  * @entry: Entry point function for the cpus
@@ -47,7 +92,7 @@
  */
 int qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus)
 {
-	return __qcom_scm_set_warm_boot_addr(entry, cpus);
+	return __qcom_scm_set_warm_boot_addr(__scm->dev, entry, cpus);
 }
 EXPORT_SYMBOL(qcom_scm_set_warm_boot_addr);
 
@@ -72,12 +117,17 @@
  */
 bool qcom_scm_hdcp_available(void)
 {
-	int ret;
+	int ret = qcom_scm_clk_enable();
 
-	ret = __qcom_scm_is_call_available(QCOM_SCM_SVC_HDCP,
-		QCOM_SCM_CMD_HDCP);
+	if (ret)
+		return ret;
 
-	return (ret > 0) ? true : false;
+	ret = __qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_HDCP,
+						QCOM_SCM_CMD_HDCP);
+
+	qcom_scm_clk_disable();
+
+	return ret > 0 ? true : false;
 }
 EXPORT_SYMBOL(qcom_scm_hdcp_available);
 
@@ -91,6 +141,279 @@
  */
 int qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp)
 {
-	return __qcom_scm_hdcp_req(req, req_cnt, resp);
+	int ret = qcom_scm_clk_enable();
+
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_hdcp_req(__scm->dev, req, req_cnt, resp);
+	qcom_scm_clk_disable();
+	return ret;
 }
 EXPORT_SYMBOL(qcom_scm_hdcp_req);
+
+/**
+ * qcom_scm_pas_supported() - Check if the peripheral authentication service is
+ *			      available for the given peripherial
+ * @peripheral:	peripheral id
+ *
+ * Returns true if PAS is supported for this peripheral, otherwise false.
+ */
+bool qcom_scm_pas_supported(u32 peripheral)
+{
+	int ret;
+
+	ret = __qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_PIL,
+					   QCOM_SCM_PAS_IS_SUPPORTED_CMD);
+	if (ret <= 0)
+		return false;
+
+	return __qcom_scm_pas_supported(__scm->dev, peripheral);
+}
+EXPORT_SYMBOL(qcom_scm_pas_supported);
+
+/**
+ * qcom_scm_pas_init_image() - Initialize peripheral authentication service
+ *			       state machine for a given peripheral, using the
+ *			       metadata
+ * @peripheral: peripheral id
+ * @metadata:	pointer to memory containing ELF header, program header table
+ *		and optional blob of data used for authenticating the metadata
+ *		and the rest of the firmware
+ * @size:	size of the metadata
+ *
+ * Returns 0 on success.
+ */
+int qcom_scm_pas_init_image(u32 peripheral, const void *metadata, size_t size)
+{
+	dma_addr_t mdata_phys;
+	void *mdata_buf;
+	int ret;
+
+	/*
+	 * During the scm call memory protection will be enabled for the meta
+	 * data blob, so make sure it's physically contiguous, 4K aligned and
+	 * non-cachable to avoid XPU violations.
+	 */
+	mdata_buf = dma_alloc_coherent(__scm->dev, size, &mdata_phys,
+				       GFP_KERNEL);
+	if (!mdata_buf) {
+		dev_err(__scm->dev, "Allocation of metadata buffer failed.\n");
+		return -ENOMEM;
+	}
+	memcpy(mdata_buf, metadata, size);
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		goto free_metadata;
+
+	ret = __qcom_scm_pas_init_image(__scm->dev, peripheral, mdata_phys);
+
+	qcom_scm_clk_disable();
+
+free_metadata:
+	dma_free_coherent(__scm->dev, size, mdata_buf, mdata_phys);
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_init_image);
+
+/**
+ * qcom_scm_pas_mem_setup() - Prepare the memory related to a given peripheral
+ *			      for firmware loading
+ * @peripheral:	peripheral id
+ * @addr:	start address of memory area to prepare
+ * @size:	size of the memory area to prepare
+ *
+ * Returns 0 on success.
+ */
+int qcom_scm_pas_mem_setup(u32 peripheral, phys_addr_t addr, phys_addr_t size)
+{
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_pas_mem_setup(__scm->dev, peripheral, addr, size);
+	qcom_scm_clk_disable();
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_mem_setup);
+
+/**
+ * qcom_scm_pas_auth_and_reset() - Authenticate the given peripheral firmware
+ *				   and reset the remote processor
+ * @peripheral:	peripheral id
+ *
+ * Return 0 on success.
+ */
+int qcom_scm_pas_auth_and_reset(u32 peripheral)
+{
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_pas_auth_and_reset(__scm->dev, peripheral);
+	qcom_scm_clk_disable();
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_auth_and_reset);
+
+/**
+ * qcom_scm_pas_shutdown() - Shut down the remote processor
+ * @peripheral: peripheral id
+ *
+ * Returns 0 on success.
+ */
+int qcom_scm_pas_shutdown(u32 peripheral)
+{
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_pas_shutdown(__scm->dev, peripheral);
+	qcom_scm_clk_disable();
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_shutdown);
+
+static int qcom_scm_pas_reset_assert(struct reset_controller_dev *rcdev,
+				     unsigned long idx)
+{
+	if (idx != 0)
+		return -EINVAL;
+
+	return __qcom_scm_pas_mss_reset(__scm->dev, 1);
+}
+
+static int qcom_scm_pas_reset_deassert(struct reset_controller_dev *rcdev,
+				       unsigned long idx)
+{
+	if (idx != 0)
+		return -EINVAL;
+
+	return __qcom_scm_pas_mss_reset(__scm->dev, 0);
+}
+
+static const struct reset_control_ops qcom_scm_pas_reset_ops = {
+	.assert = qcom_scm_pas_reset_assert,
+	.deassert = qcom_scm_pas_reset_deassert,
+};
+
+
+static int qcom_scm_probe(struct platform_device *pdev)
+{
+	struct qcom_scm *scm;
+	int ret;
+
+	scm = devm_kzalloc(&pdev->dev, sizeof(*scm), GFP_KERNEL);
+	if (!scm)
+		return -ENOMEM;
+
+	scm->core_clk = devm_clk_get(&pdev->dev, "core");
+	if (IS_ERR(scm->core_clk)) {
+		if (PTR_ERR(scm->core_clk) == -EPROBE_DEFER)
+			return PTR_ERR(scm->core_clk);
+
+		scm->core_clk = NULL;
+	}
+
+	if (of_device_is_compatible(pdev->dev.of_node, "qcom,scm")) {
+		scm->iface_clk = devm_clk_get(&pdev->dev, "iface");
+		if (IS_ERR(scm->iface_clk)) {
+			if (PTR_ERR(scm->iface_clk) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "failed to acquire iface clk\n");
+			return PTR_ERR(scm->iface_clk);
+		}
+
+		scm->bus_clk = devm_clk_get(&pdev->dev, "bus");
+		if (IS_ERR(scm->bus_clk)) {
+			if (PTR_ERR(scm->bus_clk) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "failed to acquire bus clk\n");
+			return PTR_ERR(scm->bus_clk);
+		}
+	}
+
+	scm->reset.ops = &qcom_scm_pas_reset_ops;
+	scm->reset.nr_resets = 1;
+	scm->reset.of_node = pdev->dev.of_node;
+	reset_controller_register(&scm->reset);
+
+	/* vote for max clk rate for highest performance */
+	ret = clk_set_rate(scm->core_clk, INT_MAX);
+	if (ret)
+		return ret;
+
+	__scm = scm;
+	__scm->dev = &pdev->dev;
+
+	__qcom_scm_init();
+
+	return 0;
+}
+
+static const struct of_device_id qcom_scm_dt_match[] = {
+	{ .compatible = "qcom,scm-apq8064",},
+	{ .compatible = "qcom,scm-msm8660",},
+	{ .compatible = "qcom,scm-msm8960",},
+	{ .compatible = "qcom,scm",},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, qcom_scm_dt_match);
+
+static struct platform_driver qcom_scm_driver = {
+	.driver = {
+		.name	= "qcom_scm",
+		.of_match_table = qcom_scm_dt_match,
+	},
+	.probe = qcom_scm_probe,
+};
+
+static int __init qcom_scm_init(void)
+{
+	struct device_node *np, *fw_np;
+	int ret;
+
+	fw_np = of_find_node_by_name(NULL, "firmware");
+
+	if (!fw_np)
+		return -ENODEV;
+
+	np = of_find_matching_node(fw_np, qcom_scm_dt_match);
+
+	if (!np) {
+		of_node_put(fw_np);
+		return -ENODEV;
+	}
+
+	of_node_put(np);
+
+	ret = of_platform_populate(fw_np, qcom_scm_dt_match, NULL, NULL);
+
+	of_node_put(fw_np);
+
+	if (ret)
+		return ret;
+
+	return platform_driver_register(&qcom_scm_driver);
+}
+
+arch_initcall(qcom_scm_init);
+
+static void __exit qcom_scm_exit(void)
+{
+	platform_driver_unregister(&qcom_scm_driver);
+}
+module_exit(qcom_scm_exit);
+
+MODULE_DESCRIPTION("Qualcomm SCM driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/firmware/qcom_scm.h b/drivers/firmware/qcom_scm.h
index 2cce75c..3584b00 100644
--- a/drivers/firmware/qcom_scm.h
+++ b/drivers/firmware/qcom_scm.h
@@ -19,7 +19,8 @@
 #define QCOM_SCM_FLAG_HLOS		0x01
 #define QCOM_SCM_FLAG_COLDBOOT_MC	0x02
 #define QCOM_SCM_FLAG_WARMBOOT_MC	0x04
-extern int __qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus);
+extern int __qcom_scm_set_warm_boot_addr(struct device *dev, void *entry,
+		const cpumask_t *cpus);
 extern int __qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus);
 
 #define QCOM_SCM_CMD_TERMINATE_PC	0x2
@@ -29,14 +30,34 @@
 
 #define QCOM_SCM_SVC_INFO		0x6
 #define QCOM_IS_CALL_AVAIL_CMD		0x1
-extern int __qcom_scm_is_call_available(u32 svc_id, u32 cmd_id);
+extern int __qcom_scm_is_call_available(struct device *dev, u32 svc_id,
+		u32 cmd_id);
 
 #define QCOM_SCM_SVC_HDCP		0x11
 #define QCOM_SCM_CMD_HDCP		0x01
-extern int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt,
-		u32 *resp);
+extern int __qcom_scm_hdcp_req(struct device *dev,
+		struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp);
+
+extern void __qcom_scm_init(void);
+
+#define QCOM_SCM_SVC_PIL		0x2
+#define QCOM_SCM_PAS_INIT_IMAGE_CMD	0x1
+#define QCOM_SCM_PAS_MEM_SETUP_CMD	0x2
+#define QCOM_SCM_PAS_AUTH_AND_RESET_CMD	0x5
+#define QCOM_SCM_PAS_SHUTDOWN_CMD	0x6
+#define QCOM_SCM_PAS_IS_SUPPORTED_CMD	0x7
+#define QCOM_SCM_PAS_MSS_RESET		0xa
+extern bool __qcom_scm_pas_supported(struct device *dev, u32 peripheral);
+extern int  __qcom_scm_pas_init_image(struct device *dev, u32 peripheral,
+		dma_addr_t metadata_phys);
+extern int  __qcom_scm_pas_mem_setup(struct device *dev, u32 peripheral,
+		phys_addr_t addr, phys_addr_t size);
+extern int  __qcom_scm_pas_auth_and_reset(struct device *dev, u32 peripheral);
+extern int  __qcom_scm_pas_shutdown(struct device *dev, u32 peripheral);
+extern int  __qcom_scm_pas_mss_reset(struct device *dev, bool reset);
 
 /* common error codes */
+#define QCOM_SCM_V2_EBUSY	-12
 #define QCOM_SCM_ENOMEM		-5
 #define QCOM_SCM_EOPNOTSUPP	-4
 #define QCOM_SCM_EINVAL_ADDR	-3
@@ -44,4 +65,22 @@
 #define QCOM_SCM_ERROR		-1
 #define QCOM_SCM_INTERRUPTED	1
 
+static inline int qcom_scm_remap_error(int err)
+{
+	switch (err) {
+	case QCOM_SCM_ERROR:
+		return -EIO;
+	case QCOM_SCM_EINVAL_ADDR:
+	case QCOM_SCM_EINVAL_ARG:
+		return -EINVAL;
+	case QCOM_SCM_EOPNOTSUPP:
+		return -EOPNOTSUPP;
+	case QCOM_SCM_ENOMEM:
+		return -ENOMEM;
+	case QCOM_SCM_V2_EBUSY:
+		return -EBUSY;
+	}
+	return -EINVAL;
+}
+
 #endif
diff --git a/drivers/firmware/scpi_pm_domain.c b/drivers/firmware/scpi_pm_domain.c
new file mode 100644
index 0000000..f395dec
--- /dev/null
+++ b/drivers/firmware/scpi_pm_domain.c
@@ -0,0 +1,163 @@
+/*
+ * SCPI Generic power domain support.
+ *
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pm_domain.h>
+#include <linux/scpi_protocol.h>
+
+struct scpi_pm_domain {
+	struct generic_pm_domain genpd;
+	struct scpi_ops *ops;
+	u32 domain;
+	char name[30];
+};
+
+/*
+ * These device power state values are not well-defined in the specification.
+ * In case, different implementations use different values, we can make these
+ * specific to compatibles rather than getting these values from device tree.
+ */
+enum scpi_power_domain_state {
+	SCPI_PD_STATE_ON = 0,
+	SCPI_PD_STATE_OFF = 3,
+};
+
+#define to_scpi_pd(gpd) container_of(gpd, struct scpi_pm_domain, genpd)
+
+static int scpi_pd_power(struct scpi_pm_domain *pd, bool power_on)
+{
+	int ret;
+	enum scpi_power_domain_state state;
+
+	if (power_on)
+		state = SCPI_PD_STATE_ON;
+	else
+		state = SCPI_PD_STATE_OFF;
+
+	ret = pd->ops->device_set_power_state(pd->domain, state);
+	if (ret)
+		return ret;
+
+	return !(state == pd->ops->device_get_power_state(pd->domain));
+}
+
+static int scpi_pd_power_on(struct generic_pm_domain *domain)
+{
+	struct scpi_pm_domain *pd = to_scpi_pd(domain);
+
+	return scpi_pd_power(pd, true);
+}
+
+static int scpi_pd_power_off(struct generic_pm_domain *domain)
+{
+	struct scpi_pm_domain *pd = to_scpi_pd(domain);
+
+	return scpi_pd_power(pd, false);
+}
+
+static int scpi_pm_domain_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct scpi_pm_domain *scpi_pd;
+	struct genpd_onecell_data *scpi_pd_data;
+	struct generic_pm_domain **domains;
+	struct scpi_ops *scpi_ops;
+	int ret, num_domains, i;
+
+	scpi_ops = get_scpi_ops();
+	if (!scpi_ops)
+		return -EPROBE_DEFER;
+
+	if (!np) {
+		dev_err(dev, "device tree node not found\n");
+		return -ENODEV;
+	}
+
+	if (!scpi_ops->device_set_power_state ||
+	    !scpi_ops->device_get_power_state) {
+		dev_err(dev, "power domains not supported in the firmware\n");
+		return -ENODEV;
+	}
+
+	ret = of_property_read_u32(np, "num-domains", &num_domains);
+	if (ret) {
+		dev_err(dev, "number of domains not found\n");
+		return -EINVAL;
+	}
+
+	scpi_pd = devm_kcalloc(dev, num_domains, sizeof(*scpi_pd), GFP_KERNEL);
+	if (!scpi_pd)
+		return -ENOMEM;
+
+	scpi_pd_data = devm_kzalloc(dev, sizeof(*scpi_pd_data), GFP_KERNEL);
+	if (!scpi_pd_data)
+		return -ENOMEM;
+
+	domains = devm_kcalloc(dev, num_domains, sizeof(*domains), GFP_KERNEL);
+	if (!domains)
+		return -ENOMEM;
+
+	for (i = 0; i < num_domains; i++, scpi_pd++) {
+		domains[i] = &scpi_pd->genpd;
+
+		scpi_pd->domain = i;
+		scpi_pd->ops = scpi_ops;
+		sprintf(scpi_pd->name, "%s.%d", np->name, i);
+		scpi_pd->genpd.name = scpi_pd->name;
+		scpi_pd->genpd.power_off = scpi_pd_power_off;
+		scpi_pd->genpd.power_on = scpi_pd_power_on;
+
+		/*
+		 * Treat all power domains as off at boot.
+		 *
+		 * The SCP firmware itself may have switched on some domains,
+		 * but for reference counting purpose, keep it this way.
+		 */
+		pm_genpd_init(&scpi_pd->genpd, NULL, true);
+	}
+
+	scpi_pd_data->domains = domains;
+	scpi_pd_data->num_domains = num_domains;
+
+	of_genpd_add_provider_onecell(np, scpi_pd_data);
+
+	return 0;
+}
+
+static const struct of_device_id scpi_power_domain_ids[] = {
+	{ .compatible = "arm,scpi-power-domains", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, scpi_power_domain_ids);
+
+static struct platform_driver scpi_power_domain_driver = {
+	.driver	= {
+		.name = "scpi_power_domain",
+		.of_match_table = scpi_power_domain_ids,
+	},
+	.probe = scpi_pm_domain_probe,
+};
+module_platform_driver(scpi_power_domain_driver);
+
+MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");
+MODULE_DESCRIPTION("ARM SCPI power domain driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/keyboard/clps711x-keypad.c b/drivers/input/keyboard/clps711x-keypad.c
index b637f1a..997e3e9 100644
--- a/drivers/input/keyboard/clps711x-keypad.c
+++ b/drivers/input/keyboard/clps711x-keypad.c
@@ -101,7 +101,7 @@
 		return -ENOMEM;
 
 	priv->syscon =
-		syscon_regmap_lookup_by_compatible("cirrus,clps711x-syscon1");
+		syscon_regmap_lookup_by_compatible("cirrus,ep7209-syscon1");
 	if (IS_ERR(priv->syscon))
 		return PTR_ERR(priv->syscon);
 
@@ -181,7 +181,7 @@
 }
 
 static const struct of_device_id clps711x_keypad_of_match[] = {
-	{ .compatible = "cirrus,clps711x-keypad", },
+	{ .compatible = "cirrus,ep7209-keypad", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, clps711x_keypad_of_match);
diff --git a/drivers/irqchip/irq-clps711x.c b/drivers/irqchip/irq-clps711x.c
index 2223b3f..f913f4d 100644
--- a/drivers/irqchip/irq-clps711x.c
+++ b/drivers/irqchip/irq-clps711x.c
@@ -234,5 +234,5 @@
 
 	return _clps711x_intc_init(np, res.start, resource_size(&res));
 }
-IRQCHIP_DECLARE(clps711x, "cirrus,clps711x-intc", clps711x_intc_init_dt);
+IRQCHIP_DECLARE(clps711x, "cirrus,ep7209-intc", clps711x_intc_init_dt);
 #endif
diff --git a/drivers/media/platform/exynos-gsc/gsc-core.c b/drivers/media/platform/exynos-gsc/gsc-core.c
index c049736..c9d2009 100644
--- a/drivers/media/platform/exynos-gsc/gsc-core.c
+++ b/drivers/media/platform/exynos-gsc/gsc-core.c
@@ -1124,6 +1124,7 @@
 		goto err_m2m;
 
 	/* Initialize continious memory allocator */
+	vb2_dma_contig_set_max_seg_size(dev, DMA_BIT_MASK(32));
 	gsc->alloc_ctx = vb2_dma_contig_init_ctx(dev);
 	if (IS_ERR(gsc->alloc_ctx)) {
 		ret = PTR_ERR(gsc->alloc_ctx);
@@ -1153,6 +1154,7 @@
 	v4l2_device_unregister(&gsc->v4l2_dev);
 
 	vb2_dma_contig_cleanup_ctx(gsc->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	gsc_clk_put(gsc);
 
diff --git a/drivers/media/platform/exynos4-is/fimc-core.c b/drivers/media/platform/exynos4-is/fimc-core.c
index b1c1cea..368f44f 100644
--- a/drivers/media/platform/exynos4-is/fimc-core.c
+++ b/drivers/media/platform/exynos4-is/fimc-core.c
@@ -1019,6 +1019,7 @@
 	}
 
 	/* Initialize contiguous memory allocator */
+	vb2_dma_contig_set_max_seg_size(dev, DMA_BIT_MASK(32));
 	fimc->alloc_ctx = vb2_dma_contig_init_ctx(dev);
 	if (IS_ERR(fimc->alloc_ctx)) {
 		ret = PTR_ERR(fimc->alloc_ctx);
@@ -1124,6 +1125,7 @@
 
 	fimc_unregister_capture_subdev(fimc);
 	vb2_dma_contig_cleanup_ctx(fimc->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(&pdev->dev);
 
 	clk_disable(fimc->clock[CLK_BUS]);
 	fimc_clk_put(fimc);
diff --git a/drivers/media/platform/exynos4-is/fimc-is.c b/drivers/media/platform/exynos4-is/fimc-is.c
index 979c388..bd98b56 100644
--- a/drivers/media/platform/exynos4-is/fimc-is.c
+++ b/drivers/media/platform/exynos4-is/fimc-is.c
@@ -847,6 +847,7 @@
 	if (ret < 0)
 		goto err_pm;
 
+	vb2_dma_contig_set_max_seg_size(dev, DMA_BIT_MASK(32));
 	is->alloc_ctx = vb2_dma_contig_init_ctx(dev);
 	if (IS_ERR(is->alloc_ctx)) {
 		ret = PTR_ERR(is->alloc_ctx);
@@ -940,6 +941,7 @@
 	free_irq(is->irq, is);
 	fimc_is_unregister_subdevs(is);
 	vb2_dma_contig_cleanup_ctx(is->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(dev);
 	fimc_is_put_clocks(is);
 	fimc_is_debugfs_remove(is);
 	release_firmware(is->fw.f_w);
diff --git a/drivers/media/platform/exynos4-is/fimc-lite.c b/drivers/media/platform/exynos4-is/fimc-lite.c
index dc1b929..27cb620 100644
--- a/drivers/media/platform/exynos4-is/fimc-lite.c
+++ b/drivers/media/platform/exynos4-is/fimc-lite.c
@@ -1551,6 +1551,7 @@
 			goto err_sd;
 	}
 
+	vb2_dma_contig_set_max_seg_size(dev, DMA_BIT_MASK(32));
 	fimc->alloc_ctx = vb2_dma_contig_init_ctx(dev);
 	if (IS_ERR(fimc->alloc_ctx)) {
 		ret = PTR_ERR(fimc->alloc_ctx);
@@ -1652,6 +1653,7 @@
 	pm_runtime_set_suspended(dev);
 	fimc_lite_unregister_capture_subdev(fimc);
 	vb2_dma_contig_cleanup_ctx(fimc->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(dev);
 	fimc_lite_clk_put(fimc);
 
 	dev_info(dev, "Driver unloaded\n");
diff --git a/drivers/media/platform/s5p-g2d/g2d.c b/drivers/media/platform/s5p-g2d/g2d.c
index 612d1ea..d3e3469 100644
--- a/drivers/media/platform/s5p-g2d/g2d.c
+++ b/drivers/media/platform/s5p-g2d/g2d.c
@@ -681,6 +681,7 @@
 		goto put_clk_gate;
 	}
 
+	vb2_dma_contig_set_max_seg_size(&pdev->dev, DMA_BIT_MASK(32));
 	dev->alloc_ctx = vb2_dma_contig_init_ctx(&pdev->dev);
 	if (IS_ERR(dev->alloc_ctx)) {
 		ret = PTR_ERR(dev->alloc_ctx);
@@ -757,6 +758,7 @@
 	video_unregister_device(dev->vfd);
 	v4l2_device_unregister(&dev->v4l2_dev);
 	vb2_dma_contig_cleanup_ctx(dev->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(&pdev->dev);
 	clk_unprepare(dev->gate);
 	clk_put(dev->gate);
 	clk_unprepare(dev->clk);
diff --git a/drivers/media/platform/s5p-jpeg/jpeg-core.c b/drivers/media/platform/s5p-jpeg/jpeg-core.c
index caa19b4..17bc94092 100644
--- a/drivers/media/platform/s5p-jpeg/jpeg-core.c
+++ b/drivers/media/platform/s5p-jpeg/jpeg-core.c
@@ -2843,6 +2843,7 @@
 		goto device_register_rollback;
 	}
 
+	vb2_dma_contig_set_max_seg_size(&pdev->dev, DMA_BIT_MASK(32));
 	jpeg->alloc_ctx = vb2_dma_contig_init_ctx(&pdev->dev);
 	if (IS_ERR(jpeg->alloc_ctx)) {
 		v4l2_err(&jpeg->v4l2_dev, "Failed to init memory allocator\n");
@@ -2942,6 +2943,7 @@
 	video_unregister_device(jpeg->vfd_decoder);
 	video_unregister_device(jpeg->vfd_encoder);
 	vb2_dma_contig_cleanup_ctx(jpeg->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(&pdev->dev);
 	v4l2_m2m_release(jpeg->m2m_dev);
 	v4l2_device_unregister(&jpeg->v4l2_dev);
 
diff --git a/drivers/media/platform/s5p-mfc/s5p_mfc.c b/drivers/media/platform/s5p-mfc/s5p_mfc.c
index b16466f..6ee620e 100644
--- a/drivers/media/platform/s5p-mfc/s5p_mfc.c
+++ b/drivers/media/platform/s5p-mfc/s5p_mfc.c
@@ -22,6 +22,7 @@
 #include <media/v4l2-event.h>
 #include <linux/workqueue.h>
 #include <linux/of.h>
+#include <linux/of_reserved_mem.h>
 #include <media/videobuf2-v4l2.h>
 #include "s5p_mfc_common.h"
 #include "s5p_mfc_ctrl.h"
@@ -29,6 +30,7 @@
 #include "s5p_mfc_dec.h"
 #include "s5p_mfc_enc.h"
 #include "s5p_mfc_intr.h"
+#include "s5p_mfc_iommu.h"
 #include "s5p_mfc_opr.h"
 #include "s5p_mfc_cmd.h"
 #include "s5p_mfc_pm.h"
@@ -1043,55 +1045,94 @@
 	.mmap = s5p_mfc_mmap,
 };
 
-static int match_child(struct device *dev, void *data)
+/* DMA memory related helper functions */
+static void s5p_mfc_memdev_release(struct device *dev)
 {
-	if (!dev_name(dev))
-		return 0;
-	return !strcmp(dev_name(dev), (char *)data);
+	of_reserved_mem_device_release(dev);
+}
+
+static struct device *s5p_mfc_alloc_memdev(struct device *dev,
+					   const char *name, unsigned int idx)
+{
+	struct device *child;
+	int ret;
+
+	child = devm_kzalloc(dev, sizeof(struct device), GFP_KERNEL);
+	if (!child)
+		return NULL;
+
+	device_initialize(child);
+	dev_set_name(child, "%s:%s", dev_name(dev), name);
+	child->parent = dev;
+	child->bus = dev->bus;
+	child->coherent_dma_mask = dev->coherent_dma_mask;
+	child->dma_mask = dev->dma_mask;
+	child->release = s5p_mfc_memdev_release;
+
+	if (device_add(child) == 0) {
+		ret = of_reserved_mem_device_init_by_idx(child, dev->of_node,
+							 idx);
+		if (ret == 0)
+			return child;
+	}
+
+	put_device(child);
+	return NULL;
+}
+
+static int s5p_mfc_configure_dma_memory(struct s5p_mfc_dev *mfc_dev)
+{
+	struct device *dev = &mfc_dev->plat_dev->dev;
+
+	/*
+	 * When IOMMU is available, we cannot use the default configuration,
+	 * because of MFC firmware requirements: address space limited to
+	 * 256M and non-zero default start address.
+	 * This is still simplified, not optimal configuration, but for now
+	 * IOMMU core doesn't allow to configure device's IOMMUs channel
+	 * separately.
+	 */
+	if (exynos_is_iommu_available(dev)) {
+		int ret = exynos_configure_iommu(dev, S5P_MFC_IOMMU_DMA_BASE,
+						 S5P_MFC_IOMMU_DMA_SIZE);
+		if (ret == 0)
+			mfc_dev->mem_dev_l = mfc_dev->mem_dev_r = dev;
+		return ret;
+	}
+
+	/*
+	 * Create and initialize virtual devices for accessing
+	 * reserved memory regions.
+	 */
+	mfc_dev->mem_dev_l = s5p_mfc_alloc_memdev(dev, "left",
+						  MFC_BANK1_ALLOC_CTX);
+	if (!mfc_dev->mem_dev_l)
+		return -ENODEV;
+	mfc_dev->mem_dev_r = s5p_mfc_alloc_memdev(dev, "right",
+						  MFC_BANK2_ALLOC_CTX);
+	if (!mfc_dev->mem_dev_r) {
+		device_unregister(mfc_dev->mem_dev_l);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static void s5p_mfc_unconfigure_dma_memory(struct s5p_mfc_dev *mfc_dev)
+{
+	struct device *dev = &mfc_dev->plat_dev->dev;
+
+	if (exynos_is_iommu_available(dev)) {
+		exynos_unconfigure_iommu(dev);
+		return;
+	}
+
+	device_unregister(mfc_dev->mem_dev_l);
+	device_unregister(mfc_dev->mem_dev_r);
 }
 
 static void *mfc_get_drv_data(struct platform_device *pdev);
 
-static int s5p_mfc_alloc_memdevs(struct s5p_mfc_dev *dev)
-{
-	unsigned int mem_info[2] = { };
-
-	dev->mem_dev_l = devm_kzalloc(&dev->plat_dev->dev,
-			sizeof(struct device), GFP_KERNEL);
-	if (!dev->mem_dev_l) {
-		mfc_err("Not enough memory\n");
-		return -ENOMEM;
-	}
-	device_initialize(dev->mem_dev_l);
-	of_property_read_u32_array(dev->plat_dev->dev.of_node,
-			"samsung,mfc-l", mem_info, 2);
-	if (dma_declare_coherent_memory(dev->mem_dev_l, mem_info[0],
-				mem_info[0], mem_info[1],
-				DMA_MEMORY_MAP | DMA_MEMORY_EXCLUSIVE) == 0) {
-		mfc_err("Failed to declare coherent memory for\n"
-		"MFC device\n");
-		return -ENOMEM;
-	}
-
-	dev->mem_dev_r = devm_kzalloc(&dev->plat_dev->dev,
-			sizeof(struct device), GFP_KERNEL);
-	if (!dev->mem_dev_r) {
-		mfc_err("Not enough memory\n");
-		return -ENOMEM;
-	}
-	device_initialize(dev->mem_dev_r);
-	of_property_read_u32_array(dev->plat_dev->dev.of_node,
-			"samsung,mfc-r", mem_info, 2);
-	if (dma_declare_coherent_memory(dev->mem_dev_r, mem_info[0],
-				mem_info[0], mem_info[1],
-				DMA_MEMORY_MAP | DMA_MEMORY_EXCLUSIVE) == 0) {
-		pr_err("Failed to declare coherent memory for\n"
-		"MFC device\n");
-		return -ENOMEM;
-	}
-	return 0;
-}
-
 /* MFC probe function */
 static int s5p_mfc_probe(struct platform_device *pdev)
 {
@@ -1117,12 +1158,6 @@
 
 	dev->variant = mfc_get_drv_data(pdev);
 
-	ret = s5p_mfc_init_pm(dev);
-	if (ret < 0) {
-		dev_err(&pdev->dev, "failed to get mfc clock source\n");
-		return ret;
-	}
-
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
 	dev->regs_base = devm_ioremap_resource(&pdev->dev, res);
@@ -1143,32 +1178,25 @@
 		goto err_res;
 	}
 
-	if (pdev->dev.of_node) {
-		ret = s5p_mfc_alloc_memdevs(dev);
-		if (ret < 0)
-			goto err_res;
-	} else {
-		dev->mem_dev_l = device_find_child(&dev->plat_dev->dev,
-				"s5p-mfc-l", match_child);
-		if (!dev->mem_dev_l) {
-			mfc_err("Mem child (L) device get failed\n");
-			ret = -ENODEV;
-			goto err_res;
-		}
-		dev->mem_dev_r = device_find_child(&dev->plat_dev->dev,
-				"s5p-mfc-r", match_child);
-		if (!dev->mem_dev_r) {
-			mfc_err("Mem child (R) device get failed\n");
-			ret = -ENODEV;
-			goto err_res;
-		}
+	ret = s5p_mfc_configure_dma_memory(dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to configure DMA memory\n");
+		return ret;
 	}
 
+	ret = s5p_mfc_init_pm(dev);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to get mfc clock source\n");
+		return ret;
+	}
+
+	vb2_dma_contig_set_max_seg_size(dev->mem_dev_l, DMA_BIT_MASK(32));
 	dev->alloc_ctx[0] = vb2_dma_contig_init_ctx(dev->mem_dev_l);
 	if (IS_ERR(dev->alloc_ctx[0])) {
 		ret = PTR_ERR(dev->alloc_ctx[0]);
 		goto err_res;
 	}
+	vb2_dma_contig_set_max_seg_size(dev->mem_dev_r, DMA_BIT_MASK(32));
 	dev->alloc_ctx[1] = vb2_dma_contig_init_ctx(dev->mem_dev_r);
 	if (IS_ERR(dev->alloc_ctx[1])) {
 		ret = PTR_ERR(dev->alloc_ctx[1]);
@@ -1201,14 +1229,6 @@
 	vfd->vfl_dir	= VFL_DIR_M2M;
 	snprintf(vfd->name, sizeof(vfd->name), "%s", S5P_MFC_DEC_NAME);
 	dev->vfd_dec	= vfd;
-	ret = video_register_device(vfd, VFL_TYPE_GRABBER, 0);
-	if (ret) {
-		v4l2_err(&dev->v4l2_dev, "Failed to register video device\n");
-		video_device_release(vfd);
-		goto err_dec_reg;
-	}
-	v4l2_info(&dev->v4l2_dev,
-		  "decoder registered as /dev/video%d\n", vfd->num);
 	video_set_drvdata(vfd, dev);
 
 	/* encoder */
@@ -1226,14 +1246,6 @@
 	vfd->vfl_dir	= VFL_DIR_M2M;
 	snprintf(vfd->name, sizeof(vfd->name), "%s", S5P_MFC_ENC_NAME);
 	dev->vfd_enc	= vfd;
-	ret = video_register_device(vfd, VFL_TYPE_GRABBER, 0);
-	if (ret) {
-		v4l2_err(&dev->v4l2_dev, "Failed to register video device\n");
-		video_device_release(vfd);
-		goto err_enc_reg;
-	}
-	v4l2_info(&dev->v4l2_dev,
-		  "encoder registered as /dev/video%d\n", vfd->num);
 	video_set_drvdata(vfd, dev);
 	platform_set_drvdata(pdev, dev);
 
@@ -1250,15 +1262,34 @@
 	s5p_mfc_init_hw_cmds(dev);
 	s5p_mfc_init_regs(dev);
 
+	/* Register decoder and encoder */
+	ret = video_register_device(dev->vfd_dec, VFL_TYPE_GRABBER, 0);
+	if (ret) {
+		v4l2_err(&dev->v4l2_dev, "Failed to register video device\n");
+		video_device_release(dev->vfd_dec);
+		goto err_dec_reg;
+	}
+	v4l2_info(&dev->v4l2_dev,
+		  "decoder registered as /dev/video%d\n", dev->vfd_dec->num);
+
+	ret = video_register_device(dev->vfd_enc, VFL_TYPE_GRABBER, 0);
+	if (ret) {
+		v4l2_err(&dev->v4l2_dev, "Failed to register video device\n");
+		video_device_release(dev->vfd_enc);
+		goto err_enc_reg;
+	}
+	v4l2_info(&dev->v4l2_dev,
+		  "encoder registered as /dev/video%d\n", dev->vfd_enc->num);
+
 	pr_debug("%s--\n", __func__);
 	return 0;
 
 /* Deinit MFC if probe had failed */
 err_enc_reg:
-	video_device_release(dev->vfd_enc);
-err_enc_alloc:
 	video_unregister_device(dev->vfd_dec);
 err_dec_reg:
+	video_device_release(dev->vfd_enc);
+err_enc_alloc:
 	video_device_release(dev->vfd_dec);
 err_dec_alloc:
 	v4l2_device_unregister(&dev->v4l2_dev);
@@ -1293,10 +1324,9 @@
 	s5p_mfc_release_firmware(dev);
 	vb2_dma_contig_cleanup_ctx(dev->alloc_ctx[0]);
 	vb2_dma_contig_cleanup_ctx(dev->alloc_ctx[1]);
-	if (pdev->dev.of_node) {
-		put_device(dev->mem_dev_l);
-		put_device(dev->mem_dev_r);
-	}
+	s5p_mfc_unconfigure_dma_memory(dev);
+	vb2_dma_contig_clear_max_seg_size(dev->mem_dev_l);
+	vb2_dma_contig_clear_max_seg_size(dev->mem_dev_r);
 
 	s5p_mfc_final_pm(dev);
 	return 0;
diff --git a/drivers/media/platform/s5p-mfc/s5p_mfc_iommu.h b/drivers/media/platform/s5p-mfc/s5p_mfc_iommu.h
new file mode 100644
index 0000000..5d1d1c2
--- /dev/null
+++ b/drivers/media/platform/s5p-mfc/s5p_mfc_iommu.h
@@ -0,0 +1,79 @@
+/*
+ * Copyright (C) 2015 Samsung Electronics Co.Ltd
+ * Authors: Marek Szyprowski <m.szyprowski@samsung.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef S5P_MFC_IOMMU_H_
+#define S5P_MFC_IOMMU_H_
+
+#define S5P_MFC_IOMMU_DMA_BASE	0x20000000lu
+#define S5P_MFC_IOMMU_DMA_SIZE	SZ_256M
+
+#ifdef CONFIG_EXYNOS_IOMMU
+
+#include <asm/dma-iommu.h>
+
+static inline bool exynos_is_iommu_available(struct device *dev)
+{
+	return dev->archdata.iommu != NULL;
+}
+
+static inline void exynos_unconfigure_iommu(struct device *dev)
+{
+	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
+
+	arm_iommu_detach_device(dev);
+	arm_iommu_release_mapping(mapping);
+}
+
+static inline int exynos_configure_iommu(struct device *dev,
+					 unsigned int base, unsigned int size)
+{
+	struct dma_iommu_mapping *mapping = NULL;
+	int ret;
+
+	/* Disable the default mapping created by device core */
+	if (to_dma_iommu_mapping(dev))
+		exynos_unconfigure_iommu(dev);
+
+	mapping = arm_iommu_create_mapping(dev->bus, base, size);
+	if (IS_ERR(mapping)) {
+		pr_warn("Failed to create IOMMU mapping for device %s\n",
+			dev_name(dev));
+		return PTR_ERR(mapping);
+	}
+
+	ret = arm_iommu_attach_device(dev, mapping);
+	if (ret) {
+		pr_warn("Failed to attached device %s to IOMMU_mapping\n",
+				dev_name(dev));
+		arm_iommu_release_mapping(mapping);
+		return ret;
+	}
+
+	return 0;
+}
+
+#else
+
+static inline bool exynos_is_iommu_available(struct device *dev)
+{
+	return false;
+}
+
+static inline int exynos_configure_iommu(struct device *dev,
+					 unsigned int base, unsigned int size)
+{
+	return -ENOSYS;
+}
+
+static inline void exynos_unconfigure_iommu(struct device *dev) { }
+
+#endif
+
+#endif /* S5P_MFC_IOMMU_H_ */
diff --git a/drivers/media/platform/s5p-tv/mixer_video.c b/drivers/media/platform/s5p-tv/mixer_video.c
index 7ab5578..123d271 100644
--- a/drivers/media/platform/s5p-tv/mixer_video.c
+++ b/drivers/media/platform/s5p-tv/mixer_video.c
@@ -80,6 +80,7 @@
 		goto fail;
 	}
 
+	vb2_dma_contig_set_max_seg_size(mdev->dev, DMA_BIT_MASK(32));
 	mdev->alloc_ctx = vb2_dma_contig_init_ctx(mdev->dev);
 	if (IS_ERR(mdev->alloc_ctx)) {
 		mxr_err(mdev, "could not acquire vb2 allocator\n");
@@ -152,6 +153,7 @@
 		kfree(mdev->output[i]);
 
 	vb2_dma_contig_cleanup_ctx(mdev->alloc_ctx);
+	vb2_dma_contig_clear_max_seg_size(mdev->dev);
 	v4l2_device_unregister(&mdev->v4l2_dev);
 }
 
diff --git a/drivers/media/v4l2-core/videobuf2-dma-contig.c b/drivers/media/v4l2-core/videobuf2-dma-contig.c
index 5361197..e3e47ac 100644
--- a/drivers/media/v4l2-core/videobuf2-dma-contig.c
+++ b/drivers/media/v4l2-core/videobuf2-dma-contig.c
@@ -753,6 +753,59 @@
 }
 EXPORT_SYMBOL_GPL(vb2_dma_contig_cleanup_ctx);
 
+/**
+ * vb2_dma_contig_set_max_seg_size() - configure DMA max segment size
+ * @dev:	device for configuring DMA parameters
+ * @size:	size of DMA max segment size to set
+ *
+ * To allow mapping the scatter-list into a single chunk in the DMA
+ * address space, the device is required to have the DMA max segment
+ * size parameter set to a value larger than the buffer size. Otherwise,
+ * the DMA-mapping subsystem will split the mapping into max segment
+ * size chunks. This function sets the DMA max segment size
+ * parameter to let DMA-mapping map a buffer as a single chunk in DMA
+ * address space.
+ * This code assumes that the DMA-mapping subsystem will merge all
+ * scatterlist segments if this is really possible (for example when
+ * an IOMMU is available and enabled).
+ * Ideally, this parameter should be set by the generic bus code, but it
+ * is left with the default 64KiB value due to historical litmiations in
+ * other subsystems (like limited USB host drivers) and there no good
+ * place to set it to the proper value.
+ * This function should be called from the drivers, which are known to
+ * operate on platforms with IOMMU and provide access to shared buffers
+ * (either USERPTR or DMABUF). This should be done before initializing
+ * videobuf2 queue.
+ */
+int vb2_dma_contig_set_max_seg_size(struct device *dev, unsigned int size)
+{
+	if (!dev->dma_parms) {
+		dev->dma_parms = kzalloc(sizeof(dev->dma_parms), GFP_KERNEL);
+		if (!dev->dma_parms)
+			return -ENOMEM;
+	}
+	if (dma_get_max_seg_size(dev) < size)
+		return dma_set_max_seg_size(dev, size);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(vb2_dma_contig_set_max_seg_size);
+
+/*
+ * vb2_dma_contig_clear_max_seg_size() - release resources for DMA parameters
+ * @dev:	device for configuring DMA parameters
+ *
+ * This function releases resources allocated to configure DMA parameters
+ * (see vb2_dma_contig_set_max_seg_size() function). It should be called from
+ * device drivers on driver remove.
+ */
+void vb2_dma_contig_clear_max_seg_size(struct device *dev)
+{
+	kfree(dev->dma_parms);
+	dev->dma_parms = NULL;
+}
+EXPORT_SYMBOL_GPL(vb2_dma_contig_clear_max_seg_size);
+
 MODULE_DESCRIPTION("DMA-contig memory handling routines for videobuf2");
 MODULE_AUTHOR("Pawel Osciak <pawel@osciak.com>");
 MODULE_LICENSE("GPL");
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 81ddb17..1337123 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -25,6 +25,17 @@
 	  Starting with the at91sam9g45, this controller supports SDR, DDR and
 	  LP-DDR memories.
 
+config ATMEL_EBI
+	bool "Atmel EBI driver"
+	default y
+	depends on ARCH_AT91 && OF
+	select MFD_SYSCON
+	help
+	  Driver for Atmel EBI controller.
+	  Used to configure the EBI (external bus interface) when the device-
+	  tree is used. This bus supports NANDs, external ethernet controller,
+	  SRAMs, ATA devices, etc.
+
 config TI_AEMIF
 	tristate "Texas Instruments AEMIF driver"
 	depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index cb0b7a1..b20ae38 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -7,6 +7,7 @@
 endif
 obj-$(CONFIG_ARM_PL172_MPMC)	+= pl172.o
 obj-$(CONFIG_ATMEL_SDRAMC)	+= atmel-sdramc.o
+obj-$(CONFIG_ATMEL_EBI)		+= atmel-ebi.o
 obj-$(CONFIG_TI_AEMIF)		+= ti-aemif.o
 obj-$(CONFIG_TI_EMIF)		+= emif.o
 obj-$(CONFIG_OMAP_GPMC)		+= omap-gpmc.o
diff --git a/drivers/memory/atmel-ebi.c b/drivers/memory/atmel-ebi.c
new file mode 100644
index 0000000..f87ad6f
--- /dev/null
+++ b/drivers/memory/atmel-ebi.c
@@ -0,0 +1,766 @@
+/*
+ * EBI driver for Atmel chips
+ * inspired by the fsl weim bus driver
+ *
+ * Copyright (C) 2013 Jean-Jacques Hiblot <jjhiblot@traphandler.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/mfd/syscon.h>
+#include <linux/mfd/syscon/atmel-matrix.h>
+#include <linux/mfd/syscon/atmel-smc.h>
+#include <linux/init.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+struct at91sam9_smc_timings {
+	u32 ncs_rd_setup_ns;
+	u32 nrd_setup_ns;
+	u32 ncs_wr_setup_ns;
+	u32 nwe_setup_ns;
+	u32 ncs_rd_pulse_ns;
+	u32 nrd_pulse_ns;
+	u32 ncs_wr_pulse_ns;
+	u32 nwe_pulse_ns;
+	u32 nrd_cycle_ns;
+	u32 nwe_cycle_ns;
+	u32 tdf_ns;
+};
+
+struct at91sam9_smc_generic_fields {
+	struct regmap_field *setup;
+	struct regmap_field *pulse;
+	struct regmap_field *cycle;
+	struct regmap_field *mode;
+};
+
+struct at91sam9_ebi_dev_config {
+	struct at91sam9_smc_timings timings;
+	u32 mode;
+};
+
+struct at91_ebi_dev_config {
+	int cs;
+	union {
+		struct at91sam9_ebi_dev_config sam9;
+	};
+};
+
+struct at91_ebi;
+
+struct at91_ebi_dev {
+	struct list_head node;
+	struct at91_ebi *ebi;
+	u32 mode;
+	int numcs;
+	struct at91_ebi_dev_config configs[];
+};
+
+struct at91_ebi_caps {
+	unsigned int available_cs;
+	const struct reg_field *ebi_csa;
+	void (*get_config)(struct at91_ebi_dev *ebid,
+			   struct at91_ebi_dev_config *conf);
+	int (*xlate_config)(struct at91_ebi_dev *ebid,
+			    struct device_node *configs_np,
+			    struct at91_ebi_dev_config *conf);
+	int (*apply_config)(struct at91_ebi_dev *ebid,
+			    struct at91_ebi_dev_config *conf);
+	int (*init)(struct at91_ebi *ebi);
+};
+
+struct at91_ebi {
+	struct clk *clk;
+	struct regmap *smc;
+	struct regmap *matrix;
+
+	struct regmap_field *ebi_csa;
+
+	struct device *dev;
+	const struct at91_ebi_caps *caps;
+	struct list_head devs;
+	union {
+		struct at91sam9_smc_generic_fields sam9;
+	};
+};
+
+static void at91sam9_ebi_get_config(struct at91_ebi_dev *ebid,
+				    struct at91_ebi_dev_config *conf)
+{
+	struct at91sam9_smc_generic_fields *fields = &ebid->ebi->sam9;
+	unsigned int clk_rate = clk_get_rate(ebid->ebi->clk);
+	struct at91sam9_ebi_dev_config *config = &conf->sam9;
+	struct at91sam9_smc_timings *timings = &config->timings;
+	unsigned int val;
+
+	regmap_fields_read(fields->mode, conf->cs, &val);
+	config->mode = val & ~AT91_SMC_TDF;
+
+	val = (val & AT91_SMC_TDF) >> 16;
+	timings->tdf_ns = clk_rate * val;
+
+	regmap_fields_read(fields->setup, conf->cs, &val);
+	timings->ncs_rd_setup_ns = (val >> 24) & 0x1f;
+	timings->ncs_rd_setup_ns += ((val >> 29) & 0x1) * 128;
+	timings->ncs_rd_setup_ns *= clk_rate;
+	timings->nrd_setup_ns = (val >> 16) & 0x1f;
+	timings->nrd_setup_ns += ((val >> 21) & 0x1) * 128;
+	timings->nrd_setup_ns *= clk_rate;
+	timings->ncs_wr_setup_ns = (val >> 8) & 0x1f;
+	timings->ncs_wr_setup_ns += ((val >> 13) & 0x1) * 128;
+	timings->ncs_wr_setup_ns *= clk_rate;
+	timings->nwe_setup_ns = val & 0x1f;
+	timings->nwe_setup_ns += ((val >> 5) & 0x1) * 128;
+	timings->nwe_setup_ns *= clk_rate;
+
+	regmap_fields_read(fields->pulse, conf->cs, &val);
+	timings->ncs_rd_pulse_ns = (val >> 24) & 0x3f;
+	timings->ncs_rd_pulse_ns += ((val >> 30) & 0x1) * 256;
+	timings->ncs_rd_pulse_ns *= clk_rate;
+	timings->nrd_pulse_ns = (val >> 16) & 0x3f;
+	timings->nrd_pulse_ns += ((val >> 22) & 0x1) * 256;
+	timings->nrd_pulse_ns *= clk_rate;
+	timings->ncs_wr_pulse_ns = (val >> 8) & 0x3f;
+	timings->ncs_wr_pulse_ns += ((val >> 14) & 0x1) * 256;
+	timings->ncs_wr_pulse_ns *= clk_rate;
+	timings->nwe_pulse_ns = val & 0x3f;
+	timings->nwe_pulse_ns += ((val >> 6) & 0x1) * 256;
+	timings->nwe_pulse_ns *= clk_rate;
+
+	regmap_fields_read(fields->cycle, conf->cs, &val);
+	timings->nrd_cycle_ns = (val >> 16) & 0x7f;
+	timings->nrd_cycle_ns += ((val >> 23) & 0x3) * 256;
+	timings->nrd_cycle_ns *= clk_rate;
+	timings->nwe_cycle_ns = val & 0x7f;
+	timings->nwe_cycle_ns += ((val >> 7) & 0x3) * 256;
+	timings->nwe_cycle_ns *= clk_rate;
+}
+
+static int at91_xlate_timing(struct device_node *np, const char *prop,
+			     u32 *val, bool *required)
+{
+	if (!of_property_read_u32(np, prop, val)) {
+		*required = true;
+		return 0;
+	}
+
+	if (*required)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int at91sam9_smc_xslate_timings(struct at91_ebi_dev *ebid,
+				       struct device_node *np,
+				       struct at91sam9_smc_timings *timings,
+				       bool *required)
+{
+	int ret;
+
+	ret = at91_xlate_timing(np, "atmel,smc-ncs-rd-setup-ns",
+				&timings->ncs_rd_setup_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-nrd-setup-ns",
+				&timings->nrd_setup_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-ncs-wr-setup-ns",
+				&timings->ncs_wr_setup_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-nwe-setup-ns",
+				&timings->nwe_setup_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-ncs-rd-pulse-ns",
+				&timings->ncs_rd_pulse_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-nrd-pulse-ns",
+				&timings->nrd_pulse_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-ncs-wr-pulse-ns",
+				&timings->ncs_wr_pulse_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-nwe-pulse-ns",
+				&timings->nwe_pulse_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-nwe-cycle-ns",
+				&timings->nwe_cycle_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-nrd-cycle-ns",
+				&timings->nrd_cycle_ns, required);
+	if (ret)
+		goto out;
+
+	ret = at91_xlate_timing(np, "atmel,smc-tdf-ns",
+				&timings->tdf_ns, required);
+
+out:
+	if (ret)
+		dev_err(ebid->ebi->dev,
+			"missing or invalid timings definition in %s",
+			np->full_name);
+
+	return ret;
+}
+
+static int at91sam9_ebi_xslate_config(struct at91_ebi_dev *ebid,
+				      struct device_node *np,
+				      struct at91_ebi_dev_config *conf)
+{
+	struct at91sam9_ebi_dev_config *config = &conf->sam9;
+	bool required = false;
+	const char *tmp_str;
+	u32 tmp;
+	int ret;
+
+	ret = of_property_read_u32(np, "atmel,smc-bus-width", &tmp);
+	if (!ret) {
+		switch (tmp) {
+		case 8:
+			config->mode |= AT91_SMC_DBW_8;
+			break;
+
+		case 16:
+			config->mode |= AT91_SMC_DBW_16;
+			break;
+
+		case 32:
+			config->mode |= AT91_SMC_DBW_32;
+			break;
+
+		default:
+			return -EINVAL;
+		}
+
+		required = true;
+	}
+
+	if (of_property_read_bool(np, "atmel,smc-tdf-optimized")) {
+		config->mode |= AT91_SMC_TDFMODE_OPTIMIZED;
+		required = true;
+	}
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,smc-byte-access-type", &tmp_str);
+	if (tmp_str && !strcmp(tmp_str, "write")) {
+		config->mode |= AT91_SMC_BAT_WRITE;
+		required = true;
+	}
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,smc-read-mode", &tmp_str);
+	if (tmp_str && !strcmp(tmp_str, "nrd")) {
+		config->mode |= AT91_SMC_READMODE_NRD;
+		required = true;
+	}
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,smc-write-mode", &tmp_str);
+	if (tmp_str && !strcmp(tmp_str, "nwe")) {
+		config->mode |= AT91_SMC_WRITEMODE_NWE;
+		required = true;
+	}
+
+	tmp_str = NULL;
+	of_property_read_string(np, "atmel,smc-exnw-mode", &tmp_str);
+	if (tmp_str) {
+		if (!strcmp(tmp_str, "frozen"))
+			config->mode |= AT91_SMC_EXNWMODE_FROZEN;
+		else if (!strcmp(tmp_str, "ready"))
+			config->mode |= AT91_SMC_EXNWMODE_READY;
+		else if (strcmp(tmp_str, "disabled"))
+			return -EINVAL;
+
+		required = true;
+	}
+
+	ret = of_property_read_u32(np, "atmel,smc-page-mode", &tmp);
+	if (!ret) {
+		switch (tmp) {
+		case 4:
+			config->mode |= AT91_SMC_PS_4;
+			break;
+
+		case 8:
+			config->mode |= AT91_SMC_PS_8;
+			break;
+
+		case 16:
+			config->mode |= AT91_SMC_PS_16;
+			break;
+
+		case 32:
+			config->mode |= AT91_SMC_PS_32;
+			break;
+
+		default:
+			return -EINVAL;
+		}
+
+		config->mode |= AT91_SMC_PMEN;
+		required = true;
+	}
+
+	ret = at91sam9_smc_xslate_timings(ebid, np, &config->timings,
+					  &required);
+	if (ret)
+		return ret;
+
+	return required;
+}
+
+static int at91sam9_ebi_apply_config(struct at91_ebi_dev *ebid,
+				     struct at91_ebi_dev_config *conf)
+{
+	unsigned int clk_rate = clk_get_rate(ebid->ebi->clk);
+	struct at91sam9_ebi_dev_config *config = &conf->sam9;
+	struct at91sam9_smc_timings *timings = &config->timings;
+	struct at91sam9_smc_generic_fields *fields = &ebid->ebi->sam9;
+	u32 coded_val;
+	u32 val;
+
+	coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+						    timings->ncs_rd_setup_ns);
+	val = AT91SAM9_SMC_NCS_NRDSETUP(coded_val);
+	coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+						    timings->nrd_setup_ns);
+	val |= AT91SAM9_SMC_NRDSETUP(coded_val);
+	coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+						    timings->ncs_wr_setup_ns);
+	val |= AT91SAM9_SMC_NCS_WRSETUP(coded_val);
+	coded_val = at91sam9_smc_setup_ns_to_cycles(clk_rate,
+						    timings->nwe_setup_ns);
+	val |= AT91SAM9_SMC_NWESETUP(coded_val);
+	regmap_fields_write(fields->setup, conf->cs, val);
+
+	coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+						    timings->ncs_rd_pulse_ns);
+	val = AT91SAM9_SMC_NCS_NRDPULSE(coded_val);
+	coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+						    timings->nrd_pulse_ns);
+	val |= AT91SAM9_SMC_NRDPULSE(coded_val);
+	coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+						    timings->ncs_wr_pulse_ns);
+	val |= AT91SAM9_SMC_NCS_WRPULSE(coded_val);
+	coded_val = at91sam9_smc_pulse_ns_to_cycles(clk_rate,
+						    timings->nwe_pulse_ns);
+	val |= AT91SAM9_SMC_NWEPULSE(coded_val);
+	regmap_fields_write(fields->pulse, conf->cs, val);
+
+	coded_val = at91sam9_smc_cycle_ns_to_cycles(clk_rate,
+						    timings->nrd_cycle_ns);
+	val = AT91SAM9_SMC_NRDCYCLE(coded_val);
+	coded_val = at91sam9_smc_cycle_ns_to_cycles(clk_rate,
+						    timings->nwe_cycle_ns);
+	val |= AT91SAM9_SMC_NWECYCLE(coded_val);
+	regmap_fields_write(fields->cycle, conf->cs, val);
+
+	val = DIV_ROUND_UP(timings->tdf_ns, clk_rate);
+	if (val > AT91_SMC_TDF_MAX)
+		val = AT91_SMC_TDF_MAX;
+	regmap_fields_write(fields->mode, conf->cs,
+			    config->mode | AT91_SMC_TDF_(val));
+
+	return 0;
+}
+
+static int at91sam9_ebi_init(struct at91_ebi *ebi)
+{
+	struct at91sam9_smc_generic_fields *fields = &ebi->sam9;
+	struct reg_field field = REG_FIELD(0, 0, 31);
+
+	field.id_size = fls(ebi->caps->available_cs);
+	field.id_offset = AT91SAM9_SMC_GENERIC_BLK_SZ;
+
+	field.reg = AT91SAM9_SMC_SETUP(AT91SAM9_SMC_GENERIC);
+	fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->setup))
+		return PTR_ERR(fields->setup);
+
+	field.reg = AT91SAM9_SMC_PULSE(AT91SAM9_SMC_GENERIC);
+	fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->pulse))
+		return PTR_ERR(fields->pulse);
+
+	field.reg = AT91SAM9_SMC_CYCLE(AT91SAM9_SMC_GENERIC);
+	fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->cycle))
+		return PTR_ERR(fields->cycle);
+
+	field.reg = AT91SAM9_SMC_MODE(AT91SAM9_SMC_GENERIC);
+	fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->mode))
+		return PTR_ERR(fields->mode);
+
+	return 0;
+}
+
+static int sama5d3_ebi_init(struct at91_ebi *ebi)
+{
+	struct at91sam9_smc_generic_fields *fields = &ebi->sam9;
+	struct reg_field field = REG_FIELD(0, 0, 31);
+
+	field.id_size = fls(ebi->caps->available_cs);
+	field.id_offset = SAMA5_SMC_GENERIC_BLK_SZ;
+
+	field.reg = AT91SAM9_SMC_SETUP(SAMA5_SMC_GENERIC);
+	fields->setup = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->setup))
+		return PTR_ERR(fields->setup);
+
+	field.reg = AT91SAM9_SMC_PULSE(SAMA5_SMC_GENERIC);
+	fields->pulse = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->pulse))
+		return PTR_ERR(fields->pulse);
+
+	field.reg = AT91SAM9_SMC_CYCLE(SAMA5_SMC_GENERIC);
+	fields->cycle = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->cycle))
+		return PTR_ERR(fields->cycle);
+
+	field.reg = SAMA5_SMC_MODE(SAMA5_SMC_GENERIC);
+	fields->mode = devm_regmap_field_alloc(ebi->dev, ebi->smc, field);
+	if (IS_ERR(fields->mode))
+		return PTR_ERR(fields->mode);
+
+	return 0;
+}
+
+static int at91_ebi_dev_setup(struct at91_ebi *ebi, struct device_node *np,
+			      int reg_cells)
+{
+	const struct at91_ebi_caps *caps = ebi->caps;
+	struct at91_ebi_dev_config conf = { };
+	struct device *dev = ebi->dev;
+	struct at91_ebi_dev *ebid;
+	int ret, numcs = 0, i;
+	bool apply = false;
+
+	numcs = of_property_count_elems_of_size(np, "reg",
+						reg_cells * sizeof(u32));
+	if (numcs <= 0) {
+		dev_err(dev, "invalid reg property in %s\n", np->full_name);
+		return -EINVAL;
+	}
+
+	ebid = devm_kzalloc(ebi->dev,
+			    sizeof(*ebid) + (numcs * sizeof(*ebid->configs)),
+			    GFP_KERNEL);
+	if (!ebid)
+		return -ENOMEM;
+
+	ebid->ebi = ebi;
+
+	ret = caps->xlate_config(ebid, np, &conf);
+	if (ret < 0)
+		return ret;
+	else if (ret)
+		apply = true;
+
+	for (i = 0; i < numcs; i++) {
+		u32 cs;
+
+		ret = of_property_read_u32_index(np, "reg", i * reg_cells,
+						 &cs);
+		if (ret)
+			return ret;
+
+		if (cs > AT91_MATRIX_EBI_NUM_CS ||
+		    !(ebi->caps->available_cs & BIT(cs))) {
+			dev_err(dev, "invalid reg property in %s\n",
+				np->full_name);
+			return -EINVAL;
+		}
+
+		ebid->configs[i].cs = cs;
+
+		if (apply) {
+			conf.cs = cs;
+			ret = caps->apply_config(ebid, &conf);
+			if (ret)
+				return ret;
+		}
+
+		caps->get_config(ebid, &ebid->configs[i]);
+
+		/*
+		 * Attach the EBI device to the generic SMC logic if at least
+		 * one "atmel,smc-" property is present.
+		 */
+		if (ebi->ebi_csa && ret)
+			regmap_field_update_bits(ebi->ebi_csa,
+						 BIT(cs), 0);
+	}
+
+	list_add_tail(&ebid->node, &ebi->devs);
+
+	return 0;
+}
+
+static const struct reg_field at91sam9260_ebi_csa =
+				REG_FIELD(AT91SAM9260_MATRIX_EBICSA, 0,
+					  AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9260_ebi_caps = {
+	.available_cs = 0xff,
+	.ebi_csa = &at91sam9260_ebi_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9261_ebi_csa =
+				REG_FIELD(AT91SAM9261_MATRIX_EBICSA, 0,
+					  AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9261_ebi_caps = {
+	.available_cs = 0xff,
+	.ebi_csa = &at91sam9261_ebi_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9263_ebi0_csa =
+				REG_FIELD(AT91SAM9263_MATRIX_EBI0CSA, 0,
+					  AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9263_ebi0_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9263_ebi0_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9263_ebi1_csa =
+				REG_FIELD(AT91SAM9263_MATRIX_EBI1CSA, 0,
+					  AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9263_ebi1_caps = {
+	.available_cs = 0x7,
+	.ebi_csa = &at91sam9263_ebi1_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9rl_ebi_csa =
+				REG_FIELD(AT91SAM9RL_MATRIX_EBICSA, 0,
+					  AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9rl_ebi_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9rl_ebi_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct reg_field at91sam9g45_ebi_csa =
+				REG_FIELD(AT91SAM9G45_MATRIX_EBICSA, 0,
+					  AT91_MATRIX_EBI_NUM_CS - 1);
+
+static const struct at91_ebi_caps at91sam9g45_ebi_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9g45_ebi_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct at91_ebi_caps at91sam9x5_ebi_caps = {
+	.available_cs = 0x3f,
+	.ebi_csa = &at91sam9263_ebi0_csa,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = at91sam9_ebi_init,
+};
+
+static const struct at91_ebi_caps sama5d3_ebi_caps = {
+	.available_cs = 0xf,
+	.get_config = at91sam9_ebi_get_config,
+	.xlate_config = at91sam9_ebi_xslate_config,
+	.apply_config = at91sam9_ebi_apply_config,
+	.init = sama5d3_ebi_init,
+};
+
+static const struct of_device_id at91_ebi_id_table[] = {
+	{
+		.compatible = "atmel,at91sam9260-ebi",
+		.data = &at91sam9260_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9261-ebi",
+		.data = &at91sam9261_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9263-ebi0",
+		.data = &at91sam9263_ebi0_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9263-ebi1",
+		.data = &at91sam9263_ebi1_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9rl-ebi",
+		.data = &at91sam9rl_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9g45-ebi",
+		.data = &at91sam9g45_ebi_caps,
+	},
+	{
+		.compatible = "atmel,at91sam9x5-ebi",
+		.data = &at91sam9x5_ebi_caps,
+	},
+	{
+		.compatible = "atmel,sama5d3-ebi",
+		.data = &sama5d3_ebi_caps,
+	},
+	{ /* sentinel */ }
+};
+
+static int at91_ebi_dev_disable(struct at91_ebi *ebi, struct device_node *np)
+{
+	struct device *dev = ebi->dev;
+	struct property *newprop;
+
+	newprop = devm_kzalloc(dev, sizeof(*newprop), GFP_KERNEL);
+	if (!newprop)
+		return -ENOMEM;
+
+	newprop->name = devm_kstrdup(dev, "status", GFP_KERNEL);
+	if (!newprop->name)
+		return -ENOMEM;
+
+	newprop->value = devm_kstrdup(dev, "disabled", GFP_KERNEL);
+	if (!newprop->name)
+		return -ENOMEM;
+
+	newprop->length = sizeof("disabled");
+
+	return of_update_property(np, newprop);
+}
+
+static int at91_ebi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *child, *np = dev->of_node;
+	const struct of_device_id *match;
+	struct at91_ebi *ebi;
+	int ret, reg_cells;
+	struct clk *clk;
+	u32 val;
+
+	match = of_match_device(at91_ebi_id_table, dev);
+	if (!match || !match->data)
+		return -EINVAL;
+
+	ebi = devm_kzalloc(dev, sizeof(*ebi), GFP_KERNEL);
+	if (!ebi)
+		return -ENOMEM;
+
+	INIT_LIST_HEAD(&ebi->devs);
+	ebi->caps = match->data;
+	ebi->dev = dev;
+
+	clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(clk))
+		return PTR_ERR(clk);
+
+	ebi->clk = clk;
+
+	ebi->smc = syscon_regmap_lookup_by_phandle(np, "atmel,smc");
+	if (IS_ERR(ebi->smc))
+		return PTR_ERR(ebi->smc);
+
+	/*
+	 * The sama5d3 does not provide an EBICSA register and thus does need
+	 * to access the matrix registers.
+	 */
+	if (ebi->caps->ebi_csa) {
+		ebi->matrix =
+			syscon_regmap_lookup_by_phandle(np, "atmel,matrix");
+		if (IS_ERR(ebi->matrix))
+			return PTR_ERR(ebi->matrix);
+
+		ebi->ebi_csa = regmap_field_alloc(ebi->matrix,
+						  *ebi->caps->ebi_csa);
+		if (IS_ERR(ebi->ebi_csa))
+			return PTR_ERR(ebi->ebi_csa);
+	}
+
+	ret = ebi->caps->init(ebi);
+	if (ret)
+		return ret;
+
+	ret = of_property_read_u32(np, "#address-cells", &val);
+	if (ret) {
+		dev_err(dev, "missing #address-cells property\n");
+		return ret;
+	}
+
+	reg_cells = val;
+
+	ret = of_property_read_u32(np, "#size-cells", &val);
+	if (ret) {
+		dev_err(dev, "missing #address-cells property\n");
+		return ret;
+	}
+
+	reg_cells += val;
+
+	for_each_available_child_of_node(np, child) {
+		if (!of_find_property(child, "reg", NULL))
+			continue;
+
+		ret = at91_ebi_dev_setup(ebi, child, reg_cells);
+		if (ret) {
+			dev_err(dev, "failed to configure EBI bus for %s, disabling the device",
+				child->full_name);
+
+			ret = at91_ebi_dev_disable(ebi, child);
+			if (ret)
+				return ret;
+		}
+	}
+
+	return of_platform_populate(np, NULL, NULL, dev);
+}
+
+static struct platform_driver at91_ebi_driver = {
+	.driver = {
+		.name = "atmel-ebi",
+		.of_match_table	= at91_ebi_id_table,
+	},
+};
+builtin_platform_driver_probe(at91_ebi_driver, at91_ebi_probe);
diff --git a/drivers/memory/atmel-sdramc.c b/drivers/memory/atmel-sdramc.c
index a3ebc8a..53a341f 100644
--- a/drivers/memory/atmel-sdramc.c
+++ b/drivers/memory/atmel-sdramc.c
@@ -1,6 +1,8 @@
 /*
  * Atmel (Multi-port DDR-)SDRAM Controller driver
  *
+ * Author: Alexandre Belloni <alexandre.belloni@free-electrons.com>
+ *
  * Copyright (C) 2014 Atmel
  *
  * This program is free software: you can redistribute it and/or modify
@@ -20,7 +22,7 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 
@@ -48,7 +50,6 @@
 	{ .compatible = "atmel,sama5d3-ddramc", .data = &sama5d3_caps, },
 	{},
 };
-MODULE_DEVICE_TABLE(of, atmel_ramc_of_match);
 
 static int atmel_ramc_probe(struct platform_device *pdev)
 {
@@ -90,8 +91,4 @@
 {
 	return platform_driver_register(&atmel_ramc_driver);
 }
-module_init(atmel_ramc_init);
-
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Alexandre Belloni <alexandre.belloni@free-electrons.com>");
-MODULE_DESCRIPTION("Atmel (Multi-port DDR-)SDRAM Controller");
+device_initcall(atmel_ramc_init);
diff --git a/drivers/memory/omap-gpmc.c b/drivers/memory/omap-gpmc.c
index af4884b..2182988 100644
--- a/drivers/memory/omap-gpmc.c
+++ b/drivers/memory/omap-gpmc.c
@@ -20,7 +20,6 @@
 #include <linux/ioport.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
-#include <linux/module.h>
 #include <linux/gpio/driver.h>
 #include <linux/interrupt.h>
 #include <linux/irqdomain.h>
@@ -1807,7 +1806,6 @@
 	{ .compatible = "ti,am3352-gpmc" },	/* am335x devices */
 	{ }
 };
-MODULE_DEVICE_TABLE(of, gpmc_dt_ids);
 
 /**
  * gpmc_read_settings_dt - read gpmc settings from device-tree
@@ -2155,68 +2153,6 @@
 	return ret;
 }
 
-static int gpmc_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
-{
-	return 1;	/* we're input only */
-}
-
-static int gpmc_gpio_direction_input(struct gpio_chip *chip,
-				     unsigned int offset)
-{
-	return 0;	/* we're input only */
-}
-
-static int gpmc_gpio_direction_output(struct gpio_chip *chip,
-				      unsigned int offset, int value)
-{
-	return -EINVAL;	/* we're input only */
-}
-
-static void gpmc_gpio_set(struct gpio_chip *chip, unsigned int offset,
-			  int value)
-{
-}
-
-static int gpmc_gpio_get(struct gpio_chip *chip, unsigned int offset)
-{
-	u32 reg;
-
-	offset += 8;
-
-	reg = gpmc_read_reg(GPMC_STATUS) & BIT(offset);
-
-	return !!reg;
-}
-
-static int gpmc_gpio_init(struct gpmc_device *gpmc)
-{
-	int ret;
-
-	gpmc->gpio_chip.parent = gpmc->dev;
-	gpmc->gpio_chip.owner = THIS_MODULE;
-	gpmc->gpio_chip.label = DEVICE_NAME;
-	gpmc->gpio_chip.ngpio = gpmc_nr_waitpins;
-	gpmc->gpio_chip.get_direction = gpmc_gpio_get_direction;
-	gpmc->gpio_chip.direction_input = gpmc_gpio_direction_input;
-	gpmc->gpio_chip.direction_output = gpmc_gpio_direction_output;
-	gpmc->gpio_chip.set = gpmc_gpio_set;
-	gpmc->gpio_chip.get = gpmc_gpio_get;
-	gpmc->gpio_chip.base = -1;
-
-	ret = gpiochip_add(&gpmc->gpio_chip);
-	if (ret < 0) {
-		dev_err(gpmc->dev, "could not register gpio chip: %d\n", ret);
-		return ret;
-	}
-
-	return 0;
-}
-
-static void gpmc_gpio_exit(struct gpmc_device *gpmc)
-{
-	gpiochip_remove(&gpmc->gpio_chip);
-}
-
 static int gpmc_probe_dt(struct platform_device *pdev)
 {
 	int ret;
@@ -2281,7 +2217,69 @@
 {
 	return 0;
 }
-#endif
+#endif /* CONFIG_OF */
+
+static int gpmc_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	return 1;	/* we're input only */
+}
+
+static int gpmc_gpio_direction_input(struct gpio_chip *chip,
+				     unsigned int offset)
+{
+	return 0;	/* we're input only */
+}
+
+static int gpmc_gpio_direction_output(struct gpio_chip *chip,
+				      unsigned int offset, int value)
+{
+	return -EINVAL;	/* we're input only */
+}
+
+static void gpmc_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			  int value)
+{
+}
+
+static int gpmc_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	u32 reg;
+
+	offset += 8;
+
+	reg = gpmc_read_reg(GPMC_STATUS) & BIT(offset);
+
+	return !!reg;
+}
+
+static int gpmc_gpio_init(struct gpmc_device *gpmc)
+{
+	int ret;
+
+	gpmc->gpio_chip.parent = gpmc->dev;
+	gpmc->gpio_chip.owner = THIS_MODULE;
+	gpmc->gpio_chip.label = DEVICE_NAME;
+	gpmc->gpio_chip.ngpio = gpmc_nr_waitpins;
+	gpmc->gpio_chip.get_direction = gpmc_gpio_get_direction;
+	gpmc->gpio_chip.direction_input = gpmc_gpio_direction_input;
+	gpmc->gpio_chip.direction_output = gpmc_gpio_direction_output;
+	gpmc->gpio_chip.set = gpmc_gpio_set;
+	gpmc->gpio_chip.get = gpmc_gpio_get;
+	gpmc->gpio_chip.base = -1;
+
+	ret = gpiochip_add(&gpmc->gpio_chip);
+	if (ret < 0) {
+		dev_err(gpmc->dev, "could not register gpio chip: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void gpmc_gpio_exit(struct gpmc_device *gpmc)
+{
+	gpiochip_remove(&gpmc->gpio_chip);
+}
 
 static int gpmc_probe(struct platform_device *pdev)
 {
@@ -2437,15 +2435,7 @@
 {
 	return platform_driver_register(&gpmc_driver);
 }
-
-static __exit void gpmc_exit(void)
-{
-	platform_driver_unregister(&gpmc_driver);
-
-}
-
 postcore_initcall(gpmc_init);
-module_exit(gpmc_exit);
 
 static struct omap3_gpmc_regs gpmc_context;
 
diff --git a/drivers/memory/samsung/exynos-srom.c b/drivers/memory/samsung/exynos-srom.c
index 96756fb..067f533 100644
--- a/drivers/memory/samsung/exynos-srom.c
+++ b/drivers/memory/samsung/exynos-srom.c
@@ -11,7 +11,7 @@
  */
 
 #include <linux/io.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
@@ -91,17 +91,17 @@
 	if (width == 2)
 		cs |= 1 << EXYNOS_SROM_BW__DATAWIDTH__SHIFT;
 
-	bw = __raw_readl(srom->reg_base + EXYNOS_SROM_BW);
+	bw = readl_relaxed(srom->reg_base + EXYNOS_SROM_BW);
 	bw = (bw & ~(EXYNOS_SROM_BW__CS_MASK << bank)) | (cs << bank);
-	__raw_writel(bw, srom->reg_base + EXYNOS_SROM_BW);
+	writel_relaxed(bw, srom->reg_base + EXYNOS_SROM_BW);
 
-	__raw_writel(pmc | (timing[0] << EXYNOS_SROM_BCX__TACP__SHIFT) |
-		    (timing[1] << EXYNOS_SROM_BCX__TCAH__SHIFT) |
-		    (timing[2] << EXYNOS_SROM_BCX__TCOH__SHIFT) |
-		    (timing[3] << EXYNOS_SROM_BCX__TACC__SHIFT) |
-		    (timing[4] << EXYNOS_SROM_BCX__TCOS__SHIFT) |
-		    (timing[5] << EXYNOS_SROM_BCX__TACS__SHIFT),
-		    srom->reg_base + EXYNOS_SROM_BC0 + bank);
+	writel_relaxed(pmc | (timing[0] << EXYNOS_SROM_BCX__TACP__SHIFT) |
+		       (timing[1] << EXYNOS_SROM_BCX__TCAH__SHIFT) |
+		       (timing[2] << EXYNOS_SROM_BCX__TCOH__SHIFT) |
+		       (timing[3] << EXYNOS_SROM_BCX__TACC__SHIFT) |
+		       (timing[4] << EXYNOS_SROM_BCX__TCOS__SHIFT) |
+		       (timing[5] << EXYNOS_SROM_BCX__TACS__SHIFT),
+		       srom->reg_base + EXYNOS_SROM_BC0 + bank);
 
 	return 0;
 }
@@ -159,16 +159,6 @@
 	return of_platform_populate(np, NULL, NULL, dev);
 }
 
-static int exynos_srom_remove(struct platform_device *pdev)
-{
-	struct exynos_srom *srom = platform_get_drvdata(pdev);
-
-	kfree(srom->reg_offset);
-	iounmap(srom->reg_base);
-
-	return 0;
-}
-
 #ifdef CONFIG_PM_SLEEP
 static void exynos_srom_save(void __iomem *base,
 				    struct exynos_srom_reg_dump *rd,
@@ -211,21 +201,16 @@
 	},
 	{},
 };
-MODULE_DEVICE_TABLE(of, of_exynos_srom_ids);
 
 static SIMPLE_DEV_PM_OPS(exynos_srom_pm_ops, exynos_srom_suspend, exynos_srom_resume);
 
 static struct platform_driver exynos_srom_driver = {
 	.probe = exynos_srom_probe,
-	.remove = exynos_srom_remove,
 	.driver = {
 		.name = "exynos-srom",
 		.of_match_table = of_exynos_srom_ids,
 		.pm = &exynos_srom_pm_ops,
+		.suppress_bind_attrs = true,
 	},
 };
-module_platform_driver(exynos_srom_driver);
-
-MODULE_AUTHOR("Pankaj Dubey <pankaj.dubey@samsung.com>");
-MODULE_DESCRIPTION("Exynos SROM Controller Driver");
-MODULE_LICENSE("GPL");
+builtin_platform_driver(exynos_srom_driver);
diff --git a/drivers/memory/tegra/mc.c b/drivers/memory/tegra/mc.c
index a1ae0cc..a4803ac 100644
--- a/drivers/memory/tegra/mc.c
+++ b/drivers/memory/tegra/mc.c
@@ -186,8 +186,10 @@
 		timing = &mc->timings[i++];
 
 		err = load_one_timing(mc, timing, child);
-		if (err)
+		if (err) {
+			of_node_put(child);
 			return err;
+		}
 	}
 
 	return 0;
@@ -206,15 +208,13 @@
 	for_each_child_of_node(mc->dev->of_node, node) {
 		err = of_property_read_u32(node, "nvidia,ram-code",
 					   &node_ram_code);
-		if (err || (node_ram_code != ram_code)) {
-			of_node_put(node);
+		if (err || (node_ram_code != ram_code))
 			continue;
-		}
 
 		err = load_timings(mc, node);
+		of_node_put(node);
 		if (err)
 			return err;
-		of_node_put(node);
 		break;
 	}
 
diff --git a/drivers/memory/tegra/tegra124-emc.c b/drivers/memory/tegra/tegra124-emc.c
index 3dac7be..06cc781 100644
--- a/drivers/memory/tegra/tegra124-emc.c
+++ b/drivers/memory/tegra/tegra124-emc.c
@@ -970,8 +970,10 @@
 		timing = &emc->timings[i++];
 
 		err = load_one_timing_from_dt(emc, timing, child);
-		if (err)
+		if (err) {
+			of_node_put(child);
 			return err;
+		}
 	}
 
 	sort(emc->timings, emc->num_timings, sizeof(*timing), cmp_timings,
@@ -995,10 +997,8 @@
 		u32 value;
 
 		err = of_property_read_u32(np, "nvidia,ram-code", &value);
-		if (err || (value != ram_code)) {
-			of_node_put(np);
+		if (err || (value != ram_code))
 			continue;
-		}
 
 		return np;
 	}
diff --git a/drivers/of/of_reserved_mem.c b/drivers/of/of_reserved_mem.c
index ed01c01..04e4fe5 100644
--- a/drivers/of/of_reserved_mem.c
+++ b/drivers/of/of_reserved_mem.c
@@ -21,6 +21,7 @@
 #include <linux/sizes.h>
 #include <linux/of_reserved_mem.h>
 #include <linux/sort.h>
+#include <linux/slab.h>
 
 #define MAX_RESERVED_REGIONS	16
 static struct reserved_mem reserved_mem[MAX_RESERVED_REGIONS];
@@ -289,53 +290,95 @@
 	return NULL;
 }
 
-/**
- * of_reserved_mem_device_init() - assign reserved memory region to given device
- *
- * This function assign memory region pointed by "memory-region" device tree
- * property to the given device.
- */
-int of_reserved_mem_device_init(struct device *dev)
-{
+struct rmem_assigned_device {
+	struct device *dev;
 	struct reserved_mem *rmem;
-	struct device_node *np;
+	struct list_head list;
+};
+
+static LIST_HEAD(of_rmem_assigned_device_list);
+static DEFINE_MUTEX(of_rmem_assigned_device_mutex);
+
+/**
+ * of_reserved_mem_device_init_by_idx() - assign reserved memory region to
+ *					  given device
+ * @dev:	Pointer to the device to configure
+ * @np:		Pointer to the device_node with 'reserved-memory' property
+ * @idx:	Index of selected region
+ *
+ * This function assigns respective DMA-mapping operations based on reserved
+ * memory region specified by 'memory-region' property in @np node to the @dev
+ * device. When driver needs to use more than one reserved memory region, it
+ * should allocate child devices and initialize regions by name for each of
+ * child device.
+ *
+ * Returns error code or zero on success.
+ */
+int of_reserved_mem_device_init_by_idx(struct device *dev,
+				       struct device_node *np, int idx)
+{
+	struct rmem_assigned_device *rd;
+	struct device_node *target;
+	struct reserved_mem *rmem;
 	int ret;
 
-	np = of_parse_phandle(dev->of_node, "memory-region", 0);
-	if (!np)
-		return -ENODEV;
+	if (!np || !dev)
+		return -EINVAL;
 
-	rmem = __find_rmem(np);
-	of_node_put(np);
+	target = of_parse_phandle(np, "memory-region", idx);
+	if (!target)
+		return -EINVAL;
+
+	rmem = __find_rmem(target);
+	of_node_put(target);
 
 	if (!rmem || !rmem->ops || !rmem->ops->device_init)
 		return -EINVAL;
 
+	rd = kmalloc(sizeof(struct rmem_assigned_device), GFP_KERNEL);
+	if (!rd)
+		return -ENOMEM;
+
 	ret = rmem->ops->device_init(rmem, dev);
-	if (ret == 0)
+	if (ret == 0) {
+		rd->dev = dev;
+		rd->rmem = rmem;
+
+		mutex_lock(&of_rmem_assigned_device_mutex);
+		list_add(&rd->list, &of_rmem_assigned_device_list);
+		mutex_unlock(&of_rmem_assigned_device_mutex);
+
 		dev_info(dev, "assigned reserved memory node %s\n", rmem->name);
+	} else {
+		kfree(rd);
+	}
 
 	return ret;
 }
-EXPORT_SYMBOL_GPL(of_reserved_mem_device_init);
+EXPORT_SYMBOL_GPL(of_reserved_mem_device_init_by_idx);
 
 /**
  * of_reserved_mem_device_release() - release reserved memory device structures
+ * @dev:	Pointer to the device to deconfigure
  *
  * This function releases structures allocated for memory region handling for
  * the given device.
  */
 void of_reserved_mem_device_release(struct device *dev)
 {
-	struct reserved_mem *rmem;
-	struct device_node *np;
+	struct rmem_assigned_device *rd;
+	struct reserved_mem *rmem = NULL;
 
-	np = of_parse_phandle(dev->of_node, "memory-region", 0);
-	if (!np)
-		return;
-
-	rmem = __find_rmem(np);
-	of_node_put(np);
+	mutex_lock(&of_rmem_assigned_device_mutex);
+	list_for_each_entry(rd, &of_rmem_assigned_device_list, list) {
+		if (rd->dev == dev) {
+			rmem = rd->rmem;
+			list_del(&rd->list);
+			kfree(rd);
+			break;
+		}
+	}
+	mutex_unlock(&of_rmem_assigned_device_mutex);
 
 	if (!rmem || !rmem->ops || !rmem->ops->device_release)
 		return;
diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig
index 9bb2622..f38ac90 100644
--- a/drivers/power/reset/Kconfig
+++ b/drivers/power/reset/Kconfig
@@ -46,6 +46,16 @@
 
 	  Say Y if you have an Axxia family SoC.
 
+config POWER_RESET_BRCMKONA
+	bool "Broadcom Kona reset driver"
+	depends on ARM || COMPILE_TEST
+	default ARCH_BCM_MOBILE
+	help
+	  This driver provides restart support for Broadcom Kona chips.
+
+	  Say Y here if you have a Broadcom Kona-based board and you wish
+	  to have restart support.
+
 config POWER_RESET_BRCMSTB
 	bool "Broadcom STB reset driver"
 	depends on ARM || MIPS || COMPILE_TEST
diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile
index ab7aa86..6b6eeb3 100644
--- a/drivers/power/reset/Makefile
+++ b/drivers/power/reset/Makefile
@@ -3,6 +3,7 @@
 obj-$(CONFIG_POWER_RESET_AT91_RESET) += at91-reset.o
 obj-$(CONFIG_POWER_RESET_AT91_SAMA5D2_SHDWC) += at91-sama5d2_shdwc.o
 obj-$(CONFIG_POWER_RESET_AXXIA) += axxia-reset.o
+obj-$(CONFIG_POWER_RESET_BRCMKONA) += brcm-kona-reset.o
 obj-$(CONFIG_POWER_RESET_BRCMSTB) += brcmstb-reboot.o
 obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o
 obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o
diff --git a/drivers/power/reset/brcm-kona-reset.c b/drivers/power/reset/brcm-kona-reset.c
new file mode 100644
index 0000000..8eaa959
--- /dev/null
+++ b/drivers/power/reset/brcm-kona-reset.c
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/reboot.h>
+
+#define RSTMGR_REG_WR_ACCESS_OFFSET	0
+#define RSTMGR_REG_CHIP_SOFT_RST_OFFSET	4
+
+#define RSTMGR_WR_PASSWORD		0xa5a5
+#define RSTMGR_WR_PASSWORD_SHIFT	8
+#define RSTMGR_WR_ACCESS_ENABLE		1
+
+static void __iomem *kona_reset_base;
+
+static int kona_reset_handler(struct notifier_block *this,
+				unsigned long mode, void *cmd)
+{
+	/*
+	 * A soft reset is triggered by writing a 0 to bit 0 of the soft reset
+	 * register. To write to that register we must first write the password
+	 * and the enable bit in the write access enable register.
+	 */
+	writel((RSTMGR_WR_PASSWORD << RSTMGR_WR_PASSWORD_SHIFT) |
+		RSTMGR_WR_ACCESS_ENABLE,
+		kona_reset_base + RSTMGR_REG_WR_ACCESS_OFFSET);
+	writel(0, kona_reset_base + RSTMGR_REG_CHIP_SOFT_RST_OFFSET);
+
+	return NOTIFY_DONE;
+}
+
+static struct notifier_block kona_reset_nb = {
+	.notifier_call = kona_reset_handler,
+	.priority = 128,
+};
+
+static int kona_reset_probe(struct platform_device *pdev)
+{
+	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	kona_reset_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(kona_reset_base))
+		return PTR_ERR(kona_reset_base);
+
+	return register_restart_handler(&kona_reset_nb);
+}
+
+static const struct of_device_id of_match[] = {
+	{ .compatible = "brcm,bcm21664-resetmgr" },
+	{},
+};
+
+static struct platform_driver bcm_kona_reset_driver = {
+	.probe = kona_reset_probe,
+	.driver = {
+		.name = "brcm-kona-reset",
+		.of_match_table = of_match,
+	},
+};
+
+builtin_platform_driver(bcm_kona_reset_driver);
diff --git a/drivers/pwm/pwm-clps711x.c b/drivers/pwm/pwm-clps711x.c
index 7d33542..26ec24e 100644
--- a/drivers/pwm/pwm-clps711x.c
+++ b/drivers/pwm/pwm-clps711x.c
@@ -155,7 +155,7 @@
 }
 
 static const struct of_device_id __maybe_unused clps711x_pwm_dt_ids[] = {
-	{ .compatible = "cirrus,clps711x-pwm", },
+	{ .compatible = "cirrus,ep7209-pwm", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, clps711x_pwm_dt_ids);
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 0b2733d..4be1b8c 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -12,8 +12,22 @@
 
 	  If unsure, say no.
 
+if RESET_CONTROLLER
+
 config RESET_OXNAS
 	bool
 
+config TI_SYSCON_RESET
+	tristate "TI SYSCON Reset Driver"
+	depends on HAS_IOMEM
+	select MFD_SYSCON
+	help
+	  This enables the reset driver support for TI devices with
+	  memory-mapped reset registers as part of a syscon device node. If
+	  you wish to use the reset framework for such memory-mapped devices,
+	  say Y here. Otherwise, say N.
+
 source "drivers/reset/sti/Kconfig"
 source "drivers/reset/hisilicon/Kconfig"
+
+endif
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index f173fc3..5d65a93 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -3,9 +3,11 @@
 obj-$(CONFIG_ARCH_SOCFPGA) += reset-socfpga.o
 obj-$(CONFIG_ARCH_BERLIN) += reset-berlin.o
 obj-$(CONFIG_MACH_PISTACHIO) += reset-pistachio.o
+obj-$(CONFIG_ARCH_MESON) += reset-meson.o
 obj-$(CONFIG_ARCH_SUNXI) += reset-sunxi.o
 obj-$(CONFIG_ARCH_STI) += sti/
 obj-$(CONFIG_ARCH_HISI) += hisilicon/
 obj-$(CONFIG_ARCH_ZYNQ) += reset-zynq.o
 obj-$(CONFIG_ATH79) += reset-ath79.o
 obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o
+obj-$(CONFIG_TI_SYSCON_RESET) += reset-ti-syscon.o
diff --git a/drivers/reset/core.c b/drivers/reset/core.c
index 72b32bd..395dc9c 100644
--- a/drivers/reset/core.c
+++ b/drivers/reset/core.c
@@ -93,6 +93,43 @@
 }
 EXPORT_SYMBOL_GPL(reset_controller_unregister);
 
+static void devm_reset_controller_release(struct device *dev, void *res)
+{
+	reset_controller_unregister(*(struct reset_controller_dev **)res);
+}
+
+/**
+ * devm_reset_controller_register - resource managed reset_controller_register()
+ * @dev: device that is registering this reset controller
+ * @rcdev: a pointer to the initialized reset controller device
+ *
+ * Managed reset_controller_register(). For reset controllers registered by
+ * this function, reset_controller_unregister() is automatically called on
+ * driver detach. See reset_controller_register() for more information.
+ */
+int devm_reset_controller_register(struct device *dev,
+				   struct reset_controller_dev *rcdev)
+{
+	struct reset_controller_dev **rcdevp;
+	int ret;
+
+	rcdevp = devres_alloc(devm_reset_controller_release, sizeof(*rcdevp),
+			      GFP_KERNEL);
+	if (!rcdevp)
+		return -ENOMEM;
+
+	ret = reset_controller_register(rcdev);
+	if (!ret) {
+		*rcdevp = rcdev;
+		devres_add(dev, rcdevp);
+	} else {
+		devres_free(rcdevp);
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(devm_reset_controller_register);
+
 /**
  * reset_control_reset - reset the controlled device
  * @rstc: reset controller
diff --git a/drivers/reset/hisilicon/hi6220_reset.c b/drivers/reset/hisilicon/hi6220_reset.c
index 8f55fd4..35ce53e 100644
--- a/drivers/reset/hisilicon/hi6220_reset.c
+++ b/drivers/reset/hisilicon/hi6220_reset.c
@@ -1,7 +1,8 @@
 /*
  * Hisilicon Hi6220 reset controller driver
  *
- * Copyright (c) 2015 Hisilicon Limited.
+ * Copyright (c) 2016 Linaro Limited.
+ * Copyright (c) 2015-2016 Hisilicon Limited.
  *
  * Author: Feng Chen <puck.chen@hisilicon.com>
  *
@@ -15,81 +16,130 @@
 #include <linux/module.h>
 #include <linux/bitops.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
 #include <linux/reset-controller.h>
 #include <linux/reset.h>
 #include <linux/platform_device.h>
 
-#define ASSERT_OFFSET            0x300
-#define DEASSERT_OFFSET          0x304
-#define MAX_INDEX                0x509
+#define PERIPH_ASSERT_OFFSET      0x300
+#define PERIPH_DEASSERT_OFFSET    0x304
+#define PERIPH_MAX_INDEX          0x509
+
+#define SC_MEDIA_RSTEN            0x052C
+#define SC_MEDIA_RSTDIS           0x0530
+#define MEDIA_MAX_INDEX           8
 
 #define to_reset_data(x) container_of(x, struct hi6220_reset_data, rc_dev)
 
-struct hi6220_reset_data {
-	void __iomem			*assert_base;
-	void __iomem			*deassert_base;
-	struct reset_controller_dev	rc_dev;
+enum hi6220_reset_ctrl_type {
+	PERIPHERAL,
+	MEDIA,
 };
 
-static int hi6220_reset_assert(struct reset_controller_dev *rc_dev,
+struct hi6220_reset_data {
+	struct reset_controller_dev rc_dev;
+	struct regmap *regmap;
+};
+
+static int hi6220_peripheral_assert(struct reset_controller_dev *rc_dev,
+				    unsigned long idx)
+{
+	struct hi6220_reset_data *data = to_reset_data(rc_dev);
+	struct regmap *regmap = data->regmap;
+	u32 bank = idx >> 8;
+	u32 offset = idx & 0xff;
+	u32 reg = PERIPH_ASSERT_OFFSET + bank * 0x10;
+
+	return regmap_write(regmap, reg, BIT(offset));
+}
+
+static int hi6220_peripheral_deassert(struct reset_controller_dev *rc_dev,
+				      unsigned long idx)
+{
+	struct hi6220_reset_data *data = to_reset_data(rc_dev);
+	struct regmap *regmap = data->regmap;
+	u32 bank = idx >> 8;
+	u32 offset = idx & 0xff;
+	u32 reg = PERIPH_DEASSERT_OFFSET + bank * 0x10;
+
+	return regmap_write(regmap, reg, BIT(offset));
+}
+
+static const struct reset_control_ops hi6220_peripheral_reset_ops = {
+	.assert = hi6220_peripheral_assert,
+	.deassert = hi6220_peripheral_deassert,
+};
+
+static int hi6220_media_assert(struct reset_controller_dev *rc_dev,
 			       unsigned long idx)
 {
 	struct hi6220_reset_data *data = to_reset_data(rc_dev);
+	struct regmap *regmap = data->regmap;
 
-	int bank = idx >> 8;
-	int offset = idx & 0xff;
-
-	writel(BIT(offset), data->assert_base + (bank * 0x10));
-
-	return 0;
+	return regmap_write(regmap, SC_MEDIA_RSTEN, BIT(idx));
 }
 
-static int hi6220_reset_deassert(struct reset_controller_dev *rc_dev,
+static int hi6220_media_deassert(struct reset_controller_dev *rc_dev,
 				 unsigned long idx)
 {
 	struct hi6220_reset_data *data = to_reset_data(rc_dev);
+	struct regmap *regmap = data->regmap;
 
-	int bank = idx >> 8;
-	int offset = idx & 0xff;
-
-	writel(BIT(offset), data->deassert_base + (bank * 0x10));
-
-	return 0;
+	return regmap_write(regmap, SC_MEDIA_RSTDIS, BIT(idx));
 }
 
-static const struct reset_control_ops hi6220_reset_ops = {
-	.assert = hi6220_reset_assert,
-	.deassert = hi6220_reset_deassert,
+static const struct reset_control_ops hi6220_media_reset_ops = {
+	.assert = hi6220_media_assert,
+	.deassert = hi6220_media_deassert,
 };
 
 static int hi6220_reset_probe(struct platform_device *pdev)
 {
+	struct device_node *np = pdev->dev.of_node;
+	struct device *dev = &pdev->dev;
+	enum hi6220_reset_ctrl_type type;
 	struct hi6220_reset_data *data;
-	struct resource *res;
-	void __iomem *src_base;
+	struct regmap *regmap;
 
-	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	src_base = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(src_base))
-		return PTR_ERR(src_base);
+	type = (enum hi6220_reset_ctrl_type)of_device_get_match_data(dev);
 
-	data->assert_base = src_base + ASSERT_OFFSET;
-	data->deassert_base = src_base + DEASSERT_OFFSET;
-	data->rc_dev.nr_resets = MAX_INDEX;
-	data->rc_dev.ops = &hi6220_reset_ops;
-	data->rc_dev.of_node = pdev->dev.of_node;
+	regmap = syscon_node_to_regmap(np);
+	if (IS_ERR(regmap)) {
+		dev_err(dev, "failed to get reset controller regmap\n");
+		return PTR_ERR(regmap);
+	}
+
+	data->regmap = regmap;
+	data->rc_dev.of_node = np;
+	if (type == MEDIA) {
+		data->rc_dev.ops = &hi6220_media_reset_ops;
+		data->rc_dev.nr_resets = MEDIA_MAX_INDEX;
+	} else {
+		data->rc_dev.ops = &hi6220_peripheral_reset_ops;
+		data->rc_dev.nr_resets = PERIPH_MAX_INDEX;
+	}
 
 	return reset_controller_register(&data->rc_dev);
 }
 
 static const struct of_device_id hi6220_reset_match[] = {
-	{ .compatible = "hisilicon,hi6220-sysctrl" },
-	{ },
+	{
+		.compatible = "hisilicon,hi6220-sysctrl",
+		.data = (void *)PERIPHERAL,
+	},
+	{
+		.compatible = "hisilicon,hi6220-mediactrl",
+		.data = (void *)MEDIA,
+	},
+	{ /* sentinel */ },
 };
+MODULE_DEVICE_TABLE(of, hi6220_reset_match);
 
 static struct platform_driver hi6220_reset_driver = {
 	.probe = hi6220_reset_probe,
diff --git a/drivers/reset/reset-ath79.c b/drivers/reset/reset-ath79.c
index ccb940a..16d410c 100644
--- a/drivers/reset/reset-ath79.c
+++ b/drivers/reset/reset-ath79.c
@@ -112,7 +112,7 @@
 	ath79_reset->rcdev.of_reset_n_cells = 1;
 	ath79_reset->rcdev.nr_resets = 32;
 
-	err = reset_controller_register(&ath79_reset->rcdev);
+	err = devm_reset_controller_register(&pdev->dev, &ath79_reset->rcdev);
 	if (err)
 		return err;
 
@@ -131,7 +131,6 @@
 	struct ath79_reset *ath79_reset = platform_get_drvdata(pdev);
 
 	unregister_restart_handler(&ath79_reset->restart_nb);
-	reset_controller_unregister(&ath79_reset->rcdev);
 
 	return 0;
 }
diff --git a/drivers/reset/reset-meson.c b/drivers/reset/reset-meson.c
new file mode 100644
index 0000000..c32f11a
--- /dev/null
+++ b/drivers/reset/reset-meson.c
@@ -0,0 +1,136 @@
+/*
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ * The full GNU General Public License is included in this distribution
+ * in the file called COPYING.
+ *
+ * BSD LICENSE
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *   * Redistributions of source code must retain the above copyright
+ *     notice, this list of conditions and the following disclaimer.
+ *   * Redistributions in binary form must reproduce the above copyright
+ *     notice, this list of conditions and the following disclaimer in
+ *     the documentation and/or other materials provided with the
+ *     distribution.
+ *   * Neither the name of Intel Corporation nor the names of its
+ *     contributors may be used to endorse or promote products derived
+ *     from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define REG_COUNT	8
+#define BITS_PER_REG	32
+
+struct meson_reset {
+	void __iomem *reg_base;
+	struct reset_controller_dev rcdev;
+};
+
+static int meson_reset_reset(struct reset_controller_dev *rcdev,
+			      unsigned long id)
+{
+	struct meson_reset *data =
+		container_of(rcdev, struct meson_reset, rcdev);
+	unsigned int bank = id / BITS_PER_REG;
+	unsigned int offset = id % BITS_PER_REG;
+	void __iomem *reg_addr = data->reg_base + (bank << 2);
+
+	if (bank >= REG_COUNT)
+		return -EINVAL;
+
+	writel(BIT(offset), reg_addr);
+
+	return 0;
+}
+
+static const struct reset_control_ops meson_reset_ops = {
+	.reset		= meson_reset_reset,
+};
+
+static const struct of_device_id meson_reset_dt_ids[] = {
+	 { .compatible = "amlogic,meson8b-reset", },
+	 { .compatible = "amlogic,meson-gxbb-reset", },
+	 { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, meson_reset_dt_ids);
+
+static int meson_reset_probe(struct platform_device *pdev)
+{
+	struct meson_reset *data;
+	struct resource *res;
+
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	data->reg_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(data->reg_base))
+		return PTR_ERR(data->reg_base);
+
+	platform_set_drvdata(pdev, data);
+
+	data->rcdev.owner = THIS_MODULE;
+	data->rcdev.nr_resets = REG_COUNT * BITS_PER_REG;
+	data->rcdev.ops = &meson_reset_ops;
+	data->rcdev.of_node = pdev->dev.of_node;
+
+	return devm_reset_controller_register(&pdev->dev, &data->rcdev);
+}
+
+static struct platform_driver meson_reset_driver = {
+	.probe	= meson_reset_probe,
+	.driver = {
+		.name		= "meson_reset",
+		.of_match_table	= meson_reset_dt_ids,
+	},
+};
+
+module_platform_driver(meson_reset_driver);
+
+MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
+MODULE_DESCRIPTION("Amlogic Meson Reset Controller driver");
+MODULE_LICENSE("Dual BSD/GPL");
diff --git a/drivers/reset/reset-oxnas.c b/drivers/reset/reset-oxnas.c
index c60fb2d..9449805 100644
--- a/drivers/reset/reset-oxnas.c
+++ b/drivers/reset/reset-oxnas.c
@@ -112,21 +112,11 @@
 	data->rcdev.ops = &oxnas_reset_ops;
 	data->rcdev.of_node = pdev->dev.of_node;
 
-	return reset_controller_register(&data->rcdev);
-}
-
-static int oxnas_reset_remove(struct platform_device *pdev)
-{
-	struct oxnas_reset *data = platform_get_drvdata(pdev);
-
-	reset_controller_unregister(&data->rcdev);
-
-	return 0;
+	return devm_reset_controller_register(&pdev->dev, &data->rcdev);
 }
 
 static struct platform_driver oxnas_reset_driver = {
 	.probe	= oxnas_reset_probe,
-	.remove	= oxnas_reset_remove,
 	.driver = {
 		.name		= "oxnas-reset",
 		.of_match_table	= oxnas_reset_dt_ids,
diff --git a/drivers/reset/reset-pistachio.c b/drivers/reset/reset-pistachio.c
index 72a97a1..bbc4c06 100644
--- a/drivers/reset/reset-pistachio.c
+++ b/drivers/reset/reset-pistachio.c
@@ -121,16 +121,7 @@
 	rd->rcdev.ops = &pistachio_reset_ops;
 	rd->rcdev.of_node = np;
 
-	return reset_controller_register(&rd->rcdev);
-}
-
-static int pistachio_reset_remove(struct platform_device *pdev)
-{
-	struct pistachio_reset_data *data = platform_get_drvdata(pdev);
-
-	reset_controller_unregister(&data->rcdev);
-
-	return 0;
+	return devm_reset_controller_register(dev, &rd->rcdev);
 }
 
 static const struct of_device_id pistachio_reset_dt_ids[] = {
@@ -141,7 +132,6 @@
 
 static struct platform_driver pistachio_reset_driver = {
 	.probe	= pistachio_reset_probe,
-	.remove	= pistachio_reset_remove,
 	.driver = {
 		.name		= "pistachio-reset",
 		.of_match_table	= pistachio_reset_dt_ids,
diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
index cd05a70..12add9b 100644
--- a/drivers/reset/reset-socfpga.c
+++ b/drivers/reset/reset-socfpga.c
@@ -134,16 +134,7 @@
 	data->rcdev.ops = &socfpga_reset_ops;
 	data->rcdev.of_node = pdev->dev.of_node;
 
-	return reset_controller_register(&data->rcdev);
-}
-
-static int socfpga_reset_remove(struct platform_device *pdev)
-{
-	struct socfpga_reset_data *data = platform_get_drvdata(pdev);
-
-	reset_controller_unregister(&data->rcdev);
-
-	return 0;
+	return devm_reset_controller_register(dev, &data->rcdev);
 }
 
 static const struct of_device_id socfpga_reset_dt_ids[] = {
@@ -153,7 +144,6 @@
 
 static struct platform_driver socfpga_reset_driver = {
 	.probe	= socfpga_reset_probe,
-	.remove	= socfpga_reset_remove,
 	.driver = {
 		.name		= "socfpga-reset",
 		.of_match_table	= socfpga_reset_dt_ids,
diff --git a/drivers/reset/reset-sunxi.c b/drivers/reset/reset-sunxi.c
index 677f865..3080190 100644
--- a/drivers/reset/reset-sunxi.c
+++ b/drivers/reset/reset-sunxi.c
@@ -165,21 +165,11 @@
 	data->rcdev.ops = &sunxi_reset_ops;
 	data->rcdev.of_node = pdev->dev.of_node;
 
-	return reset_controller_register(&data->rcdev);
-}
-
-static int sunxi_reset_remove(struct platform_device *pdev)
-{
-	struct sunxi_reset_data *data = platform_get_drvdata(pdev);
-
-	reset_controller_unregister(&data->rcdev);
-
-	return 0;
+	return devm_reset_controller_register(&pdev->dev, &data->rcdev);
 }
 
 static struct platform_driver sunxi_reset_driver = {
 	.probe	= sunxi_reset_probe,
-	.remove	= sunxi_reset_remove,
 	.driver = {
 		.name		= "sunxi-reset",
 		.of_match_table	= sunxi_reset_dt_ids,
diff --git a/drivers/reset/reset-ti-syscon.c b/drivers/reset/reset-ti-syscon.c
new file mode 100644
index 0000000..47f0ffd
--- /dev/null
+++ b/drivers/reset/reset-ti-syscon.c
@@ -0,0 +1,237 @@
+/*
+ * TI SYSCON regmap reset driver
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *	Andrew F. Davis <afd@ti.com>
+ *	Suman Anna <afd@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset-controller.h>
+
+#include <dt-bindings/reset/ti-syscon.h>
+
+/**
+ * struct ti_syscon_reset_control - reset control structure
+ * @assert_offset: reset assert control register offset from syscon base
+ * @assert_bit: reset assert bit in the reset assert control register
+ * @deassert_offset: reset deassert control register offset from syscon base
+ * @deassert_bit: reset deassert bit in the reset deassert control register
+ * @status_offset: reset status register offset from syscon base
+ * @status_bit: reset status bit in the reset status register
+ * @flags: reset flag indicating how the (de)assert and status are handled
+ */
+struct ti_syscon_reset_control {
+	unsigned int assert_offset;
+	unsigned int assert_bit;
+	unsigned int deassert_offset;
+	unsigned int deassert_bit;
+	unsigned int status_offset;
+	unsigned int status_bit;
+	u32 flags;
+};
+
+/**
+ * struct ti_syscon_reset_data - reset controller information structure
+ * @rcdev: reset controller entity
+ * @regmap: regmap handle containing the memory-mapped reset registers
+ * @controls: array of reset controls
+ * @nr_controls: number of controls in control array
+ */
+struct ti_syscon_reset_data {
+	struct reset_controller_dev rcdev;
+	struct regmap *regmap;
+	struct ti_syscon_reset_control *controls;
+	unsigned int nr_controls;
+};
+
+#define to_ti_syscon_reset_data(rcdev)	\
+	container_of(rcdev, struct ti_syscon_reset_data, rcdev)
+
+/**
+ * ti_syscon_reset_assert() - assert device reset
+ * @rcdev: reset controller entity
+ * @id: ID of the reset to be asserted
+ *
+ * This function implements the reset driver op to assert a device's reset.
+ * This asserts the reset in a manner prescribed by the reset flags.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int ti_syscon_reset_assert(struct reset_controller_dev *rcdev,
+				  unsigned long id)
+{
+	struct ti_syscon_reset_data *data = to_ti_syscon_reset_data(rcdev);
+	struct ti_syscon_reset_control *control;
+	unsigned int mask, value;
+
+	if (id >= data->nr_controls)
+		return -EINVAL;
+
+	control = &data->controls[id];
+
+	if (control->flags & ASSERT_NONE)
+		return -ENOTSUPP; /* assert not supported for this reset */
+
+	mask = BIT(control->assert_bit);
+	value = (control->flags & ASSERT_SET) ? mask : 0x0;
+
+	return regmap_update_bits(data->regmap, control->assert_offset, mask, value);
+}
+
+/**
+ * ti_syscon_reset_deassert() - deassert device reset
+ * @rcdev: reset controller entity
+ * @id: ID of reset to be deasserted
+ *
+ * This function implements the reset driver op to deassert a device's reset.
+ * This deasserts the reset in a manner prescribed by the reset flags.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int ti_syscon_reset_deassert(struct reset_controller_dev *rcdev,
+				    unsigned long id)
+{
+	struct ti_syscon_reset_data *data = to_ti_syscon_reset_data(rcdev);
+	struct ti_syscon_reset_control *control;
+	unsigned int mask, value;
+
+	if (id >= data->nr_controls)
+		return -EINVAL;
+
+	control = &data->controls[id];
+
+	if (control->flags & DEASSERT_NONE)
+		return -ENOTSUPP; /* deassert not supported for this reset */
+
+	mask = BIT(control->deassert_bit);
+	value = (control->flags & DEASSERT_SET) ? mask : 0x0;
+
+	return regmap_update_bits(data->regmap, control->deassert_offset, mask, value);
+}
+
+/**
+ * ti_syscon_reset_status() - check device reset status
+ * @rcdev: reset controller entity
+ * @id: ID of the reset for which the status is being requested
+ *
+ * This function implements the reset driver op to return the status of a
+ * device's reset.
+ *
+ * Return: 0 if reset is deasserted, true if reset is asserted, else a
+ * corresponding error value
+ */
+static int ti_syscon_reset_status(struct reset_controller_dev *rcdev,
+				  unsigned long id)
+{
+	struct ti_syscon_reset_data *data = to_ti_syscon_reset_data(rcdev);
+	struct ti_syscon_reset_control *control;
+	unsigned int reset_state;
+	int ret;
+
+	if (id >= data->nr_controls)
+		return -EINVAL;
+
+	control = &data->controls[id];
+
+	if (control->flags & STATUS_NONE)
+		return -ENOTSUPP; /* status not supported for this reset */
+
+	ret = regmap_read(data->regmap, control->status_offset, &reset_state);
+	if (ret)
+		return ret;
+
+	return (reset_state & BIT(control->status_bit)) &&
+			(control->flags & STATUS_SET);
+}
+
+static struct reset_control_ops ti_syscon_reset_ops = {
+	.assert		= ti_syscon_reset_assert,
+	.deassert	= ti_syscon_reset_deassert,
+	.status		= ti_syscon_reset_status,
+};
+
+static int ti_syscon_reset_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct ti_syscon_reset_data *data;
+	struct regmap *regmap;
+	const __be32 *list;
+	struct ti_syscon_reset_control *controls;
+	int size, nr_controls, i;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	regmap = syscon_node_to_regmap(np->parent);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	list = of_get_property(np, "ti,reset-bits", &size);
+	if (!list || (size / sizeof(*list)) % 7 != 0) {
+		dev_err(dev, "invalid DT reset description\n");
+		return -EINVAL;
+	}
+
+	nr_controls = (size / sizeof(*list)) / 7;
+	controls = devm_kzalloc(dev, nr_controls * sizeof(*controls), GFP_KERNEL);
+	if (!controls)
+		return -ENOMEM;
+
+	for (i = 0; i < nr_controls; i++) {
+		controls[i].assert_offset = be32_to_cpup(list++);
+		controls[i].assert_bit = be32_to_cpup(list++);
+		controls[i].deassert_offset = be32_to_cpup(list++);
+		controls[i].deassert_bit = be32_to_cpup(list++);
+		controls[i].status_offset = be32_to_cpup(list++);
+		controls[i].status_bit = be32_to_cpup(list++);
+		controls[i].flags = be32_to_cpup(list++);
+	}
+
+	data->rcdev.ops = &ti_syscon_reset_ops;
+	data->rcdev.owner = THIS_MODULE;
+	data->rcdev.of_node = np;
+	data->rcdev.nr_resets = nr_controls;
+	data->regmap = regmap;
+	data->controls = controls;
+	data->nr_controls = nr_controls;
+
+	platform_set_drvdata(pdev, data);
+
+	return devm_reset_controller_register(dev, &data->rcdev);
+}
+
+static const struct of_device_id ti_syscon_reset_of_match[] = {
+	{ .compatible = "ti,syscon-reset", },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ti_syscon_reset_of_match);
+
+static struct platform_driver ti_syscon_reset_driver = {
+	.probe = ti_syscon_reset_probe,
+	.driver = {
+		.name = "ti-syscon-reset",
+		.of_match_table = ti_syscon_reset_of_match,
+	},
+};
+module_platform_driver(ti_syscon_reset_driver);
+
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_AUTHOR("Suman Anna <s-anna@ti.com>");
+MODULE_DESCRIPTION("TI SYSCON Regmap Reset Driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/reset/reset-zynq.c b/drivers/reset/reset-zynq.c
index a7e87bc..138f2f2 100644
--- a/drivers/reset/reset-zynq.c
+++ b/drivers/reset/reset-zynq.c
@@ -122,16 +122,7 @@
 	priv->rcdev.ops = &zynq_reset_ops;
 	priv->rcdev.of_node = pdev->dev.of_node;
 
-	return reset_controller_register(&priv->rcdev);
-}
-
-static int zynq_reset_remove(struct platform_device *pdev)
-{
-	struct zynq_reset_data *priv = platform_get_drvdata(pdev);
-
-	reset_controller_unregister(&priv->rcdev);
-
-	return 0;
+	return devm_reset_controller_register(&pdev->dev, &priv->rcdev);
 }
 
 static const struct of_device_id zynq_reset_dt_ids[] = {
@@ -141,7 +132,6 @@
 
 static struct platform_driver zynq_reset_driver = {
 	.probe	= zynq_reset_probe,
-	.remove	= zynq_reset_remove,
 	.driver = {
 		.name		= KBUILD_MODNAME,
 		.of_match_table	= zynq_reset_dt_ids,
diff --git a/drivers/reset/sti/Kconfig b/drivers/reset/sti/Kconfig
index f8c15a3..6131785 100644
--- a/drivers/reset/sti/Kconfig
+++ b/drivers/reset/sti/Kconfig
@@ -2,7 +2,6 @@
 
 config STI_RESET_SYSCFG
 	bool
-	select RESET_CONTROLLER
 
 config STIH415_RESET
 	bool
diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig
index cb58ef0..91d5c05 100644
--- a/drivers/soc/Kconfig
+++ b/drivers/soc/Kconfig
@@ -1,7 +1,6 @@
 menu "SOC (System On Chip) specific Drivers"
 
 source "drivers/soc/bcm/Kconfig"
-source "drivers/soc/brcmstb/Kconfig"
 source "drivers/soc/fsl/qe/Kconfig"
 source "drivers/soc/mediatek/Kconfig"
 source "drivers/soc/qcom/Kconfig"
diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile
index 380230f..b75e3bd 100644
--- a/drivers/soc/Makefile
+++ b/drivers/soc/Makefile
@@ -3,7 +3,6 @@
 #
 
 obj-y				+= bcm/
-obj-$(CONFIG_SOC_BRCMSTB)	+= brcmstb/
 obj-$(CONFIG_ARCH_DOVE)		+= dove/
 obj-$(CONFIG_MACH_DOVE)		+= dove/
 obj-y				+= fsl/
diff --git a/drivers/soc/bcm/Kconfig b/drivers/soc/bcm/Kconfig
index 3066ede..97156ae 100644
--- a/drivers/soc/bcm/Kconfig
+++ b/drivers/soc/bcm/Kconfig
@@ -1,3 +1,5 @@
+menu "Broadcom SoC drivers"
+
 config RASPBERRYPI_POWER
 	bool "Raspberry Pi power domain driver"
 	depends on ARCH_BCM2835 || COMPILE_TEST
@@ -7,3 +9,16 @@
 	help
 	  This enables support for the RPi power domains which can be enabled
 	  or disabled via the RPi firmware.
+
+config SOC_BRCMSTB
+	bool "Broadcom STB SoC drivers"
+	depends on ARM
+	select SOC_BUS
+	help
+	  Enables drivers for the Broadcom Set-Top Box (STB) series of chips.
+	  This option alone enables only some support code, while the drivers
+	  can be enabled individually within this menu.
+
+	  If unsure, say N.
+
+endmenu
diff --git a/drivers/soc/bcm/Makefile b/drivers/soc/bcm/Makefile
index 63aa3eb..dc4fced 100644
--- a/drivers/soc/bcm/Makefile
+++ b/drivers/soc/bcm/Makefile
@@ -1 +1,2 @@
 obj-$(CONFIG_RASPBERRYPI_POWER)	+= raspberrypi-power.o
+obj-$(CONFIG_SOC_BRCMSTB)	+= brcmstb/
diff --git a/drivers/soc/brcmstb/Makefile b/drivers/soc/bcm/brcmstb/Makefile
similarity index 100%
rename from drivers/soc/brcmstb/Makefile
rename to drivers/soc/bcm/brcmstb/Makefile
diff --git a/drivers/soc/brcmstb/biuctrl.c b/drivers/soc/bcm/brcmstb/biuctrl.c
similarity index 98%
rename from drivers/soc/brcmstb/biuctrl.c
rename to drivers/soc/bcm/brcmstb/biuctrl.c
index 9049c076f..3c39415 100644
--- a/drivers/soc/brcmstb/biuctrl.c
+++ b/drivers/soc/bcm/brcmstb/biuctrl.c
@@ -19,6 +19,7 @@
 #include <linux/io.h>
 #include <linux/of_address.h>
 #include <linux/syscore_ops.h>
+#include <linux/soc/brcmstb/brcmstb.h>
 
 #define CPU_CREDIT_REG_OFFSET			0x184
 #define  CPU_CREDIT_REG_MCPx_WR_PAIRING_EN_MASK	0x70000000
diff --git a/drivers/soc/brcmstb/common.c b/drivers/soc/bcm/brcmstb/common.c
similarity index 100%
rename from drivers/soc/brcmstb/common.c
rename to drivers/soc/bcm/brcmstb/common.c
diff --git a/drivers/soc/brcmstb/Kconfig b/drivers/soc/brcmstb/Kconfig
deleted file mode 100644
index 7fec3b4..0000000
--- a/drivers/soc/brcmstb/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-menuconfig SOC_BRCMSTB
-	bool "Broadcom STB SoC drivers"
-	depends on ARM
-	select SOC_BUS
-	help
-	  Enables drivers for the Broadcom Set-Top Box (STB) series of chips.
-	  This option alone enables only some support code, while the drivers
-	  can be enabled individually within this menu.
-
-	  If unsure, say N.
diff --git a/drivers/soc/qcom/smem_state.c b/drivers/soc/qcom/smem_state.c
index 54261de..d5437ca 100644
--- a/drivers/soc/qcom/smem_state.c
+++ b/drivers/soc/qcom/smem_state.c
@@ -104,26 +104,26 @@
 
 	if (con_id) {
 		index = of_property_match_string(dev->of_node,
-						 "qcom,state-names",
+						 "qcom,smem-state-names",
 						 con_id);
 		if (index < 0) {
-			dev_err(dev, "missing qcom,state-names\n");
+			dev_err(dev, "missing qcom,smem-state-names\n");
 			return ERR_PTR(index);
 		}
 	}
 
 	ret = of_parse_phandle_with_args(dev->of_node,
-					 "qcom,state",
-					 "#qcom,state-cells",
+					 "qcom,smem-states",
+					 "#qcom,smem-state-cells",
 					 index,
 					 &args);
 	if (ret) {
-		dev_err(dev, "failed to parse qcom,state property\n");
+		dev_err(dev, "failed to parse qcom,smem-states property\n");
 		return ERR_PTR(ret);
 	}
 
 	if (args.args_count != 1) {
-		dev_err(dev, "invalid #qcom,state-cells\n");
+		dev_err(dev, "invalid #qcom,smem-state-cells\n");
 		return ERR_PTR(-EINVAL);
 	}
 
diff --git a/drivers/soc/qcom/smp2p.c b/drivers/soc/qcom/smp2p.c
index f1eed7f..f51fb2e 100644
--- a/drivers/soc/qcom/smp2p.c
+++ b/drivers/soc/qcom/smp2p.c
@@ -196,7 +196,7 @@
 	/* Match newly created entries */
 	for (i = smp2p->valid_entries; i < in->valid_entries; i++) {
 		list_for_each_entry(entry, &smp2p->inbound, node) {
-			memcpy_fromio(buf, in->entries[i].name, sizeof(buf));
+			memcpy(buf, in->entries[i].name, sizeof(buf));
 			if (!strcmp(buf, entry->name)) {
 				entry->value = &in->entries[i].value;
 				break;
@@ -343,12 +343,13 @@
 
 	/* Allocate an entry from the smem item */
 	strlcpy(buf, entry->name, SMP2P_MAX_ENTRY_NAME);
-	memcpy_toio(out->entries[out->valid_entries].name, buf, SMP2P_MAX_ENTRY_NAME);
-	out->valid_entries++;
+	memcpy(out->entries[out->valid_entries].name, buf, SMP2P_MAX_ENTRY_NAME);
 
 	/* Make the logical entry reference the physical value */
 	entry->value = &out->entries[out->valid_entries].value;
 
+	out->valid_entries++;
+
 	entry->state = qcom_smem_state_register(node, &smp2p_state_ops, entry);
 	if (IS_ERR(entry->state)) {
 		dev_err(smp2p->dev, "failed to register qcom_smem_state\n");
diff --git a/drivers/soc/qcom/smsm.c b/drivers/soc/qcom/smsm.c
index 6b777af..d0337b2 100644
--- a/drivers/soc/qcom/smsm.c
+++ b/drivers/soc/qcom/smsm.c
@@ -495,7 +495,7 @@
 	if (!smsm->hosts)
 		return -ENOMEM;
 
-	local_node = of_find_node_with_property(pdev->dev.of_node, "#qcom,state-cells");
+	local_node = of_find_node_with_property(pdev->dev.of_node, "#qcom,smem-state-cells");
 	if (!local_node) {
 		dev_err(&pdev->dev, "no state entry\n");
 		return -EINVAL;
diff --git a/drivers/soc/qcom/wcnss_ctrl.c b/drivers/soc/qcom/wcnss_ctrl.c
index c544f3d..520aedd 100644
--- a/drivers/soc/qcom/wcnss_ctrl.c
+++ b/drivers/soc/qcom/wcnss_ctrl.c
@@ -1,4 +1,5 @@
 /*
+ * Copyright (c) 2016, Linaro Ltd.
  * Copyright (c) 2015, Sony Mobile Communications Inc.
  *
  * This program is free software; you can redistribute it and/or modify
@@ -14,8 +15,16 @@
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/soc/qcom/smd.h>
+#include <linux/io.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/soc/qcom/wcnss_ctrl.h>
 
 #define WCNSS_REQUEST_TIMEOUT	(5 * HZ)
+#define WCNSS_CBC_TIMEOUT	(10 * HZ)
+
+#define WCNSS_ACK_DONE_BOOTING	1
+#define WCNSS_ACK_COLD_BOOTING	2
 
 #define NV_FRAGMENT_SIZE	3072
 #define NVBIN_FILE		"wlan/prima/WCNSS_qcom_wlan_nv.bin"
@@ -25,17 +34,19 @@
  * @dev:	device handle
  * @channel:	SMD channel handle
  * @ack:	completion for outstanding requests
+ * @cbc:	completion for cbc complete indication
  * @ack_status:	status of the outstanding request
- * @download_nv_work: worker for uploading nv binary
+ * @probe_work: worker for uploading nv binary
  */
 struct wcnss_ctrl {
 	struct device *dev;
 	struct qcom_smd_channel *channel;
 
 	struct completion ack;
+	struct completion cbc;
 	int ack_status;
 
-	struct work_struct download_nv_work;
+	struct work_struct probe_work;
 };
 
 /* message types */
@@ -48,6 +59,11 @@
 	WCNSS_UPLOAD_CAL_RESP,
 	WCNSS_DOWNLOAD_CAL_REQ,
 	WCNSS_DOWNLOAD_CAL_RESP,
+	WCNSS_VBAT_LEVEL_IND,
+	WCNSS_BUILD_VERSION_REQ,
+	WCNSS_BUILD_VERSION_RESP,
+	WCNSS_PM_CONFIG_REQ,
+	WCNSS_CBC_COMPLETE_IND,
 };
 
 /**
@@ -128,7 +144,7 @@
 			 version->major, version->minor,
 			 version->version, version->revision);
 
-		schedule_work(&wcnss->download_nv_work);
+		complete(&wcnss->ack);
 		break;
 	case WCNSS_DOWNLOAD_NV_RESP:
 		if (count != sizeof(*nvresp)) {
@@ -141,6 +157,10 @@
 		wcnss->ack_status = nvresp->status;
 		complete(&wcnss->ack);
 		break;
+	case WCNSS_CBC_COMPLETE_IND:
+		dev_dbg(wcnss->dev, "cold boot complete\n");
+		complete(&wcnss->cbc);
+		break;
 	default:
 		dev_info(wcnss->dev, "unknown message type %d\n", hdr->type);
 		break;
@@ -156,20 +176,32 @@
 static int wcnss_request_version(struct wcnss_ctrl *wcnss)
 {
 	struct wcnss_msg_hdr msg;
+	int ret;
 
 	msg.type = WCNSS_VERSION_REQ;
 	msg.len = sizeof(msg);
+	ret = qcom_smd_send(wcnss->channel, &msg, sizeof(msg));
+	if (ret < 0)
+		return ret;
 
-	return qcom_smd_send(wcnss->channel, &msg, sizeof(msg));
+	ret = wait_for_completion_timeout(&wcnss->ack, WCNSS_CBC_TIMEOUT);
+	if (!ret) {
+		dev_err(wcnss->dev, "timeout waiting for version response\n");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
 }
 
 /**
  * wcnss_download_nv() - send nv binary to WCNSS
- * @work:	work struct to acquire wcnss context
+ * @wcnss:	wcnss_ctrl state handle
+ * @expect_cbc:	indicator to caller that an cbc event is expected
+ *
+ * Returns 0 on success. Negative errno on failure.
  */
-static void wcnss_download_nv(struct work_struct *work)
+static int wcnss_download_nv(struct wcnss_ctrl *wcnss, bool *expect_cbc)
 {
-	struct wcnss_ctrl *wcnss = container_of(work, struct wcnss_ctrl, download_nv_work);
 	struct wcnss_download_nv_req *req;
 	const struct firmware *fw;
 	const void *data;
@@ -178,10 +210,10 @@
 
 	req = kzalloc(sizeof(*req) + NV_FRAGMENT_SIZE, GFP_KERNEL);
 	if (!req)
-		return;
+		return -ENOMEM;
 
 	ret = request_firmware(&fw, NVBIN_FILE, wcnss->dev);
-	if (ret) {
+	if (ret < 0) {
 		dev_err(wcnss->dev, "Failed to load nv file %s: %d\n",
 			NVBIN_FILE, ret);
 		goto free_req;
@@ -207,7 +239,7 @@
 		memcpy(req->fragment, data, req->frag_size);
 
 		ret = qcom_smd_send(wcnss->channel, req, req->hdr.len);
-		if (ret) {
+		if (ret < 0) {
 			dev_err(wcnss->dev, "failed to send smd packet\n");
 			goto release_fw;
 		}
@@ -220,16 +252,58 @@
 	} while (left > 0);
 
 	ret = wait_for_completion_timeout(&wcnss->ack, WCNSS_REQUEST_TIMEOUT);
-	if (!ret)
+	if (!ret) {
 		dev_err(wcnss->dev, "timeout waiting for nv upload ack\n");
-	else if (wcnss->ack_status != 1)
-		dev_err(wcnss->dev, "nv upload response failed err: %d\n",
-			wcnss->ack_status);
+		ret = -ETIMEDOUT;
+	} else {
+		*expect_cbc = wcnss->ack_status == WCNSS_ACK_COLD_BOOTING;
+		ret = 0;
+	}
 
 release_fw:
 	release_firmware(fw);
 free_req:
 	kfree(req);
+
+	return ret;
+}
+
+/**
+ * qcom_wcnss_open_channel() - open additional SMD channel to WCNSS
+ * @wcnss:	wcnss handle, retrieved from drvdata
+ * @name:	SMD channel name
+ * @cb:		callback to handle incoming data on the channel
+ */
+struct qcom_smd_channel *qcom_wcnss_open_channel(void *wcnss, const char *name, qcom_smd_cb_t cb)
+{
+	struct wcnss_ctrl *_wcnss = wcnss;
+
+	return qcom_smd_open_channel(_wcnss->channel, name, cb);
+}
+EXPORT_SYMBOL(qcom_wcnss_open_channel);
+
+static void wcnss_async_probe(struct work_struct *work)
+{
+	struct wcnss_ctrl *wcnss = container_of(work, struct wcnss_ctrl, probe_work);
+	bool expect_cbc;
+	int ret;
+
+	ret = wcnss_request_version(wcnss);
+	if (ret < 0)
+		return;
+
+	ret = wcnss_download_nv(wcnss, &expect_cbc);
+	if (ret < 0)
+		return;
+
+	/* Wait for pending cold boot completion if indicated by the nv downloader */
+	if (expect_cbc) {
+		ret = wait_for_completion_timeout(&wcnss->cbc, WCNSS_REQUEST_TIMEOUT);
+		if (!ret)
+			dev_err(wcnss->dev, "expected cold boot completion\n");
+	}
+
+	of_platform_populate(wcnss->dev->of_node, NULL, NULL, wcnss->dev);
 }
 
 static int wcnss_ctrl_probe(struct qcom_smd_device *sdev)
@@ -244,25 +318,38 @@
 	wcnss->channel = sdev->channel;
 
 	init_completion(&wcnss->ack);
-	INIT_WORK(&wcnss->download_nv_work, wcnss_download_nv);
+	init_completion(&wcnss->cbc);
+	INIT_WORK(&wcnss->probe_work, wcnss_async_probe);
 
 	qcom_smd_set_drvdata(sdev->channel, wcnss);
+	dev_set_drvdata(&sdev->dev, wcnss);
 
-	return wcnss_request_version(wcnss);
+	schedule_work(&wcnss->probe_work);
+
+	return 0;
 }
 
-static const struct qcom_smd_id wcnss_ctrl_smd_match[] = {
-	{ .name = "WCNSS_CTRL" },
+static void wcnss_ctrl_remove(struct qcom_smd_device *sdev)
+{
+	struct wcnss_ctrl *wcnss = qcom_smd_get_drvdata(sdev->channel);
+
+	cancel_work_sync(&wcnss->probe_work);
+	of_platform_depopulate(&sdev->dev);
+}
+
+static const struct of_device_id wcnss_ctrl_of_match[] = {
+	{ .compatible = "qcom,wcnss", },
 	{}
 };
 
 static struct qcom_smd_driver wcnss_ctrl_driver = {
 	.probe = wcnss_ctrl_probe,
+	.remove = wcnss_ctrl_remove,
 	.callback = wcnss_ctrl_smd_callback,
-	.smd_match_table = wcnss_ctrl_smd_match,
 	.driver  = {
 		.name  = "qcom_wcnss_ctrl",
 		.owner = THIS_MODULE,
+		.of_match_table = wcnss_ctrl_of_match,
 	},
 };
 
diff --git a/drivers/soc/renesas/Makefile b/drivers/soc/renesas/Makefile
index 151fcd3..623039c 100644
--- a/drivers/soc/renesas/Makefile
+++ b/drivers/soc/renesas/Makefile
@@ -1,7 +1,9 @@
 obj-$(CONFIG_ARCH_R8A7779)	+= rcar-sysc.o r8a7779-sysc.o
 obj-$(CONFIG_ARCH_R8A7790)	+= rcar-sysc.o r8a7790-sysc.o
 obj-$(CONFIG_ARCH_R8A7791)	+= rcar-sysc.o r8a7791-sysc.o
+obj-$(CONFIG_ARCH_R8A7792)	+= rcar-sysc.o r8a7792-sysc.o
 # R-Car M2-N is identical to R-Car M2-W w.r.t. power domains.
 obj-$(CONFIG_ARCH_R8A7793)	+= rcar-sysc.o r8a7791-sysc.o
 obj-$(CONFIG_ARCH_R8A7794)	+= rcar-sysc.o r8a7794-sysc.o
 obj-$(CONFIG_ARCH_R8A7795)	+= rcar-sysc.o r8a7795-sysc.o
+obj-$(CONFIG_ARCH_R8A7796)	+= rcar-sysc.o r8a7796-sysc.o
diff --git a/drivers/soc/renesas/r8a7792-sysc.c b/drivers/soc/renesas/r8a7792-sysc.c
new file mode 100644
index 0000000..ca7467d
--- /dev/null
+++ b/drivers/soc/renesas/r8a7792-sysc.c
@@ -0,0 +1,34 @@
+/*
+ * Renesas R-Car V2H (R8A7792) System Controller
+ *
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/bug.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <dt-bindings/power/r8a7792-sysc.h>
+
+#include "rcar-sysc.h"
+
+static const struct rcar_sysc_area r8a7792_areas[] __initconst = {
+	{ "always-on",	    0, 0, R8A7792_PD_ALWAYS_ON,	-1, PD_ALWAYS_ON },
+	{ "ca15-scu",	0x180, 0, R8A7792_PD_CA15_SCU,	R8A7792_PD_ALWAYS_ON,
+	  PD_SCU },
+	{ "ca15-cpu0",	 0x40, 0, R8A7792_PD_CA15_CPU0,	R8A7792_PD_CA15_SCU,
+	  PD_CPU_NOCR },
+	{ "ca15-cpu1",	 0x40, 1, R8A7792_PD_CA15_CPU1,	R8A7792_PD_CA15_SCU,
+	  PD_CPU_NOCR },
+	{ "sgx",	 0xc0, 0, R8A7792_PD_SGX,	R8A7792_PD_ALWAYS_ON },
+	{ "imp",	0x140, 0, R8A7792_PD_IMP,	R8A7792_PD_ALWAYS_ON },
+};
+
+const struct rcar_sysc_info r8a7792_sysc_info __initconst = {
+	.areas = r8a7792_areas,
+	.num_areas = ARRAY_SIZE(r8a7792_areas),
+};
diff --git a/drivers/soc/renesas/r8a7796-sysc.c b/drivers/soc/renesas/r8a7796-sysc.c
new file mode 100644
index 0000000..f700c84
--- /dev/null
+++ b/drivers/soc/renesas/r8a7796-sysc.c
@@ -0,0 +1,48 @@
+/*
+ * Renesas R-Car M3-W System Controller
+ *
+ * Copyright (C) 2016 Glider bvba
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/bug.h>
+#include <linux/kernel.h>
+
+#include <dt-bindings/power/r8a7796-sysc.h>
+
+#include "rcar-sysc.h"
+
+static const struct rcar_sysc_area r8a7796_areas[] __initconst = {
+	{ "always-on",	    0, 0, R8A7796_PD_ALWAYS_ON,	-1, PD_ALWAYS_ON },
+	{ "ca57-scu",	0x1c0, 0, R8A7796_PD_CA57_SCU,	R8A7796_PD_ALWAYS_ON,
+	  PD_SCU },
+	{ "ca57-cpu0",	 0x80, 0, R8A7796_PD_CA57_CPU0,	R8A7796_PD_CA57_SCU,
+	  PD_CPU_NOCR },
+	{ "ca57-cpu1",	 0x80, 1, R8A7796_PD_CA57_CPU1,	R8A7796_PD_CA57_SCU,
+	  PD_CPU_NOCR },
+	{ "ca53-scu",	0x140, 0, R8A7796_PD_CA53_SCU,	R8A7796_PD_ALWAYS_ON,
+	  PD_SCU },
+	{ "ca53-cpu0",	0x200, 0, R8A7796_PD_CA53_CPU0,	R8A7796_PD_CA53_SCU,
+	  PD_CPU_NOCR },
+	{ "ca53-cpu1",	0x200, 1, R8A7796_PD_CA53_CPU1,	R8A7796_PD_CA53_SCU,
+	  PD_CPU_NOCR },
+	{ "ca53-cpu2",	0x200, 2, R8A7796_PD_CA53_CPU2,	R8A7796_PD_CA53_SCU,
+	  PD_CPU_NOCR },
+	{ "ca53-cpu3",	0x200, 3, R8A7796_PD_CA53_CPU3,	R8A7796_PD_CA53_SCU,
+	  PD_CPU_NOCR },
+	{ "cr7",	0x240, 0, R8A7796_PD_CR7,	R8A7796_PD_ALWAYS_ON },
+	{ "a3vc",	0x380, 0, R8A7796_PD_A3VC,	R8A7796_PD_ALWAYS_ON },
+	{ "a2vc0",	0x3c0, 0, R8A7796_PD_A2VC0,	R8A7796_PD_A3VC },
+	{ "a2vc1",	0x3c0, 1, R8A7796_PD_A2VC1,	R8A7796_PD_A3VC },
+	{ "3dg-a",	0x100, 0, R8A7796_PD_3DG_A,	R8A7796_PD_ALWAYS_ON },
+	{ "3dg-b",	0x100, 1, R8A7796_PD_3DG_B,	R8A7796_PD_3DG_A },
+	{ "a3ir",	0x180, 0, R8A7796_PD_A3IR,	R8A7796_PD_ALWAYS_ON },
+};
+
+const struct rcar_sysc_info r8a7796_sysc_info __initconst = {
+	.areas = r8a7796_areas,
+	.num_areas = ARRAY_SIZE(r8a7796_areas),
+};
diff --git a/drivers/soc/renesas/rcar-sysc.c b/drivers/soc/renesas/rcar-sysc.c
index 79dbc77..65c8e1e 100644
--- a/drivers/soc/renesas/rcar-sysc.c
+++ b/drivers/soc/renesas/rcar-sysc.c
@@ -164,15 +164,6 @@
 	return false;
 }
 
-void __iomem *rcar_sysc_init(phys_addr_t base)
-{
-	rcar_sysc_base = ioremap_nocache(base, PAGE_SIZE);
-	if (!rcar_sysc_base)
-		panic("unable to ioremap R-Car SYSC hardware block\n");
-
-	return rcar_sysc_base;
-}
-
 struct rcar_sysc_pd {
 	struct generic_pm_domain genpd;
 	struct rcar_sysc_ch ch;
@@ -293,6 +284,9 @@
 #ifdef CONFIG_ARCH_R8A7791
 	{ .compatible = "renesas,r8a7791-sysc", .data = &r8a7791_sysc_info },
 #endif
+#ifdef CONFIG_ARCH_R8A7792
+	{ .compatible = "renesas,r8a7792-sysc", .data = &r8a7792_sysc_info },
+#endif
 #ifdef CONFIG_ARCH_R8A7793
 	/* R-Car M2-N is identical to R-Car M2-W w.r.t. power domains. */
 	{ .compatible = "renesas,r8a7793-sysc", .data = &r8a7791_sysc_info },
@@ -303,6 +297,9 @@
 #ifdef CONFIG_ARCH_R8A7795
 	{ .compatible = "renesas,r8a7795-sysc", .data = &r8a7795_sysc_info },
 #endif
+#ifdef CONFIG_ARCH_R8A7796
+	{ .compatible = "renesas,r8a7796-sysc", .data = &r8a7796_sysc_info },
+#endif
 	{ /* sentinel */ }
 };
 
@@ -322,6 +319,9 @@
 	unsigned int i;
 	int error;
 
+	if (rcar_sysc_base)
+		return 0;
+
 	np = of_find_matching_node_and_match(NULL, rcar_sysc_matches, &match);
 	if (!np)
 		return -ENODEV;
@@ -392,10 +392,35 @@
 		domains->domains[area->isr_bit] = &pd->genpd;
 	}
 
-	of_genpd_add_provider_onecell(np, &domains->onecell_data);
+	error = of_genpd_add_provider_onecell(np, &domains->onecell_data);
 
 out_put:
 	of_node_put(np);
 	return error;
 }
 early_initcall(rcar_sysc_pd_init);
+
+void __init rcar_sysc_init(phys_addr_t base, u32 syscier)
+{
+	u32 syscimr;
+
+	if (!rcar_sysc_pd_init())
+		return;
+
+	rcar_sysc_base = ioremap_nocache(base, PAGE_SIZE);
+
+	/*
+	 * Mask all interrupt sources to prevent the CPU from receiving them.
+	 * Make sure not to clear reserved bits that were set before.
+	 */
+	syscimr = ioread32(rcar_sysc_base + SYSCIMR);
+	syscimr |= syscier;
+	pr_debug("%s: syscimr = 0x%08x\n", __func__, syscimr);
+	iowrite32(syscimr, rcar_sysc_base + SYSCIMR);
+
+	/*
+	 * SYSC needs all interrupt sources enabled to control power.
+	 */
+	pr_debug("%s: syscier = 0x%08x\n", __func__, syscier);
+	iowrite32(syscier, rcar_sysc_base + SYSCIER);
+}
diff --git a/drivers/soc/renesas/rcar-sysc.h b/drivers/soc/renesas/rcar-sysc.h
index 5e76617..77dbe86 100644
--- a/drivers/soc/renesas/rcar-sysc.h
+++ b/drivers/soc/renesas/rcar-sysc.h
@@ -53,6 +53,8 @@
 extern const struct rcar_sysc_info r8a7779_sysc_info;
 extern const struct rcar_sysc_info r8a7790_sysc_info;
 extern const struct rcar_sysc_info r8a7791_sysc_info;
+extern const struct rcar_sysc_info r8a7792_sysc_info;
 extern const struct rcar_sysc_info r8a7794_sysc_info;
 extern const struct rcar_sysc_info r8a7795_sysc_info;
+extern const struct rcar_sysc_info r8a7796_sysc_info;
 #endif /* __SOC_RENESAS_RCAR_SYSC_H__ */
diff --git a/drivers/soc/samsung/Kconfig b/drivers/soc/samsung/Kconfig
index d7fc123..2455339 100644
--- a/drivers/soc/samsung/Kconfig
+++ b/drivers/soc/samsung/Kconfig
@@ -10,4 +10,8 @@
 	bool "Exynos PMU controller driver" if COMPILE_TEST
 	depends on (ARM && ARCH_EXYNOS) || ((ARM || ARM64) && COMPILE_TEST)
 
+config EXYNOS_PM_DOMAINS
+	bool "Exynos PM domains" if COMPILE_TEST
+	depends on PM_GENERIC_DOMAINS || COMPILE_TEST
+
 endif
diff --git a/drivers/soc/samsung/Makefile b/drivers/soc/samsung/Makefile
index f64ac4d..3619f2e 100644
--- a/drivers/soc/samsung/Makefile
+++ b/drivers/soc/samsung/Makefile
@@ -1,2 +1,3 @@
 obj-$(CONFIG_EXYNOS_PMU)	+= exynos-pmu.o exynos3250-pmu.o exynos4-pmu.o \
 					exynos5250-pmu.o exynos5420-pmu.o
+obj-$(CONFIG_EXYNOS_PM_DOMAINS) += pm_domains.o
diff --git a/arch/arm/mach-exynos/pm_domains.c b/drivers/soc/samsung/pm_domains.c
similarity index 85%
rename from arch/arm/mach-exynos/pm_domains.c
rename to drivers/soc/samsung/pm_domains.c
index 875a2ba..f60515e 100644
--- a/arch/arm/mach-exynos/pm_domains.c
+++ b/drivers/soc/samsung/pm_domains.c
@@ -23,9 +23,13 @@
 #include <linux/of_platform.h>
 #include <linux/sched.h>
 
-#define INT_LOCAL_PWR_EN	0x7
 #define MAX_CLK_PER_DOMAIN	4
 
+struct exynos_pm_domain_config {
+	/* Value for LOCAL_PWR_CFG and STATUS fields for each domain */
+	u32 local_pwr_cfg;
+};
+
 /*
  * Exynos specific wrapper around the generic power domain
  */
@@ -38,6 +42,7 @@
 	struct clk *clk[MAX_CLK_PER_DOMAIN];
 	struct clk *pclk[MAX_CLK_PER_DOMAIN];
 	struct clk *asb_clk[MAX_CLK_PER_DOMAIN];
+	u32 local_pwr_cfg;
 };
 
 static int exynos_pd_power(struct generic_pm_domain *domain, bool power_on)
@@ -69,13 +74,13 @@
 		}
 	}
 
-	pwr = power_on ? INT_LOCAL_PWR_EN : 0;
+	pwr = power_on ? pd->local_pwr_cfg : 0;
 	__raw_writel(pwr, base);
 
 	/* Wait max 1ms */
 	timeout = 10;
 
-	while ((__raw_readl(base + 0x4) & INT_LOCAL_PWR_EN) != pwr) {
+	while ((__raw_readl(base + 0x4) & pd->local_pwr_cfg) != pwr) {
 		if (!timeout) {
 			op = (power_on) ? "enable" : "disable";
 			pr_err("Power domain %s %s failed\n", domain->name, op);
@@ -119,14 +124,30 @@
 	return exynos_pd_power(domain, false);
 }
 
+static const struct exynos_pm_domain_config exynos4210_cfg __initconst = {
+	.local_pwr_cfg		= 0x7,
+};
+
+static const struct of_device_id exynos_pm_domain_of_match[] __initconst = {
+	{
+		.compatible = "samsung,exynos4210-pd",
+		.data = &exynos4210_cfg,
+	},
+	{ },
+};
+
 static __init int exynos4_pm_init_power_domain(void)
 {
 	struct device_node *np;
+	const struct of_device_id *match;
 
-	for_each_compatible_node(np, NULL, "samsung,exynos4210-pd") {
+	for_each_matching_node_and_match(np, exynos_pm_domain_of_match, &match) {
+		const struct exynos_pm_domain_config *pm_domain_cfg;
 		struct exynos_pm_domain *pd;
 		int on, i;
 
+		pm_domain_cfg = match->data;
+
 		pd = kzalloc(sizeof(*pd), GFP_KERNEL);
 		if (!pd) {
 			pr_err("%s: failed to allocate memory for domain\n",
@@ -153,6 +174,7 @@
 
 		pd->pd.power_off = exynos_pd_power_off;
 		pd->pd.power_on = exynos_pd_power_on;
+		pd->local_pwr_cfg = pm_domain_cfg->local_pwr_cfg;
 
 		for (i = 0; i < MAX_CLK_PER_DOMAIN; i++) {
 			char clk_name[8];
@@ -185,14 +207,14 @@
 			clk_put(pd->oscclk);
 
 no_clk:
-		on = __raw_readl(pd->base + 0x4) & INT_LOCAL_PWR_EN;
+		on = __raw_readl(pd->base + 0x4) & pd->local_pwr_cfg;
 
 		pm_genpd_init(&pd->pd, NULL, !on);
 		of_genpd_add_provider_simple(np, &pd->pd);
 	}
 
 	/* Assign the child power domains to their parents */
-	for_each_compatible_node(np, NULL, "samsung,exynos4210-pd") {
+	for_each_matching_node(np, exynos_pm_domain_of_match) {
 		struct generic_pm_domain *child_domain, *parent_domain;
 		struct of_phandle_args args;
 
diff --git a/drivers/soc/tegra/pmc.c b/drivers/soc/tegra/pmc.c
index bb17345..71c834f 100644
--- a/drivers/soc/tegra/pmc.c
+++ b/drivers/soc/tegra/pmc.c
@@ -51,6 +51,7 @@
 #define  PMC_CNTRL_CPU_PWRREQ_POLARITY	(1 << 15)  /* CPU pwr req polarity */
 #define  PMC_CNTRL_CPU_PWRREQ_OE	(1 << 16)  /* CPU pwr req enable */
 #define  PMC_CNTRL_INTR_POLARITY	(1 << 17)  /* inverts INTR polarity */
+#define  PMC_CNTRL_MAIN_RST		(1 <<  4)
 
 #define DPD_SAMPLE			0x020
 #define  DPD_SAMPLE_ENABLE		(1 << 0)
@@ -80,6 +81,14 @@
 #define PMC_SENSOR_CTRL_SCRATCH_WRITE	(1 << 2)
 #define PMC_SENSOR_CTRL_ENABLE_RST	(1 << 1)
 
+#define PMC_RST_STATUS			0x1b4
+#define  PMC_RST_STATUS_POR		0
+#define  PMC_RST_STATUS_WATCHDOG	1
+#define  PMC_RST_STATUS_SENSOR		2
+#define  PMC_RST_STATUS_SW_MAIN		3
+#define  PMC_RST_STATUS_LP0		4
+#define  PMC_RST_STATUS_AOTAG		5
+
 #define IO_DPD_REQ			0x1b8
 #define  IO_DPD_REQ_CODE_IDLE		(0 << 30)
 #define  IO_DPD_REQ_CODE_OFF		(1 << 30)
@@ -399,6 +408,7 @@
 disable_clks:
 	tegra_powergate_disable_clocks(pg);
 	usleep_range(10, 20);
+
 powergate_off:
 	tegra_powergate_set(pg->id, false);
 
@@ -436,6 +446,7 @@
 	usleep_range(10, 20);
 	tegra_powergate_reset_deassert(pg);
 	usleep_range(10, 20);
+
 disable_clks:
 	tegra_powergate_disable_clocks(pg);
 
@@ -540,6 +551,9 @@
 	struct tegra_powergate pg;
 	int err;
 
+	if (!tegra_powergate_is_available(id))
+		return -EINVAL;
+
 	pg.id = id;
 	pg.clks = &clk;
 	pg.num_clks = 1;
@@ -638,9 +652,10 @@
 
 	tegra_pmc_writel(value, PMC_SCRATCH0);
 
-	value = tegra_pmc_readl(0);
-	value |= 0x10;
-	tegra_pmc_writel(value, 0);
+	/* reset everything but PMC_SCRATCH0 and PMC_RST_STATUS */
+	value = tegra_pmc_readl(PMC_CNTRL);
+	value |= PMC_CNTRL_MAIN_RST;
+	tegra_pmc_writel(value, PMC_CNTRL);
 
 	return NOTIFY_DONE;
 }
@@ -722,13 +737,14 @@
 err:
 	while (i--)
 		clk_put(pg->clks[i]);
+
 	kfree(pg->clks);
 
 	return err;
 }
 
 static int tegra_powergate_of_get_resets(struct tegra_powergate *pg,
-					 struct device_node *np)
+					 struct device_node *np, bool off)
 {
 	struct reset_control *rst;
 	unsigned int i, count;
@@ -748,6 +764,16 @@
 			err = PTR_ERR(pg->resets[i]);
 			goto error;
 		}
+
+		if (off)
+			err = reset_control_assert(pg->resets[i]);
+		else
+			err = reset_control_deassert(pg->resets[i]);
+
+		if (err) {
+			reset_control_put(pg->resets[i]);
+			goto error;
+		}
 	}
 
 	pg->num_resets = count;
@@ -757,6 +783,7 @@
 error:
 	while (i--)
 		reset_control_put(pg->resets[i]);
+
 	kfree(pg->resets);
 
 	return err;
@@ -765,16 +792,19 @@
 static void tegra_powergate_add(struct tegra_pmc *pmc, struct device_node *np)
 {
 	struct tegra_powergate *pg;
+	int id, err;
 	bool off;
-	int id;
 
 	pg = kzalloc(sizeof(*pg), GFP_KERNEL);
 	if (!pg)
-		goto error;
+		return;
 
 	id = tegra_powergate_lookup(pmc, np->name);
-	if (id < 0)
+	if (id < 0) {
+		dev_err(pmc->dev, "powergate lookup failed for %s: %d\n",
+			np->name, id);
 		goto free_mem;
+	}
 
 	/*
 	 * Clear the bit for this powergate so it cannot be managed
@@ -788,31 +818,64 @@
 	pg->genpd.power_on = tegra_genpd_power_on;
 	pg->pmc = pmc;
 
-	if (tegra_powergate_of_get_clks(pg, np))
-		goto set_available;
-
-	if (tegra_powergate_of_get_resets(pg, np))
-		goto remove_clks;
-
 	off = !tegra_powergate_is_powered(pg->id);
 
+	err = tegra_powergate_of_get_clks(pg, np);
+	if (err < 0) {
+		dev_err(pmc->dev, "failed to get clocks for %s: %d\n",
+			np->name, err);
+		goto set_available;
+	}
+
+	err = tegra_powergate_of_get_resets(pg, np, off);
+	if (err < 0) {
+		dev_err(pmc->dev, "failed to get resets for %s: %d\n",
+			np->name, err);
+		goto remove_clks;
+	}
+
+	if (!IS_ENABLED(CONFIG_PM_GENERIC_DOMAINS))
+		goto power_on_cleanup;
+
+	/*
+	 * FIXME: If XHCI is enabled for Tegra, then power-up the XUSB
+	 * host and super-speed partitions. Once the XHCI driver
+	 * manages the partitions itself this code can be removed. Note
+	 * that we don't register these partitions with the genpd core
+	 * to avoid it from powering down the partitions as they appear
+	 * to be unused.
+	 */
+	if (IS_ENABLED(CONFIG_USB_XHCI_TEGRA) &&
+	    (id == TEGRA_POWERGATE_XUSBA || id == TEGRA_POWERGATE_XUSBC))
+		goto power_on_cleanup;
+
 	pm_genpd_init(&pg->genpd, NULL, off);
 
-	if (of_genpd_add_provider_simple(np, &pg->genpd))
+	err = of_genpd_add_provider_simple(np, &pg->genpd);
+	if (err < 0) {
+		dev_err(pmc->dev, "failed to add genpd provider for %s: %d\n",
+			np->name, err);
 		goto remove_resets;
+	}
 
 	dev_dbg(pmc->dev, "added power domain %s\n", pg->genpd.name);
 
 	return;
 
+power_on_cleanup:
+	if (off)
+		WARN_ON(tegra_powergate_power_up(pg, true));
+
 remove_resets:
 	while (pg->num_resets--)
 		reset_control_put(pg->resets[pg->num_resets]);
+
 	kfree(pg->resets);
 
 remove_clks:
 	while (pg->num_clks--)
 		clk_put(pg->clks[pg->num_clks]);
+
 	kfree(pg->clks);
 
 set_available:
@@ -820,16 +883,20 @@
 
 free_mem:
 	kfree(pg);
-
-error:
-	dev_err(pmc->dev, "failed to create power domain for %s\n", np->name);
 }
 
-static void tegra_powergate_init(struct tegra_pmc *pmc)
+static void tegra_powergate_init(struct tegra_pmc *pmc,
+				 struct device_node *parent)
 {
 	struct device_node *np, *child;
+	unsigned int i;
 
-	np = of_get_child_by_name(pmc->dev->of_node, "powergates");
+	/* Create a bitmap of the available and valid partitions */
+	for (i = 0; i < pmc->soc->num_powergates; i++)
+		if (pmc->soc->powergates[i])
+			set_bit(i, pmc->powergates_available);
+
+	np = of_get_child_by_name(parent, "powergates");
 	if (!np)
 		return;
 
@@ -1205,6 +1272,14 @@
 	struct resource *res;
 	int err;
 
+	/*
+	 * Early initialisation should have configured an initial
+	 * register mapping and setup the soc data pointer. If these
+	 * are not valid then something went badly wrong!
+	 */
+	if (WARN_ON(!pmc->base || !pmc->soc))
+		return -ENODEV;
+
 	err = tegra_pmc_parse_dt(pmc, pdev->dev.of_node);
 	if (err < 0)
 		return err;
@@ -1242,8 +1317,6 @@
 		return err;
 	}
 
-	tegra_powergate_init(pmc);
-
 	mutex_lock(&pmc->powergates_lock);
 	iounmap(pmc->base);
 	pmc->base = base;
@@ -1477,10 +1550,11 @@
 	const struct of_device_id *match;
 	struct device_node *np;
 	struct resource regs;
-	unsigned int i;
 	bool invert;
 	u32 value;
 
+	mutex_init(&pmc->powergates_lock);
+
 	np = of_find_matching_node_and_match(NULL, tegra_pmc_match, &match);
 	if (!np) {
 		/*
@@ -1515,39 +1589,40 @@
 		 */
 		if (of_address_to_resource(np, 0, &regs) < 0) {
 			pr_err("failed to get PMC registers\n");
+			of_node_put(np);
 			return -ENXIO;
 		}
-
-		pmc->soc = match->data;
 	}
 
 	pmc->base = ioremap_nocache(regs.start, resource_size(&regs));
 	if (!pmc->base) {
 		pr_err("failed to map PMC registers\n");
+		of_node_put(np);
 		return -ENXIO;
 	}
 
-	/* Create a bit-map of the available and valid partitions */
-	for (i = 0; i < pmc->soc->num_powergates; i++)
-		if (pmc->soc->powergates[i])
-			set_bit(i, pmc->powergates_available);
+	if (np) {
+		pmc->soc = match->data;
 
-	mutex_init(&pmc->powergates_lock);
+		tegra_powergate_init(pmc, np);
 
-	/*
-	 * Invert the interrupt polarity if a PMC device tree node exists and
-	 * contains the nvidia,invert-interrupt property.
-	 */
-	invert = of_property_read_bool(np, "nvidia,invert-interrupt");
+		/*
+		 * Invert the interrupt polarity if a PMC device tree node
+		 * exists and contains the nvidia,invert-interrupt property.
+		 */
+		invert = of_property_read_bool(np, "nvidia,invert-interrupt");
 
-	value = tegra_pmc_readl(PMC_CNTRL);
+		value = tegra_pmc_readl(PMC_CNTRL);
 
-	if (invert)
-		value |= PMC_CNTRL_INTR_POLARITY;
-	else
-		value &= ~PMC_CNTRL_INTR_POLARITY;
+		if (invert)
+			value |= PMC_CNTRL_INTR_POLARITY;
+		else
+			value &= ~PMC_CNTRL_INTR_POLARITY;
 
-	tegra_pmc_writel(value, PMC_CNTRL);
+		tegra_pmc_writel(value, PMC_CNTRL);
+
+		of_node_put(np);
+	}
 
 	return 0;
 }
diff --git a/drivers/tty/serial/clps711x.c b/drivers/tty/serial/clps711x.c
index 5beafd2..ac13286 100644
--- a/drivers/tty/serial/clps711x.c
+++ b/drivers/tty/serial/clps711x.c
@@ -539,7 +539,7 @@
 }
 
 static const struct of_device_id __maybe_unused clps711x_uart_dt_ids[] = {
-	{ .compatible = "cirrus,clps711x-uart", },
+	{ .compatible = "cirrus,ep7209-uart", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, clps711x_uart_dt_ids);
diff --git a/drivers/video/fbdev/clps711x-fb.c b/drivers/video/fbdev/clps711x-fb.c
index 649b32f..ff56107 100644
--- a/drivers/video/fbdev/clps711x-fb.c
+++ b/drivers/video/fbdev/clps711x-fb.c
@@ -273,7 +273,7 @@
 	}
 
 	cfb->syscon =
-		syscon_regmap_lookup_by_compatible("cirrus,clps711x-syscon1");
+		syscon_regmap_lookup_by_compatible("cirrus,ep7209-syscon1");
 	if (IS_ERR(cfb->syscon)) {
 		ret = PTR_ERR(cfb->syscon);
 		goto out_fb_release;
@@ -376,7 +376,7 @@
 }
 
 static const struct of_device_id clps711x_fb_dt_ids[] = {
-	{ .compatible = "cirrus,clps711x-fb", },
+	{ .compatible = "cirrus,ep7209-fb", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, clps711x_fb_dt_ids);
diff --git a/include/dt-bindings/power/r8a7796-sysc.h b/include/dt-bindings/power/r8a7796-sysc.h
new file mode 100644
index 0000000..5b4daab
--- /dev/null
+++ b/include/dt-bindings/power/r8a7796-sysc.h
@@ -0,0 +1,36 @@
+/*
+ * Copyright (C) 2016 Glider bvba
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+#ifndef __DT_BINDINGS_POWER_R8A7796_SYSC_H__
+#define __DT_BINDINGS_POWER_R8A7796_SYSC_H__
+
+/*
+ * These power domain indices match the numbers of the interrupt bits
+ * representing the power areas in the various Interrupt Registers
+ * (e.g. SYSCISR, Interrupt Status Register)
+ */
+
+#define R8A7796_PD_CA57_CPU0		 0
+#define R8A7796_PD_CA57_CPU1		 1
+#define R8A7796_PD_CA53_CPU0		 5
+#define R8A7796_PD_CA53_CPU1		 6
+#define R8A7796_PD_CA53_CPU2		 7
+#define R8A7796_PD_CA53_CPU3		 8
+#define R8A7796_PD_CA57_SCU		12
+#define R8A7796_PD_CR7			13
+#define R8A7796_PD_A3VC			14
+#define R8A7796_PD_3DG_A		17
+#define R8A7796_PD_3DG_B		18
+#define R8A7796_PD_CA53_SCU		21
+#define R8A7796_PD_A3IR			24
+#define R8A7796_PD_A2VC0		25
+#define R8A7796_PD_A2VC1		26
+
+/* Always-on power area */
+#define R8A7796_PD_ALWAYS_ON		32
+
+#endif /* __DT_BINDINGS_POWER_R8A7796_SYSC_H__ */
diff --git a/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h b/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h
new file mode 100644
index 0000000..524d607
--- /dev/null
+++ b/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h
@@ -0,0 +1,210 @@
+/*
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ * The full GNU General Public License is included in this distribution
+ * in the file called COPYING.
+ *
+ * BSD LICENSE
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *   * Redistributions of source code must retain the above copyright
+ *     notice, this list of conditions and the following disclaimer.
+ *   * Redistributions in binary form must reproduce the above copyright
+ *     notice, this list of conditions and the following disclaimer in
+ *     the documentation and/or other materials provided with the
+ *     distribution.
+ *   * Neither the name of Intel Corporation nor the names of its
+ *     contributors may be used to endorse or promote products derived
+ *     from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
+#define _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
+
+/*	RESET0					*/
+#define RESET_HIU			0
+/*					1	*/
+#define RESET_DOS_RESET			2
+#define RESET_DDR_TOP			3
+#define RESET_DCU_RESET			4
+#define RESET_VIU			5
+#define RESET_AIU			6
+#define RESET_VID_PLL_DIV		7
+/*					8	*/
+#define RESET_PMUX			9
+#define RESET_VENC			10
+#define RESET_ASSIST			11
+#define RESET_AFIFO2			12
+#define RESET_VCBUS			13
+/*					14	*/
+/*					15	*/
+#define RESET_GIC			16
+#define RESET_CAPB3_DECODE		17
+#define RESET_NAND_CAPB3		18
+#define RESET_HDMITX_CAPB3		19
+#define RESET_MALI_CAPB3		20
+#define RESET_DOS_CAPB3			21
+#define RESET_SYS_CPU_CAPB3		22
+#define RESET_CBUS_CAPB3		23
+#define RESET_AHB_CNTL			24
+#define RESET_AHB_DATA			25
+#define RESET_VCBUS_CLK81		26
+#define RESET_MMC			27
+#define RESET_MIPI_0			28
+#define RESET_MIPI_1			29
+#define RESET_MIPI_2			30
+#define RESET_MIPI_3			31
+/*	RESET1					*/
+#define RESET_CPPM			32
+#define RESET_DEMUX			33
+#define RESET_USB_OTG			34
+#define RESET_DDR			35
+#define RESET_AO_RESET			36
+#define RESET_BT656			37
+#define RESET_AHB_SRAM			38
+/*					39	*/
+#define RESET_PARSER			40
+#define RESET_BLKMV			41
+#define RESET_ISA			42
+#define RESET_ETHERNET			43
+#define RESET_SD_EMMC_A			44
+#define RESET_SD_EMMC_B			45
+#define RESET_SD_EMMC_C			46
+#define RESET_ROM_BOOT			47
+#define RESET_SYS_CPU_0			48
+#define RESET_SYS_CPU_1			49
+#define RESET_SYS_CPU_2			50
+#define RESET_SYS_CPU_3			51
+#define RESET_SYS_CPU_CORE_0		52
+#define RESET_SYS_CPU_CORE_1		53
+#define RESET_SYS_CPU_CORE_2		54
+#define RESET_SYS_CPU_CORE_3		55
+#define RESET_SYS_PLL_DIV		56
+#define RESET_SYS_CPU_AXI		57
+#define RESET_SYS_CPU_L2		58
+#define RESET_SYS_CPU_P			59
+#define RESET_SYS_CPU_MBIST		60
+/*					61	*/
+/*					62	*/
+/*					63	*/
+/*	RESET2					*/
+#define RESET_VD_RMEM			64
+#define RESET_AUDIN			65
+#define RESET_HDMI_TX			66
+/*					67	*/
+/*					68	*/
+/*					69	*/
+#define RESET_GE2D			70
+#define RESET_PARSER_REG		71
+#define RESET_PARSER_FETCH		72
+#define RESET_PARSER_CTL		73
+#define RESET_PARSER_TOP		74
+/*					75	*/
+/*					76	*/
+#define RESET_AO_CPU_RESET		77
+#define RESET_MALI			78
+#define RESET_HDMI_SYSTEM_RESET		79
+/*					80-95	*/
+/*	RESET3					*/
+#define RESET_RING_OSCILLATOR		96
+#define RESET_SYS_CPU			97
+#define RESET_EFUSE			98
+#define RESET_SYS_CPU_BVCI		99
+#define RESET_AIFIFO			100
+#define RESET_TVFE			101
+#define RESET_AHB_BRIDGE_CNTL		102
+/*					103	*/
+#define RESET_AUDIO_DAC			104
+#define RESET_DEMUX_TOP			105
+#define RESET_DEMUX_DES			106
+#define RESET_DEMUX_S2P_0		107
+#define RESET_DEMUX_S2P_1		108
+#define RESET_DEMUX_RESET_0		109
+#define RESET_DEMUX_RESET_1		110
+#define RESET_DEMUX_RESET_2		111
+/*					112-127	*/
+/*	RESET4					*/
+/*					128	*/
+/*					129	*/
+/*					130	*/
+/*					131	*/
+#define RESET_DVIN_RESET		132
+#define RESET_RDMA			133
+#define RESET_VENCI			134
+#define RESET_VENCP			135
+/*					136	*/
+#define RESET_VDAC			137
+#define RESET_RTC			138
+/*					139	*/
+#define RESET_VDI6			140
+#define RESET_VENCL			141
+#define RESET_I2C_MASTER_2		142
+#define RESET_I2C_MASTER_1		143
+/*					144-159	*/
+/*	RESET5					*/
+/*					160-191	*/
+/*	RESET6					*/
+#define RESET_PERIPHS_GENERAL		192
+#define RESET_PERIPHS_SPICC		193
+#define RESET_PERIPHS_SMART_CARD	194
+#define RESET_PERIPHS_SAR_ADC		195
+#define RESET_PERIPHS_I2C_MASTER_0	196
+#define RESET_SANA			197
+/*					198	*/
+#define RESET_PERIPHS_STREAM_INTERFACE	199
+#define RESET_PERIPHS_SDIO		200
+#define RESET_PERIPHS_UART_0		201
+#define RESET_PERIPHS_UART_1_2		202
+#define RESET_PERIPHS_ASYNC_0		203
+#define RESET_PERIPHS_ASYNC_1		204
+#define RESET_PERIPHS_SPI_0		205
+#define RESET_PERIPHS_SDHC		206
+#define RESET_UART_SLIP			207
+/*					208-223	*/
+/*	RESET7					*/
+#define RESET_USB_DDR_0			224
+#define RESET_USB_DDR_1			225
+#define RESET_USB_DDR_2			226
+#define RESET_USB_DDR_3			227
+/*					228	*/
+#define RESET_DEVICE_MMC_ARB		229
+/*					230	*/
+#define RESET_VID_LOCK			231
+#define RESET_A9_DMC_PIPEL		232
+/*					233-255	*/
+
+#endif
diff --git a/include/dt-bindings/reset/amlogic,meson8b-reset.h b/include/dt-bindings/reset/amlogic,meson8b-reset.h
new file mode 100644
index 0000000..614aff2
--- /dev/null
+++ b/include/dt-bindings/reset/amlogic,meson8b-reset.h
@@ -0,0 +1,175 @@
+/*
+ * This file is provided under a dual BSD/GPLv2 license.  When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * GPL LICENSE SUMMARY
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see <http://www.gnu.org/licenses/>.
+ * The full GNU General Public License is included in this distribution
+ * in the file called COPYING.
+ *
+ * BSD LICENSE
+ *
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ *   * Redistributions of source code must retain the above copyright
+ *     notice, this list of conditions and the following disclaimer.
+ *   * Redistributions in binary form must reproduce the above copyright
+ *     notice, this list of conditions and the following disclaimer in
+ *     the documentation and/or other materials provided with the
+ *     distribution.
+ *   * Neither the name of Intel Corporation nor the names of its
+ *     contributors may be used to endorse or promote products derived
+ *     from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+#ifndef _DT_BINDINGS_AMLOGIC_MESON8B_RESET_H
+#define _DT_BINDINGS_AMLOGIC_MESON8B_RESET_H
+
+/*	RESET0					*/
+#define RESET_HIU			0
+#define RESET_VLD			1
+#define RESET_IQIDCT			2
+#define RESET_MC			3
+/*					8	*/
+#define RESET_VIU			5
+#define RESET_AIU			6
+#define RESET_MCPU			7
+#define RESET_CCPU			8
+#define RESET_PMUX			9
+#define RESET_VENC			10
+#define RESET_ASSIST			11
+#define RESET_AFIFO2			12
+#define RESET_MDEC			13
+#define RESET_VLD_PART			14
+#define RESET_VIFIFO			15
+/*					16-31	*/
+/*	RESET1					*/
+/*					32	*/
+#define RESET_DEMUX			33
+#define RESET_USB_OTG			34
+#define RESET_DDR			35
+#define RESET_VDAC_1			36
+#define RESET_BT656			37
+#define RESET_AHB_SRAM			38
+#define RESET_AHB_BRIDGE		39
+#define RESET_PARSER			40
+#define RESET_BLKMV			41
+#define RESET_ISA			42
+#define RESET_ETHERNET			43
+#define RESET_ABUF			44
+#define RESET_AHB_DATA			45
+#define RESET_AHB_CNTL			46
+#define RESET_ROM_BOOT			47
+/*					48-63	*/
+/*	RESET2					*/
+#define RESET_VD_RMEM			64
+#define RESET_AUDIN			65
+#define RESET_DBLK			66
+#define RESET_PIC_DC			66
+#define RESET_PSC			66
+#define RESET_NAND			66
+#define RESET_GE2D			70
+#define RESET_PARSER_REG		71
+#define RESET_PARSER_FETCH		72
+#define RESET_PARSER_CTL		73
+#define RESET_PARSER_TOP		74
+#define RESET_HDMI_APB			75
+#define RESET_AUDIO_APB			76
+#define RESET_MEDIA_CPU			77
+#define RESET_MALI			78
+#define RESET_HDMI_SYSTEM_RESET		79
+/*					80-95	*/
+/*	RESET3					*/
+#define RESET_RING_OSCILLATOR		96
+#define RESET_SYS_CPU_0			97
+#define RESET_EFUSE			98
+#define RESET_SYS_CPU_BVCI		99
+#define RESET_AIFIFO			100
+#define RESET_AUDIO_PLL_MODULATOR	101
+#define RESET_AHB_BRIDGE_CNTL		102
+#define RESET_SYS_CPU_1			103
+#define RESET_AUDIO_DAC			104
+#define RESET_DEMUX_TOP			105
+#define RESET_DEMUX_DES			106
+#define RESET_DEMUX_S2P_0		107
+#define RESET_DEMUX_S2P_1		108
+#define RESET_DEMUX_RESET_0		109
+#define RESET_DEMUX_RESET_1		110
+#define RESET_DEMUX_RESET_2		111
+/*					112-127	*/
+/*	RESET4					*/
+#define RESET_PL310			128
+#define RESET_A5_APB			129
+#define RESET_A5_AXI			130
+#define RESET_A5			131
+#define RESET_DVIN			132
+#define RESET_RDMA			133
+#define RESET_VENCI			134
+#define RESET_VENCP			135
+#define RESET_VENCT			136
+#define RESET_VDAC_4			137
+#define RESET_RTC			138
+#define RESET_A5_DEBUG			139
+#define RESET_VDI6			140
+#define RESET_VENCL			141
+/*					142-159	*/
+/*	RESET5					*/
+#define RESET_DDR_PLL			160
+#define RESET_MISC_PLL			161
+#define RESET_SYS_PLL			162
+#define RESET_HPLL_PLL			163
+#define RESET_AUDIO_PLL			164
+#define RESET_VID2_PLL			165
+/*					166-191	*/
+/*	RESET6					*/
+#define RESET_PERIPHS_GENERAL		192
+#define RESET_PERIPHS_IR_REMOTE		193
+#define RESET_PERIPHS_SMART_CARD	194
+#define RESET_PERIPHS_SAR_ADC		195
+#define RESET_PERIPHS_I2C_MASTER_0	196
+#define RESET_PERIPHS_I2C_MASTER_1	197
+#define RESET_PERIPHS_I2C_SLAVE		198
+#define RESET_PERIPHS_STREAM_INTERFACE	199
+#define RESET_PERIPHS_SDIO		200
+#define RESET_PERIPHS_UART_0		201
+#define RESET_PERIPHS_UART_1		202
+#define RESET_PERIPHS_ASYNC_0		203
+#define RESET_PERIPHS_ASYNC_1		204
+#define RESET_PERIPHS_SPI_0		205
+#define RESET_PERIPHS_SPI_1		206
+#define RESET_PERIPHS_LED_PWM		207
+/*					208-223	*/
+/*	RESET7					*/
+/*					224-255	*/
+
+#endif
diff --git a/include/dt-bindings/reset/hisi,hi6220-resets.h b/include/dt-bindings/reset/hisi,hi6220-resets.h
index ca08a7e..322ec53 100644
--- a/include/dt-bindings/reset/hisi,hi6220-resets.h
+++ b/include/dt-bindings/reset/hisi,hi6220-resets.h
@@ -64,4 +64,12 @@
 #define PERIPH_RSDIST9_CARM_SOCDBG      0x507
 #define PERIPH_RSDIST9_CARM_ETM         0x508
 
+#define MEDIA_G3D                       0
+#define MEDIA_CODEC_VPU                 2
+#define MEDIA_CODEC_JPEG                3
+#define MEDIA_ISP                       4
+#define MEDIA_ADE                       5
+#define MEDIA_MMU                       6
+#define MEDIA_XG2RAM1                   7
+
 #endif /*_DT_BINDINGS_RESET_CONTROLLER_HI6220*/
diff --git a/include/dt-bindings/reset/ti-syscon.h b/include/dt-bindings/reset/ti-syscon.h
new file mode 100644
index 0000000..884fd91
--- /dev/null
+++ b/include/dt-bindings/reset/ti-syscon.h
@@ -0,0 +1,38 @@
+/*
+ * TI Syscon Reset definitions
+ *
+ * Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __DT_BINDINGS_RESET_TI_SYSCON_H__
+#define __DT_BINDINGS_RESET_TI_SYSCON_H__
+
+/*
+ * The reset does not support the feature and corresponding
+ * values are not valid
+ */
+#define ASSERT_NONE	(1 << 0)
+#define DEASSERT_NONE	(1 << 1)
+#define STATUS_NONE	(1 << 2)
+
+/* When set this function is activated by setting(vs clearing) this bit */
+#define ASSERT_SET	(1 << 3)
+#define DEASSERT_SET	(1 << 4)
+#define STATUS_SET	(1 << 5)
+
+/* The following are the inverse of the above and are added for consistency */
+#define ASSERT_CLEAR	(0 << 3)
+#define DEASSERT_CLEAR	(0 << 4)
+#define STATUS_CLEAR	(0 << 5)
+
+#endif
diff --git a/include/linux/of_reserved_mem.h b/include/linux/of_reserved_mem.h
index ad2f670..1779cda 100644
--- a/include/linux/of_reserved_mem.h
+++ b/include/linux/of_reserved_mem.h
@@ -1,7 +1,8 @@
 #ifndef __OF_RESERVED_MEM_H
 #define __OF_RESERVED_MEM_H
 
-struct device;
+#include <linux/device.h>
+
 struct of_phandle_args;
 struct reserved_mem_ops;
 
@@ -28,14 +29,17 @@
 	_OF_DECLARE(reservedmem, name, compat, init, reservedmem_of_init_fn)
 
 #ifdef CONFIG_OF_RESERVED_MEM
-int of_reserved_mem_device_init(struct device *dev);
+
+int of_reserved_mem_device_init_by_idx(struct device *dev,
+				       struct device_node *np, int idx);
 void of_reserved_mem_device_release(struct device *dev);
 
 void fdt_init_reserved_mem(void);
 void fdt_reserved_mem_save_node(unsigned long node, const char *uname,
 			       phys_addr_t base, phys_addr_t size);
 #else
-static inline int of_reserved_mem_device_init(struct device *dev)
+static inline int of_reserved_mem_device_init_by_idx(struct device *dev,
+					struct device_node *np, int idx)
 {
 	return -ENOSYS;
 }
@@ -46,4 +50,19 @@
 		const char *uname, phys_addr_t base, phys_addr_t size) { }
 #endif
 
+/**
+ * of_reserved_mem_device_init() - assign reserved memory region to given device
+ * @dev:	Pointer to the device to configure
+ *
+ * This function assigns respective DMA-mapping operations based on the first
+ * reserved memory region specified by 'memory-region' property in device tree
+ * node of the given device.
+ *
+ * Returns error code or zero on success.
+ */
+static inline int of_reserved_mem_device_init(struct device *dev)
+{
+	return of_reserved_mem_device_init_by_idx(dev, dev->of_node, 0);
+}
+
 #endif /* __OF_RESERVED_MEM_H */
diff --git a/include/linux/qcom_scm.h b/include/linux/qcom_scm.h
index 9e12000..cc32ab8 100644
--- a/include/linux/qcom_scm.h
+++ b/include/linux/qcom_scm.h
@@ -29,6 +29,14 @@
 extern int qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt,
 		u32 *resp);
 
+extern bool qcom_scm_pas_supported(u32 peripheral);
+extern int qcom_scm_pas_init_image(u32 peripheral, const void *metadata,
+		size_t size);
+extern int qcom_scm_pas_mem_setup(u32 peripheral, phys_addr_t addr,
+		phys_addr_t size);
+extern int qcom_scm_pas_auth_and_reset(u32 peripheral);
+extern int qcom_scm_pas_shutdown(u32 peripheral);
+
 #define QCOM_SCM_CPU_PWR_DOWN_L2_ON	0x0
 #define QCOM_SCM_CPU_PWR_DOWN_L2_OFF	0x1
 
diff --git a/include/linux/reset-controller.h b/include/linux/reset-controller.h
index b91ba93..db1fe67 100644
--- a/include/linux/reset-controller.h
+++ b/include/linux/reset-controller.h
@@ -53,4 +53,8 @@
 int reset_controller_register(struct reset_controller_dev *rcdev);
 void reset_controller_unregister(struct reset_controller_dev *rcdev);
 
+struct device;
+int devm_reset_controller_register(struct device *dev,
+				   struct reset_controller_dev *rcdev);
+
 #endif
diff --git a/include/linux/reset.h b/include/linux/reset.h
index ec0306ce..5daff15 100644
--- a/include/linux/reset.h
+++ b/include/linux/reset.h
@@ -71,21 +71,21 @@
 					struct device_node *node,
 					const char *id, int index, int shared)
 {
-	return ERR_PTR(-EINVAL);
+	return ERR_PTR(-ENOTSUPP);
 }
 
 static inline struct reset_control *__devm_reset_control_get(
 					struct device *dev,
 					const char *id, int index, int shared)
 {
-	return ERR_PTR(-EINVAL);
+	return ERR_PTR(-ENOTSUPP);
 }
 
 #endif /* CONFIG_RESET_CONTROLLER */
 
 /**
- * reset_control_get - Lookup and obtain an exclusive reference to a
- *                     reset controller.
+ * reset_control_get_exclusive - Lookup and obtain an exclusive reference
+ *                               to a reset controller.
  * @dev: device to be reset by the controller
  * @id: reset line name
  *
@@ -98,8 +98,8 @@
  *
  * Use of id names is optional.
  */
-static inline struct reset_control *__must_check reset_control_get(
-					struct device *dev, const char *id)
+static inline struct reset_control *
+__must_check reset_control_get_exclusive(struct device *dev, const char *id)
 {
 #ifndef CONFIG_RESET_CONTROLLER
 	WARN_ON(1);
@@ -107,12 +107,6 @@
 	return __of_reset_control_get(dev ? dev->of_node : NULL, id, 0, 0);
 }
 
-static inline struct reset_control *reset_control_get_optional(
-					struct device *dev, const char *id)
-{
-	return __of_reset_control_get(dev ? dev->of_node : NULL, id, 0, 0);
-}
-
 /**
  * reset_control_get_shared - Lookup and obtain a shared reference to a
  *                            reset controller.
@@ -141,9 +135,21 @@
 	return __of_reset_control_get(dev ? dev->of_node : NULL, id, 0, 1);
 }
 
+static inline struct reset_control *reset_control_get_optional_exclusive(
+					struct device *dev, const char *id)
+{
+	return __of_reset_control_get(dev ? dev->of_node : NULL, id, 0, 0);
+}
+
+static inline struct reset_control *reset_control_get_optional_shared(
+					struct device *dev, const char *id)
+{
+	return __of_reset_control_get(dev ? dev->of_node : NULL, id, 0, 1);
+}
+
 /**
- * of_reset_control_get - Lookup and obtain an exclusive reference to a
- *                        reset controller.
+ * of_reset_control_get_exclusive - Lookup and obtain an exclusive reference
+ *                                  to a reset controller.
  * @node: device to be reset by the controller
  * @id: reset line name
  *
@@ -151,15 +157,41 @@
  *
  * Use of id names is optional.
  */
-static inline struct reset_control *of_reset_control_get(
+static inline struct reset_control *of_reset_control_get_exclusive(
 				struct device_node *node, const char *id)
 {
 	return __of_reset_control_get(node, id, 0, 0);
 }
 
 /**
- * of_reset_control_get_by_index - Lookup and obtain an exclusive reference to
- *                                 a reset controller by index.
+ * of_reset_control_get_shared - Lookup and obtain an shared reference
+ *                               to a reset controller.
+ * @node: device to be reset by the controller
+ * @id: reset line name
+ *
+ * When a reset-control is shared, the behavior of reset_control_assert /
+ * deassert is changed, the reset-core will keep track of a deassert_count
+ * and only (re-)assert the reset after reset_control_assert has been called
+ * as many times as reset_control_deassert was called. Also see the remark
+ * about shared reset-controls in the reset_control_assert docs.
+ *
+ * Calling reset_control_assert without first calling reset_control_deassert
+ * is not allowed on a shared reset control. Calling reset_control_reset is
+ * also not allowed on a shared reset control.
+ * Returns a struct reset_control or IS_ERR() condition containing errno.
+ *
+ * Use of id names is optional.
+ */
+static inline struct reset_control *of_reset_control_get_shared(
+				struct device_node *node, const char *id)
+{
+	return __of_reset_control_get(node, id, 0, 1);
+}
+
+/**
+ * of_reset_control_get_exclusive_by_index - Lookup and obtain an exclusive
+ *                                           reference to a reset controller
+ *                                           by index.
  * @node: device to be reset by the controller
  * @index: index of the reset controller
  *
@@ -167,23 +199,55 @@
  * in whatever order. Returns a struct reset_control or IS_ERR() condition
  * containing errno.
  */
-static inline struct reset_control *of_reset_control_get_by_index(
+static inline struct reset_control *of_reset_control_get_exclusive_by_index(
 					struct device_node *node, int index)
 {
 	return __of_reset_control_get(node, NULL, index, 0);
 }
 
 /**
- * devm_reset_control_get - resource managed reset_control_get()
+ * of_reset_control_get_shared_by_index - Lookup and obtain an shared
+ *                                        reference to a reset controller
+ *                                        by index.
+ * @node: device to be reset by the controller
+ * @index: index of the reset controller
+ *
+ * When a reset-control is shared, the behavior of reset_control_assert /
+ * deassert is changed, the reset-core will keep track of a deassert_count
+ * and only (re-)assert the reset after reset_control_assert has been called
+ * as many times as reset_control_deassert was called. Also see the remark
+ * about shared reset-controls in the reset_control_assert docs.
+ *
+ * Calling reset_control_assert without first calling reset_control_deassert
+ * is not allowed on a shared reset control. Calling reset_control_reset is
+ * also not allowed on a shared reset control.
+ * Returns a struct reset_control or IS_ERR() condition containing errno.
+ *
+ * This is to be used to perform a list of resets for a device or power domain
+ * in whatever order. Returns a struct reset_control or IS_ERR() condition
+ * containing errno.
+ */
+static inline struct reset_control *of_reset_control_get_shared_by_index(
+					struct device_node *node, int index)
+{
+	return __of_reset_control_get(node, NULL, index, 1);
+}
+
+/**
+ * devm_reset_control_get_exclusive - resource managed
+ *                                    reset_control_get_exclusive()
  * @dev: device to be reset by the controller
  * @id: reset line name
  *
- * Managed reset_control_get(). For reset controllers returned from this
- * function, reset_control_put() is called automatically on driver detach.
- * See reset_control_get() for more information.
+ * Managed reset_control_get_exclusive(). For reset controllers returned
+ * from this function, reset_control_put() is called automatically on driver
+ * detach.
+ *
+ * See reset_control_get_exclusive() for more information.
  */
-static inline struct reset_control *__must_check devm_reset_control_get(
-					struct device *dev, const char *id)
+static inline struct reset_control *
+__must_check devm_reset_control_get_exclusive(struct device *dev,
+					      const char *id)
 {
 #ifndef CONFIG_RESET_CONTROLLER
 	WARN_ON(1);
@@ -191,27 +255,6 @@
 	return __devm_reset_control_get(dev, id, 0, 0);
 }
 
-static inline struct reset_control *devm_reset_control_get_optional(
-					struct device *dev, const char *id)
-{
-	return __devm_reset_control_get(dev, id, 0, 0);
-}
-
-/**
- * devm_reset_control_get_by_index - resource managed reset_control_get
- * @dev: device to be reset by the controller
- * @index: index of the reset controller
- *
- * Managed reset_control_get(). For reset controllers returned from this
- * function, reset_control_put() is called automatically on driver detach.
- * See reset_control_get() for more information.
- */
-static inline struct reset_control *devm_reset_control_get_by_index(
-					struct device *dev, int index)
-{
-	return __devm_reset_control_get(dev, NULL, index, 0);
-}
-
 /**
  * devm_reset_control_get_shared - resource managed reset_control_get_shared()
  * @dev: device to be reset by the controller
@@ -227,6 +270,36 @@
 	return __devm_reset_control_get(dev, id, 0, 1);
 }
 
+static inline struct reset_control *devm_reset_control_get_optional_exclusive(
+					struct device *dev, const char *id)
+{
+	return __devm_reset_control_get(dev, id, 0, 0);
+}
+
+static inline struct reset_control *devm_reset_control_get_optional_shared(
+					struct device *dev, const char *id)
+{
+	return __devm_reset_control_get(dev, id, 0, 1);
+}
+
+/**
+ * devm_reset_control_get_exclusive_by_index - resource managed
+ *                                             reset_control_get_exclusive()
+ * @dev: device to be reset by the controller
+ * @index: index of the reset controller
+ *
+ * Managed reset_control_get_exclusive(). For reset controllers returned from
+ * this function, reset_control_put() is called automatically on driver
+ * detach.
+ *
+ * See reset_control_get_exclusive() for more information.
+ */
+static inline struct reset_control *
+devm_reset_control_get_exclusive_by_index(struct device *dev, int index)
+{
+	return __devm_reset_control_get(dev, NULL, index, 0);
+}
+
 /**
  * devm_reset_control_get_shared_by_index - resource managed
  * reset_control_get_shared
@@ -237,10 +310,60 @@
  * this function, reset_control_put() is called automatically on driver detach.
  * See reset_control_get_shared() for more information.
  */
-static inline struct reset_control *devm_reset_control_get_shared_by_index(
-					struct device *dev, int index)
+static inline struct reset_control *
+devm_reset_control_get_shared_by_index(struct device *dev, int index)
 {
 	return __devm_reset_control_get(dev, NULL, index, 1);
 }
 
+/*
+ * TEMPORARY calls to use during transition:
+ *
+ *   of_reset_control_get() => of_reset_control_get_exclusive()
+ *
+ * These inline function calls will be removed once all consumers
+ * have been moved over to the new explicit API.
+ */
+static inline struct reset_control *reset_control_get(
+				struct device *dev, const char *id)
+{
+	return reset_control_get_exclusive(dev, id);
+}
+
+static inline struct reset_control *reset_control_get_optional(
+					struct device *dev, const char *id)
+{
+	return reset_control_get_optional_exclusive(dev, id);
+}
+
+static inline struct reset_control *of_reset_control_get(
+				struct device_node *node, const char *id)
+{
+	return of_reset_control_get_exclusive(node, id);
+}
+
+static inline struct reset_control *of_reset_control_get_by_index(
+				struct device_node *node, int index)
+{
+	return of_reset_control_get_exclusive_by_index(node, index);
+}
+
+static inline struct reset_control *devm_reset_control_get(
+				struct device *dev, const char *id)
+{
+	return devm_reset_control_get_exclusive(dev, id);
+}
+
+static inline struct reset_control *devm_reset_control_get_optional(
+				struct device *dev, const char *id)
+{
+	return devm_reset_control_get_optional_exclusive(dev, id);
+
+}
+
+static inline struct reset_control *devm_reset_control_get_by_index(
+				struct device *dev, int index)
+{
+	return devm_reset_control_get_exclusive_by_index(dev, index);
+}
 #endif
diff --git a/include/linux/scpi_protocol.h b/include/linux/scpi_protocol.h
index 35de50a..dc5f989 100644
--- a/include/linux/scpi_protocol.h
+++ b/include/linux/scpi_protocol.h
@@ -70,6 +70,8 @@
 	int (*sensor_get_capability)(u16 *sensors);
 	int (*sensor_get_info)(u16 sensor_id, struct scpi_sensor_info *);
 	int (*sensor_get_value)(u16, u64 *);
+	int (*device_get_power_state)(u16);
+	int (*device_set_power_state)(u16, u8);
 };
 
 #if IS_REACHABLE(CONFIG_ARM_SCPI_PROTOCOL)
diff --git a/include/linux/soc/qcom/wcnss_ctrl.h b/include/linux/soc/qcom/wcnss_ctrl.h
new file mode 100644
index 0000000..a37bc55
--- /dev/null
+++ b/include/linux/soc/qcom/wcnss_ctrl.h
@@ -0,0 +1,8 @@
+#ifndef __WCNSS_CTRL_H__
+#define __WCNSS_CTRL_H__
+
+#include <linux/soc/qcom/smd.h>
+
+struct qcom_smd_channel *qcom_wcnss_open_channel(void *wcnss, const char *name, qcom_smd_cb_t cb);
+
+#endif
diff --git a/include/linux/soc/renesas/rcar-sysc.h b/include/linux/soc/renesas/rcar-sysc.h
index 92fc613..7b8b280 100644
--- a/include/linux/soc/renesas/rcar-sysc.h
+++ b/include/linux/soc/renesas/rcar-sysc.h
@@ -11,6 +11,6 @@
 
 int rcar_sysc_power_down(const struct rcar_sysc_ch *sysc_ch);
 int rcar_sysc_power_up(const struct rcar_sysc_ch *sysc_ch);
-void __iomem *rcar_sysc_init(phys_addr_t base);
+void rcar_sysc_init(phys_addr_t base, u32 syscier);
 
 #endif /* __LINUX_SOC_RENESAS_RCAR_SYSC_H__ */
diff --git a/include/media/videobuf2-dma-contig.h b/include/media/videobuf2-dma-contig.h
index 2087c9a..f7dc840 100644
--- a/include/media/videobuf2-dma-contig.h
+++ b/include/media/videobuf2-dma-contig.h
@@ -35,6 +35,8 @@
 }
 
 void vb2_dma_contig_cleanup_ctx(void *alloc_ctx);
+int vb2_dma_contig_set_max_seg_size(struct device *dev, unsigned int size);
+void vb2_dma_contig_clear_max_seg_size(struct device *dev);
 
 extern const struct vb2_mem_ops vb2_dma_contig_memops;
 
diff --git a/include/soc/tegra/cpuidle.h b/include/soc/tegra/cpuidle.h
index ea04f42..1fae9c7 100644
--- a/include/soc/tegra/cpuidle.h
+++ b/include/soc/tegra/cpuidle.h
@@ -14,7 +14,7 @@
 #ifndef __SOC_TEGRA_CPUIDLE_H__
 #define __SOC_TEGRA_CPUIDLE_H__
 
-#ifdef CONFIG_CPU_IDLE
+#if defined(CONFIG_ARM) && defined(CONFIG_CPU_IDLE)
 void tegra_cpuidle_pcie_irqs_in_use(void);
 #else
 static inline void tegra_cpuidle_pcie_irqs_in_use(void)