cfg80211 API for channels/bitrates, mac80211 and driver conversion
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/net/mac80211/ieee80211.c b/net/mac80211/ieee80211.c
index 3961d4c..de894b6 100644
--- a/net/mac80211/ieee80211.c
+++ b/net/mac80211/ieee80211.c
@@ -876,37 +876,28 @@
int ieee80211_hw_config(struct ieee80211_local *local)
{
- struct ieee80211_hw_mode *mode;
struct ieee80211_channel *chan;
int ret = 0;
- if (local->sta_sw_scanning) {
+ if (local->sta_sw_scanning)
chan = local->scan_channel;
- mode = local->scan_hw_mode;
- } else {
+ else
chan = local->oper_channel;
- mode = local->oper_hw_mode;
- }
- local->hw.conf.channel = chan->chan;
- local->hw.conf.channel_val = chan->val;
- if (!local->hw.conf.power_level) {
- local->hw.conf.power_level = chan->power_level;
- } else {
- local->hw.conf.power_level = min(chan->power_level,
- local->hw.conf.power_level);
- }
- local->hw.conf.freq = chan->freq;
- local->hw.conf.phymode = mode->mode;
- local->hw.conf.antenna_max = chan->antenna_max;
- local->hw.conf.chan = chan;
- local->hw.conf.mode = mode;
+ local->hw.conf.channel = chan;
+
+ if (!local->hw.conf.power_level)
+ local->hw.conf.power_level = chan->max_power;
+ else
+ local->hw.conf.power_level = min(chan->max_power,
+ local->hw.conf.power_level);
+
+ local->hw.conf.max_antenna_gain = chan->max_antenna_gain;
#ifdef CONFIG_MAC80211_VERBOSE_DEBUG
- printk(KERN_DEBUG "HW CONFIG: channel=%d freq=%d "
- "phymode=%d\n", local->hw.conf.channel, local->hw.conf.freq,
- local->hw.conf.phymode);
-#endif /* CONFIG_MAC80211_VERBOSE_DEBUG */
+ printk(KERN_DEBUG "%s: HW CONFIG: freq=%d\n",
+ wiphy_name(local->hw.wiphy), chan->center_freq);
+#endif
if (local->open_count)
ret = local->ops->config(local_to_hw(local), &local->hw.conf);
@@ -924,11 +915,13 @@
struct ieee80211_ht_bss_info *req_bss_cap)
{
struct ieee80211_conf *conf = &local->hw.conf;
- struct ieee80211_hw_mode *mode = conf->mode;
+ struct ieee80211_supported_band *sband;
int i;
+ sband = local->hw.wiphy->bands[conf->channel->band];
+
/* HT is not supported */
- if (!mode->ht_info.ht_supported) {
+ if (!sband->ht_info.ht_supported) {
conf->flags &= ~IEEE80211_CONF_SUPPORT_HT_MODE;
return -EOPNOTSUPP;
}
@@ -938,17 +931,17 @@
conf->flags &= ~IEEE80211_CONF_SUPPORT_HT_MODE;
} else {
conf->flags |= IEEE80211_CONF_SUPPORT_HT_MODE;
- conf->ht_conf.cap = req_ht_cap->cap & mode->ht_info.cap;
+ conf->ht_conf.cap = req_ht_cap->cap & sband->ht_info.cap;
conf->ht_conf.cap &= ~(IEEE80211_HT_CAP_MIMO_PS);
conf->ht_conf.cap |=
- mode->ht_info.cap & IEEE80211_HT_CAP_MIMO_PS;
+ sband->ht_info.cap & IEEE80211_HT_CAP_MIMO_PS;
conf->ht_bss_conf.primary_channel =
req_bss_cap->primary_channel;
conf->ht_bss_conf.bss_cap = req_bss_cap->bss_cap;
conf->ht_bss_conf.bss_op_mode = req_bss_cap->bss_op_mode;
for (i = 0; i < SUPP_MCS_SET_LEN; i++)
conf->ht_conf.supp_mcs_set[i] =
- mode->ht_info.supp_mcs_set[i] &
+ sband->ht_info.supp_mcs_set[i] &
req_ht_cap->supp_mcs_set[i];
/* In STA mode, this gives us indication
@@ -1418,10 +1411,6 @@
local->long_retry_limit = 4;
local->hw.conf.radio_enabled = 1;
- local->enabled_modes = ~0;
-
- INIT_LIST_HEAD(&local->modes_list);
-
INIT_LIST_HEAD(&local->interfaces);
INIT_DELAYED_WORK(&local->scan_work, ieee80211_sta_scan_work);
@@ -1466,6 +1455,25 @@
struct ieee80211_local *local = hw_to_local(hw);
const char *name;
int result;
+ enum ieee80211_band band;
+
+ /*
+ * generic code guarantees at least one band,
+ * set this very early because much code assumes
+ * that hw.conf.channel is assigned
+ */
+ for (band = 0; band < IEEE80211_NUM_BANDS; band++) {
+ struct ieee80211_supported_band *sband;
+
+ sband = local->hw.wiphy->bands[band];
+ if (sband) {
+ /* init channel we're on */
+ local->hw.conf.channel =
+ local->oper_channel =
+ local->scan_channel = &sband->channels[0];
+ break;
+ }
+ }
result = wiphy_register(local->hw.wiphy);
if (result < 0)
@@ -1567,44 +1575,10 @@
}
EXPORT_SYMBOL(ieee80211_register_hw);
-int ieee80211_register_hwmode(struct ieee80211_hw *hw,
- struct ieee80211_hw_mode *mode)
-{
- struct ieee80211_local *local = hw_to_local(hw);
- struct ieee80211_rate *rate;
- int i;
-
- INIT_LIST_HEAD(&mode->list);
- list_add_tail(&mode->list, &local->modes_list);
-
- local->hw_modes |= (1 << mode->mode);
- for (i = 0; i < mode->num_rates; i++) {
- rate = &(mode->rates[i]);
- rate->rate_inv = CHAN_UTIL_RATE_LCM / rate->rate;
- }
- ieee80211_prepare_rates(local, mode);
-
- if (!local->oper_hw_mode) {
- /* Default to this mode */
- local->hw.conf.phymode = mode->mode;
- local->oper_hw_mode = local->scan_hw_mode = mode;
- local->oper_channel = local->scan_channel = &mode->channels[0];
- local->hw.conf.mode = local->oper_hw_mode;
- local->hw.conf.chan = local->oper_channel;
- }
-
- if (!(hw->flags & IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED))
- ieee80211_set_default_regdomain(mode);
-
- return 0;
-}
-EXPORT_SYMBOL(ieee80211_register_hwmode);
-
void ieee80211_unregister_hw(struct ieee80211_hw *hw)
{
struct ieee80211_local *local = hw_to_local(hw);
struct ieee80211_sub_if_data *sdata, *tmp;
- int i;
tasklet_kill(&local->tx_pending_tasklet);
tasklet_kill(&local->tasklet);
@@ -1645,11 +1619,6 @@
rate_control_deinitialize(local);
debugfs_hw_del(local);
- for (i = 0; i < NUM_IEEE80211_MODES; i++) {
- kfree(local->supp_rates[i]);
- kfree(local->basic_rates[i]);
- }
-
if (skb_queue_len(&local->skb_queue)
|| skb_queue_len(&local->skb_queue_unreliable))
printk(KERN_WARNING "%s: skb_queue not empty\n",
@@ -1696,7 +1665,6 @@
}
ieee80211_debugfs_netdev_init();
- ieee80211_regdomain_init();
return 0;