iwlwifi: more status bit factoring
Continue splitting the status bits between transport and op_mode.
All but a few are separated.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/iwlwifi/iwl-mac80211.c b/drivers/net/wireless/iwlwifi/iwl-mac80211.c
index dcf39f8..54d3709 100644
--- a/drivers/net/wireless/iwlwifi/iwl-mac80211.c
+++ b/drivers/net/wireless/iwlwifi/iwl-mac80211.c
@@ -266,7 +266,7 @@
lockdep_assert_held(&priv->mutex);
- if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status)) {
+ if (test_bit(STATUS_EXIT_PENDING, &priv->status)) {
IWL_WARN(priv, "Exit pending; will not bring the NIC up\n");
return -EIO;
}
@@ -297,9 +297,9 @@
return 0;
error:
- set_bit(STATUS_EXIT_PENDING, &priv->shrd->status);
+ set_bit(STATUS_EXIT_PENDING, &priv->status);
iwl_down(priv);
- clear_bit(STATUS_EXIT_PENDING, &priv->shrd->status);
+ clear_bit(STATUS_EXIT_PENDING, &priv->status);
IWL_ERR(priv, "Unable to initialize device.\n");
return ret;
@@ -322,7 +322,7 @@
IWL_DEBUG_INFO(priv, "Start UP work done.\n");
/* Now we should be done, and the READY bit should be set. */
- if (WARN_ON(!test_bit(STATUS_READY, &priv->shrd->status)))
+ if (WARN_ON(!test_bit(STATUS_READY, &priv->status)))
ret = -EIO;
iwlagn_led_enable(priv);
@@ -807,7 +807,7 @@
* mac80211 might WARN if we fail, but due the way we
* (badly) handle hard rfkill, we might fail here
*/
- if (iwl_is_rfkill(priv->shrd))
+ if (iwl_is_rfkill(priv))
ret = 0;
mutex_unlock(&priv->mutex);
@@ -839,12 +839,12 @@
mutex_lock(&priv->mutex);
- if (iwl_is_rfkill(priv->shrd))
+ if (iwl_is_rfkill(priv))
goto out;
- if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status) ||
- test_bit(STATUS_SCANNING, &priv->shrd->status) ||
- test_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->shrd->status))
+ if (test_bit(STATUS_EXIT_PENDING, &priv->status) ||
+ test_bit(STATUS_SCANNING, &priv->status) ||
+ test_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->status))
goto out;
if (!iwl_is_associated_ctx(ctx))
@@ -884,10 +884,10 @@
* at this point, staging_rxon has the
* configuration for channel switch
*/
- set_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->shrd->status);
+ set_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->status);
priv->switch_channel = cpu_to_le16(ch);
if (cfg(priv)->lib->set_channel_switch(priv, ch_switch)) {
- clear_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->shrd->status);
+ clear_bit(STATUS_CHANNEL_SWITCH_PENDING, &priv->status);
priv->switch_channel = 0;
ieee80211_chswitch_done(ctx->vif, false);
}
@@ -954,11 +954,11 @@
mutex_lock(&priv->mutex);
IWL_DEBUG_MAC80211(priv, "enter\n");
- if (test_bit(STATUS_EXIT_PENDING, &priv->shrd->status)) {
+ if (test_bit(STATUS_EXIT_PENDING, &priv->status)) {
IWL_DEBUG_TX(priv, "Aborting flush due to device shutdown\n");
goto done;
}
- if (iwl_is_rfkill(priv->shrd)) {
+ if (iwl_is_rfkill(priv)) {
IWL_DEBUG_TX(priv, "Aborting flush due to RF Kill\n");
goto done;
}
@@ -999,7 +999,7 @@
IWL_DEBUG_MAC80211(priv, "enter\n");
mutex_lock(&priv->mutex);
- if (test_bit(STATUS_SCAN_HW, &priv->shrd->status)) {
+ if (test_bit(STATUS_SCAN_HW, &priv->status)) {
err = -EBUSY;
goto out;
}
@@ -1140,7 +1140,7 @@
IWL_DEBUG_MAC80211(priv, "enter\n");
- if (!iwl_is_ready_rf(priv->shrd)) {
+ if (!iwl_is_ready_rf(priv)) {
IWL_DEBUG_MAC80211(priv, "leave - RF not ready\n");
return -EIO;
}
@@ -1241,7 +1241,7 @@
iwlagn_disable_roc(priv);
- if (!iwl_is_ready_rf(priv->shrd)) {
+ if (!iwl_is_ready_rf(priv)) {
IWL_WARN(priv, "Try to add interface when device not ready\n");
err = -EINVAL;
goto out;
@@ -1365,7 +1365,7 @@
mutex_lock(&priv->mutex);
- if (!ctx->vif || !iwl_is_ready_rf(priv->shrd)) {
+ if (!ctx->vif || !iwl_is_ready_rf(priv)) {
/*
* Huh? But wait ... this can maybe happen when
* we're in the middle of a firmware restart!