serial: add support for ITE 887x chips

Add support for the it887x-chips (PCI) manufactured by ITE.

Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 5e48587..fd76542 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -580,6 +580,138 @@
 	return num_serial;
 }
 
+/*
+ * ITE support by Niels de Vos <niels.devos@wincor-nixdorf.com>
+ *
+ * These chips are available with optionally one parallel port and up to
+ * two serial ports. Unfortunately they all have the same product id.
+ *
+ * Basic configuration is done over a region of 32 I/O ports. The base
+ * ioport is called INTA or INTC, depending on docs/other drivers.
+ *
+ * The region of the 32 I/O ports is configured in POSIO0R...
+ */
+
+/* registers */
+#define ITE_887x_MISCR		0x9c
+#define ITE_887x_INTCBAR	0x78
+#define ITE_887x_UARTBAR	0x7c
+#define ITE_887x_PS0BAR		0x10
+#define ITE_887x_POSIO0		0x60
+
+/* I/O space size */
+#define ITE_887x_IOSIZE		32
+/* I/O space size (bits 26-24; 8 bytes = 011b) */
+#define ITE_887x_POSIO_IOSIZE_8		(3 << 24)
+/* I/O space size (bits 26-24; 32 bytes = 101b) */
+#define ITE_887x_POSIO_IOSIZE_32	(5 << 24)
+/* Decoding speed (1 = slow, 2 = medium, 3 = fast) */
+#define ITE_887x_POSIO_SPEED		(3 << 29)
+/* enable IO_Space bit */
+#define ITE_887x_POSIO_ENABLE		(1 << 31)
+
+static int __devinit pci_ite887x_init(struct pci_dev *dev)
+{
+	/* inta_addr are the configuration addresses of the ITE */
+	static const short inta_addr[] = { 0x2a0, 0x2c0, 0x220, 0x240, 0x1e0,
+							0x200, 0x280, 0 };
+	int ret, i, type;
+	struct resource *iobase = NULL;
+	u32 miscr, uartbar, ioport;
+
+	/* search for the base-ioport */
+	i = 0;
+	while (inta_addr[i] && iobase == NULL) {
+		iobase = request_region(inta_addr[i], ITE_887x_IOSIZE,
+								"ite887x");
+		if (iobase != NULL) {
+			/* write POSIO0R - speed | size | ioport */
+			pci_write_config_dword(dev, ITE_887x_POSIO0,
+				ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
+				ITE_887x_POSIO_IOSIZE_32 | inta_addr[i]);
+			/* write INTCBAR - ioport */
+			pci_write_config_dword(dev, ITE_887x_INTCBAR, inta_addr[i]);
+			ret = inb(inta_addr[i]);
+			if (ret != 0xff) {
+				/* ioport connected */
+				break;
+			}
+			release_region(iobase->start, ITE_887x_IOSIZE);
+			iobase = NULL;
+		}
+		i++;
+	}
+
+	if (!inta_addr[i]) {
+		printk(KERN_ERR "ite887x: could not find iobase\n");
+		return -ENODEV;
+	}
+
+	/* start of undocumented type checking (see parport_pc.c) */
+	type = inb(iobase->start + 0x18) & 0x0f;
+
+	switch (type) {
+	case 0x2:	/* ITE8871 (1P) */
+	case 0xa:	/* ITE8875 (1P) */
+		ret = 0;
+		break;
+	case 0xe:	/* ITE8872 (2S1P) */
+		ret = 2;
+		break;
+	case 0x6:	/* ITE8873 (1S) */
+		ret = 1;
+		break;
+	case 0x8:	/* ITE8874 (2S) */
+		ret = 2;
+		break;
+	default:
+		moan_device("Unknown ITE887x", dev);
+		ret = -ENODEV;
+	}
+
+	/* configure all serial ports */
+	for (i = 0; i < ret; i++) {
+		/* read the I/O port from the device */
+		pci_read_config_dword(dev, ITE_887x_PS0BAR + (0x4 * (i + 1)),
+								&ioport);
+		ioport &= 0x0000FF00;	/* the actual base address */
+		pci_write_config_dword(dev, ITE_887x_POSIO0 + (0x4 * (i + 1)),
+			ITE_887x_POSIO_ENABLE | ITE_887x_POSIO_SPEED |
+			ITE_887x_POSIO_IOSIZE_8 | ioport);
+
+		/* write the ioport to the UARTBAR */
+		pci_read_config_dword(dev, ITE_887x_UARTBAR, &uartbar);
+		uartbar &= ~(0xffff << (16 * i));	/* clear half the reg */
+		uartbar |= (ioport << (16 * i));	/* set the ioport */
+		pci_write_config_dword(dev, ITE_887x_UARTBAR, uartbar);
+
+		/* get current config */
+		pci_read_config_dword(dev, ITE_887x_MISCR, &miscr);
+		/* disable interrupts (UARTx_Routing[3:0]) */
+		miscr &= ~(0xf << (12 - 4 * i));
+		/* activate the UART (UARTx_En) */
+		miscr |= 1 << (23 - i);
+		/* write new config with activated UART */
+		pci_write_config_dword(dev, ITE_887x_MISCR, miscr);
+	}
+
+	if (ret <= 0) {
+		/* the device has no UARTs if we get here */
+		release_region(iobase->start, ITE_887x_IOSIZE);
+	}
+
+	return ret;
+}
+
+static void __devexit pci_ite887x_exit(struct pci_dev *dev)
+{
+	u32 ioport;
+	/* the ioport is bit 0-15 in POSIO0R */
+	pci_read_config_dword(dev, ITE_887x_POSIO0, &ioport);
+	ioport &= 0xffff;
+	release_region(ioport, ITE_887x_IOSIZE);
+}
+
 static int
 pci_default_setup(struct serial_private *priv, struct pciserial_board *board,
 		  struct uart_port *port, int idx)
@@ -653,6 +785,18 @@
 		.setup		= pci_default_setup,
 	},
 	/*
+	 * ITE
+	 */
+	{
+		.vendor		= PCI_VENDOR_ID_ITE,
+		.device		= PCI_DEVICE_ID_ITE_8872,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.init		= pci_ite887x_init,
+		.setup		= pci_default_setup,
+		.exit		= __devexit_p(pci_ite887x_exit),
+	},
+	/*
 	 * Panacom
 	 */
 	{
@@ -933,6 +1077,7 @@
 
 	pbn_b1_2_1250000,
 
+	pbn_b1_bt_1_115200,
 	pbn_b1_bt_2_921600,
 
 	pbn_b1_1_1382400,
@@ -1211,6 +1356,13 @@
 		.uart_offset	= 8,
 	},
 
+	[pbn_b1_bt_1_115200] = {
+		.flags		= FL_BASE1|FL_BASE_BARS,
+		.num_ports	= 1,
+		.base_baud	= 115200,
+		.uart_offset	= 8,
+	},
+
 	[pbn_b1_bt_2_921600] = {
 		.flags		= FL_BASE1|FL_BASE_BARS,
 		.num_ports	= 2,
@@ -2364,6 +2516,13 @@
 	{	PCI_VENDOR_ID_TOPIC, PCI_DEVICE_ID_TOPIC_TP560,
 		PCI_ANY_ID, PCI_ANY_ID, 0, 0,
 		pbn_b0_1_115200 },
+	/*
+	 * ITE
+	 */
+	{	PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0,
+		pbn_b1_bt_1_115200 },
 
 	/*
 	 * IntaShield IS-200