tg3: Track LP advertising
This patch adds code to track the autonegotiation advertisements of the
link partner and report them through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c
index d1681db..924dce5 100644
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -3803,6 +3803,28 @@
return true;
}
+static bool tg3_phy_copper_fetch_rmtadv(struct tg3 *tp, u32 *rmtadv)
+{
+ u32 lpeth = 0;
+
+ if (!(tp->phy_flags & TG3_PHYFLG_10_100_ONLY)) {
+ u32 val;
+
+ if (tg3_readphy(tp, MII_STAT1000, &val))
+ return false;
+
+ lpeth = mii_stat1000_to_ethtool_lpa_t(val);
+ }
+
+ if (tg3_readphy(tp, MII_LPA, rmtadv))
+ return false;
+
+ lpeth |= mii_lpa_to_ethtool_lpa_t(*rmtadv);
+ tp->link_config.rmt_adv = lpeth;
+
+ return true;
+}
+
static int tg3_setup_copper_phy(struct tg3 *tp, int force_reset)
{
int current_link_up;
@@ -3907,6 +3929,7 @@
current_speed = SPEED_INVALID;
current_duplex = DUPLEX_INVALID;
tp->phy_flags &= ~TG3_PHYFLG_MDIX_STATE;
+ tp->link_config.rmt_adv = 0;
if (tp->phy_flags & TG3_PHYFLG_CAPACITIVE_COUPLING) {
err = tg3_phy_auxctl_read(tp,
@@ -3963,8 +3986,7 @@
if (tp->link_config.autoneg == AUTONEG_ENABLE) {
if ((bmcr & BMCR_ANENABLE) &&
tg3_phy_copper_an_config_ok(tp, &lcl_adv) &&
- (tg3_flag(tp, PAUSE_AUTONEG) &&
- !tg3_readphy(tp, MII_LPA, &rmt_adv)))
+ tg3_phy_copper_fetch_rmtadv(tp, &rmt_adv))
current_link_up = 1;
} else {
if (!(bmcr & BMCR_ANENABLE) &&
@@ -4601,6 +4623,9 @@
if (sg_dig_status & SG_DIG_PARTNER_ASYM_PAUSE)
remote_adv |= LPA_1000XPAUSE_ASYM;
+ tp->link_config.rmt_adv =
+ mii_adv_to_ethtool_adv_x(remote_adv);
+
tg3_setup_flow_control(tp, local_adv, remote_adv);
current_link_up = 1;
tp->serdes_counter = 0;
@@ -4672,6 +4697,9 @@
if (rxflags & MR_LP_ADV_ASYM_PAUSE)
remote_adv |= LPA_1000XPAUSE_ASYM;
+ tp->link_config.rmt_adv =
+ mii_adv_to_ethtool_adv_x(remote_adv);
+
tg3_setup_flow_control(tp, local_adv, remote_adv);
current_link_up = 1;
@@ -4754,6 +4782,7 @@
udelay(40);
current_link_up = 0;
+ tp->link_config.rmt_adv = 0;
mac_status = tr32(MAC_STATUS);
if (tg3_flag(tp, HW_AUTONEG))
@@ -4845,6 +4874,7 @@
current_link_up = 0;
current_speed = SPEED_INVALID;
current_duplex = DUPLEX_INVALID;
+ tp->link_config.rmt_adv = 0;
err |= tg3_readphy(tp, MII_BMSR, &bmsr);
err |= tg3_readphy(tp, MII_BMSR, &bmsr);
@@ -4951,6 +4981,9 @@
current_duplex = DUPLEX_FULL;
else
current_duplex = DUPLEX_HALF;
+
+ tp->link_config.rmt_adv =
+ mii_adv_to_ethtool_adv_x(remote_adv);
} else if (!tg3_flag(tp, 5780_CLASS)) {
/* Link is up via parallel detect */
} else {
@@ -10283,9 +10316,10 @@
cmd->advertising |= ADVERTISED_Asym_Pause;
}
}
- if (netif_running(dev)) {
+ if (netif_running(dev) && netif_carrier_ok(dev)) {
ethtool_cmd_speed_set(cmd, tp->link_config.active_speed);
cmd->duplex = tp->link_config.active_duplex;
+ cmd->lp_advertising = tp->link_config.rmt_adv;
if (!(tp->phy_flags & TG3_PHYFLG_ANY_SERDES)) {
if (tp->phy_flags & TG3_PHYFLG_MDIX_STATE)
cmd->eth_tp_mdix = ETH_TP_MDI_X;
diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h
index a2818ef..9d9f634 100644
--- a/drivers/net/ethernet/broadcom/tg3.h
+++ b/drivers/net/ethernet/broadcom/tg3.h
@@ -2698,6 +2698,7 @@
#define DUPLEX_INVALID 0xff
#define AUTONEG_INVALID 0xff
u16 active_speed;
+ u32 rmt_adv;
/* When we go in and out of low power mode we need
* to swap with this state.