ARM: dts: msm: add camera sensor devices for sdm845
Add camera sensor devices support for CSIPHY,CCI,
Image Sensor, Actuator, OIS, EEPROM, Flash. Also,
add pinctrl support for CCI, MCLCK, MSM and PMIC
gpios.
CRs-Fixed: 2020058
Change-Id: I5889163b539c5b379d97c0022ad66112bdf975b2
Signed-off-by: Jigarkumar Zala <jzala@codeaurora.org>
diff --git a/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-cdp.dtsi b/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-cdp.dtsi
new file mode 100644
index 0000000..fce1687
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-cdp.dtsi
@@ -0,0 +1,352 @@
+/*
+ * Copyright (c) 2016-2017, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+&soc {
+ led_flash_rear: qcom,camera-flash@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,camera-flash";
+ qcom,flash-source = <&pmi8998_flash0 &pmi8998_flash1>;
+ qcom,torch-source = <&pmi8998_torch0 &pmi8998_torch1>;
+ qcom,switch-source = <&pmi8998_switch0>;
+ status = "ok";
+ };
+
+ led_flash_front: qcom,camera-flash@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,camera-flash";
+ qcom,flash-source = <&pmi8998_flash2>;
+ qcom,torch-source = <&pmi8998_torch2>;
+ qcom,switch-source = <&pmi8998_switch1>;
+ status = "ok";
+ };
+
+ actuator_regulator: gpio-regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0x0>;
+ regulator-name = "actuator_regulator";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <100>;
+ enable-active-high;
+ gpio = <&tlmm 27 0>;
+ vin-supply = <&pmi8998_bob>;
+ };
+
+ camera_rear_ldo: gpio-regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <0x1>;
+ regulator-name = "camera_rear_ldo";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <135>;
+ enable-active-high;
+ gpio = <&pm8998_gpios 12 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_rear_dvdd_en_default>;
+ vin-supply = <&pm8998_s3>;
+ };
+
+ camera_ldo: gpio-regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <0x2>;
+ regulator-name = "camera_ldo";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <233>;
+ enable-active-high;
+ gpio = <&pm8998_gpios 9 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_dvdd_en_default>;
+ vin-supply = <&pm8998_s3>;
+ };
+};
+
+&cci {
+ actuator_rear: qcom,actuator@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,actuator";
+ qcom,cci-master = <0>;
+ cam_vaf-supply = <&actuator_regulator>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2800000>;
+ qcom,cam-vreg-max-voltage = <2800000>;
+ qcom,cam-vreg-op-mode = <0>;
+ };
+
+ actuator_front: qcom,actuator@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,actuator";
+ qcom,cci-master = <1>;
+ cam_vaf-supply = <&actuator_regulator>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2800000>;
+ qcom,cam-vreg-max-voltage = <2800000>;
+ qcom,cam-vreg-op-mode = <0>;
+ };
+
+ ois_rear: qcom,ois@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,ois";
+ qcom,cci-master = <0>;
+ cam_vaf-supply = <&actuator_regulator>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2800000>;
+ qcom,cam-vreg-max-voltage = <2800000>;
+ qcom,cam-vreg-op-mode = <0>;
+ status = "disabled";
+ };
+
+ eeprom_rear: qcom,eeprom@0 {
+ cell-index = <0>;
+ reg = <0>;
+ compatible = "qcom,eeprom";
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_rear_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_active
+ &cam_sensor_rear_active>;
+ pinctrl-1 = <&cam_sensor_mclk0_suspend
+ &cam_sensor_rear_suspend>;
+ gpios = <&tlmm 13 0>,
+ <&tlmm 80 0>,
+ <&tlmm 79 0>,
+ <&tlmm 27 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-vaf = <3>;
+ qcom,gpio-req-tbl-num = <0 1 2 3>;
+ qcom,gpio-req-tbl-flags = <1 0 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_VANA0",
+ "CAM_VAF";
+ qcom,sensor-position = <0>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ eeprom_rear_aux: qcom,eeprom@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,eeprom";
+ cam_vdig-supply = <&camera_ldo>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
+ qcom,cam-vreg-min-voltage = <1050000 0 3312000>;
+ qcom,cam-vreg-max-voltage = <1050000 0 3600000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_VANA1";
+ qcom,sensor-position = <0>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ eeprom_front: qcom,eeprom@2 {
+ cell-index = <2>;
+ reg = <0x2>;
+ compatible = "qcom,eeprom";
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk1_active
+ &cam_sensor_front_active>;
+ pinctrl-1 = <&cam_sensor_mclk1_suspend
+ &cam_sensor_front_suspend>;
+ gpios = <&tlmm 14 0>,
+ <&tlmm 28 0>,
+ <&tlmm 8 0>,
+ <&tlmm 27 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-vaf = <3>;
+ qcom,gpio-req-tbl-num = <0 1 2 3>;
+ qcom,gpio-req-tbl-flags = <1 0 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_VANA2",
+ "CAM_VAF";
+ qcom,sensor-position = <1>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@0 {
+ cell-index = <0>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x0>;
+ qcom,csiphy-sd-index = <0>;
+ qcom,sensor-position-roll = <90>;
+ qcom,sensor-position-pitch = <0>;
+ qcom,sensor-position-yaw = <180>;
+ qcom,led-flash-src = <&led_flash_rear>;
+ qcom,actuator-src = <&actuator_rear>;
+ qcom,ois-src = <&ois_rear>;
+ qcom,eeprom-src = <&eeprom_rear>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_rear_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_active
+ &cam_sensor_rear_active>;
+ pinctrl-1 = <&cam_sensor_mclk0_suspend
+ &cam_sensor_rear_suspend>;
+ gpios = <&tlmm 13 0>,
+ <&tlmm 80 0>,
+ <&tlmm 79 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_VANA";
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@1 {
+ cell-index = <1>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x1>;
+ qcom,csiphy-sd-index = <1>;
+ qcom,sensor-position-roll = <90>;
+ qcom,sensor-position-pitch = <0>;
+ qcom,sensor-position-yaw = <180>;
+ qcom,eeprom-src = <&eeprom_rear_aux>;
+ cam_vdig-supply = <&camera_ldo>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
+ qcom,cam-vreg-min-voltage = <1050000 0 3312000>;
+ qcom,cam-vreg-max-voltage = <1050000 0 3600000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_VANA1";
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@2 {
+ cell-index = <2>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x02>;
+ qcom,csiphy-sd-index = <2>;
+ qcom,sensor-position-roll = <90>;
+ qcom,sensor-position-pitch = <0>;
+ qcom,sensor-position-yaw = <0>;
+ qcom,eeprom-src = <&eeprom_front>;
+ qcom,actuator-src = <&actuator_front>;
+ qcom,led-flash-src = <&led_flash_front>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk1_active
+ &cam_sensor_front_active>;
+ pinctrl-1 = <&cam_sensor_mclk1_suspend
+ &cam_sensor_front_suspend>;
+ gpios = <&tlmm 14 0>,
+ <&tlmm 28 0>,
+ <&tlmm 8 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_VANA1";
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-mtp.dtsi b/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-mtp.dtsi
new file mode 100644
index 0000000..fce1687
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-camera-sensor-mtp.dtsi
@@ -0,0 +1,352 @@
+/*
+ * Copyright (c) 2016-2017, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+&soc {
+ led_flash_rear: qcom,camera-flash@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,camera-flash";
+ qcom,flash-source = <&pmi8998_flash0 &pmi8998_flash1>;
+ qcom,torch-source = <&pmi8998_torch0 &pmi8998_torch1>;
+ qcom,switch-source = <&pmi8998_switch0>;
+ status = "ok";
+ };
+
+ led_flash_front: qcom,camera-flash@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,camera-flash";
+ qcom,flash-source = <&pmi8998_flash2>;
+ qcom,torch-source = <&pmi8998_torch2>;
+ qcom,switch-source = <&pmi8998_switch1>;
+ status = "ok";
+ };
+
+ actuator_regulator: gpio-regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0x0>;
+ regulator-name = "actuator_regulator";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <100>;
+ enable-active-high;
+ gpio = <&tlmm 27 0>;
+ vin-supply = <&pmi8998_bob>;
+ };
+
+ camera_rear_ldo: gpio-regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <0x1>;
+ regulator-name = "camera_rear_ldo";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <135>;
+ enable-active-high;
+ gpio = <&pm8998_gpios 12 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_rear_dvdd_en_default>;
+ vin-supply = <&pm8998_s3>;
+ };
+
+ camera_ldo: gpio-regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <0x2>;
+ regulator-name = "camera_ldo";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <233>;
+ enable-active-high;
+ gpio = <&pm8998_gpios 9 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&camera_dvdd_en_default>;
+ vin-supply = <&pm8998_s3>;
+ };
+};
+
+&cci {
+ actuator_rear: qcom,actuator@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,actuator";
+ qcom,cci-master = <0>;
+ cam_vaf-supply = <&actuator_regulator>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2800000>;
+ qcom,cam-vreg-max-voltage = <2800000>;
+ qcom,cam-vreg-op-mode = <0>;
+ };
+
+ actuator_front: qcom,actuator@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,actuator";
+ qcom,cci-master = <1>;
+ cam_vaf-supply = <&actuator_regulator>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2800000>;
+ qcom,cam-vreg-max-voltage = <2800000>;
+ qcom,cam-vreg-op-mode = <0>;
+ };
+
+ ois_rear: qcom,ois@0 {
+ cell-index = <0>;
+ reg = <0x0>;
+ compatible = "qcom,ois";
+ qcom,cci-master = <0>;
+ cam_vaf-supply = <&actuator_regulator>;
+ qcom,cam-vreg-name = "cam_vaf";
+ qcom,cam-vreg-min-voltage = <2800000>;
+ qcom,cam-vreg-max-voltage = <2800000>;
+ qcom,cam-vreg-op-mode = <0>;
+ status = "disabled";
+ };
+
+ eeprom_rear: qcom,eeprom@0 {
+ cell-index = <0>;
+ reg = <0>;
+ compatible = "qcom,eeprom";
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_rear_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_active
+ &cam_sensor_rear_active>;
+ pinctrl-1 = <&cam_sensor_mclk0_suspend
+ &cam_sensor_rear_suspend>;
+ gpios = <&tlmm 13 0>,
+ <&tlmm 80 0>,
+ <&tlmm 79 0>,
+ <&tlmm 27 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-vaf = <3>;
+ qcom,gpio-req-tbl-num = <0 1 2 3>;
+ qcom,gpio-req-tbl-flags = <1 0 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_VANA0",
+ "CAM_VAF";
+ qcom,sensor-position = <0>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ eeprom_rear_aux: qcom,eeprom@1 {
+ cell-index = <1>;
+ reg = <0x1>;
+ compatible = "qcom,eeprom";
+ cam_vdig-supply = <&camera_ldo>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
+ qcom,cam-vreg-min-voltage = <1050000 0 3312000>;
+ qcom,cam-vreg-max-voltage = <1050000 0 3600000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_VANA1";
+ qcom,sensor-position = <0>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ eeprom_front: qcom,eeprom@2 {
+ cell-index = <2>;
+ reg = <0x2>;
+ compatible = "qcom,eeprom";
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk1_active
+ &cam_sensor_front_active>;
+ pinctrl-1 = <&cam_sensor_mclk1_suspend
+ &cam_sensor_front_suspend>;
+ gpios = <&tlmm 14 0>,
+ <&tlmm 28 0>,
+ <&tlmm 8 0>,
+ <&tlmm 27 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-vaf = <3>;
+ qcom,gpio-req-tbl-num = <0 1 2 3>;
+ qcom,gpio-req-tbl-flags = <1 0 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_VANA2",
+ "CAM_VAF";
+ qcom,sensor-position = <1>;
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@0 {
+ cell-index = <0>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x0>;
+ qcom,csiphy-sd-index = <0>;
+ qcom,sensor-position-roll = <90>;
+ qcom,sensor-position-pitch = <0>;
+ qcom,sensor-position-yaw = <180>;
+ qcom,led-flash-src = <&led_flash_rear>;
+ qcom,actuator-src = <&actuator_rear>;
+ qcom,ois-src = <&ois_rear>;
+ qcom,eeprom-src = <&eeprom_rear>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_rear_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk0_active
+ &cam_sensor_rear_active>;
+ pinctrl-1 = <&cam_sensor_mclk0_suspend
+ &cam_sensor_rear_suspend>;
+ gpios = <&tlmm 13 0>,
+ <&tlmm 80 0>,
+ <&tlmm 79 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ "CAM_RESET0",
+ "CAM_VANA";
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <0>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@1 {
+ cell-index = <1>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x1>;
+ qcom,csiphy-sd-index = <1>;
+ qcom,sensor-position-roll = <90>;
+ qcom,sensor-position-pitch = <0>;
+ qcom,sensor-position-yaw = <180>;
+ qcom,eeprom-src = <&eeprom_rear_aux>;
+ cam_vdig-supply = <&camera_ldo>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana";
+ qcom,cam-vreg-min-voltage = <1050000 0 3312000>;
+ qcom,cam-vreg-max-voltage = <1050000 0 3600000>;
+ qcom,cam-vreg-op-mode = <105000 0 80000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk2_active
+ &cam_sensor_rear2_active>;
+ pinctrl-1 = <&cam_sensor_mclk2_suspend
+ &cam_sensor_rear2_suspend>;
+ gpios = <&tlmm 15 0>,
+ <&tlmm 9 0>,
+ <&tlmm 8 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
+ "CAM_VANA1";
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+
+ qcom,cam-sensor@2 {
+ cell-index = <2>;
+ compatible = "qcom,cam-sensor";
+ reg = <0x02>;
+ qcom,csiphy-sd-index = <2>;
+ qcom,sensor-position-roll = <90>;
+ qcom,sensor-position-pitch = <0>;
+ qcom,sensor-position-yaw = <0>;
+ qcom,eeprom-src = <&eeprom_front>;
+ qcom,actuator-src = <&actuator_front>;
+ qcom,led-flash-src = <&led_flash_front>;
+ cam_vio-supply = <&pm8998_lvs1>;
+ cam_vana-supply = <&pmi8998_bob>;
+ cam_vdig-supply = <&camera_ldo>;
+ qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig";
+ qcom,cam-vreg-min-voltage = <0 3312000 1050000>;
+ qcom,cam-vreg-max-voltage = <0 3600000 1050000>;
+ qcom,cam-vreg-op-mode = <0 80000 105000>;
+ qcom,gpio-no-mux = <0>;
+ pinctrl-names = "cam_default", "cam_suspend";
+ pinctrl-0 = <&cam_sensor_mclk1_active
+ &cam_sensor_front_active>;
+ pinctrl-1 = <&cam_sensor_mclk1_suspend
+ &cam_sensor_front_suspend>;
+ gpios = <&tlmm 14 0>,
+ <&tlmm 28 0>,
+ <&tlmm 8 0>;
+ qcom,gpio-reset = <1>;
+ qcom,gpio-vana = <2>;
+ qcom,gpio-req-tbl-num = <0 1 2>;
+ qcom,gpio-req-tbl-flags = <1 0 0>;
+ qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ "CAM_RESET2",
+ "CAM_VANA1";
+ qcom,sensor-mode = <0>;
+ qcom,cci-master = <1>;
+ status = "ok";
+ clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+ clock-names = "cam_clk";
+ qcom,clock-rates = <24000000>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-camera.dtsi b/arch/arm64/boot/dts/qcom/sdm845-camera.dtsi
index c197d65..cd9c8a8 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-camera.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-camera.dtsi
@@ -16,4 +16,213 @@
compatible = "qcom,cam-req-mgr";
status = "ok";
};
+
+ qcom,csiphy@ac65000 {
+ cell-index = <0>;
+ compatible = "qcom,csiphy-v1.0", "qcom,csiphy";
+ reg = <0x0ac65000 0x1000>;
+ reg-names = "csiphy";
+ interrupts = <0 477 0>;
+ interrupt-names = "csiphy";
+ gdscr-supply = <&titan_top_gdsc>;
+ qcom,cam-vreg-name = "gdscr";
+ qcom,csi-vdd-voltage = <1200000>;
+ qcom,mipi-csi-vdd-supply = <&pm8998_l26>;
+ clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&clock_camcc CAM_CC_SOC_AHB_CLK>,
+ <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+ <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
+ <&clock_camcc CAM_CC_CSIPHY0_CLK>,
+ <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>,
+ <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>,
+ <&clock_camcc CAM_CC_IFE_0_CSID_CLK>,
+ <&clock_camcc CAM_CC_IFE_0_CSID_CLK_SRC>;
+ clock-names = "camnoc_axi_clk",
+ "soc_ahb_clk",
+ "slow_ahb_src_clk",
+ "cpas_ahb_clk",
+ "cphy_rx_clk_src",
+ "csiphy0_clk",
+ "csi0phytimer_clk_src",
+ "csi0phytimer_clk",
+ "ife_0_csid_clk",
+ "ife_0_csid_clk_src";
+ qcom,clock-rates =
+ <0 0 80000000 0 320000000 0 269333333 0 0 384000000>;
+ status = "ok";
+ };
+
+ qcom,csiphy@ac66000{
+ cell-index = <1>;
+ compatible = "qcom,csiphy-v1.0", "qcom,csiphy";
+ reg = <0xac66000 0x1000>;
+ reg-names = "csiphy";
+ interrupts = <0 478 0>;
+ interrupt-names = "csiphy";
+ gdscr-supply = <&titan_top_gdsc>;
+ qcom,cam-vreg-name = "gdscr";
+ qcom,csi-vdd-voltage = <1200000>;
+ qcom,mipi-csi-vdd-supply = <&pm8998_l26>;
+ clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&clock_camcc CAM_CC_SOC_AHB_CLK>,
+ <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+ <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
+ <&clock_camcc CAM_CC_CSIPHY1_CLK>,
+ <&clock_camcc CAM_CC_CSI1PHYTIMER_CLK_SRC>,
+ <&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>,
+ <&clock_camcc CAM_CC_IFE_1_CSID_CLK>,
+ <&clock_camcc CAM_CC_IFE_1_CSID_CLK_SRC>;
+ clock-names = "camnoc_axi_clk",
+ "soc_ahb_clk",
+ "slow_ahb_src_clk",
+ "cpas_ahb_clk",
+ "cphy_rx_clk_src",
+ "csiphy1_clk",
+ "csi1phytimer_clk_src",
+ "csi1phytimer_clk",
+ "ife_1_csid_clk",
+ "ife_1_csid_clk_src";
+ qcom,clock-rates =
+ <0 0 80000000 0 320000000 0 269333333 0 0 384000000>;
+
+ status = "ok";
+ };
+
+ qcom,csiphy@ac67000 {
+ cell-index = <2>;
+ compatible = "qcom,csiphy-v1.0", "qcom,csiphy";
+ reg = <0xac67000 0x1000>;
+ reg-names = "csiphy";
+ interrupts = <0 479 0>;
+ interrupt-names = "csiphy";
+ gdscr-supply = <&titan_top_gdsc>;
+ qcom,cam-vreg-name = "gdscr";
+ qcom,csi-vdd-voltage = <1200000>;
+ qcom,mipi-csi-vdd-supply = <&pm8998_l26>;
+ clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&clock_camcc CAM_CC_SOC_AHB_CLK>,
+ <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+ <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
+ <&clock_camcc CAM_CC_CSIPHY2_CLK>,
+ <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK_SRC>,
+ <&clock_camcc CAM_CC_CSI2PHYTIMER_CLK>,
+ <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK>,
+ <&clock_camcc CAM_CC_IFE_LITE_CSID_CLK_SRC>;
+ clock-names = "camnoc_axi_clk",
+ "soc_ahb_clk",
+ "slow_ahb_src_clk",
+ "cpas_ahb_clk",
+ "cphy_rx_clk_src",
+ "csiphy2_clk",
+ "csi2phytimer_clk_src",
+ "csi2phytimer_clk",
+ "ife_lite_csid_clk",
+ "ife_lite_csid_clk_src";
+ qcom,clock-rates =
+ <0 0 80000000 0 320000000 0 269333333 0 0 384000000>;
+ status = "ok";
+ };
+
+ cci: qcom,cci@ac4a000 {
+ cell-index = <0>;
+ compatible = "qcom,cci";
+ reg = <0xac4a000 0x4000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg-names = "cci";
+ interrupts = <0 460 0>;
+ interrupt-names = "cci";
+ status = "ok";
+ gdscr-supply = <&titan_top_gdsc>;
+ qcom,cam-vreg-name = "gdscr";
+ clocks = <&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
+ <&clock_camcc CAM_CC_SOC_AHB_CLK>,
+ <&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+ <&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+ <&clock_camcc CAM_CC_CCI_CLK>,
+ <&clock_camcc CAM_CC_CCI_CLK_SRC>;
+ clock-names = "camnoc_axi_clk",
+ "soc_ahb_clk",
+ "slow_ahb_src_clk",
+ "cpas_ahb_clk",
+ "cci_clk",
+ "cci_clk_src";
+ qcom,clock-rates = <0 0 80000000 0 0 37500000>;
+ pinctrl-names = "cci_default", "cci_suspend";
+ pinctrl-0 = <&cci0_active &cci1_active>;
+ pinctrl-1 = <&cci0_suspend &cci1_suspend>;
+ gpios = <&tlmm 17 0>,
+ <&tlmm 18 0>,
+ <&tlmm 19 0>,
+ <&tlmm 20 0>;
+ qcom,gpio-tbl-num = <0 1 2 3>;
+ qcom,gpio-tbl-flags = <1 1 1 1>;
+ qcom,gpio-tbl-label = "CCI_I2C_DATA0",
+ "CCI_I2C_CLK0",
+ "CCI_I2C_DATA1",
+ "CCI_I2C_CLK1";
+
+ i2c_freq_100Khz: qcom,i2c_standard_mode {
+ qcom,hw-thigh = <201>;
+ qcom,hw-tlow = <174>;
+ qcom,hw-tsu-sto = <204>;
+ qcom,hw-tsu-sta = <231>;
+ qcom,hw-thd-dat = <22>;
+ qcom,hw-thd-sta = <162>;
+ qcom,hw-tbuf = <227>;
+ qcom,hw-scl-stretch-en = <0>;
+ qcom,hw-trdhld = <6>;
+ qcom,hw-tsp = <3>;
+ qcom,cci-clk-src = <37500000>;
+ status = "ok";
+ };
+
+ i2c_freq_400Khz: qcom,i2c_fast_mode {
+ qcom,hw-thigh = <38>;
+ qcom,hw-tlow = <56>;
+ qcom,hw-tsu-sto = <40>;
+ qcom,hw-tsu-sta = <40>;
+ qcom,hw-thd-dat = <22>;
+ qcom,hw-thd-sta = <35>;
+ qcom,hw-tbuf = <62>;
+ qcom,hw-scl-stretch-en = <0>;
+ qcom,hw-trdhld = <6>;
+ qcom,hw-tsp = <3>;
+ qcom,cci-clk-src = <37500000>;
+ status = "ok";
+ };
+
+ i2c_freq_custom: qcom,i2c_custom_mode {
+ qcom,hw-thigh = <38>;
+ qcom,hw-tlow = <56>;
+ qcom,hw-tsu-sto = <40>;
+ qcom,hw-tsu-sta = <40>;
+ qcom,hw-thd-dat = <22>;
+ qcom,hw-thd-sta = <35>;
+ qcom,hw-tbuf = <62>;
+ qcom,hw-scl-stretch-en = <1>;
+ qcom,hw-trdhld = <6>;
+ qcom,hw-tsp = <3>;
+ qcom,cci-clk-src = <37500000>;
+ status = "ok";
+ };
+
+ i2c_freq_1Mhz: qcom,i2c_fast_plus_mode {
+ qcom,hw-thigh = <16>;
+ qcom,hw-tlow = <22>;
+ qcom,hw-tsu-sto = <17>;
+ qcom,hw-tsu-sta = <18>;
+ qcom,hw-thd-dat = <16>;
+ qcom,hw-thd-sta = <15>;
+ qcom,hw-tbuf = <24>;
+ qcom,hw-scl-stretch-en = <0>;
+ qcom,hw-trdhld = <3>;
+ qcom,hw-tsp = <3>;
+ qcom,cci-clk-src = <37500000>;
+ status = "ok";
+ };
+ };
};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-cdp.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cdp.dtsi
index 7f9351d..96ce5a8 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-cdp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-cdp.dtsi
@@ -11,7 +11,7 @@
*/
#include <dt-bindings/gpio/gpio.h>
-
+#include "sdm845-camera-sensor-cdp.dtsi"
&soc {
sound-tavil {
qcom,us-euro-gpios = <&tavil_us_euro_sw>;
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi b/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi
index f7da384..e36ccf2 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dtsi
@@ -11,7 +11,7 @@
*/
#include <dt-bindings/gpio/gpio.h>
-
+#include "sdm845-camera-sensor-mtp.dtsi"
&soc {
gpio_keys {
compatible = "gpio-keys";
diff --git a/arch/arm64/boot/dts/qcom/sdm845-pinctrl.dtsi b/arch/arm64/boot/dts/qcom/sdm845-pinctrl.dtsi
index a5ed9aa..bd09c7c 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-pinctrl.dtsi
@@ -2285,6 +2285,231 @@
};
};
};
+
+ cci0_active: cci0_active {
+ mux {
+ /* CLK, DATA */
+ pins = "gpio17","gpio18"; // Only 2
+ function = "cci_i2c";
+ };
+
+ config {
+ pins = "gpio17","gpio18";
+ bias-pull-up; /* PULL UP*/
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cci0_suspend: cci0_suspend {
+ mux {
+ /* CLK, DATA */
+ pins = "gpio17","gpio18";
+ function = "cci_i2c";
+ };
+
+ config {
+ pins = "gpio17","gpio18";
+ bias-pull-down; /* PULL DOWN */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cci1_active: cci1_active {
+ mux {
+ /* CLK, DATA */
+ pins = "gpio19","gpio20";
+ function = "cci_i2c";
+ };
+
+ config {
+ pins = "gpio19","gpio20";
+ bias-pull-up; /* PULL UP*/
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cci1_suspend: cci1_suspend {
+ mux {
+ /* CLK, DATA */
+ pins = "gpio19","gpio20";
+ function = "cci_i2c";
+ };
+
+ config {
+ pins = "gpio19","gpio20";
+ bias-pull-down; /* PULL DOWN */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_mclk0_active: cam_sensor_mclk0_active {
+ /* MCLK0 */
+ mux {
+ pins = "gpio13";
+ function = "cam_mclk";
+ };
+
+ config {
+ pins = "gpio13";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_mclk0_suspend: cam_sensor_mclk0_suspend {
+ /* MCLK0 */
+ mux {
+ pins = "gpio13";
+ function = "cam_mclk";
+ };
+
+ config {
+ pins = "gpio13";
+ bias-pull-down; /* PULL DOWN */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_rear_active: cam_sensor_rear_active {
+ /* RESET, AVDD LDO */
+ mux {
+ pins = "gpio80","gpio79";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio80","gpio79";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_rear_suspend: cam_sensor_rear_suspend {
+ /* RESET, AVDD LDO */
+ mux {
+ pins = "gpio80","gpio79";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio80","gpio79";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_mclk1_active: cam_sensor_mclk1_active {
+ /* MCLK1 */
+ mux {
+ pins = "gpio14";
+ function = "cam_mclk";
+ };
+
+ config {
+ pins = "gpio14";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_mclk1_suspend: cam_sensor_mclk1_suspend {
+ /* MCLK1 */
+ mux {
+ pins = "gpio14";
+ function = "cam_mclk";
+ };
+
+ config {
+ pins = "gpio14";
+ bias-pull-down; /* PULL DOWN */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_front_active: cam_sensor_front_active {
+ /* RESET AVDD_LDO*/
+ mux {
+ pins = "gpio28", "gpio8";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio28", "gpio8";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_front_suspend: cam_sensor_front_suspend {
+ /* RESET */
+ mux {
+ pins = "gpio28";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio28";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_mclk2_active: cam_sensor_mclk2_active {
+ /* MCLK1 */
+ mux {
+ /* CLK, DATA */
+ pins = "gpio15";
+ function = "cam_mclk";
+ };
+
+ config {
+ pins = "gpio15";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_mclk2_suspend: cam_sensor_mclk2_suspend {
+ /* MCLK1 */
+ mux {
+ /* CLK, DATA */
+ pins = "gpio15";
+ function = "cam_mclk";
+ };
+
+ config {
+ pins = "gpio15";
+ bias-pull-down; /* PULL DOWN */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_rear2_active: cam_sensor_rear2_active {
+ /* RESET, STANDBY */
+ mux {
+ pins = "gpio9","gpio8";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio9","gpio8";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_rear2_suspend: cam_sensor_rear2_suspend {
+ /* RESET, STANDBY */
+ mux {
+ pins = "gpio9","gpio8";
+ function = "gpio";
+ };
+ config {
+ pins = "gpio9","gpio8";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
};
};
@@ -2328,6 +2553,24 @@
power-source = <0>;
};
};
+
+ camera_dvdd_en {
+ camera_dvdd_en_default: camera_dvdd_en_default {
+ pins = "gpio9";
+ function = "normal";
+ power-source = <0>;
+ output-low;
+ };
+ };
+
+ camera_rear_dvdd_en {
+ camera_rear_dvdd_en_default: camera_rear_dvdd_en_default {
+ pins = "gpio12";
+ function = "normal";
+ power-source = <0>;
+ output-low;
+ };
+ };
};
&pmi8998_gpios {