ab8500-bm: Add support for the new ab8540 platform
Provide AB8540 platform specific information required to run the
Battery Management subsystem on AB8540 based devices. For this to
happen we see the introduction of separate platform specific data
structures and a means in which to process them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
diff --git a/drivers/power/ab8500_btemp.c b/drivers/power/ab8500_btemp.c
index 91ad3ed..7336dcf 100644
--- a/drivers/power/ab8500_btemp.c
+++ b/drivers/power/ab8500_btemp.c
@@ -42,6 +42,9 @@
#define BTEMP_BATCTRL_CURR_SRC_16UA 16
#define BTEMP_BATCTRL_CURR_SRC_18UA 18
+#define BTEMP_BATCTRL_CURR_SRC_60UA 60
+#define BTEMP_BATCTRL_CURR_SRC_120UA 120
+
#define to_ab8500_btemp_device_info(x) container_of((x), \
struct ab8500_btemp, btemp_psy);
@@ -216,7 +219,12 @@
/* Only do this for batteries with internal NTC */
if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL && enable) {
- if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
+ if (is_ab8540(di->parent)) {
+ if (di->curr_source == BTEMP_BATCTRL_CURR_SRC_60UA)
+ curr = BAT_CTRL_60U_ENA;
+ else
+ curr = BAT_CTRL_120U_ENA;
+ } else if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
if (di->curr_source == BTEMP_BATCTRL_CURR_SRC_16UA)
curr = BAT_CTRL_16U_ENA;
else
@@ -257,7 +265,14 @@
} else if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL && !enable) {
dev_dbg(di->dev, "Disable BATCTRL curr source\n");
- if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
+ if (is_ab8540(di->parent)) {
+ /* Write 0 to the curr bits */
+ ret = abx500_mask_and_set_register_interruptible(
+ di->dev,
+ AB8500_CHARGER, AB8500_BAT_CTRL_CURRENT_SOURCE,
+ BAT_CTRL_60U_ENA | BAT_CTRL_120U_ENA,
+ ~(BAT_CTRL_60U_ENA | BAT_CTRL_120U_ENA));
+ } else if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
/* Write 0 to the curr bits */
ret = abx500_mask_and_set_register_interruptible(
di->dev,
@@ -314,7 +329,13 @@
* if we got an error above
*/
disable_curr_source:
- if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
+ if (is_ab8540(di->parent)) {
+ /* Write 0 to the curr bits */
+ ret = abx500_mask_and_set_register_interruptible(di->dev,
+ AB8500_CHARGER, AB8500_BAT_CTRL_CURRENT_SOURCE,
+ BAT_CTRL_60U_ENA | BAT_CTRL_120U_ENA,
+ ~(BAT_CTRL_60U_ENA | BAT_CTRL_120U_ENA));
+ } else if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
/* Write 0 to the curr bits */
ret = abx500_mask_and_set_register_interruptible(di->dev,
AB8500_CHARGER, AB8500_BAT_CTRL_CURRENT_SOURCE,
@@ -541,7 +562,9 @@
{
int res;
u8 i;
- if (is_ab9540(di->parent) || is_ab8505(di->parent))
+ if (is_ab8540(di->parent))
+ di->curr_source = BTEMP_BATCTRL_CURR_SRC_60UA;
+ else if (is_ab9540(di->parent) || is_ab8505(di->parent))
di->curr_source = BTEMP_BATCTRL_CURR_SRC_16UA;
else
di->curr_source = BTEMP_BATCTRL_CURR_SRC_7UA;
@@ -582,9 +605,14 @@
* detected type is Type 1, else we use the 7uA source
*/
if (di->bm->adc_therm == ABx500_ADC_THERM_BATCTRL &&
- di->bm->batt_id == 1) {
- if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
- dev_dbg(di->dev, "Set BATCTRL current source to 16uA\n");
+ di->bm->batt_id == 1) {
+ if (is_ab8540(di->parent)) {
+ dev_dbg(di->dev,
+ "Set BATCTRL current source to 60uA\n");
+ di->curr_source = BTEMP_BATCTRL_CURR_SRC_60UA;
+ } else if (is_ab9540(di->parent) || is_ab8505(di->parent)) {
+ dev_dbg(di->dev,
+ "Set BATCTRL current source to 16uA\n");
di->curr_source = BTEMP_BATCTRL_CURR_SRC_16UA;
} else {
dev_dbg(di->dev, "Set BATCTRL current source to 20uA\n");