include/asm-arm/arch-clps711x/hardware.h - kernel/msm-4.9 - Gitiles

 /*
  *  linux/include/asm-arm/arch-clps711x/hardware.h
  *
  *  This file contains the hardware definitions of the Prospector P720T.
  *
  *  Copyright (C) 2000 Deep Blue Solutions Ltd.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
  * the Free Software Foundation; either version 2 of the License, or
  * (at your option) any later version.
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  */
 #ifndef __ASM_ARCH_HARDWARE_H
 #define __ASM_ARCH_HARDWARE_H

 #include <linux/config.h>

 #define CLPS7111_VIRT_BASE	0xff000000
 #define CLPS7111_BASE		CLPS7111_VIRT_BASE

 /*
  * The physical addresses that the external chip select signals map to is
  * dependent on the setting of the nMEDCHG signal on EP7211 and EP7212
  * processors.  CONFIG_EP72XX_BOOT_ROM is only available if these
  * processors are in use.
  */
 #ifndef CONFIG_EP72XX_ROM_BOOT
 #define CS0_PHYS_BASE		(0x00000000)
 #define CS1_PHYS_BASE		(0x10000000)
 #define CS2_PHYS_BASE		(0x20000000)
 #define CS3_PHYS_BASE		(0x30000000)
 #define CS4_PHYS_BASE		(0x40000000)
 #define CS5_PHYS_BASE		(0x50000000)
 #define CS6_PHYS_BASE		(0x60000000)
 #define CS7_PHYS_BASE		(0x70000000)
 #else
 #define CS0_PHYS_BASE		(0x70000000)
 #define CS1_PHYS_BASE		(0x60000000)
 #define CS2_PHYS_BASE		(0x50000000)
 #define CS3_PHYS_BASE		(0x40000000)
 #define CS4_PHYS_BASE		(0x30000000)
 #define CS5_PHYS_BASE		(0x20000000)
 #define CS6_PHYS_BASE		(0x10000000)
 #define CS7_PHYS_BASE		(0x00000000)
 #endif

 #if defined (CONFIG_ARCH_EP7211)

 #define EP7211_VIRT_BASE	CLPS7111_VIRT_BASE
 #define EP7211_BASE		CLPS7111_VIRT_BASE
 #include <asm/hardware/ep7211.h>

 #elif defined (CONFIG_ARCH_EP7212)

 #define EP7212_VIRT_BASE	CLPS7111_VIRT_BASE
 #define EP7212_BASE		CLPS7111_VIRT_BASE
 #include <asm/hardware/ep7212.h>

 #endif

 #define SYSPLD_VIRT_BASE	0xfe000000
 #define SYSPLD_BASE		SYSPLD_VIRT_BASE

 #ifndef __ASSEMBLER__

 #define PCIO_BASE		IO_BASE

 #endif


 #if  defined (CONFIG_ARCH_AUTCPU12)

 #define  CS89712_VIRT_BASE	CLPS7111_VIRT_BASE
 #define  CS89712_BASE		CLPS7111_VIRT_BASE

 #include <asm/hardware/clps7111.h>
 #include <asm/hardware/ep7212.h>
 #include <asm/hardware/cs89712.h>

 #endif


 #if defined (CONFIG_ARCH_CDB89712)

 #include <asm/hardware/clps7111.h>
 #include <asm/hardware/ep7212.h>
 #include <asm/hardware/cs89712.h>

 /* dynamic ioremap() areas */
 #define FLASH_START      0x00000000
 #define FLASH_SIZE       0x800000
 #define FLASH_WIDTH      4

 #define SRAM_START       0x60000000
 #define SRAM_SIZE        0xc000
 #define SRAM_WIDTH       4

 #define BOOTROM_START    0x70000000
 #define BOOTROM_SIZE     0x80
 #define BOOTROM_WIDTH    4


 /* static cdb89712_map_io() areas */
 #define REGISTER_START   0x80000000
 #define REGISTER_SIZE    0x4000
 #define REGISTER_BASE    0xff000000

 #define ETHER_START      0x20000000
 #define ETHER_SIZE       0x1000
 #define ETHER_BASE       0xfe000000

 #endif


 #if defined (CONFIG_ARCH_EDB7211)

 /*
  * The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3)
  * and repeat across it. This is the mapping for it.
  *
  * In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This
  * was cause for much consternation and headscratching. This should probably
  * be made a compile/run time kernel option.
  */
 #define EP7211_PHYS_EXTKBD		CS3_PHYS_BASE	/* physical */

 #define EP7211_VIRT_EXTKBD		(0xfd000000)	/* virtual */


 /*
  * The CS8900A ethernet chip has its I/O registers wired to chip select 2
  * (nCS2). This is the mapping for it.
  *
  * In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This
  * was cause for much consternation and headscratching. This should probably
  * be made a compile/run time kernel option.
  */
 #define EP7211_PHYS_CS8900A		CS2_PHYS_BASE	/* physical */

 #define EP7211_VIRT_CS8900A		(0xfc000000)	/* virtual */


 /*
  * The two flash banks are wired to chip selects 0 and 1. This is the mapping
  * for them.
  *
  * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
  * in jumpered boot mode.
  */
 #define EP7211_PHYS_FLASH1		CS0_PHYS_BASE	/* physical */
 #define EP7211_PHYS_FLASH2		CS1_PHYS_BASE	/* physical */

 #define EP7211_VIRT_FLASH1		(0xfa000000)	/* virtual */
 #define EP7211_VIRT_FLASH2		(0xfb000000)	/* virtual */

 #endif /* CONFIG_ARCH_EDB7211 */


 /*
  * Relevant bits in port D, which controls power to the various parts of
  * the LCD on the EDB7211.
  */
 #define EDB_PD1_LCD_DC_DC_EN	(1<<1)
 #define EDB_PD2_LCDEN		(1<<2)
 #define EDB_PD3_LCDBL		(1<<3)


 #if defined (CONFIG_ARCH_CEIVA)

 #define  CEIVA_VIRT_BASE	CLPS7111_VIRT_BASE
 #define  CEIVA_BASE		CLPS7111_VIRT_BASE

 #include <asm/hardware/clps7111.h>
 #include <asm/hardware/ep7212.h>


 /*
  * The two flash banks are wired to chip selects 0 and 1. This is the mapping
  * for them.
  *
  * nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
  * in jumpered boot mode.
  */
 #define CEIVA_PHYS_FLASH1	CS0_PHYS_BASE	/* physical */
 #define CEIVA_PHYS_FLASH2	CS1_PHYS_BASE	/* physical */

 #define CEIVA_VIRT_FLASH1	(0xfa000000)	/* virtual */
 #define CEIVA_VIRT_FLASH2	(0xfb000000)	/* virtual */

 #define CEIVA_FLASH_SIZE        0x100000
 #define CEIVA_FLASH_WIDTH       2

 #define SRAM_START       0x60000000
 #define SRAM_SIZE        0xc000
 #define SRAM_WIDTH       4

 #define BOOTROM_START    0x70000000
 #define BOOTROM_SIZE     0x80
 #define BOOTROM_WIDTH    4

 /*
  * SED1355 LCD controller
  */
 #define CEIVA_PHYS_SED1355	CS2_PHYS_BASE
 #define CEIVA_VIRT_SED1355	(0xfc000000)

 /*
  * Relevant bits in port D, which controls power to the various parts of
  * the LCD on the Ceiva Photo Max, and reset to the LCD controller.
  */

 // Reset line to SED1355 (must be high to operate)
 #define CEIVA_PD1_LCDRST	(1<<1)
 // LCD panel enable (set to one, to enable LCD)
 #define CEIVA_PD4_LCDEN		(1<<4)
 // Backlight (set to one, to turn on backlight
 #define CEIVA_PD5_LCDBL		(1<<5)

 /*
  * Relevant bits in port B, which report the status of the buttons.
  */

 // White button
 #define CEIVA_PB4_WHT_BTN	(1<<4)
 // Black button
 #define CEIVA_PB0_BLK_BTN	(1<<0)
 #endif // #if defined (CONFIG_ARCH_CEIVA)

 #if defined (CONFIG_MACH_MP1000)
 /* NOR FLASH */
 #define MP1000_NIO_BASE		0xf9000000	/* virtual */
 #define MP1000_NIO_START	CS0_PHYS_BASE	/* physical */
 #define MP1000_NIO_SIZE		0x00400000

 /* DSP Interface */
 #define MP1000_DSP_BASE		0xfa000000	/* virtual */
 #define MP1000_DSP_START	CS1_PHYS_BASE	/* physical */
 #define MP1000_DSP_SIZE		0x00100000

 /* LCD, DAA/DSP, RTC, DAA RW Reg all in CS2 */
 #define MP1000_LIO_BASE		0xfb000000	/* virtual */
 #define MP1000_LIO_START	CS2_PHYS_BASE	/* physical */
 #define MP1000_LIO_SIZE		0x00100000

 /* NAND FLASH */
 #define MP1000_FIO_BASE		0xfc000000	/* virtual */
 #define MP1000_FIO_START	CS3_PHYS_BASE	/* physical */
 #define MP1000_FIO_SIZE		0x00800000

 /* Ethernet */
 #define MP1000_EIO_BASE		0xfd000000	/* virtual 	*/
 #define MP1000_EIO_START	CS4_PHYS_BASE	/* physical 	*/
 #define MP1000_EIO_SIZE		0x00100000

 #define	MP1000_LCD_OFFSET	0x00000000	/* LCD offset in CS2 */
 #define	MP1000_DDD_OFFSET	0x00001000	/* DAA/DAI/DSP sft reset offst*/
 #define	MP1000_RTC_OFFSET	0x00002000	/* RTC offset in CS2 */
 #define	MP1000_DAA_OFFSET	0x00003000	/* DAA RW reg offset in CS2 */

 /* IDE */
 #define MP1000_IDE_BASE		0xfe000000      /* virtual */
 #define MP1000_IDE_START	CS5_PHYS_BASE      /* physical */
 #define MP1000_IDE_SIZE		0x00100000      /* actually it's only 0x1000 */

 #define IRQ_HARDDISK IRQ_EINT2

 /*
  * IDE registers definition
  */

 #define IDE_CONTROL_BASE		(MP1000_IDE_BASE + 0x1000)
 #define IDE_BASE_OFF			(MP1000_IDE_BASE)

 #define IDE_WRITE_DEVICE_DATA		(IDE_BASE_OFF + 0x0)
 #define IDE_FEATURES_REGISTER		(IDE_BASE_OFF + 0x2)
 #define IDE_SECTOR_COUNT_REGISTER	(IDE_BASE_OFF + 0x4)
 #define IDE_SECTOR_NUMBER_REGISTER	(IDE_BASE_OFF + 0x6)
 #define IDE_CYLINDER_LOW_REGISTER	(IDE_BASE_OFF + 0x8)
 #define IDE_CYLINDER_HIGH_REGISTER	(IDE_BASE_OFF + 0xa)
 #define IDE_DEVICE_HEAD_REGISTER	(IDE_BASE_OFF + 0xc)
 #define IDE_COMMAND_DATA_REGISTER	(IDE_BASE_OFF + 0xe)
 #define IDE_DEVICE_CONTROL_REGISTER	(IDE_CONTROL_BASE + 0xc)

 #define IDE_IRQ                      IRQ_EINT2


 #define RTC_PORT(x)	(MP1000_LIO_BASE+0x2000 + (x*2))
 #define RTC_ALWAYS_BCD	0

 /*
 // Definitions of the bit fields in the HwPortA register for the
 // MP1000 board.
 */
 #define HwPortAKeyboardRow1                     0x00000001
 #define HwPortAKeyboardRow2                     0x00000002
 #define HwPortAKeyboardRow3                     0x00000004
 #define HwPortAKeyboardRow4                     0x00000008
 #define HwPortAKeyboardRow5                     0x00000010
 #define HwPortAKeyboardRow6                     0x00000020
 #define HwPortALCDEnable                        0x00000040
 #define HwPortAOffhook	                        0x00000080

 /*
 // Definitions of the bit fields in the HwPortB register for the
 // MP1000 board.
 */
 #define HwPortBL3Mode                           0x00000001
 #define HwPortBL3Clk                            0x00000002
 #define HwPortBSClk                             0x00000001
 #define HwPortBSData                            0x00000002
 #define HwPortBL3Data                           0x00000004
 #define HwPortBMute                             0x00000008
 #define HwPortBQD0                              0x00000010
 #define HwPortBQD1                              0x00000020
 #define HwPortBQD2                              0x00000040
 #define HwPortBQD3                              0x00000080

 /*
 // Definitions of the bit fields in the HwPortD register for the
 // MP1000 board.
 */
 #define HwPortDLED1                             0x00000001
 #define HwPortDLED2                             0x00000002
 #define HwPortDLED3                             0x00000004
 #define HwPortDLED4                             0x00000008
 #define HwPortDLED5                             0x00000010
 #define HwPortDEECS                             0x00000020
 #define HwPortBRTS                              0x00000040
 #define HwPortBRI                               0x00000080


 /*
 // Definitions of the bit fields in the HwPortE register for the
 // MP1000 board.
 */

 #define HwPortECLE                              0x00000001
 #define HwPortESepromDOut                       0x00000001
 #define HwPortEALE                              0x00000002
 #define HwPortESepromDIn                        0x00000002
 #define HwPortENANDCS                           0x00000004
 #define HwPortESepromCLK                        0x00000004

 #endif // #if defined (CONFIG_MACH_MP1000)

 #endif
	/*
	* linux/include/asm-arm/arch-clps711x/hardware.h
	*
	* This file contains the hardware definitions of the Prospector P720T.
	*
	* Copyright (C) 2000 Deep Blue Solutions Ltd.
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License as published by
	* the Free Software Foundation; either version 2 of the License, or
	* (at your option) any later version.
	*
	* This program is distributed in the hope that it will be useful,
	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	* GNU General Public License for more details.
	*
	* You should have received a copy of the GNU General Public License
	* along with this program; if not, write to the Free Software
	* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
	*/
	#ifndef __ASM_ARCH_HARDWARE_H
	#define __ASM_ARCH_HARDWARE_H

	#include <linux/config.h>

	#define CLPS7111_VIRT_BASE 0xff000000
	#define CLPS7111_BASE CLPS7111_VIRT_BASE

	/*
	* The physical addresses that the external chip select signals map to is
	* dependent on the setting of the nMEDCHG signal on EP7211 and EP7212
	* processors. CONFIG_EP72XX_BOOT_ROM is only available if these
	* processors are in use.
	*/
	#ifndef CONFIG_EP72XX_ROM_BOOT
	#define CS0_PHYS_BASE (0x00000000)
	#define CS1_PHYS_BASE (0x10000000)
	#define CS2_PHYS_BASE (0x20000000)
	#define CS3_PHYS_BASE (0x30000000)
	#define CS4_PHYS_BASE (0x40000000)
	#define CS5_PHYS_BASE (0x50000000)
	#define CS6_PHYS_BASE (0x60000000)
	#define CS7_PHYS_BASE (0x70000000)
	#else
	#define CS0_PHYS_BASE (0x70000000)
	#define CS1_PHYS_BASE (0x60000000)
	#define CS2_PHYS_BASE (0x50000000)
	#define CS3_PHYS_BASE (0x40000000)
	#define CS4_PHYS_BASE (0x30000000)
	#define CS5_PHYS_BASE (0x20000000)
	#define CS6_PHYS_BASE (0x10000000)
	#define CS7_PHYS_BASE (0x00000000)
	#endif

	#if defined (CONFIG_ARCH_EP7211)

	#define EP7211_VIRT_BASE CLPS7111_VIRT_BASE
	#define EP7211_BASE CLPS7111_VIRT_BASE
	#include <asm/hardware/ep7211.h>

	#elif defined (CONFIG_ARCH_EP7212)

	#define EP7212_VIRT_BASE CLPS7111_VIRT_BASE
	#define EP7212_BASE CLPS7111_VIRT_BASE
	#include <asm/hardware/ep7212.h>

	#endif

	#define SYSPLD_VIRT_BASE 0xfe000000
	#define SYSPLD_BASE SYSPLD_VIRT_BASE

	#ifndef __ASSEMBLER__

	#define PCIO_BASE IO_BASE

	#endif


	#if defined (CONFIG_ARCH_AUTCPU12)

	#define CS89712_VIRT_BASE CLPS7111_VIRT_BASE
	#define CS89712_BASE CLPS7111_VIRT_BASE

	#include <asm/hardware/clps7111.h>
	#include <asm/hardware/ep7212.h>
	#include <asm/hardware/cs89712.h>

	#endif


	#if defined (CONFIG_ARCH_CDB89712)

	#include <asm/hardware/clps7111.h>
	#include <asm/hardware/ep7212.h>
	#include <asm/hardware/cs89712.h>

	/* dynamic ioremap() areas */
	#define FLASH_START 0x00000000
	#define FLASH_SIZE 0x800000
	#define FLASH_WIDTH 4

	#define SRAM_START 0x60000000
	#define SRAM_SIZE 0xc000
	#define SRAM_WIDTH 4

	#define BOOTROM_START 0x70000000
	#define BOOTROM_SIZE 0x80
	#define BOOTROM_WIDTH 4


	/* static cdb89712_map_io() areas */
	#define REGISTER_START 0x80000000
	#define REGISTER_SIZE 0x4000
	#define REGISTER_BASE 0xff000000

	#define ETHER_START 0x20000000
	#define ETHER_SIZE 0x1000
	#define ETHER_BASE 0xfe000000

	#endif


	#if defined (CONFIG_ARCH_EDB7211)

	/*
	* The extra 8 lines of the keyboard matrix are wired to chip select 3 (nCS3)
	* and repeat across it. This is the mapping for it.
	*
	* In jumpered boot mode, nCS3 is mapped to 0x4000000, not 0x3000000. This
	* was cause for much consternation and headscratching. This should probably
	* be made a compile/run time kernel option.
	*/
	#define EP7211_PHYS_EXTKBD CS3_PHYS_BASE /* physical */

	#define EP7211_VIRT_EXTKBD (0xfd000000) /* virtual */


	/*
	* The CS8900A ethernet chip has its I/O registers wired to chip select 2
	* (nCS2). This is the mapping for it.
	*
	* In jumpered boot mode, nCS2 is mapped to 0x5000000, not 0x2000000. This
	* was cause for much consternation and headscratching. This should probably
	* be made a compile/run time kernel option.
	*/
	#define EP7211_PHYS_CS8900A CS2_PHYS_BASE /* physical */

	#define EP7211_VIRT_CS8900A (0xfc000000) /* virtual */


	/*
	* The two flash banks are wired to chip selects 0 and 1. This is the mapping
	* for them.
	*
	* nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
	* in jumpered boot mode.
	*/
	#define EP7211_PHYS_FLASH1 CS0_PHYS_BASE /* physical */
	#define EP7211_PHYS_FLASH2 CS1_PHYS_BASE /* physical */

	#define EP7211_VIRT_FLASH1 (0xfa000000) /* virtual */
	#define EP7211_VIRT_FLASH2 (0xfb000000) /* virtual */

	#endif /* CONFIG_ARCH_EDB7211 */


	/*
	* Relevant bits in port D, which controls power to the various parts of
	* the LCD on the EDB7211.
	*/
	#define EDB_PD1_LCD_DC_DC_EN (1<<1)
	#define EDB_PD2_LCDEN (1<<2)
	#define EDB_PD3_LCDBL (1<<3)


	#if defined (CONFIG_ARCH_CEIVA)

	#define CEIVA_VIRT_BASE CLPS7111_VIRT_BASE
	#define CEIVA_BASE CLPS7111_VIRT_BASE

	#include <asm/hardware/clps7111.h>
	#include <asm/hardware/ep7212.h>


	/*
	* The two flash banks are wired to chip selects 0 and 1. This is the mapping
	* for them.
	*
	* nCS0 and nCS1 are at 0x70000000 and 0x60000000, respectively, when running
	* in jumpered boot mode.
	*/
	#define CEIVA_PHYS_FLASH1 CS0_PHYS_BASE /* physical */
	#define CEIVA_PHYS_FLASH2 CS1_PHYS_BASE /* physical */

	#define CEIVA_VIRT_FLASH1 (0xfa000000) /* virtual */
	#define CEIVA_VIRT_FLASH2 (0xfb000000) /* virtual */

	#define CEIVA_FLASH_SIZE 0x100000
	#define CEIVA_FLASH_WIDTH 2

	#define SRAM_START 0x60000000
	#define SRAM_SIZE 0xc000
	#define SRAM_WIDTH 4

	#define BOOTROM_START 0x70000000
	#define BOOTROM_SIZE 0x80
	#define BOOTROM_WIDTH 4

	/*
	* SED1355 LCD controller
	*/
	#define CEIVA_PHYS_SED1355 CS2_PHYS_BASE
	#define CEIVA_VIRT_SED1355 (0xfc000000)

	/*
	* Relevant bits in port D, which controls power to the various parts of
	* the LCD on the Ceiva Photo Max, and reset to the LCD controller.
	*/

	// Reset line to SED1355 (must be high to operate)
	#define CEIVA_PD1_LCDRST (1<<1)
	// LCD panel enable (set to one, to enable LCD)
	#define CEIVA_PD4_LCDEN (1<<4)
	// Backlight (set to one, to turn on backlight
	#define CEIVA_PD5_LCDBL (1<<5)

	/*
	* Relevant bits in port B, which report the status of the buttons.
	*/

	// White button
	#define CEIVA_PB4_WHT_BTN (1<<4)
	// Black button
	#define CEIVA_PB0_BLK_BTN (1<<0)
	#endif // #if defined (CONFIG_ARCH_CEIVA)

	#if defined (CONFIG_MACH_MP1000)
	/* NOR FLASH */
	#define MP1000_NIO_BASE 0xf9000000 /* virtual */
	#define MP1000_NIO_START CS0_PHYS_BASE /* physical */
	#define MP1000_NIO_SIZE 0x00400000

	/* DSP Interface */
	#define MP1000_DSP_BASE 0xfa000000 /* virtual */
	#define MP1000_DSP_START CS1_PHYS_BASE /* physical */
	#define MP1000_DSP_SIZE 0x00100000

	/* LCD, DAA/DSP, RTC, DAA RW Reg all in CS2 */
	#define MP1000_LIO_BASE 0xfb000000 /* virtual */
	#define MP1000_LIO_START CS2_PHYS_BASE /* physical */
	#define MP1000_LIO_SIZE 0x00100000

	/* NAND FLASH */
	#define MP1000_FIO_BASE 0xfc000000 /* virtual */
	#define MP1000_FIO_START CS3_PHYS_BASE /* physical */
	#define MP1000_FIO_SIZE 0x00800000

	/* Ethernet */
	#define MP1000_EIO_BASE 0xfd000000 /* virtual */
	#define MP1000_EIO_START CS4_PHYS_BASE /* physical */
	#define MP1000_EIO_SIZE 0x00100000

	#define MP1000_LCD_OFFSET 0x00000000 /* LCD offset in CS2 */
	#define MP1000_DDD_OFFSET 0x00001000 /* DAA/DAI/DSP sft reset offst*/
	#define MP1000_RTC_OFFSET 0x00002000 /* RTC offset in CS2 */
	#define MP1000_DAA_OFFSET 0x00003000 /* DAA RW reg offset in CS2 */

	/* IDE */
	#define MP1000_IDE_BASE 0xfe000000 /* virtual */
	#define MP1000_IDE_START CS5_PHYS_BASE /* physical */
	#define MP1000_IDE_SIZE 0x00100000 /* actually it's only 0x1000 */

	#define IRQ_HARDDISK IRQ_EINT2

	/*
	* IDE registers definition
	*/

	#define IDE_CONTROL_BASE (MP1000_IDE_BASE + 0x1000)
	#define IDE_BASE_OFF (MP1000_IDE_BASE)

	#define IDE_WRITE_DEVICE_DATA (IDE_BASE_OFF + 0x0)
	#define IDE_FEATURES_REGISTER (IDE_BASE_OFF + 0x2)
	#define IDE_SECTOR_COUNT_REGISTER (IDE_BASE_OFF + 0x4)
	#define IDE_SECTOR_NUMBER_REGISTER (IDE_BASE_OFF + 0x6)
	#define IDE_CYLINDER_LOW_REGISTER (IDE_BASE_OFF + 0x8)
	#define IDE_CYLINDER_HIGH_REGISTER (IDE_BASE_OFF + 0xa)
	#define IDE_DEVICE_HEAD_REGISTER (IDE_BASE_OFF + 0xc)
	#define IDE_COMMAND_DATA_REGISTER (IDE_BASE_OFF + 0xe)
	#define IDE_DEVICE_CONTROL_REGISTER (IDE_CONTROL_BASE + 0xc)

	#define IDE_IRQ IRQ_EINT2


	#define RTC_PORT(x) (MP1000_LIO_BASE+0x2000 + (x*2))
	#define RTC_ALWAYS_BCD 0

	/*
	// Definitions of the bit fields in the HwPortA register for the
	// MP1000 board.
	*/
	#define HwPortAKeyboardRow1 0x00000001
	#define HwPortAKeyboardRow2 0x00000002
	#define HwPortAKeyboardRow3 0x00000004
	#define HwPortAKeyboardRow4 0x00000008
	#define HwPortAKeyboardRow5 0x00000010
	#define HwPortAKeyboardRow6 0x00000020
	#define HwPortALCDEnable 0x00000040
	#define HwPortAOffhook 0x00000080

	/*
	// Definitions of the bit fields in the HwPortB register for the
	// MP1000 board.
	*/
	#define HwPortBL3Mode 0x00000001
	#define HwPortBL3Clk 0x00000002
	#define HwPortBSClk 0x00000001
	#define HwPortBSData 0x00000002
	#define HwPortBL3Data 0x00000004
	#define HwPortBMute 0x00000008
	#define HwPortBQD0 0x00000010
	#define HwPortBQD1 0x00000020
	#define HwPortBQD2 0x00000040
	#define HwPortBQD3 0x00000080

	/*
	// Definitions of the bit fields in the HwPortD register for the
	// MP1000 board.
	*/
	#define HwPortDLED1 0x00000001
	#define HwPortDLED2 0x00000002
	#define HwPortDLED3 0x00000004
	#define HwPortDLED4 0x00000008
	#define HwPortDLED5 0x00000010
	#define HwPortDEECS 0x00000020
	#define HwPortBRTS 0x00000040
	#define HwPortBRI 0x00000080


	/*
	// Definitions of the bit fields in the HwPortE register for the
	// MP1000 board.
	*/

	#define HwPortECLE 0x00000001
	#define HwPortESepromDOut 0x00000001
	#define HwPortEALE 0x00000002
	#define HwPortESepromDIn 0x00000002
	#define HwPortENANDCS 0x00000004
	#define HwPortESepromCLK 0x00000004

	#endif // #if defined (CONFIG_MACH_MP1000)

	#endif