pinctrl: intel: Initialize GPIO properly when used through irqchip
commit f5a26acf0162477af6ee4c11b4fb9cffe5d3e257 upstream.
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.
When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.
Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-and-tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/pinctrl/intel/pinctrl-intel.c b/drivers/pinctrl/intel/pinctrl-intel.c
index b40a074..df63b7d 100644
--- a/drivers/pinctrl/intel/pinctrl-intel.c
+++ b/drivers/pinctrl/intel/pinctrl-intel.c
@@ -368,6 +368,18 @@
writel(value, padcfg0);
}
+static void intel_gpio_set_gpio_mode(void __iomem *padcfg0)
+{
+ u32 value;
+
+ /* Put the pad into GPIO mode */
+ value = readl(padcfg0) & ~PADCFG0_PMODE_MASK;
+ /* Disable SCI/SMI/NMI generation */
+ value &= ~(PADCFG0_GPIROUTIOXAPIC | PADCFG0_GPIROUTSCI);
+ value &= ~(PADCFG0_GPIROUTSMI | PADCFG0_GPIROUTNMI);
+ writel(value, padcfg0);
+}
+
static int intel_gpio_request_enable(struct pinctrl_dev *pctldev,
struct pinctrl_gpio_range *range,
unsigned pin)
@@ -375,7 +387,6 @@
struct intel_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
void __iomem *padcfg0;
unsigned long flags;
- u32 value;
raw_spin_lock_irqsave(&pctrl->lock, flags);
@@ -385,13 +396,7 @@
}
padcfg0 = intel_get_padcfg(pctrl, pin, PADCFG0);
- /* Put the pad into GPIO mode */
- value = readl(padcfg0) & ~PADCFG0_PMODE_MASK;
- /* Disable SCI/SMI/NMI generation */
- value &= ~(PADCFG0_GPIROUTIOXAPIC | PADCFG0_GPIROUTSCI);
- value &= ~(PADCFG0_GPIROUTSMI | PADCFG0_GPIROUTNMI);
- writel(value, padcfg0);
-
+ intel_gpio_set_gpio_mode(padcfg0);
/* Disable TX buffer and enable RX (this will be input) */
__intel_gpio_set_direction(padcfg0, true);
@@ -770,6 +775,8 @@
raw_spin_lock_irqsave(&pctrl->lock, flags);
+ intel_gpio_set_gpio_mode(reg);
+
value = readl(reg);
value &= ~(PADCFG0_RXEVCFG_MASK | PADCFG0_RXINV);