Documentation/devicetree/bindings/powerpc/fsl/fman.txt - kernel/msm-4.9 - Gitiles

 =============================================================================
 Freescale Frame Manager Device Bindings

 CONTENTS
   - FMan Node
   - FMan Port Node
   - FMan MURAM Node
   - FMan dTSEC/XGEC/mEMAC Node
   - FMan IEEE 1588 Node
   - FMan MDIO Node
   - Example

 =============================================================================
 FMan Node

 DESCRIPTION

 Due to the fact that the FMan is an aggregation of sub-engines (ports, MACs,
 etc.) the FMan node will have child nodes for each of them.

 PROPERTIES

 - compatible
 		Usage: required
 		Value type: <stringlist>
 		Definition: Must include "fsl,fman"
 		FMan version can be determined via FM_IP_REV_1 register in the
 		FMan block. The offset is 0xc4 from the beginning of the
 		Frame Processing Manager memory map (0xc3000 from the
 		beginning of the FMan node).

 - cell-index
 		Usage: required
 		Value type: <u32>
 		Definition: Specifies the index of the FMan unit.

 		The cell-index value may be used by the SoC, to identify the
 		FMan unit in the SoC memory map. In the table bellow,
 		there's a description of the cell-index use in each SoC:

 		- P1023:
 		register[bit]			FMan unit	cell-index
 		============================================================
 		DEVDISR[1]			1		0

 		- P2041, P3041, P4080 P5020, P5040:
 		register[bit]			FMan unit	cell-index
 		============================================================
 		DCFG_DEVDISR2[6]		1		0
 		DCFG_DEVDISR2[14]		2		1
 			(Second FM available only in P4080 and P5040)

 		- B4860, T1040, T2080, T4240:
 		register[bit]			FMan unit	cell-index
 		============================================================
 		DCFG_CCSR_DEVDISR2[24]		1		0
 		DCFG_CCSR_DEVDISR2[25]		2		1
 			(Second FM available only in T4240)

 		DEVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in
 		the specific SoC "Device Configuration/Pin Control" Memory
 		Map.

 - reg
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A standard property. Specifies the offset of the
 		following configuration registers:
 		- BMI configuration registers.
 		- QMI configuration registers.
 		- DMA configuration registers.
 		- FPM configuration registers.
 		- FMan controller configuration registers.

 - ranges
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A standard property.

 - clocks
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: phandle for the fman input clock.

 - clock-names
 		usage: required
 		Value type: <stringlist>
 		Definition: "fmanclk" for the fman input clock.

 - interrupts
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A pair of IRQs are specified in this property.
 		The first element is associated with the event interrupts and
 		the second element is associated with the error interrupts.

 - fsl,qman-channel-range
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: Specifies the range of the available dedicated
 		channels in the FMan. The first cell specifies the beginning
 		of the range and the second cell specifies the number of
 		channels.
 		Further information available at:
 		"Work Queue (WQ) Channel Assignments in the QMan" section
 		in DPAA Reference Manual.

 - fsl,qman
 - fsl,bman
 		Usage: required
 		Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt

 =============================================================================
 FMan MURAM Node

 DESCRIPTION

 FMan Internal memory - shared between all the FMan modules.
 It contains data structures that are common and written to or read by
 the modules.
 FMan internal memory is split into the following parts:
 	Packet buffering (Tx/Rx FIFOs)
 	Frames internal context

 PROPERTIES

 - compatible
 		Usage: required
 		Value type: <stringlist>
 		Definition: Must include "fsl,fman-muram"

 - ranges
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A standard property.
 		Specifies the multi-user memory offset and the size within
 		the FMan.

 EXAMPLE

 muram@0 {
 	compatible = "fsl,fman-muram";
 	ranges = <0 0x000000 0x28000>;
 };

 =============================================================================
 FMan Port Node

 DESCRIPTION

 The Frame Manager (FMan) supports several types of hardware ports:
 	Ethernet receiver (RX)
 	Ethernet transmitter (TX)
 	Offline/Host command (O/H)

 PROPERTIES

 - compatible
 		Usage: required
 		Value type: <stringlist>
 		Definition: A standard property.
 		Must include one of the following:
 			- "fsl,fman-v2-port-oh" for FManV2 OH ports
 			- "fsl,fman-v2-port-rx" for FManV2 RX ports
 			- "fsl,fman-v2-port-tx" for FManV2 TX ports
 			- "fsl,fman-v3-port-oh" for FManV3 OH ports
 			- "fsl,fman-v3-port-rx" for FManV3 RX ports
 			- "fsl,fman-v3-port-tx" for FManV3 TX ports

 - cell-index
 		Usage: required
 		Value type: <u32>
 		Definition: Specifies the hardware port id.
 		Each hardware port on the FMan has its own hardware PortID.
 		Super set of all hardware Port IDs available at FMan Reference
 		Manual under "FMan Hardware Ports in Freescale Devices" table.

 		Each hardware port is assigned a 4KB, port-specific page in
 		the FMan hardware port memory region (which is part of the
 		FMan memory map). The first 4 KB in the FMan hardware ports
 		memory region is used for what are called common registers.
 		The subsequent 63 4KB pages are allocated to the hardware
 		ports.
 		The page of a specific port is determined by the cell-index.

 - reg
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: There is one reg region describing the port
 		configuration registers.

 EXAMPLE

 port@a8000 {
 	cell-index = <0x28>;
 	compatible = "fsl,fman-v2-port-tx";
 	reg = <0xa8000 0x1000>;
 };

 port@88000 {
 	cell-index = <0x8>;
 	compatible = "fsl,fman-v2-port-rx";
 	reg = <0x88000 0x1000>;
 };

 port@81000 {
 	cell-index = <0x1>;
 	compatible = "fsl,fman-v2-port-oh";
 	reg = <0x81000 0x1000>;
 };

 =============================================================================
 FMan dTSEC/XGEC/mEMAC Node

 DESCRIPTION

 mEMAC/dTSEC/XGEC are the Ethernet network interfaces

 PROPERTIES

 - compatible
 		Usage: required
 		Value type: <stringlist>
 		Definition: A standard property.
 		Must include one of the following:
 		- "fsl,fman-dtsec" for dTSEC MAC
 		- "fsl,fman-xgec" for XGEC MAC
 		- "fsl,fman-memac for mEMAC MAC

 - cell-index
 		Usage: required
 		Value type: <u32>
 		Definition: Specifies the MAC id.

 		The cell-index value may be used by the FMan or the SoC, to
 		identify the MAC unit in the FMan (or SoC) memory map.
 		In the tables bellow there's a description of the cell-index
 		use, there are two tables, one describes the use of cell-index
 		by the FMan, the second describes the use by the SoC:

 		1. FMan Registers

 		FManV2:
 		register[bit]		MAC		cell-index
 		============================================================
 		FM_EPI[16]		XGEC		8
 		FM_EPI[16+n]		dTSECn		n-1
 		FM_NPI[11+n]		dTSECn		n-1
 			n = 1,..,5

 		FManV3:
 		register[bit]		MAC		cell-index
 		============================================================
 		FM_EPI[16+n]		mEMACn		n-1
 		FM_EPI[25]		mEMAC10		9

 		FM_NPI[11+n]		mEMACn		n-1
 		FM_NPI[10]		mEMAC10		9
 		FM_NPI[11]		mEMAC9		8
 			n = 1,..8

 		FM_EPI and FM_NPI are located in the FMan memory map.

 		2. SoC registers:

 		- P2041, P3041, P4080 P5020, P5040:
 		register[bit]		FMan		MAC		cell
 					Unit				index
 		============================================================
 		DCFG_DEVDISR2[7]	1		XGEC		8
 		DCFG_DEVDISR2[7+n]	1		dTSECn		n-1
 		DCFG_DEVDISR2[15]	2		XGEC		8
 		DCFG_DEVDISR2[15+n]	2		dTSECn		n-1
 			n = 1,..5

 		- T1040, T2080, T4240, B4860:
 		register[bit]			FMan	MAC		cell
 						Unit			index
 		============================================================
 		DCFG_CCSR_DEVDISR2[n-1]		1	mEMACn		n-1
 		DCFG_CCSR_DEVDISR2[11+n]	2	mEMACn		n-1
 			n = 1,..6,9,10

 		EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in
 		the specific SoC "Device Configuration/Pin Control" Memory
 		Map.

 - reg
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A standard property.

 - fsl,fman-ports
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: An array of two phandles - the first references is
 		the FMan RX port and the second is the TX port used by this
 		MAC.

 - ptp-timer
 		Usage required
 		Value type: <phandle>
 		Definition: A phandle for 1EEE1588 timer.

 EXAMPLE

 fman1_tx28: port@a8000 {
 	cell-index = <0x28>;
 	compatible = "fsl,fman-v2-port-tx";
 	reg = <0xa8000 0x1000>;
 };

 fman1_rx8: port@88000 {
 	cell-index = <0x8>;
 	compatible = "fsl,fman-v2-port-rx";
 	reg = <0x88000 0x1000>;
 };

 ptp-timer: ptp_timer@fe000 {
 	compatible = "fsl,fman-ptp-timer";
 	reg = <0xfe000 0x1000>;
 };

 ethernet@e0000 {
 	compatible = "fsl,fman-dtsec";
 	cell-index = <0>;
 	reg = <0xe0000 0x1000>;
 	fsl,fman-ports = <&fman1_rx8 &fman1_tx28>;
 	ptp-timer = <&ptp-timer>;
 };

 ============================================================================
 FMan IEEE 1588 Node

 DESCRIPTION

 The FMan interface to support IEEE 1588


 PROPERTIES

 - compatible
 		Usage: required
 		Value type: <stringlist>
 		Definition: A standard property.
 		Must include "fsl,fman-ptp-timer".

 - reg
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A standard property.

 EXAMPLE

 ptp-timer@fe000 {
 	compatible = "fsl,fman-ptp-timer";
 	reg = <0xfe000 0x1000>;
 };

 =============================================================================
 FMan MDIO Node

 DESCRIPTION

 The MDIO is a bus to which the PHY devices are connected.

 PROPERTIES

 - compatible
 		Usage: required
 		Value type: <stringlist>
 		Definition: A standard property.
 		Must include "fsl,fman-mdio" for 1 Gb/s MDIO from FMan v2.
 		Must include "fsl,fman-xmdio" for 10 Gb/s MDIO from FMan v2.
 		Must include "fsl,fman-memac-mdio" for 1/10 Gb/s MDIO from
 		FMan v3.

 - reg
 		Usage: required
 		Value type: <prop-encoded-array>
 		Definition: A standard property.

 - bus-frequency
 		Usage: optional
 		Value type: <u32>
 		Definition: Specifies the external MDIO bus clock speed to
 		be used, if different from the standard 2.5 MHz.
 		This may be due to the standard speed being unsupported (e.g.
 		due to a hardware problem), or to advertise that all relevant
 		components in the system support a faster speed.

 - interrupts
 		Usage: required for external MDIO
 		Value type: <prop-encoded-array>
 		Definition: Event interrupt of external MDIO controller.

 - fsl,fman-internal-mdio
 		Usage: required for internal MDIO
 		Value type: boolean
 		Definition: Fman has internal MDIO for internal PCS(Physical
 		Coding Sublayer) PHYs and external MDIO for external PHYs.
 		The settings and programming routines for internal/external
 		MDIO are different. Must be included for internal MDIO.

 EXAMPLE

 Example for FMan v2 external MDIO:

 mdio@f1000 {
 	compatible = "fsl,fman-xmdio";
 	reg = <0xf1000 0x1000>;
 	interrupts = <101 2 0 0>;
 };

 Example for FMan v3 internal MDIO:

 mdio@f1000 {
 	compatible = "fsl,fman-memac-mdio";
 	reg = <0xf1000 0x1000>;
 	fsl,fman-internal-mdio;
 };

 =============================================================================
 Example

 fman@400000 {
 	#address-cells = <1>;
 	#size-cells = <1>;
 	cell-index = <1>;
 	compatible = "fsl,fman"
 	ranges = <0 0x400000 0x100000>;
 	reg = <0x400000 0x100000>;
 	clocks = <&fman_clk>;
 	clock-names = "fmanclk";
 	interrupts = <
 		96 2 0 0
 		16 2 1 1>;
 	fsl,qman-channel-range = <0x40 0xc>;

 	muram@0 {
 		compatible = "fsl,fman-muram";
 		reg = <0x0 0x28000>;
 	};

 	port@81000 {
 		cell-index = <1>;
 		compatible = "fsl,fman-v2-port-oh";
 		reg = <0x81000 0x1000>;
 	};

 	port@82000 {
 		cell-index = <2>;
 		compatible = "fsl,fman-v2-port-oh";
 		reg = <0x82000 0x1000>;
 	};

 	port@83000 {
 		cell-index = <3>;
 		compatible = "fsl,fman-v2-port-oh";
 		reg = <0x83000 0x1000>;
 	};

 	port@84000 {
 		cell-index = <4>;
 		compatible = "fsl,fman-v2-port-oh";
 		reg = <0x84000 0x1000>;
 	};

 	port@85000 {
 		cell-index = <5>;
 		compatible = "fsl,fman-v2-port-oh";
 		reg = <0x85000 0x1000>;
 	};

 	port@86000 {
 		cell-index = <6>;
 		compatible = "fsl,fman-v2-port-oh";
 		reg = <0x86000 0x1000>;
 	};

 	fman1_rx_0x8: port@88000 {
 		cell-index = <0x8>;
 		compatible = "fsl,fman-v2-port-rx";
 		reg = <0x88000 0x1000>;
 	};

 	fman1_rx_0x9: port@89000 {
 		cell-index = <0x9>;
 		compatible = "fsl,fman-v2-port-rx";
 		reg = <0x89000 0x1000>;
 	};

 	fman1_rx_0xa: port@8a000 {
 		cell-index = <0xa>;
 		compatible = "fsl,fman-v2-port-rx";
 		reg = <0x8a000 0x1000>;
 	};

 	fman1_rx_0xb: port@8b000 {
 		cell-index = <0xb>;
 		compatible = "fsl,fman-v2-port-rx";
 		reg = <0x8b000 0x1000>;
 	};

 	fman1_rx_0xc: port@8c000 {
 		cell-index = <0xc>;
 		compatible = "fsl,fman-v2-port-rx";
 		reg = <0x8c000 0x1000>;
 	};

 	fman1_rx_0x10: port@90000 {
 		cell-index = <0x10>;
 		compatible = "fsl,fman-v2-port-rx";
 		reg = <0x90000 0x1000>;
 	};

 	fman1_tx_0x28: port@a8000 {
 		cell-index = <0x28>;
 		compatible = "fsl,fman-v2-port-tx";
 		reg = <0xa8000 0x1000>;
 	};

 	fman1_tx_0x29: port@a9000 {
 		cell-index = <0x29>;
 		compatible = "fsl,fman-v2-port-tx";
 		reg = <0xa9000 0x1000>;
 	};

 	fman1_tx_0x2a: port@aa000 {
 		cell-index = <0x2a>;
 		compatible = "fsl,fman-v2-port-tx";
 		reg = <0xaa000 0x1000>;
 	};

 	fman1_tx_0x2b: port@ab000 {
 		cell-index = <0x2b>;
 		compatible = "fsl,fman-v2-port-tx";
 		reg = <0xab000 0x1000>;
 	};

 	fman1_tx_0x2c: port@ac0000 {
 		cell-index = <0x2c>;
 		compatible = "fsl,fman-v2-port-tx";
 		reg = <0xac000 0x1000>;
 	};

 	fman1_tx_0x30: port@b0000 {
 		cell-index = <0x30>;
 		compatible = "fsl,fman-v2-port-tx";
 		reg = <0xb0000 0x1000>;
 	};

 	ethernet@e0000 {
 		compatible = "fsl,fman-dtsec";
 		cell-index = <0>;
 		reg = <0xe0000 0x1000>;
 		fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>;
 	};

 	ethernet@e2000 {
 		compatible = "fsl,fman-dtsec";
 		cell-index = <1>;
 		reg = <0xe2000 0x1000>;
 		fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>;
 	};

 	ethernet@e4000 {
 		compatible = "fsl,fman-dtsec";
 		cell-index = <2>;
 		reg = <0xe4000 0x1000>;
 		fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>;
 	};

 	ethernet@e6000 {
 		compatible = "fsl,fman-dtsec";
 		cell-index = <3>;
 		reg = <0xe6000 0x1000>;
 		fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>;
 	};

 	ethernet@e8000 {
 		compatible = "fsl,fman-dtsec";
 		cell-index = <4>;
 		reg = <0xf0000 0x1000>;
 		fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>;

 	ethernet@f0000 {
 		cell-index = <8>;
 		compatible = "fsl,fman-xgec";
 		reg = <0xf0000 0x1000>;
 		fsl,fman-ports = <&fman1_rx_0x10 &fman1_tx_0x30>;
 	};

 	ptp-timer@fe000 {
 		compatible = "fsl,fman-ptp-timer";
 		reg = <0xfe000 0x1000>;
 	};

 	mdio@f1000 {
 		compatible = "fsl,fman-xmdio";
 		reg = <0xf1000 0x1000>;
 		interrupts = <101 2 0 0>;
 	};
 };
	=============================================================================
	Freescale Frame Manager Device Bindings

	CONTENTS
	- FMan Node
	- FMan Port Node
	- FMan MURAM Node
	- FMan dTSEC/XGEC/mEMAC Node
	- FMan IEEE 1588 Node
	- FMan MDIO Node
	- Example

	=============================================================================
	FMan Node

	DESCRIPTION

	Due to the fact that the FMan is an aggregation of sub-engines (ports, MACs,
	etc.) the FMan node will have child nodes for each of them.

	PROPERTIES

	- compatible
	Usage: required
	Value type: <stringlist>
	Definition: Must include "fsl,fman"
	FMan version can be determined via FM_IP_REV_1 register in the
	FMan block. The offset is 0xc4 from the beginning of the
	Frame Processing Manager memory map (0xc3000 from the
	beginning of the FMan node).

	- cell-index
	Usage: required
	Value type: <u32>
	Definition: Specifies the index of the FMan unit.

	The cell-index value may be used by the SoC, to identify the
	FMan unit in the SoC memory map. In the table bellow,
	there's a description of the cell-index use in each SoC:

	- P1023:
	register[bit] FMan unit cell-index
	============================================================
	DEVDISR[1] 1 0

	- P2041, P3041, P4080 P5020, P5040:
	register[bit] FMan unit cell-index
	============================================================
	DCFG_DEVDISR2[6] 1 0
	DCFG_DEVDISR2[14] 2 1
	(Second FM available only in P4080 and P5040)

	- B4860, T1040, T2080, T4240:
	register[bit] FMan unit cell-index
	============================================================
	DCFG_CCSR_DEVDISR2[24] 1 0
	DCFG_CCSR_DEVDISR2[25] 2 1
	(Second FM available only in T4240)

	DEVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in
	the specific SoC "Device Configuration/Pin Control" Memory
	Map.

	- reg
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A standard property. Specifies the offset of the
	following configuration registers:
	- BMI configuration registers.
	- QMI configuration registers.
	- DMA configuration registers.
	- FPM configuration registers.
	- FMan controller configuration registers.

	- ranges
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A standard property.

	- clocks
	Usage: required
	Value type: <prop-encoded-array>
	Definition: phandle for the fman input clock.

	- clock-names
	usage: required
	Value type: <stringlist>
	Definition: "fmanclk" for the fman input clock.

	- interrupts
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A pair of IRQs are specified in this property.
	The first element is associated with the event interrupts and
	the second element is associated with the error interrupts.

	- fsl,qman-channel-range
	Usage: required
	Value type: <prop-encoded-array>
	Definition: Specifies the range of the available dedicated
	channels in the FMan. The first cell specifies the beginning
	of the range and the second cell specifies the number of
	channels.
	Further information available at:
	"Work Queue (WQ) Channel Assignments in the QMan" section
	in DPAA Reference Manual.

	- fsl,qman
	- fsl,bman
	Usage: required
	Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt

	=============================================================================
	FMan MURAM Node

	DESCRIPTION

	FMan Internal memory - shared between all the FMan modules.
	It contains data structures that are common and written to or read by
	the modules.
	FMan internal memory is split into the following parts:
	Packet buffering (Tx/Rx FIFOs)
	Frames internal context

	PROPERTIES

	- compatible
	Usage: required
	Value type: <stringlist>
	Definition: Must include "fsl,fman-muram"

	- ranges
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A standard property.
	Specifies the multi-user memory offset and the size within
	the FMan.

	EXAMPLE

	muram@0 {
	compatible = "fsl,fman-muram";
	ranges = <0 0x000000 0x28000>;
	};

	=============================================================================
	FMan Port Node

	DESCRIPTION

	The Frame Manager (FMan) supports several types of hardware ports:
	Ethernet receiver (RX)
	Ethernet transmitter (TX)
	Offline/Host command (O/H)

	PROPERTIES

	- compatible
	Usage: required
	Value type: <stringlist>
	Definition: A standard property.
	Must include one of the following:
	- "fsl,fman-v2-port-oh" for FManV2 OH ports
	- "fsl,fman-v2-port-rx" for FManV2 RX ports
	- "fsl,fman-v2-port-tx" for FManV2 TX ports
	- "fsl,fman-v3-port-oh" for FManV3 OH ports
	- "fsl,fman-v3-port-rx" for FManV3 RX ports
	- "fsl,fman-v3-port-tx" for FManV3 TX ports

	- cell-index
	Usage: required
	Value type: <u32>
	Definition: Specifies the hardware port id.
	Each hardware port on the FMan has its own hardware PortID.
	Super set of all hardware Port IDs available at FMan Reference
	Manual under "FMan Hardware Ports in Freescale Devices" table.

	Each hardware port is assigned a 4KB, port-specific page in
	the FMan hardware port memory region (which is part of the
	FMan memory map). The first 4 KB in the FMan hardware ports
	memory region is used for what are called common registers.
	The subsequent 63 4KB pages are allocated to the hardware
	ports.
	The page of a specific port is determined by the cell-index.

	- reg
	Usage: required
	Value type: <prop-encoded-array>
	Definition: There is one reg region describing the port
	configuration registers.

	EXAMPLE

	port@a8000 {
	cell-index = <0x28>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xa8000 0x1000>;
	};

	port@88000 {
	cell-index = <0x8>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x88000 0x1000>;
	};

	port@81000 {
	cell-index = <0x1>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x81000 0x1000>;
	};

	=============================================================================
	FMan dTSEC/XGEC/mEMAC Node

	DESCRIPTION

	mEMAC/dTSEC/XGEC are the Ethernet network interfaces

	PROPERTIES

	- compatible
	Usage: required
	Value type: <stringlist>
	Definition: A standard property.
	Must include one of the following:
	- "fsl,fman-dtsec" for dTSEC MAC
	- "fsl,fman-xgec" for XGEC MAC
	- "fsl,fman-memac for mEMAC MAC

	- cell-index
	Usage: required
	Value type: <u32>
	Definition: Specifies the MAC id.

	The cell-index value may be used by the FMan or the SoC, to
	identify the MAC unit in the FMan (or SoC) memory map.
	In the tables bellow there's a description of the cell-index
	use, there are two tables, one describes the use of cell-index
	by the FMan, the second describes the use by the SoC:

	1. FMan Registers

	FManV2:
	register[bit] MAC cell-index
	============================================================
	FM_EPI[16] XGEC 8
	FM_EPI[16+n] dTSECn n-1
	FM_NPI[11+n] dTSECn n-1
	n = 1,..,5

	FManV3:
	register[bit] MAC cell-index
	============================================================
	FM_EPI[16+n] mEMACn n-1
	FM_EPI[25] mEMAC10 9

	FM_NPI[11+n] mEMACn n-1
	FM_NPI[10] mEMAC10 9
	FM_NPI[11] mEMAC9 8
	n = 1,..8

	FM_EPI and FM_NPI are located in the FMan memory map.

	2. SoC registers:

	- P2041, P3041, P4080 P5020, P5040:
	register[bit] FMan MAC cell
	Unit index
	============================================================
	DCFG_DEVDISR2[7] 1 XGEC 8
	DCFG_DEVDISR2[7+n] 1 dTSECn n-1
	DCFG_DEVDISR2[15] 2 XGEC 8
	DCFG_DEVDISR2[15+n] 2 dTSECn n-1
	n = 1,..5

	- T1040, T2080, T4240, B4860:
	register[bit] FMan MAC cell
	Unit index
	============================================================
	DCFG_CCSR_DEVDISR2[n-1] 1 mEMACn n-1
	DCFG_CCSR_DEVDISR2[11+n] 2 mEMACn n-1
	n = 1,..6,9,10

	EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in
	the specific SoC "Device Configuration/Pin Control" Memory
	Map.

	- reg
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A standard property.

	- fsl,fman-ports
	Usage: required
	Value type: <prop-encoded-array>
	Definition: An array of two phandles - the first references is
	the FMan RX port and the second is the TX port used by this
	MAC.

	- ptp-timer
	Usage required
	Value type: <phandle>
	Definition: A phandle for 1EEE1588 timer.

	EXAMPLE

	fman1_tx28: port@a8000 {
	cell-index = <0x28>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xa8000 0x1000>;
	};

	fman1_rx8: port@88000 {
	cell-index = <0x8>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x88000 0x1000>;
	};

	ptp-timer: ptp_timer@fe000 {
	compatible = "fsl,fman-ptp-timer";
	reg = <0xfe000 0x1000>;
	};

	ethernet@e0000 {
	compatible = "fsl,fman-dtsec";
	cell-index = <0>;
	reg = <0xe0000 0x1000>;
	fsl,fman-ports = <&fman1_rx8 &fman1_tx28>;
	ptp-timer = <&ptp-timer>;
	};

	============================================================================
	FMan IEEE 1588 Node

	DESCRIPTION

	The FMan interface to support IEEE 1588


	PROPERTIES

	- compatible
	Usage: required
	Value type: <stringlist>
	Definition: A standard property.
	Must include "fsl,fman-ptp-timer".

	- reg
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A standard property.

	EXAMPLE

	ptp-timer@fe000 {
	compatible = "fsl,fman-ptp-timer";
	reg = <0xfe000 0x1000>;
	};

	=============================================================================
	FMan MDIO Node

	DESCRIPTION

	The MDIO is a bus to which the PHY devices are connected.

	PROPERTIES

	- compatible
	Usage: required
	Value type: <stringlist>
	Definition: A standard property.
	Must include "fsl,fman-mdio" for 1 Gb/s MDIO from FMan v2.
	Must include "fsl,fman-xmdio" for 10 Gb/s MDIO from FMan v2.
	Must include "fsl,fman-memac-mdio" for 1/10 Gb/s MDIO from
	FMan v3.

	- reg
	Usage: required
	Value type: <prop-encoded-array>
	Definition: A standard property.

	- bus-frequency
	Usage: optional
	Value type: <u32>
	Definition: Specifies the external MDIO bus clock speed to
	be used, if different from the standard 2.5 MHz.
	This may be due to the standard speed being unsupported (e.g.
	due to a hardware problem), or to advertise that all relevant
	components in the system support a faster speed.

	- interrupts
	Usage: required for external MDIO
	Value type: <prop-encoded-array>
	Definition: Event interrupt of external MDIO controller.

	- fsl,fman-internal-mdio
	Usage: required for internal MDIO
	Value type: boolean
	Definition: Fman has internal MDIO for internal PCS(Physical
	Coding Sublayer) PHYs and external MDIO for external PHYs.
	The settings and programming routines for internal/external
	MDIO are different. Must be included for internal MDIO.

	EXAMPLE

	Example for FMan v2 external MDIO:

	mdio@f1000 {
	compatible = "fsl,fman-xmdio";
	reg = <0xf1000 0x1000>;
	interrupts = <101 2 0 0>;
	};

	Example for FMan v3 internal MDIO:

	mdio@f1000 {
	compatible = "fsl,fman-memac-mdio";
	reg = <0xf1000 0x1000>;
	fsl,fman-internal-mdio;
	};

	=============================================================================
	Example

	fman@400000 {
	#address-cells = <1>;
	#size-cells = <1>;
	cell-index = <1>;
	compatible = "fsl,fman"
	ranges = <0 0x400000 0x100000>;
	reg = <0x400000 0x100000>;
	clocks = <&fman_clk>;
	clock-names = "fmanclk";
	interrupts = <
	96 2 0 0
	16 2 1 1>;
	fsl,qman-channel-range = <0x40 0xc>;

	muram@0 {
	compatible = "fsl,fman-muram";
	reg = <0x0 0x28000>;
	};

	port@81000 {
	cell-index = <1>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x81000 0x1000>;
	};

	port@82000 {
	cell-index = <2>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x82000 0x1000>;
	};

	port@83000 {
	cell-index = <3>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x83000 0x1000>;
	};

	port@84000 {
	cell-index = <4>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x84000 0x1000>;
	};

	port@85000 {
	cell-index = <5>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x85000 0x1000>;
	};

	port@86000 {
	cell-index = <6>;
	compatible = "fsl,fman-v2-port-oh";
	reg = <0x86000 0x1000>;
	};

	fman1_rx_0x8: port@88000 {
	cell-index = <0x8>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x88000 0x1000>;
	};

	fman1_rx_0x9: port@89000 {
	cell-index = <0x9>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x89000 0x1000>;
	};

	fman1_rx_0xa: port@8a000 {
	cell-index = <0xa>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x8a000 0x1000>;
	};

	fman1_rx_0xb: port@8b000 {
	cell-index = <0xb>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x8b000 0x1000>;
	};

	fman1_rx_0xc: port@8c000 {
	cell-index = <0xc>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x8c000 0x1000>;
	};

	fman1_rx_0x10: port@90000 {
	cell-index = <0x10>;
	compatible = "fsl,fman-v2-port-rx";
	reg = <0x90000 0x1000>;
	};

	fman1_tx_0x28: port@a8000 {
	cell-index = <0x28>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xa8000 0x1000>;
	};

	fman1_tx_0x29: port@a9000 {
	cell-index = <0x29>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xa9000 0x1000>;
	};

	fman1_tx_0x2a: port@aa000 {
	cell-index = <0x2a>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xaa000 0x1000>;
	};

	fman1_tx_0x2b: port@ab000 {
	cell-index = <0x2b>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xab000 0x1000>;
	};

	fman1_tx_0x2c: port@ac0000 {
	cell-index = <0x2c>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xac000 0x1000>;
	};

	fman1_tx_0x30: port@b0000 {
	cell-index = <0x30>;
	compatible = "fsl,fman-v2-port-tx";
	reg = <0xb0000 0x1000>;
	};

	ethernet@e0000 {
	compatible = "fsl,fman-dtsec";
	cell-index = <0>;
	reg = <0xe0000 0x1000>;
	fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>;
	};

	ethernet@e2000 {
	compatible = "fsl,fman-dtsec";
	cell-index = <1>;
	reg = <0xe2000 0x1000>;
	fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>;
	};

	ethernet@e4000 {
	compatible = "fsl,fman-dtsec";
	cell-index = <2>;
	reg = <0xe4000 0x1000>;
	fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>;
	};

	ethernet@e6000 {
	compatible = "fsl,fman-dtsec";
	cell-index = <3>;
	reg = <0xe6000 0x1000>;
	fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>;
	};

	ethernet@e8000 {
	compatible = "fsl,fman-dtsec";
	cell-index = <4>;
	reg = <0xf0000 0x1000>;
	fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>;

	ethernet@f0000 {
	cell-index = <8>;
	compatible = "fsl,fman-xgec";
	reg = <0xf0000 0x1000>;
	fsl,fman-ports = <&fman1_rx_0x10 &fman1_tx_0x30>;
	};

	ptp-timer@fe000 {
	compatible = "fsl,fman-ptp-timer";
	reg = <0xfe000 0x1000>;
	};

	mdio@f1000 {
	compatible = "fsl,fman-xmdio";
	reg = <0xf1000 0x1000>;
	interrupts = <101 2 0 0>;
	};
	};