Bluetooth: btmrvl: remove cal-data byte swapping and redundant mem copy
The device tree property can define the cal-data in proper order.
There is no need to swap the bytes in driver.
Also remove the redundant cal-data memory copy after removing the
byte swapping.
Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Hyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
diff --git a/drivers/bluetooth/btmrvl_main.c b/drivers/bluetooth/btmrvl_main.c
index 6441f72..1e0320a 100644
--- a/drivers/bluetooth/btmrvl_main.c
+++ b/drivers/bluetooth/btmrvl_main.c
@@ -415,28 +415,20 @@
}
static int btmrvl_download_cal_data(struct btmrvl_private *priv,
- u8 *config_data)
+ u8 *data, int len)
{
- int i, ret;
- u8 data[BT_CMD_DATA_SIZE];
+ int ret;
data[0] = 0x00;
data[1] = 0x00;
data[2] = 0x00;
- data[3] = BT_CMD_DATA_SIZE - 4;
-
- /* Swap cal-data bytes. Each four bytes are swapped. Considering 4
- * byte SDIO header offset, mapping of input and output bytes will be
- * {3, 2, 1, 0} -> {0+4, 1+4, 2+4, 3+4},
- * {7, 6, 5, 4} -> {4+4, 5+4, 6+4, 7+4} */
- for (i = 4; i < BT_CMD_DATA_SIZE; i++)
- data[i] = config_data[(i / 4) * 8 - 1 - i];
+ data[3] = len;
print_hex_dump_bytes("Calibration data: ",
- DUMP_PREFIX_OFFSET, data, BT_CMD_DATA_SIZE);
+ DUMP_PREFIX_OFFSET, data, BT_CAL_HDR_LEN + len);
ret = btmrvl_send_sync_cmd(priv, BT_CMD_LOAD_CONFIG_DATA, data,
- BT_CMD_DATA_SIZE);
+ BT_CAL_HDR_LEN + len);
if (ret)
BT_ERR("Failed to download caibration data\n");
@@ -446,7 +438,7 @@
static int btmrvl_cal_data_dt(struct btmrvl_private *priv)
{
struct device_node *dt_node;
- u8 cal_data[BT_CAL_DATA_SIZE];
+ u8 cal_data[BT_CAL_HDR_LEN + BT_CAL_DATA_SIZE];
const char name[] = "btmrvl_caldata";
const char property[] = "btmrvl,caldata";
int ret;
@@ -455,13 +447,14 @@
if (!dt_node)
return -ENODEV;
- ret = of_property_read_u8_array(dt_node, property, cal_data,
- sizeof(cal_data));
+ ret = of_property_read_u8_array(dt_node, property,
+ cal_data + BT_CAL_HDR_LEN,
+ BT_CAL_DATA_SIZE);
if (ret)
return ret;
BT_DBG("Use cal data from device tree");
- ret = btmrvl_download_cal_data(priv, cal_data);
+ ret = btmrvl_download_cal_data(priv, cal_data, BT_CAL_DATA_SIZE);
if (ret) {
BT_ERR("Fail to download calibrate data");
return ret;