Staging: et131x: fold the diet config into the other code
No point having a file just for that
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/staging/et131x/et131x_initpci.c b/drivers/staging/et131x/et131x_initpci.c
index c489090..34737d1 100644
--- a/drivers/staging/et131x/et131x_initpci.c
+++ b/drivers/staging/et131x/et131x_initpci.c
@@ -140,6 +140,37 @@
dbg_info_t *et131x_dbginfo = &et131x_info;
#endif /* CONFIG_ET131X_DEBUG */
+/* Defines for Parameter Default/Min/Max vaules */
+#define PARM_SPEED_DUPLEX_MIN 0
+#define PARM_SPEED_DUPLEX_MAX 5
+
+/* Module parameter for disabling NMI
+ * et131x_nmi_disable :
+ * Disable NMI (0-2) [0]
+ * 0 :
+ * 1 :
+ * 2 :
+ */
+static u32 et131x_nmi_disable; /* 0-2 */
+module_param(et131x_nmi_disable, uint, 0);
+MODULE_PARM_DESC(et131x_nmi_disable, "Disable NMI (0-2) [0]");
+
+/* Module parameter for manual speed setting
+ * Set Link speed and dublex manually (0-5) [0]
+ * 1 : 10Mb Half-Duplex
+ * 2 : 10Mb Full-Duplex
+ * 3 : 100Mb Half-Duplex
+ * 4 : 100Mb Full-Duplex
+ * 5 : 1000Mb Full-Duplex
+ * 0 : Auto Speed Auto Duplex // default
+ */
+static u32 et131x_speed_set;
+module_param(et131x_speed_set, uint, 0);
+MODULE_PARM_DESC(et131x_speed_set,
+ "Set Link speed and dublex manually (0-5) [0] \n 1 : 10Mb Half-Duplex \n 2 : 10Mb Full-Duplex \n 3 : 100Mb Half-Duplex \n 4 : 100Mb Full-Duplex \n 5 : 1000Mb Full-Duplex \n 0 : Auto Speed Auto Dublex");
+
+
+
static struct pci_device_id et131x_pci_table[] __devinitdata = {
{ET131X_PCI_VENDOR_ID, ET131X_PCI_DEVICE_ID_GIG, PCI_ANY_ID,
PCI_ANY_ID, 0, 0, 0UL},
@@ -202,6 +233,12 @@
DBG_ENTER(et131x_dbginfo);
DBG_PRINT("%s\n", DRIVER_INFO);
+ if (et131x_speed_set < PARM_SPEED_DUPLEX_MIN ||
+ et131x_speed_set > PARM_SPEED_DUPLEX_MAX) {
+ printk(KERN_WARNING "et131x: invalid speed setting ignored.\n");
+ et131x_speed_set = 0;
+ }
+
result = pci_register_driver(&et131x_driver);
DBG_LEAVE(et131x_dbginfo);
@@ -750,6 +787,55 @@
}
/**
+ * et131x_config_parse
+ * @etdev: pointer to the private adapter struct
+ *
+ * Parses a configuration from some location (module parameters, for example)
+ * into the private adapter struct. This really has no sensible analogy in
+ * Linux as sysfs parameters are dynamic. Several things that were hee could
+ * go into sysfs, but other stuff like speed handling is part of the mii
+ * interfaces/ethtool.
+ */
+void et131x_config_parse(struct et131x_adapter *etdev)
+{
+ static const u8 default_mac[] = { 0x00, 0x05, 0x3d, 0x00, 0x02, 0x00 };
+ static const u8 duplex[] = { 0, 1, 2, 1, 2, 2 };
+ static const u16 speed[] = { 0, 10, 10, 100, 100, 1000 };
+
+ DBG_ENTER(et131x_dbginfo);
+
+ if (et131x_speed_set)
+ DBG_VERBOSE(et131x_dbginfo, "Speed set manually to : %d \n",
+ et131x_speed_set);
+
+ etdev->SpeedDuplex = et131x_speed_set;
+ etdev->RegistryJumboPacket = 1514; /* 1514-9216 */
+
+ etdev->RegistryNMIDisable = et131x_nmi_disable;
+
+ /* Set the MAC address to a default */
+ memcpy(etdev->CurrentAddress, default_mac, ETH_ALEN);
+
+ /* Decode SpeedDuplex
+ *
+ * Set up as if we are auto negotiating always and then change if we
+ * go into force mode
+ *
+ * If we are the 10/100 device, and gigabit is somehow requested then
+ * knock it down to 100 full.
+ */
+ if (etdev->pdev->device == ET131X_PCI_DEVICE_ID_FAST &&
+ etdev->SpeedDuplex == 5)
+ etdev->SpeedDuplex = 4;
+
+ etdev->AiForceSpeed = speed[etdev->SpeedDuplex];
+ etdev->AiForceDpx = duplex[etdev->SpeedDuplex]; /* Auto FDX */
+
+ DBG_LEAVE(et131x_dbginfo);
+}
+
+
+/**
* et131x_pci_setup - Perform device initialization
* @pdev: a pointer to the device's pci_dev structure
* @ent: this device's entry in the pci_device_id table