Merge tag 'xceiv-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into USB-next
Pull USB phy patches from Felipe:
"usb: phy: patches for v3.8 merge window
Not too many patches this time. First two patches are only
cleanups where one of them switches over to module_platform_driver
macro and the second removes inclusion of <mach/iomap.h> and is
part of a bigger set of include cleanups from the Tegra folks.
The only substantial change here is the addition of a driver
for Renesas' R-Car USB Phy controller."
diff --git a/drivers/usb/otg/mv_otg.c b/drivers/usb/otg/mv_otg.c
index 3f124e8..1dd5750 100644
--- a/drivers/usb/otg/mv_otg.c
+++ b/drivers/usb/otg/mv_otg.c
@@ -958,16 +958,4 @@
.resume = mv_otg_resume,
#endif
};
-
-static int __init mv_otg_init(void)
-{
- return platform_driver_register(&mv_otg_driver);
-}
-
-static void __exit mv_otg_exit(void)
-{
- platform_driver_unregister(&mv_otg_driver);
-}
-
-module_init(mv_otg_init);
-module_exit(mv_otg_exit);
+module_platform_driver(mv_otg_driver);
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 63c339b..7eb73c5 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -32,3 +32,15 @@
help
Enable this to support Marvell USB 3.0 phy controller for Marvell
SoC.
+
+config USB_RCAR_PHY
+ tristate "Renesas R-Car USB phy support"
+ depends on USB || USB_GADGET
+ select USB_OTG_UTILS
+ help
+ Say Y here to add support for the Renesas R-Car USB phy driver.
+ This chip is typically used as USB phy for USB host, gadget.
+ This driver supports: R8A7779
+
+ To compile this driver as a module, choose M here: the
+ module will be called rcar-phy.
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index b069f29..1a579a8 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -8,3 +8,4 @@
obj-$(CONFIG_USB_ISP1301) += isp1301.o
obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o
obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o
+obj-$(CONFIG_USB_RCAR_PHY) += rcar-phy.o
diff --git a/drivers/usb/phy/rcar-phy.c b/drivers/usb/phy/rcar-phy.c
new file mode 100644
index 0000000..792f505
--- /dev/null
+++ b/drivers/usb/phy/rcar-phy.c
@@ -0,0 +1,220 @@
+/*
+ * Renesas R-Car USB phy driver
+ *
+ * Copyright (C) 2012 Renesas Solutions Corp.
+ * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/usb/otg.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+
+/* USBH common register */
+#define USBPCTRL0 0x0800
+#define USBPCTRL1 0x0804
+#define USBST 0x0808
+#define USBEH0 0x080C
+#define USBOH0 0x081C
+#define USBCTL0 0x0858
+#define EIIBC1 0x0094
+#define EIIBC2 0x009C
+
+/* USBPCTRL1 */
+#define PHY_RST (1 << 2)
+#define PLL_ENB (1 << 1)
+#define PHY_ENB (1 << 0)
+
+/* USBST */
+#define ST_ACT (1 << 31)
+#define ST_PLL (1 << 30)
+
+struct rcar_usb_phy_priv {
+ struct usb_phy phy;
+ spinlock_t lock;
+
+ void __iomem *reg0;
+ void __iomem *reg1;
+ int counter;
+};
+
+#define usb_phy_to_priv(p) container_of(p, struct rcar_usb_phy_priv, phy)
+
+
+/*
+ * USB initial/install operation.
+ *
+ * This function setup USB phy.
+ * The used value and setting order came from
+ * [USB :: Initial setting] on datasheet.
+ */
+static int rcar_usb_phy_init(struct usb_phy *phy)
+{
+ struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
+ struct device *dev = phy->dev;
+ void __iomem *reg0 = priv->reg0;
+ void __iomem *reg1 = priv->reg1;
+ int i;
+ u32 val;
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->lock, flags);
+ if (priv->counter++ == 0) {
+
+ /*
+ * USB phy start-up
+ */
+
+ /* (1) USB-PHY standby release */
+ iowrite32(PHY_ENB, (reg0 + USBPCTRL1));
+
+ /* (2) start USB-PHY internal PLL */
+ iowrite32(PHY_ENB | PLL_ENB, (reg0 + USBPCTRL1));
+
+ /* (3) USB module status check */
+ for (i = 0; i < 1024; i++) {
+ udelay(10);
+ val = ioread32(reg0 + USBST);
+ if (val == (ST_ACT | ST_PLL))
+ break;
+ }
+
+ if (val != (ST_ACT | ST_PLL)) {
+ dev_err(dev, "USB phy not ready\n");
+ goto phy_init_end;
+ }
+
+ /* (4) USB-PHY reset clear */
+ iowrite32(PHY_ENB | PLL_ENB | PHY_RST, (reg0 + USBPCTRL1));
+
+ /* set platform specific port settings */
+ iowrite32(0x00000000, (reg0 + USBPCTRL0));
+
+ /*
+ * EHCI IP internal buffer setting
+ * EHCI IP internal buffer enable
+ *
+ * These are recommended value of a datasheet
+ * see [USB :: EHCI internal buffer setting]
+ */
+ iowrite32(0x00ff0040, (reg0 + EIIBC1));
+ iowrite32(0x00ff0040, (reg1 + EIIBC1));
+
+ iowrite32(0x00000001, (reg0 + EIIBC2));
+ iowrite32(0x00000001, (reg1 + EIIBC2));
+
+ /*
+ * Bus alignment settings
+ */
+
+ /* (1) EHCI bus alignment (little endian) */
+ iowrite32(0x00000000, (reg0 + USBEH0));
+
+ /* (1) OHCI bus alignment (little endian) */
+ iowrite32(0x00000000, (reg0 + USBOH0));
+ }
+
+phy_init_end:
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return 0;
+}
+
+static void rcar_usb_phy_shutdown(struct usb_phy *phy)
+{
+ struct rcar_usb_phy_priv *priv = usb_phy_to_priv(phy);
+ void __iomem *reg0 = priv->reg0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->lock, flags);
+
+ if (priv->counter-- == 1) { /* last user */
+ iowrite32(0x00000000, (reg0 + USBPCTRL0));
+ iowrite32(0x00000000, (reg0 + USBPCTRL1));
+ }
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+}
+
+static int __devinit rcar_usb_phy_probe(struct platform_device *pdev)
+{
+ struct rcar_usb_phy_priv *priv;
+ struct resource *res0, *res1;
+ struct device *dev = &pdev->dev;
+ void __iomem *reg0, *reg1;
+ int ret;
+
+ res0 = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ res1 = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res0 || !res1) {
+ dev_err(dev, "Not enough platform resources\n");
+ return -EINVAL;
+ }
+
+ /*
+ * CAUTION
+ *
+ * Because this phy address is also mapped under OHCI/EHCI address area,
+ * this driver can't use devm_request_and_ioremap(dev, res) here
+ */
+ reg0 = devm_ioremap_nocache(dev, res0->start, resource_size(res0));
+ reg1 = devm_ioremap_nocache(dev, res1->start, resource_size(res1));
+ if (!reg0 || !reg1) {
+ dev_err(dev, "ioremap error\n");
+ return -ENOMEM;
+ }
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv) {
+ dev_err(dev, "priv data allocation error\n");
+ return -ENOMEM;
+ }
+
+ priv->reg0 = reg0;
+ priv->reg1 = reg1;
+ priv->counter = 0;
+ priv->phy.dev = dev;
+ priv->phy.label = dev_name(dev);
+ priv->phy.init = rcar_usb_phy_init;
+ priv->phy.shutdown = rcar_usb_phy_shutdown;
+ spin_lock_init(&priv->lock);
+
+ ret = usb_add_phy(&priv->phy, USB_PHY_TYPE_USB2);
+ if (ret < 0) {
+ dev_err(dev, "usb phy addition error\n");
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ return ret;
+}
+
+static int __devexit rcar_usb_phy_remove(struct platform_device *pdev)
+{
+ struct rcar_usb_phy_priv *priv = platform_get_drvdata(pdev);
+
+ usb_remove_phy(&priv->phy);
+
+ return 0;
+}
+
+static struct platform_driver rcar_usb_phy_driver = {
+ .driver = {
+ .name = "rcar_usb_phy",
+ },
+ .probe = rcar_usb_phy_probe,
+ .remove = __devexit_p(rcar_usb_phy_remove),
+};
+
+module_platform_driver(rcar_usb_phy_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Renesas R-Car USB phy");
+MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");