staging:rtl8192u Fix typos and comments
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/staging/rtl8192u/r8192U_dm.c b/drivers/staging/rtl8192u/r8192U_dm.c
index 3f79e61..996e658 100644
--- a/drivers/staging/rtl8192u/r8192U_dm.c
+++ b/drivers/staging/rtl8192u/r8192U_dm.c
@@ -1457,7 +1457,7 @@
{
struct r8192_priv *priv = ieee80211_priv(dev);
- // Tx Power tracking by Thermal Meter require Firmware R/W 3-wire. This mechanism
+ // Tx Power tracking by Thermal Meter requires Firmware R/W 3-wire. This mechanism
// can be enabled only when Firmware R/W 3-wire is enabled. Otherwise, frequent r/w
// 3-wire by driver causes RF to go into a wrong state.
if(priv->ieee80211->FwRWRF)
@@ -1520,7 +1520,7 @@
if(!TM_Trigger)
{
- //Attention!! You have to write all 12bits data to RF, or it may cause RF to crash
+ //Attention!! You have to write all 12bits of data to RF, or it may cause RF to crash
//actually write reg0x02 bit1=0, then bit1=1.
//DbgPrint("Trigger ThermalMeter, write RF reg0x2 = 0x4d to 0x4f\n");
rtl8192_phy_SetRFReg(dev, RF90_PATH_A, 0x02, bMask12Bits, 0x4d);
@@ -2161,7 +2161,7 @@
pHalData->UndecoratedSmoothedPWDB, DM_DigTable.RssiLowThresh,
DM_DigTable.RssiHighThresh, DM_DigTable.Dig_State);*/
/* 1. When RSSI decrease, We have to judge if it is smaller than a threshold
- and then execute below step. */
+ and then execute the step below. */
if ((priv->undecorated_smoothed_pwdb <= dm_digtable.rssi_low_thresh))
{
/* 2008/02/05 MH When we execute silent reset, the DIG PHY parameters
@@ -2221,7 +2221,7 @@
}
/* 2. When RSSI increase, We have to judge if it is larger than a threshold
- and then execute below step. */
+ and then execute the step below. */
if ((priv->undecorated_smoothed_pwdb >= dm_digtable.rssi_high_thresh) )
{
u8 reset_flag = 0;
@@ -2329,7 +2329,7 @@
}
/* 3. When RSSI >75% or <70%, it is a high power issue. We have to judge if
- it is larger than a threshold and then execute below step. */
+ it is larger than a threshold and then execute the step below. */
// 2008/02/05 MH SD3-Jerry Modify PD_TH for high power issue.
if (priv->undecorated_smoothed_pwdb >= dm_digtable.rssi_high_power_highthresh)
{
@@ -2842,7 +2842,7 @@
//struct r8192_priv *priv = ieee80211_priv(dev);
// Work around for DTM test, we will not enable HW - radio on/off because r/w
- // page 1 register before extra bus is enabled causing system fails when resuming
+ // page 1 register before extra bus is enabled causing system failures when resuming
// from S4. 20080218, Emily
// Stop to execute workitem to prevent S3/S4 bug.
@@ -3392,7 +3392,7 @@
}
else
{
- // Stop continue count
+ // Stop the continued count
priv->ContiuneDiffCount = 0;
}
@@ -3523,7 +3523,7 @@
RT_TRACE(COMP_HALDM,"%s\n", __FUNCTION__);
// Initial rate record to zero, start to record.
priv->rate_record = 0;
- // Initial continue diff count to zero, start to record.
+ // Initialize continue diff count to zero, start to record.
priv->ContiuneDiffCount = 0;
priv->rateCountDiffRecord = 0;
priv->bswitch_fsync = false;