sound/firewire/dice-interface.h - kernel/msm-4.9 - Gitiles

 #ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED
 #define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED

 /*
  * DICE device interface definitions
  */

 /*
  * Generally, all registers can be read like memory, i.e., with quadlet read or
  * block read transactions with at least quadlet-aligned offset and length.
  * Writes are not allowed except where noted; quadlet-sized registers must be
  * written with a quadlet write transaction.
  *
  * All values are in big endian.  The DICE firmware runs on a little-endian CPU
  * and just byte-swaps _all_ quadlets on the bus, so values without endianness
  * (e.g. strings) get scrambled and must be byte-swapped again by the driver.
  */

 /*
  * Streaming is handled by the "DICE driver" interface.  Its registers are
  * located in this private address space.
  */
 #define DICE_PRIVATE_SPACE		0xffffe0000000uLL

 /*
  * The registers are organized in several sections, which are organized
  * separately to allow them to be extended individually.  Whether a register is
  * supported can be detected by checking its offset against its section's size.
  *
  * The section offset values are relative to DICE_PRIVATE_SPACE; the offset/
  * size values are measured in quadlets.  Read-only.
  */
 #define DICE_GLOBAL_OFFSET		0x00
 #define DICE_GLOBAL_SIZE		0x04
 #define DICE_TX_OFFSET			0x08
 #define DICE_TX_SIZE			0x0c
 #define DICE_RX_OFFSET			0x10
 #define DICE_RX_SIZE			0x14
 #define DICE_EXT_SYNC_OFFSET		0x18
 #define DICE_EXT_SYNC_SIZE		0x1c
 #define DICE_UNUSED2_OFFSET		0x20
 #define DICE_UNUSED2_SIZE		0x24

 /*
  * Global settings.
  */

 /*
  * Stores the full 64-bit address (node ID and offset in the node's address
  * space) where the device will send notifications.  Must be changed with
  * a compare/swap transaction by the owner.  This register is automatically
  * cleared on a bus reset.
  */
 #define GLOBAL_OWNER			0x000
 #define  OWNER_NO_OWNER			0xffff000000000000uLL
 #define  OWNER_NODE_SHIFT		48

 /*
  * A bitmask with asynchronous events; read-only.  When any event(s) happen,
  * the bits of previous events are cleared, and the value of this register is
  * also written to the address stored in the owner register.
  */
 #define GLOBAL_NOTIFICATION		0x008
 /* Some registers in the Rx/Tx sections may have changed. */
 #define  NOTIFY_RX_CFG_CHG		0x00000001
 #define  NOTIFY_TX_CFG_CHG		0x00000002
 /* Lock status of the current clock source may have changed. */
 #define  NOTIFY_LOCK_CHG		0x00000010
 /* Write to the clock select register has been finished. */
 #define  NOTIFY_CLOCK_ACCEPTED		0x00000020
 /* Lock status of some clock source has changed. */
 #define  NOTIFY_EXT_STATUS		0x00000040
 /* Other bits may be used for device-specific events. */

 /*
  * A name that can be customized for each device; read/write.  Padded with zero
  * bytes.  Quadlets are byte-swapped.  The encoding is whatever the host driver
  * happens to be using.
  */
 #define GLOBAL_NICK_NAME		0x00c
 #define  NICK_NAME_SIZE			64

 /*
  * The current sample rate and clock source; read/write.  Whether a clock
  * source or sample rate is supported is device-specific; the internal clock
  * source is always available.  Low/mid/high = up to 48/96/192 kHz.  This
  * register can be changed even while streams are running.
  */
 #define GLOBAL_CLOCK_SELECT		0x04c
 #define  CLOCK_SOURCE_MASK		0x000000ff
 #define  CLOCK_SOURCE_AES1		0x00000000
 #define  CLOCK_SOURCE_AES2		0x00000001
 #define  CLOCK_SOURCE_AES3		0x00000002
 #define  CLOCK_SOURCE_AES4		0x00000003
 #define  CLOCK_SOURCE_AES_ANY		0x00000004
 #define  CLOCK_SOURCE_ADAT		0x00000005
 #define  CLOCK_SOURCE_TDIF		0x00000006
 #define  CLOCK_SOURCE_WC		0x00000007
 #define  CLOCK_SOURCE_ARX1		0x00000008
 #define  CLOCK_SOURCE_ARX2		0x00000009
 #define  CLOCK_SOURCE_ARX3		0x0000000a
 #define  CLOCK_SOURCE_ARX4		0x0000000b
 #define  CLOCK_SOURCE_INTERNAL		0x0000000c
 #define  CLOCK_RATE_MASK		0x0000ff00
 #define  CLOCK_RATE_32000		0x00000000
 #define  CLOCK_RATE_44100		0x00000100
 #define  CLOCK_RATE_48000		0x00000200
 #define  CLOCK_RATE_88200		0x00000300
 #define  CLOCK_RATE_96000		0x00000400
 #define  CLOCK_RATE_176400		0x00000500
 #define  CLOCK_RATE_192000		0x00000600
 #define  CLOCK_RATE_ANY_LOW		0x00000700
 #define  CLOCK_RATE_ANY_MID		0x00000800
 #define  CLOCK_RATE_ANY_HIGH		0x00000900
 #define  CLOCK_RATE_NONE		0x00000a00
 #define  CLOCK_RATE_SHIFT		8

 /*
  * Enable streaming; read/write.  Writing a non-zero value (re)starts all
  * streams that have a valid iso channel set; zero stops all streams.  The
  * streams' parameters must be configured before starting.  This register is
  * automatically cleared on a bus reset.
  */
 #define GLOBAL_ENABLE			0x050

 /*
  * Status of the sample clock; read-only.
  */
 #define GLOBAL_STATUS			0x054
 /* The current clock source is locked. */
 #define  STATUS_SOURCE_LOCKED		0x00000001
 /* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */
 #define  STATUS_NOMINAL_RATE_MASK	0x0000ff00

 /*
  * Status of all clock sources; read-only.
  */
 #define GLOBAL_EXTENDED_STATUS		0x058
 /*
  * The _LOCKED bits always show the current status; any change generates
  * a notification.
  */
 #define  EXT_STATUS_AES1_LOCKED		0x00000001
 #define  EXT_STATUS_AES2_LOCKED		0x00000002
 #define  EXT_STATUS_AES3_LOCKED		0x00000004
 #define  EXT_STATUS_AES4_LOCKED		0x00000008
 #define  EXT_STATUS_ADAT_LOCKED		0x00000010
 #define  EXT_STATUS_TDIF_LOCKED		0x00000020
 #define  EXT_STATUS_ARX1_LOCKED		0x00000040
 #define  EXT_STATUS_ARX2_LOCKED		0x00000080
 #define  EXT_STATUS_ARX3_LOCKED		0x00000100
 #define  EXT_STATUS_ARX4_LOCKED		0x00000200
 #define  EXT_STATUS_WC_LOCKED		0x00000400
 /*
  * The _SLIP bits do not generate notifications; a set bit indicates that an
  * error occurred since the last time when this register was read with
  * a quadlet read transaction.
  */
 #define  EXT_STATUS_AES1_SLIP		0x00010000
 #define  EXT_STATUS_AES2_SLIP		0x00020000
 #define  EXT_STATUS_AES3_SLIP		0x00040000
 #define  EXT_STATUS_AES4_SLIP		0x00080000
 #define  EXT_STATUS_ADAT_SLIP		0x00100000
 #define  EXT_STATUS_TDIF_SLIP		0x00200000
 #define  EXT_STATUS_ARX1_SLIP		0x00400000
 #define  EXT_STATUS_ARX2_SLIP		0x00800000
 #define  EXT_STATUS_ARX3_SLIP		0x01000000
 #define  EXT_STATUS_ARX4_SLIP		0x02000000
 #define  EXT_STATUS_WC_SLIP		0x04000000

 /*
  * The measured rate of the current clock source, in Hz; read-only.
  */
 #define GLOBAL_SAMPLE_RATE		0x05c

 /*
  * The version of the DICE driver specification that this device conforms to;
  * read-only.
  */
 #define GLOBAL_VERSION			0x060

 /* Some old firmware versions do not have the following global registers: */

 /*
  * Supported sample rates and clock sources; read-only.
  */
 #define GLOBAL_CLOCK_CAPABILITIES	0x064
 #define  CLOCK_CAP_RATE_32000		0x00000001
 #define  CLOCK_CAP_RATE_44100		0x00000002
 #define  CLOCK_CAP_RATE_48000		0x00000004
 #define  CLOCK_CAP_RATE_88200		0x00000008
 #define  CLOCK_CAP_RATE_96000		0x00000010
 #define  CLOCK_CAP_RATE_176400		0x00000020
 #define  CLOCK_CAP_RATE_192000		0x00000040
 #define  CLOCK_CAP_SOURCE_AES1		0x00010000
 #define  CLOCK_CAP_SOURCE_AES2		0x00020000
 #define  CLOCK_CAP_SOURCE_AES3		0x00040000
 #define  CLOCK_CAP_SOURCE_AES4		0x00080000
 #define  CLOCK_CAP_SOURCE_AES_ANY	0x00100000
 #define  CLOCK_CAP_SOURCE_ADAT		0x00200000
 #define  CLOCK_CAP_SOURCE_TDIF		0x00400000
 #define  CLOCK_CAP_SOURCE_WC		0x00800000
 #define  CLOCK_CAP_SOURCE_ARX1		0x01000000
 #define  CLOCK_CAP_SOURCE_ARX2		0x02000000
 #define  CLOCK_CAP_SOURCE_ARX3		0x04000000
 #define  CLOCK_CAP_SOURCE_ARX4		0x08000000
 #define  CLOCK_CAP_SOURCE_INTERNAL	0x10000000

 /*
  * Names of all clock sources; read-only.  Quadlets are byte-swapped.  Names
  * are separated with one backslash, the list is terminated with two
  * backslashes.  Unused clock sources are included.
  */
 #define GLOBAL_CLOCK_SOURCE_NAMES	0x068
 #define  CLOCK_SOURCE_NAMES_SIZE	256

 /*
  * Capture stream settings.  This section includes the number/size registers
  * and the registers of all streams.
  */

 /*
  * The number of supported capture streams; read-only.
  */
 #define TX_NUMBER			0x000

 /*
  * The size of one stream's register block, in quadlets; read-only.  The
  * registers of the first stream follow immediately afterwards; the registers
  * of the following streams are offset by this register's value.
  */
 #define TX_SIZE				0x004

 /*
  * The isochronous channel number on which packets are sent, or -1 if the
  * stream is not to be used; read/write.
  */
 #define TX_ISOCHRONOUS			0x008

 /*
  * The number of audio channels; read-only.  There will be one quadlet per
  * channel; the first channel is the first quadlet in a data block.
  */
 #define TX_NUMBER_AUDIO			0x00c

 /*
  * The number of MIDI ports, 0-8; read-only.  If > 0, there will be one
  * additional quadlet in each data block, following the audio quadlets.
  */
 #define TX_NUMBER_MIDI			0x010

 /*
  * The speed at which the packets are sent, SCODE_100-_400; read/write.
  */
 #define TX_SPEED			0x014

 /*
  * Names of all audio channels; read-only.  Quadlets are byte-swapped.  Names
  * are separated with one backslash, the list is terminated with two
  * backslashes.
  */
 #define TX_NAMES			0x018
 #define  TX_NAMES_SIZE			256

 /*
  * Audio IEC60958 capabilities; read-only.  Bitmask with one bit per audio
  * channel.
  */
 #define TX_AC3_CAPABILITIES		0x118

 /*
  * Send audio data with IEC60958 label; read/write.  Bitmask with one bit per
  * audio channel.  This register can be changed even while the stream is
  * running.
  */
 #define TX_AC3_ENABLE			0x11c

 /*
  * Playback stream settings.  This section includes the number/size registers
  * and the registers of all streams.
  */

 /*
  * The number of supported playback streams; read-only.
  */
 #define RX_NUMBER			0x000

 /*
  * The size of one stream's register block, in quadlets; read-only.  The
  * registers of the first stream follow immediately afterwards; the registers
  * of the following streams are offset by this register's value.
  */
 #define RX_SIZE				0x004

 /*
  * The isochronous channel number on which packets are received, or -1 if the
  * stream is not to be used; read/write.
  */
 #define RX_ISOCHRONOUS			0x008

 /*
  * Index of first quadlet to be interpreted; read/write.  If > 0, that many
  * quadlets at the beginning of each data block will be ignored, and all the
  * audio and MIDI quadlets will follow.
  */
 #define RX_SEQ_START			0x00c

 /*
  * The number of audio channels; read-only.  There will be one quadlet per
  * channel.
  */
 #define RX_NUMBER_AUDIO			0x010

 /*
  * The number of MIDI ports, 0-8; read-only.  If > 0, there will be one
  * additional quadlet in each data block, following the audio quadlets.
  */
 #define RX_NUMBER_MIDI			0x014

 /*
  * Names of all audio channels; read-only.  Quadlets are byte-swapped.  Names
  * are separated with one backslash, the list is terminated with two
  * backslashes.
  */
 #define RX_NAMES			0x018
 #define  RX_NAMES_SIZE			256

 /*
  * Audio IEC60958 capabilities; read-only.  Bitmask with one bit per audio
  * channel.
  */
 #define RX_AC3_CAPABILITIES		0x118

 /*
  * Receive audio data with IEC60958 label; read/write.  Bitmask with one bit
  * per audio channel.  This register can be changed even while the stream is
  * running.
  */
 #define RX_AC3_ENABLE			0x11c

 /*
  * Extended synchronization information.
  * This section can be read completely with a block read request.
  */

 /*
  * Current clock source; read-only.
  */
 #define EXT_SYNC_CLOCK_SOURCE		0x000

 /*
  * Clock source is locked (boolean); read-only.
  */
 #define EXT_SYNC_LOCKED			0x004

 /*
  * Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or
  * _NONE; read-only.
  */
 #define EXT_SYNC_RATE			0x008

 /*
  * ADAT user data bits; read-only.
  */
 #define EXT_SYNC_ADAT_USER_DATA		0x00c
 /* The data bits, if available. */
 #define  ADAT_USER_DATA_MASK		0x0f
 /* The data bits are not available. */
 #define  ADAT_USER_DATA_NO_DATA		0x10

 #endif
	#ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED
	#define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED

	/*
	* DICE device interface definitions
	*/

	/*
	* Generally, all registers can be read like memory, i.e., with quadlet read or
	* block read transactions with at least quadlet-aligned offset and length.
	* Writes are not allowed except where noted; quadlet-sized registers must be
	* written with a quadlet write transaction.
	*
	* All values are in big endian. The DICE firmware runs on a little-endian CPU
	* and just byte-swaps _all_ quadlets on the bus, so values without endianness
	* (e.g. strings) get scrambled and must be byte-swapped again by the driver.
	*/

	/*
	* Streaming is handled by the "DICE driver" interface. Its registers are
	* located in this private address space.
	*/
	#define DICE_PRIVATE_SPACE 0xffffe0000000uLL

	/*
	* The registers are organized in several sections, which are organized
	* separately to allow them to be extended individually. Whether a register is
	* supported can be detected by checking its offset against its section's size.
	*
	* The section offset values are relative to DICE_PRIVATE_SPACE; the offset/
	* size values are measured in quadlets. Read-only.
	*/
	#define DICE_GLOBAL_OFFSET 0x00
	#define DICE_GLOBAL_SIZE 0x04
	#define DICE_TX_OFFSET 0x08
	#define DICE_TX_SIZE 0x0c
	#define DICE_RX_OFFSET 0x10
	#define DICE_RX_SIZE 0x14
	#define DICE_EXT_SYNC_OFFSET 0x18
	#define DICE_EXT_SYNC_SIZE 0x1c
	#define DICE_UNUSED2_OFFSET 0x20
	#define DICE_UNUSED2_SIZE 0x24

	/*
	* Global settings.
	*/

	/*
	* Stores the full 64-bit address (node ID and offset in the node's address
	* space) where the device will send notifications. Must be changed with
	* a compare/swap transaction by the owner. This register is automatically
	* cleared on a bus reset.
	*/
	#define GLOBAL_OWNER 0x000
	#define OWNER_NO_OWNER 0xffff000000000000uLL
	#define OWNER_NODE_SHIFT 48

	/*
	* A bitmask with asynchronous events; read-only. When any event(s) happen,
	* the bits of previous events are cleared, and the value of this register is
	* also written to the address stored in the owner register.
	*/
	#define GLOBAL_NOTIFICATION 0x008
	/* Some registers in the Rx/Tx sections may have changed. */
	#define NOTIFY_RX_CFG_CHG 0x00000001
	#define NOTIFY_TX_CFG_CHG 0x00000002
	/* Lock status of the current clock source may have changed. */
	#define NOTIFY_LOCK_CHG 0x00000010
	/* Write to the clock select register has been finished. */
	#define NOTIFY_CLOCK_ACCEPTED 0x00000020
	/* Lock status of some clock source has changed. */
	#define NOTIFY_EXT_STATUS 0x00000040
	/* Other bits may be used for device-specific events. */

	/*
	* A name that can be customized for each device; read/write. Padded with zero
	* bytes. Quadlets are byte-swapped. The encoding is whatever the host driver
	* happens to be using.
	*/
	#define GLOBAL_NICK_NAME 0x00c
	#define NICK_NAME_SIZE 64

	/*
	* The current sample rate and clock source; read/write. Whether a clock
	* source or sample rate is supported is device-specific; the internal clock
	* source is always available. Low/mid/high = up to 48/96/192 kHz. This
	* register can be changed even while streams are running.
	*/
	#define GLOBAL_CLOCK_SELECT 0x04c
	#define CLOCK_SOURCE_MASK 0x000000ff
	#define CLOCK_SOURCE_AES1 0x00000000
	#define CLOCK_SOURCE_AES2 0x00000001
	#define CLOCK_SOURCE_AES3 0x00000002
	#define CLOCK_SOURCE_AES4 0x00000003
	#define CLOCK_SOURCE_AES_ANY 0x00000004
	#define CLOCK_SOURCE_ADAT 0x00000005
	#define CLOCK_SOURCE_TDIF 0x00000006
	#define CLOCK_SOURCE_WC 0x00000007
	#define CLOCK_SOURCE_ARX1 0x00000008
	#define CLOCK_SOURCE_ARX2 0x00000009
	#define CLOCK_SOURCE_ARX3 0x0000000a
	#define CLOCK_SOURCE_ARX4 0x0000000b
	#define CLOCK_SOURCE_INTERNAL 0x0000000c
	#define CLOCK_RATE_MASK 0x0000ff00
	#define CLOCK_RATE_32000 0x00000000
	#define CLOCK_RATE_44100 0x00000100
	#define CLOCK_RATE_48000 0x00000200
	#define CLOCK_RATE_88200 0x00000300
	#define CLOCK_RATE_96000 0x00000400
	#define CLOCK_RATE_176400 0x00000500
	#define CLOCK_RATE_192000 0x00000600
	#define CLOCK_RATE_ANY_LOW 0x00000700
	#define CLOCK_RATE_ANY_MID 0x00000800
	#define CLOCK_RATE_ANY_HIGH 0x00000900
	#define CLOCK_RATE_NONE 0x00000a00
	#define CLOCK_RATE_SHIFT 8

	/*
	* Enable streaming; read/write. Writing a non-zero value (re)starts all
	* streams that have a valid iso channel set; zero stops all streams. The
	* streams' parameters must be configured before starting. This register is
	* automatically cleared on a bus reset.
	*/
	#define GLOBAL_ENABLE 0x050

	/*
	* Status of the sample clock; read-only.
	*/
	#define GLOBAL_STATUS 0x054
	/* The current clock source is locked. */
	#define STATUS_SOURCE_LOCKED 0x00000001
	/* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */
	#define STATUS_NOMINAL_RATE_MASK 0x0000ff00

	/*
	* Status of all clock sources; read-only.
	*/
	#define GLOBAL_EXTENDED_STATUS 0x058
	/*
	* The _LOCKED bits always show the current status; any change generates
	* a notification.
	*/
	#define EXT_STATUS_AES1_LOCKED 0x00000001
	#define EXT_STATUS_AES2_LOCKED 0x00000002
	#define EXT_STATUS_AES3_LOCKED 0x00000004
	#define EXT_STATUS_AES4_LOCKED 0x00000008
	#define EXT_STATUS_ADAT_LOCKED 0x00000010
	#define EXT_STATUS_TDIF_LOCKED 0x00000020
	#define EXT_STATUS_ARX1_LOCKED 0x00000040
	#define EXT_STATUS_ARX2_LOCKED 0x00000080
	#define EXT_STATUS_ARX3_LOCKED 0x00000100
	#define EXT_STATUS_ARX4_LOCKED 0x00000200
	#define EXT_STATUS_WC_LOCKED 0x00000400
	/*
	* The _SLIP bits do not generate notifications; a set bit indicates that an
	* error occurred since the last time when this register was read with
	* a quadlet read transaction.
	*/
	#define EXT_STATUS_AES1_SLIP 0x00010000
	#define EXT_STATUS_AES2_SLIP 0x00020000
	#define EXT_STATUS_AES3_SLIP 0x00040000
	#define EXT_STATUS_AES4_SLIP 0x00080000
	#define EXT_STATUS_ADAT_SLIP 0x00100000
	#define EXT_STATUS_TDIF_SLIP 0x00200000
	#define EXT_STATUS_ARX1_SLIP 0x00400000
	#define EXT_STATUS_ARX2_SLIP 0x00800000
	#define EXT_STATUS_ARX3_SLIP 0x01000000
	#define EXT_STATUS_ARX4_SLIP 0x02000000
	#define EXT_STATUS_WC_SLIP 0x04000000

	/*
	* The measured rate of the current clock source, in Hz; read-only.
	*/
	#define GLOBAL_SAMPLE_RATE 0x05c

	/*
	* The version of the DICE driver specification that this device conforms to;
	* read-only.
	*/
	#define GLOBAL_VERSION 0x060

	/* Some old firmware versions do not have the following global registers: */

	/*
	* Supported sample rates and clock sources; read-only.
	*/
	#define GLOBAL_CLOCK_CAPABILITIES 0x064
	#define CLOCK_CAP_RATE_32000 0x00000001
	#define CLOCK_CAP_RATE_44100 0x00000002
	#define CLOCK_CAP_RATE_48000 0x00000004
	#define CLOCK_CAP_RATE_88200 0x00000008
	#define CLOCK_CAP_RATE_96000 0x00000010
	#define CLOCK_CAP_RATE_176400 0x00000020
	#define CLOCK_CAP_RATE_192000 0x00000040
	#define CLOCK_CAP_SOURCE_AES1 0x00010000
	#define CLOCK_CAP_SOURCE_AES2 0x00020000
	#define CLOCK_CAP_SOURCE_AES3 0x00040000
	#define CLOCK_CAP_SOURCE_AES4 0x00080000
	#define CLOCK_CAP_SOURCE_AES_ANY 0x00100000
	#define CLOCK_CAP_SOURCE_ADAT 0x00200000
	#define CLOCK_CAP_SOURCE_TDIF 0x00400000
	#define CLOCK_CAP_SOURCE_WC 0x00800000
	#define CLOCK_CAP_SOURCE_ARX1 0x01000000
	#define CLOCK_CAP_SOURCE_ARX2 0x02000000
	#define CLOCK_CAP_SOURCE_ARX3 0x04000000
	#define CLOCK_CAP_SOURCE_ARX4 0x08000000
	#define CLOCK_CAP_SOURCE_INTERNAL 0x10000000

	/*
	* Names of all clock sources; read-only. Quadlets are byte-swapped. Names
	* are separated with one backslash, the list is terminated with two
	* backslashes. Unused clock sources are included.
	*/
	#define GLOBAL_CLOCK_SOURCE_NAMES 0x068
	#define CLOCK_SOURCE_NAMES_SIZE 256

	/*
	* Capture stream settings. This section includes the number/size registers
	* and the registers of all streams.
	*/

	/*
	* The number of supported capture streams; read-only.
	*/
	#define TX_NUMBER 0x000

	/*
	* The size of one stream's register block, in quadlets; read-only. The
	* registers of the first stream follow immediately afterwards; the registers
	* of the following streams are offset by this register's value.
	*/
	#define TX_SIZE 0x004

	/*
	* The isochronous channel number on which packets are sent, or -1 if the
	* stream is not to be used; read/write.
	*/
	#define TX_ISOCHRONOUS 0x008

	/*
	* The number of audio channels; read-only. There will be one quadlet per
	* channel; the first channel is the first quadlet in a data block.
	*/
	#define TX_NUMBER_AUDIO 0x00c

	/*
	* The number of MIDI ports, 0-8; read-only. If > 0, there will be one
	* additional quadlet in each data block, following the audio quadlets.
	*/
	#define TX_NUMBER_MIDI 0x010

	/*
	* The speed at which the packets are sent, SCODE_100-_400; read/write.
	*/
	#define TX_SPEED 0x014

	/*
	* Names of all audio channels; read-only. Quadlets are byte-swapped. Names
	* are separated with one backslash, the list is terminated with two
	* backslashes.
	*/
	#define TX_NAMES 0x018
	#define TX_NAMES_SIZE 256

	/*
	* Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio
	* channel.
	*/
	#define TX_AC3_CAPABILITIES 0x118

	/*
	* Send audio data with IEC60958 label; read/write. Bitmask with one bit per
	* audio channel. This register can be changed even while the stream is
	* running.
	*/
	#define TX_AC3_ENABLE 0x11c

	/*
	* Playback stream settings. This section includes the number/size registers
	* and the registers of all streams.
	*/

	/*
	* The number of supported playback streams; read-only.
	*/
	#define RX_NUMBER 0x000

	/*
	* The size of one stream's register block, in quadlets; read-only. The
	* registers of the first stream follow immediately afterwards; the registers
	* of the following streams are offset by this register's value.
	*/
	#define RX_SIZE 0x004

	/*
	* The isochronous channel number on which packets are received, or -1 if the
	* stream is not to be used; read/write.
	*/
	#define RX_ISOCHRONOUS 0x008

	/*
	* Index of first quadlet to be interpreted; read/write. If > 0, that many
	* quadlets at the beginning of each data block will be ignored, and all the
	* audio and MIDI quadlets will follow.
	*/
	#define RX_SEQ_START 0x00c

	/*
	* The number of audio channels; read-only. There will be one quadlet per
	* channel.
	*/
	#define RX_NUMBER_AUDIO 0x010

	/*
	* The number of MIDI ports, 0-8; read-only. If > 0, there will be one
	* additional quadlet in each data block, following the audio quadlets.
	*/
	#define RX_NUMBER_MIDI 0x014

	/*
	* Names of all audio channels; read-only. Quadlets are byte-swapped. Names
	* are separated with one backslash, the list is terminated with two
	* backslashes.
	*/
	#define RX_NAMES 0x018
	#define RX_NAMES_SIZE 256

	/*
	* Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio
	* channel.
	*/
	#define RX_AC3_CAPABILITIES 0x118

	/*
	* Receive audio data with IEC60958 label; read/write. Bitmask with one bit
	* per audio channel. This register can be changed even while the stream is
	* running.
	*/
	#define RX_AC3_ENABLE 0x11c

	/*
	* Extended synchronization information.
	* This section can be read completely with a block read request.
	*/

	/*
	* Current clock source; read-only.
	*/
	#define EXT_SYNC_CLOCK_SOURCE 0x000

	/*
	* Clock source is locked (boolean); read-only.
	*/
	#define EXT_SYNC_LOCKED 0x004

	/*
	* Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or
	* _NONE; read-only.
	*/
	#define EXT_SYNC_RATE 0x008

	/*
	* ADAT user data bits; read-only.
	*/
	#define EXT_SYNC_ADAT_USER_DATA 0x00c
	/* The data bits, if available. */
	#define ADAT_USER_DATA_MASK 0x0f
	/* The data bits are not available. */
	#define ADAT_USER_DATA_NO_DATA 0x10

	#endif