| config MACH_TX39XX |
| bool |
| select MACH_TXX9 |
| select SYS_HAS_CPU_TX39XX |
| |
| config MACH_TX49XX |
| bool |
| select MACH_TXX9 |
| select CEVT_R4K |
| select CSRC_R4K |
| select IRQ_CPU |
| select SYS_HAS_CPU_TX49XX |
| select SYS_SUPPORTS_64BIT_KERNEL |
| |
| config MACH_TXX9 |
| bool |
| select DMA_NONCOHERENT |
| select SWAP_IO_SPACE |
| select SYS_HAS_EARLY_PRINTK |
| select SYS_SUPPORTS_32BIT_KERNEL |
| select SYS_SUPPORTS_LITTLE_ENDIAN |
| select SYS_SUPPORTS_BIG_ENDIAN |
| select GENERIC_HARDIRQS_NO__DO_IRQ |
| |
| config TOSHIBA_JMR3927 |
| bool "Toshiba JMR-TX3927 board" |
| depends on MACH_TX39XX |
| select SOC_TX3927 |
| |
| config TOSHIBA_RBTX4927 |
| bool "Toshiba RBTX49[23]7 board" |
| depends on MACH_TX49XX |
| select SOC_TX4927 |
| # TX4937 is subset of TX4938 |
| select SOC_TX4938 |
| help |
| This Toshiba board is based on the TX4927 processor. Say Y here to |
| support this machine type |
| |
| config TOSHIBA_RBTX4938 |
| bool "Toshiba RBTX4938 board" |
| depends on MACH_TX49XX |
| select SOC_TX4938 |
| help |
| This Toshiba board is based on the TX4938 processor. Say Y here to |
| support this machine type |
| |
| config SOC_TX3927 |
| bool |
| select CEVT_TXX9 |
| select HAS_TXX9_SERIAL |
| select HW_HAS_PCI |
| select IRQ_TXX9 |
| select GPIO_TXX9 |
| |
| config SOC_TX4927 |
| bool |
| select CEVT_TXX9 |
| select HAS_TXX9_SERIAL |
| select HW_HAS_PCI |
| select IRQ_TXX9 |
| select PCI_TX4927 |
| select SYS_SUPPORTS_KGDB |
| select GPIO_TXX9 |
| |
| config SOC_TX4938 |
| bool |
| select CEVT_TXX9 |
| select HAS_TXX9_SERIAL |
| select HW_HAS_PCI |
| select IRQ_TXX9 |
| select PCI_TX4927 |
| select SYS_SUPPORTS_KGDB |
| select GPIO_TXX9 |
| |
| config TOSHIBA_FPCIB0 |
| bool "FPCIB0 Backplane Support" |
| depends on PCI && MACH_TXX9 |
| select I8259 |
| |
| config PICMG_PCI_BACKPLANE_DEFAULT |
| bool "Support for PICMG PCI Backplane" |
| depends on PCI && MACH_TXX9 |
| default y if !TOSHIBA_FPCIB0 |
| |
| if TOSHIBA_RBTX4938 |
| |
| comment "Multiplex Pin Select" |
| choice |
| prompt "PIO[58:61]" |
| default TOSHIBA_RBTX4938_MPLEX_PIO58_61 |
| |
| config TOSHIBA_RBTX4938_MPLEX_PIO58_61 |
| bool "PIO" |
| config TOSHIBA_RBTX4938_MPLEX_NAND |
| bool "NAND" |
| config TOSHIBA_RBTX4938_MPLEX_ATA |
| bool "ATA" |
| |
| endchoice |
| |
| config TX4938_NAND_BOOT |
| depends on EXPERIMENTAL && TOSHIBA_RBTX4938_MPLEX_NAND |
| bool "NAND Boot Support (EXPERIMENTAL)" |
| help |
| This is only for Toshiba RBTX4938 reference board, which has NAND IPL. |
| Select this option if you need to use NAND boot. |
| |
| endif |
| |
| config PCI_TX4927 |
| bool |