usb: Move definition of USB_EHCI_BIG_ENDIAN_MMIO et al. out side of the ifs.
When CONFIG_USB_SUPPORT is not selected we get things like:
scripts/kconfig/mconf Kconfig
warning: (MIPS_SEAD3 && PMC_MSP && CPU_CAVIUM_OCTEON) selects USB_EHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
It is much cleaner to make the various system Kconfigs select
USB_EHCI_BIG_ENDIAN_MMIO rather than move the system config
information into USB's Kconfig, but the warnings are annoying.
Eliminate the warning by moving the definition of
USB_EHCI_BIG_ENDIAN_MMIO outside of all the Kconfig if statements.
While we are at it move USB_OHCI_BIG_ENDIAN_DESC,
USB_OHCI_BIG_ENDIAN_MMIO, USB_OHCI_LITTLE_ENDIAN and
USB_EHCI_BIG_ENDIAN_DESC too, as they could very well suffer similar
problems for other systems.
Get rid of the redundant "default n" in USB_OHCI_BIG_ENDIAN_DESC and
USB_OHCI_BIG_ENDIAN_MMIO
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index 73f62ca..2642b8a 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -6,9 +6,26 @@
config USB_ARCH_HAS_OHCI
bool
+config USB_OHCI_BIG_ENDIAN_DESC
+ bool
+
+config USB_OHCI_BIG_ENDIAN_MMIO
+ bool
+
+config USB_OHCI_LITTLE_ENDIAN
+ bool
+ default n if STB03xxx || PPC_MPC52xx
+ default y
+
config USB_ARCH_HAS_EHCI
bool
+config USB_EHCI_BIG_ENDIAN_MMIO
+ bool
+
+config USB_EHCI_BIG_ENDIAN_DESC
+ bool
+
config USB_ARCH_HAS_XHCI
bool
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index cf521d6..0947aac 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -113,12 +113,6 @@
Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
If unsure, say N.
-config USB_EHCI_BIG_ENDIAN_MMIO
- bool
-
-config USB_EHCI_BIG_ENDIAN_DESC
- bool
-
config XPS_USB_HCD_XILINX
bool "Use Xilinx usb host EHCI controller core"
depends on (PPC32 || MICROBLAZE)
@@ -509,20 +503,6 @@
controller. It is needed for low-speed USB 1.0 device
support. All CN6XXX based chips with USB are supported.
-
-config USB_OHCI_BIG_ENDIAN_DESC
- bool
- default n
-
-config USB_OHCI_BIG_ENDIAN_MMIO
- bool
- default n
-
-config USB_OHCI_LITTLE_ENDIAN
- bool
- default n if STB03xxx || PPC_MPC52xx
- default y
-
endif # USB_OHCI_HCD
config USB_UHCI_HCD