ata: sata_mv: fix disk hotplug for Armada 370/XP SoCs
On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the
re-plug events are not detected by the sata_mv driver. This patch fixes
the issue by updating the PHY speed in the LP_PHY_CTL register (0x58)
according to the SControl speed.
Note that this fix is only applied if the compatible string
"marvell,armada-370-sata" is found in the SATA DT node.
Fixes: 9ae6f740b49f ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index 4ec5368..dc9d4b1 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -304,6 +304,7 @@
MV5_LTMODE = 0x30,
MV5_PHY_CTL = 0x0C,
SATA_IFCFG = 0x050,
+ LP_PHY_CTL = 0x058,
MV_M2_PREAMP_MASK = 0x7e0,
@@ -431,6 +432,7 @@
MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */
MV_HP_QUIRK_LED_BLINK_EN = (1 << 12), /* is led blinking enabled? */
+ MV_HP_FIX_LP_PHY_CTL = (1 << 13), /* fix speed in LP_PHY_CTL ? */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
@@ -1358,6 +1360,7 @@
if (ofs != 0xffffffffU) {
void __iomem *addr = mv_ap_base(link->ap) + ofs;
+ struct mv_host_priv *hpriv = link->ap->host->private_data;
if (sc_reg_in == SCR_CONTROL) {
/*
* Workaround for 88SX60x1 FEr SATA#26:
@@ -1374,6 +1377,18 @@
*/
if ((val & 0xf) == 1 || (readl(addr) & 0xf) == 1)
val |= 0xf000;
+
+ if (hpriv->hp_flags & MV_HP_FIX_LP_PHY_CTL) {
+ void __iomem *lp_phy_addr =
+ mv_ap_base(link->ap) + LP_PHY_CTL;
+ /*
+ * Set PHY speed according to SControl speed.
+ */
+ if ((val & 0xf0) == 0x10)
+ writelfl(0x7, lp_phy_addr);
+ else
+ writelfl(0x227, lp_phy_addr);
+ }
}
writelfl(val, addr);
return 0;
@@ -4110,6 +4125,15 @@
if (rc)
goto err;
+ /*
+ * To allow disk hotplug on Armada 370/XP SoCs, the PHY speed must be
+ * updated in the LP_PHY_CTL register.
+ */
+ if (pdev->dev.of_node &&
+ of_device_is_compatible(pdev->dev.of_node,
+ "marvell,armada-370-sata"))
+ hpriv->hp_flags |= MV_HP_FIX_LP_PHY_CTL;
+
/* initialize adapter */
rc = mv_init_host(host);
if (rc)