| Qualcomm Technologies, Inc. SDE KMS |
| |
| Snapdragon Display Engine implements Linux DRM/KMS APIs to drive user |
| interface to different panel interfaces. SDE driver is the core of |
| display subsystem which manage all data paths to different panel interfaces. |
| |
| Required properties |
| - compatible: Must be "qcom,sde-kms" |
| - compatible: "msm-hdmi-audio-codec-rx"; |
| - reg: Offset and length of the register set for the device. |
| - reg-names : Names to refer to register sets related to this device |
| - clocks: List of Phandles for clock device nodes |
| needed by the device. |
| - clock-names: List of clock names needed by the device. |
| - mmagic-supply: Phandle for mmagic mdss supply regulator device node. |
| - vdd-supply: Phandle for vdd regulator device node. |
| - interrupt-parent: Must be core interrupt controller. |
| - interrupts: Interrupt associated with MDSS. |
| - interrupt-controller: Mark the device node as an interrupt controller. |
| - #interrupt-cells: Should be one. The first cell is interrupt number. |
| - iommus: Specifies the SID's used by this context bank. |
| - qcom,sde-sspp-type: Array of strings for SDE source surface pipes type information. |
| A source pipe can be "vig", "rgb", "dma" or "cursor" type. |
| Number of xin ids defined should match the number of offsets |
| defined in property: qcom,sde-sspp-off. |
| - qcom,sde-sspp-off: Array of offset for SDE source surface pipes. The offsets |
| are calculated from register "mdp_phys" defined in |
| reg property + "sde-off". The number of offsets defined here should |
| reflect the amount of pipes that can be active in SDE for |
| this configuration. |
| - qcom,sde-sspp-xin-id: Array of VBIF clients ids (xins) corresponding |
| to the respective source pipes. Number of xin ids |
| defined should match the number of offsets |
| defined in property: qcom,sde-sspp-off. |
| - qcom,sde-ctl-off: Array of offset addresses for the available ctl |
| hw blocks within SDE, these offsets are |
| calculated from register "mdp_phys" defined in |
| reg property. The number of ctl offsets defined |
| here should reflect the number of control paths |
| that can be configured concurrently on SDE for |
| this configuration. |
| - qcom,sde-wb-off: Array of offset addresses for the programmable |
| writeback blocks within SDE. |
| - qcom,sde-wb-xin-id: Array of VBIF clients ids (xins) corresponding |
| to the respective writeback. Number of xin ids |
| defined should match the number of offsets |
| defined in property: qcom,sde-wb-off. |
| - qcom,sde-mixer-off: Array of offset addresses for the available |
| mixer blocks that can drive data to panel |
| interfaces. These offsets are be calculated from |
| register "mdp_phys" defined in reg property. |
| The number of offsets defined should reflect the |
| amount of mixers that can drive data to a panel |
| interface. |
| - qcom,sde-dspp-top-off: Offset address for the dspp top block. |
| The offset is calculated from register "mdp_phys" |
| defined in reg property. |
| - qcom,sde-dspp-off: Array of offset addresses for the available dspp |
| blocks. These offsets are calculated from |
| register "mdp_phys" defined in reg property. |
| - qcom,sde-pp-off: Array of offset addresses for the available |
| pingpong blocks. These offsets are calculated |
| from register "mdp_phys" defined in reg property. |
| - qcom,sde-pp-slave: Array of flags indicating whether each ping pong |
| block may be configured as a pp slave. |
| - qcom,sde-intf-off: Array of offset addresses for the available SDE |
| interface blocks that can drive data to a |
| panel controller. The offsets are calculated |
| from "mdp_phys" defined in reg property. The number |
| of offsets defined should reflect the number of |
| programmable interface blocks available in hardware. |
| - qcom,sde-mixer-blend-op-off Array of offset addresses for the available |
| blending stages. The offsets are relative to |
| qcom,sde-mixer-off. |
| - qcom,sde-mixer-pair-mask Array of mixer numbers that can be paired with |
| mixer number corresponding to the array index. |
| |
| Optional properties: |
| - clock-rate: List of clock rates in Hz. |
| - clock-max-rate: List of maximum clock rate in Hz that this device supports. |
| - qcom,platform-supply-entries: A node that lists the elements of the supply. There |
| can be more than one instance of this binding, |
| in which case the entry would be appended with |
| the supply entry index. |
| e.g. qcom,platform-supply-entry@0 |
| -- reg: offset and length of the register set for the device. |
| -- qcom,supply-name: name of the supply (vdd/vdda/vddio) |
| -- qcom,supply-min-voltage: minimum voltage level (uV) |
| -- qcom,supply-max-voltage: maximum voltage level (uV) |
| -- qcom,supply-enable-load: load drawn (uA) from enabled supply |
| -- qcom,supply-disable-load: load drawn (uA) from disabled supply |
| -- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on |
| -- qcom,supply-post-on-sleep: time to sleep (ms) after turning on |
| -- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off |
| -- qcom,supply-post-off-sleep: time to sleep (ms) after turning off |
| - qcom,sde-sspp-src-size: A u32 value indicates the address range for each sspp. |
| - qcom,sde-mixer-size: A u32 value indicates the address range for each mixer. |
| - qcom,sde-ctl-size: A u32 value indicates the address range for each ctl. |
| - qcom,sde-dspp-size: A u32 value indicates the address range for each dspp. |
| - qcom,sde-intf-size: A u32 value indicates the address range for each intf. |
| - qcom,sde-dsc-size: A u32 value indicates the address range for each dsc. |
| - qcom,sde-cdm-size: A u32 value indicates the address range for each cdm. |
| - qcom,sde-pp-size: A u32 value indicates the address range for each pingpong. |
| - qcom,sde-wb-size: A u32 value indicates the address range for each writeback. |
| - qcom,sde-len: A u32 entry for SDE address range. |
| - qcom,sde-intf-max-prefetch-lines: Array of u32 values for max prefetch lines on |
| each interface. |
| - qcom,sde-sspp-linewidth: A u32 value indicates the max sspp line width. |
| - qcom,sde-mixer-linewidth: A u32 value indicates the max mixer line width. |
| - qcom,sde-wb-linewidth: A u32 value indicates the max writeback line width. |
| - qcom,sde-sspp-scale-size: A u32 value indicates the scaling block size on sspp. |
| - qcom,sde-mixer-blendstages: A u32 value indicates the max mixer blend stages for |
| alpha blending. |
| - qcom,sde-qseed-type: A string entry indiates qseed support on sspp and wb. |
| It supports "qssedv3" and "qseedv2" entries for qseed |
| type. By default "qseedv2" is used if this optional property |
| is not defined. |
| - qcom,sde-csc-type: A string entry indicates csc support on sspp and wb. |
| It supports "csc" and "csc-10bit" entries for csc |
| type. |
| - qcom,sde-highest-bank-bit: A u32 property to indicate GPU/Camera/Video highest memory |
| bank bit used for tile format buffers. |
| - qcom,sde-ubwc-version: Property to specify the UBWC feature version. |
| - qcom,sde-ubwc-static: Property to specify the default UBWC static |
| configuration value. |
| - qcom,sde-ubwc-swizzle: Property to specify the default UBWC swizzle |
| configuration value. |
| - qcom,sde-panic-per-pipe: Boolean property to indicate if panic signal |
| control feature is available on each source pipe. |
| - qcom,sde-has-src-split: Boolean property to indicate if source split |
| feature is available or not. |
| - qcom,sde-has-dim-layer: Boolean property to indicate if mixer has dim layer |
| feature is available or not. |
| - qcom,sde-has-idle-pc: Boolean property to indicate if target has idle |
| power collapse feature available or not. |
| - qcom,sde-has-mixer-gc: Boolean property to indicate if mixer has gamma correction |
| feature available or not. |
| - qcom,sde-has-dest-scaler: Boolean property to indicate if destination scaler |
| feature is available or not. |
| - qcom,sde-max-dest-scaler-input-linewidth: A u32 value indicates the |
| maximum input line width to destination scaler. |
| - qcom,sde-max-dest-scaler-output-linewidth: A u32 value indicates the |
| maximum output line width of destination scaler. |
| - qcom,sde-dest-scaler-top-off: A u32 value provides the |
| offset from mdp base to destination scaler block. |
| - qcom,sde-dest-scaler-top-size: A u32 value indicates the address range for ds top |
| - qcom,sde-dest-scaler-off: Array of u32 offsets indicate the qseed3 scaler blocks |
| offset from destination scaler top offset. |
| - qcom,sde-dest-scaler-size: A u32 value indicates the address range for each scaler block |
| - qcom,sde-sspp-clk-ctrl: Array of offsets describing clk control |
| offsets for dynamic clock gating. 1st value |
| in the array represents offset of the control |
| register. 2nd value represents bit offset within |
| control register. Number of offsets defined should |
| match the number of offsets defined in |
| property: qcom,sde-sspp-off |
| - qcom,sde-sspp-clk-status: Array of offsets describing clk status |
| offsets for dynamic clock gating. 1st value |
| in the array represents offset of the status |
| register. 2nd value represents bit offset within |
| control register. Number of offsets defined should |
| match the number of offsets defined in |
| property: qcom,sde-sspp-off. |
| - qcom,sde-sspp-excl-rect: Array of u32 values indicating exclusion rectangle |
| support on each sspp. |
| - qcom,sde-sspp-smart-dma-priority: Array of u32 values indicating hw pipe |
| priority of secondary rectangles when smart dma |
| is supported. Number of priority values should |
| match the number of offsets defined in |
| qcom,sde-sspp-off node. Zero indicates no support |
| for smart dma for the sspp. |
| - qcom,sde-smart-dma-rev: A string entry indicating the smart dma version |
| supported on the device. Supported entries are |
| "smart_dma_v1" and "smart_dma_v2". |
| - qcom,sde-intf-type: Array of string provides the interface type information. |
| Possible string values |
| "dsi" - dsi display interface |
| "dp" - Display Port interface |
| "hdmi" - HDMI display interface |
| An interface is considered as "none" if interface type |
| is not defined. |
| - qcom,sde-off: SDE offset from "mdp_phys" defined in reg property. |
| - qcom,sde-cdm-off: Array of offset addresses for the available |
| cdm blocks. These offsets will be calculated from |
| register "mdp_phys" defined in reg property. |
| - qcom,sde-vbif-off: Array of offset addresses for the available |
| vbif blocks. These offsets will be calculated from |
| register "vbif_phys" defined in reg property. |
| - qcom,sde-vbif-size: A u32 value indicates the vbif block address range. |
| - qcom,sde-te-off: A u32 offset indicates the te block offset on pingpong. |
| This offset is 0x0 by default. |
| - qcom,sde-te2-off: A u32 offset indicates the te2 block offset on pingpong. |
| - qcom,sde-te-size: A u32 value indicates the te block address range. |
| - qcom,sde-te2-size: A u32 value indicates the te2 block address range. |
| - qcom,sde-dsc-off: A u32 offset indicates the dsc block offset on pingpong. |
| - qcom,sde-dither-off: A u32 offset indicates the dither block offset on pingpong. |
| - qcom,sde-dither-version: A u32 value indicates the dither block version. |
| - qcom,sde-dither-size: A u32 value indicates the dither block address range. |
| - qcom,sde-sspp-vig-blocks: A node that lists the blocks inside the VIG hardware. The |
| block entries will contain the offset and version (if needed) |
| of each feature block. The presence of a block entry |
| indicates that the SSPP VIG contains that feature hardware. |
| e.g. qcom,sde-sspp-vig-blocks |
| -- qcom,sde-vig-csc-off: offset of CSC hardware |
| -- qcom,sde-vig-qseed-off: offset of QSEED hardware |
| -- qcom,sde-vig-qseed-size: A u32 address range for qseed scaler. |
| -- qcom,sde-vig-pcc: offset and version of PCC hardware |
| -- qcom,sde-vig-hsic: offset and version of global PA adjustment |
| -- qcom,sde-vig-memcolor: offset and version of PA memcolor hardware |
| - qcom,sde-sspp-rgb-blocks: A node that lists the blocks inside the RGB hardware. The |
| block entries will contain the offset and version (if needed) |
| of each feature block. The presence of a block entry |
| indicates that the SSPP RGB contains that feature hardware. |
| e.g. qcom,sde-sspp-vig-blocks |
| -- qcom,sde-rgb-scaler-off: offset of RGB scaler hardware |
| -- qcom,sde-rgb-scaler-size: A u32 address range for scaler. |
| -- qcom,sde-rgb-pcc: offset and version of PCC hardware |
| - qcom,sde-dspp-blocks: A node that lists the blocks inside the DSPP hardware. The |
| block entries will contain the offset and version of each |
| feature block. The presence of a block entry indicates that |
| the DSPP contains that feature hardware. |
| e.g. qcom,sde-dspp-blocks |
| -- qcom,sde-dspp-pcc: offset and version of PCC hardware |
| -- qcom,sde-dspp-gc: offset and version of GC hardware |
| -- qcom,sde-dspp-igc: offset and version of IGC hardware |
| -- qcom,sde-dspp-hsic: offset and version of global PA adjustment |
| -- qcom,sde-dspp-memcolor: offset and version of PA memcolor hardware |
| -- qcom,sde-dspp-sixzone: offset and version of PA sixzone hardware |
| -- qcom,sde-dspp-gamut: offset and version of Gamut mapping hardware |
| -- qcom,sde-dspp-dither: offset and version of dither hardware |
| -- qcom,sde-dspp-hist: offset and version of histogram hardware |
| -- qcom,sde-dspp-vlut: offset and version of PA vLUT hardware |
| - qcom,sde-mixer-blocks: A node that lists the blocks inside the layer mixer hardware. The |
| block entries will contain the offset and version (if needed) |
| of each feature block. The presence of a block entry |
| indicates that the layer mixer contains that feature hardware. |
| e.g. qcom,sde-mixer-blocks |
| -- qcom,sde-mixer-gc: offset and version of mixer GC hardware |
| - qcom,sde-dspp-ad-off: Array of u32 offsets indicate the ad block offset from the |
| DSPP offset. Since AD hardware is represented as part of |
| DSPP block, the AD offsets must be offset from the |
| corresponding DSPP base. |
| - qcom,sde-dspp-ad-version A u32 value indicating the version of the AD hardware |
| - qcom,sde-vbif-id: Array of vbif ids corresponding to the |
| offsets defined in property: qcom,sde-vbif-off. |
| - qcom,sde-vbif-default-ot-rd-limit: A u32 value indicates the default read OT limit |
| - qcom,sde-vbif-default-ot-wr-limit: A u32 value indicates the default write OT limit |
| - qcom,sde-vbif-dynamic-ot-rd-limit: A series of 2 cell property, with a format |
| of (pps, OT limit), where pps is pixel per second and |
| OT limit is the read limit to apply if the given |
| pps is not exceeded. |
| - qcom,sde-vbif-dynamic-ot-wr-limit: A series of 2 cell property, with a format |
| of (pps, OT limit), where pps is pixel per second and |
| OT limit is the write limit to apply if the given |
| pps is not exceeded. |
| - qcom,sde-vbif-memtype-0: Array of u32 vbif memory type settings, group 0 |
| - qcom,sde-vbif-memtype-1: Array of u32 vbif memory type settings, group 1 |
| - qcom,sde-wb-id: Array of writeback ids corresponding to the |
| offsets defined in property: qcom,sde-wb-off. |
| - qcom,sde-wb-clk-ctrl: Array of 2 cell property describing clk control |
| offsets for dynamic clock gating. 1st value |
| in the array represents offset of the control |
| register. 2nd value represents bit offset within |
| control register. Number of offsets defined should |
| match the number of offsets defined in |
| property: qcom,sde-wb-off |
| - qcom,sde-reg-dma-off: Offset of the register dma hardware block from |
| "regdma_phys" defined in reg property. |
| - qcom,sde-reg-dma-version: Version of the reg dma hardware block. |
| - qcom,sde-reg-dma-trigger-off: Offset of the lut dma trigger reg from "mdp_phys" |
| defined in reg property. |
| - qcom,sde-dram-channels: This represents the number of channels in the |
| Bus memory controller. |
| - qcom,sde-num-nrt-paths: Integer property represents the number of non-realtime |
| paths in each Bus Scaling Usecase. This value depends on |
| number of AXI ports that are dedicated to non-realtime VBIF |
| for particular chipset. |
| These paths must be defined after rt-paths in |
| "qcom,msm-bus,vectors-KBps" vector request. |
| - qcom,sde-max-bw-low-kbps: This value indicates the max bandwidth in Kbps |
| that can be supported without underflow. |
| This is a low bandwidth threshold which should |
| be applied in most scenarios to be safe from |
| underflows when unable to satisfy bandwidth |
| requirements. |
| - qcom,sde-max-bw-high-kbps: This value indicates the max bandwidth in Kbps |
| that can be supported without underflow. |
| This is a high bandwidth threshold which can be |
| applied in scenarios where panel interface can |
| be more tolerant to memory latency such as |
| command mode panels. |
| - qcom,sde-core-ib-ff: A string entry indicating the fudge factor for |
| core ib calculation. |
| - qcom,sde-core-clk-ff: A string entry indicating the fudge factor for |
| core clock calculation. |
| - qcom,sde-min-core-ib-kbps: This u32 value indicates the minimum mnoc ib |
| vote in Kbps that can be reduced without hitting underflow. |
| BW calculation logic will choose the IB bandwidth requirement |
| based on usecase if this floor value is not defined. |
| - qcom,sde-min-llcc-ib-kbps: This u32 value indicates the minimum llcc ib |
| vote in Kbps that can be reduced without hitting underflow. |
| BW calculation logic will choose the IB bandwidth requirement |
| based on usecase if this floor value is not defined. |
| - qcom,sde-min-dram-ib-kbps: This u32 value indicates the minimum dram ib |
| vote in Kbps that can be reduced without hitting underflow. |
| BW calculation logic will choose the IB bandwidth requirement |
| based on usecase if this floor value is not defined. |
| - qcom,sde-comp-ratio-rt: A string entry indicating the compression ratio |
| for each supported compressed format on realtime interface. |
| The string is composed of one or more of |
| <fourcc code>/<vendor code>/<modifier>/<compression ratio> |
| separated with spaces. |
| - qcom,sde-comp-ratio-nrt: A string entry indicating the compression ratio |
| for each supported compressed format on non-realtime interface. |
| The string is composed of one or more of |
| <fourcc code>/<vendor code>/<modifier>/<compression ratio> |
| separated with spaces. |
| - qcom,sde-undersized-prefill-lines: A u32 value indicates the size of undersized prefill in lines. |
| - qcom,sde-xtra-prefill-lines: A u32 value indicates the extra prefill in lines. |
| - qcom,sde-dest-scale-prefill-lines: A u32 value indicates the latency of destination scaler in lines. |
| - qcom,sde-macrotile-prefill-lines: A u32 value indicates the latency of macrotile in lines. |
| - qcom,sde-yuv-nv12-prefill-lines: A u32 value indicates the latency of yuv/nv12 in lines. |
| - qcom,sde-linear-prefill-lines: A u32 value indicates the latency of linear in lines. |
| - qcom,sde-downscaling-prefill-lines: A u32 value indicates the latency of downscaling in lines. |
| - qcom,sde-max-per-pipe-bw-kbps: Array of u32 value indicates the max per pipe bandwidth in Kbps. |
| - qcom,sde-amortizable-threshold: This value indicates the min for traffic shaping in lines. |
| - qcom,sde-vbif-qos-rt-remap: This array is used to program vbif qos remapper register |
| priority for realtime clients. |
| - qcom,sde-vbif-qos-nrt-remap: This array is used to program vbif qos remapper register |
| priority for non-realtime clients. |
| - qcom,sde-danger-lut: A 4 cell property, with a format of <linear, |
| tile, nrt, cwb>, |
| indicating the danger luts on sspp. |
| - qcom,sde-safe-lut-linear: Array of 2 cell property, with a format of |
| <fill level, lut> in ascending fill level |
| indicating the safe luts for linear format on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-safe-lut-macrotile: Array of 2 cell property, with a format of |
| <fill level, lut> in ascending fill level |
| indicating the safe luts for macrotile format on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-safe-lut-nrt: Array of 2 cell property, with a format of |
| <fill level, lut> in ascending fill level |
| indicating the safe luts for nrt (e.g wfd) on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-safe-lut-cwb: Array of 2 cell property, with a format of |
| <fill level, lut> in ascending fill level |
| indicating the safe luts for cwb on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-qos-lut-linear: Array of 3 cell property, with a format of |
| <fill level, lut hi, lut lo> in ascending fill level |
| indicating the qos luts for linear format on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-qos-lut-macrotile: Array of 3 cell property, with a format of |
| <fill level, lut hi, lut lo> in ascending fill level |
| indicating the qos luts for macrotile format on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-qos-lut-nrt: Array of 3 cell property, with a format of |
| <fill level, lut hi, lut lo> in ascending fill level |
| indicating the qos luts for nrt (e.g wfd) on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-qos-lut-cwb: Array of 3 cell property, with a format of |
| <fill level, lut hi, lut lo> in ascending fill level |
| indicating the qos luts for cwb on sspp. |
| Zero fill level on the last entry identifies the default lut. |
| - qcom,sde-cdp-setting: Array of 2 cell property, with a format of |
| <read enable, write enable> for cdp use cases in |
| order of <real_time>, and <non_real_time>. |
| - qcom,sde-qos-cpu-mask: A u32 value indicating desired PM QoS CPU affine mask. |
| - qcom,sde-qos-cpu-dma-latency: A u32 value indicating desired PM QoS CPU DMA latency in usec. |
| - qcom,sde-inline-rot-xin: An integer array of xin-ids related to inline |
| rotation. |
| - qcom,sde-inline-rot-xin-type: A string array indicating the type of xin, |
| namely sspp or wb. Number of entries should match |
| the number of xin-ids defined in |
| property: qcom,sde-inline-rot-xin |
| - qcom,sde-inline-rot-clk-ctrl: Array of offsets describing clk control |
| offsets for dynamic clock gating. 1st value |
| in the array represents offset of the control |
| register. 2nd value represents bit offset within |
| control register. Number of offsets defined should |
| match the number of xin-ids defined in |
| property: qcom,sde-inline-rot-xin |
| - #power-domain-cells: Number of cells in a power-domain specifier and should contain 0. |
| - qcom,sde-mixer-display-pref: A string array indicating the preferred display type |
| for the mixer block. Possible values: |
| "primary" - preferred for primary display |
| "none" - no preference on display |
| - qcom,sde-ctl-display-pref: A string array indicating the preferred display type |
| for the ctl block. Possible values: |
| "primary" - preferred for primary display |
| "none" - no preference on display |
| |
| Bus Scaling Subnodes: |
| - qcom,sde-reg-bus: Property to provide Bus scaling for register access for |
| mdss blocks. |
| - qcom,sde-data-bus: Property to provide Bus scaling for data bus access for |
| mdss blocks. |
| - qcom,sde-llcc-bus: Property to provide Bus scaling for data bus access for |
| mnoc to llcc. |
| - qcom,sde-ebi-bus: Property to provide Bus scaling for data bus access for |
| llcc to ebi. |
| |
| - qcom,sde-inline-rotator: A 2 cell property, with format of (rotator phandle, |
| instance id), of inline rotator device. |
| |
| Bus Scaling Data: |
| - qcom,msm-bus,name: String property describing client name. |
| - qcom,msm-bus,num-cases: This is the number of Bus Scaling use cases |
| defined in the vectors property. |
| - qcom,msm-bus,num-paths: This represents the number of paths in each |
| Bus Scaling Usecase. |
| - qcom,msm-bus,vectors-KBps: * A series of 4 cell properties, with a format |
| of (src, dst, ab, ib) which is defined at |
| Documentation/devicetree/bindings/arm/msm/msm_bus.txt |
| * Current values of src & dst are defined at |
| include/linux/msm-bus-board.h |
| |
| SMMU Subnodes: |
| - smmu_sde_****: Child nodes representing sde smmu virtual |
| devices |
| |
| Subnode properties: |
| - compatible: Compatible names used for smmu devices. |
| names should be: |
| "qcom,smmu_sde_unsec": smmu context bank device |
| for unsecure sde real time domain. |
| "qcom,smmu_sde_sec": smmu context bank device |
| for secure sde real time domain. |
| "qcom,smmu_sde_nrt_unsec": smmu context bank device |
| for unsecure sde non-real time domain. |
| "qcom,smmu_sde_nrt_sec": smmu context bank device |
| for secure sde non-real time domain. |
| |
| |
| Please refer to ../../interrupt-controller/interrupts.txt for a general |
| description of interrupt bindings. |
| |
| Example: |
| mdss_mdp: qcom,mdss_mdp@900000 { |
| compatible = "qcom,sde-kms"; |
| reg = <0x00900000 0x90000>, |
| <0x009b0000 0x1040>, |
| <0x009b8000 0x1040>, |
| <0x0aeac000 0x00f0>; |
| reg-names = "mdp_phys", |
| "vbif_phys", |
| "vbif_nrt_phys", |
| "regdma_phys"; |
| clocks = <&clock_mmss clk_mdss_ahb_clk>, |
| <&clock_mmss clk_mdss_axi_clk>, |
| <&clock_mmss clk_mdp_clk_src>, |
| <&clock_mmss clk_mdss_mdp_vote_clk>, |
| <&clock_mmss clk_smmu_mdp_axi_clk>, |
| <&clock_mmss clk_mmagic_mdss_axi_clk>, |
| <&clock_mmss clk_mdss_vsync_clk>; |
| clock-names = "iface_clk", |
| "bus_clk", |
| "core_clk_src", |
| "core_clk", |
| "iommu_clk", |
| "mmagic_clk", |
| "vsync_clk"; |
| clock-rate = <0>, <0>, <0>; |
| clock-max-rate= <0 320000000 0>; |
| mmagic-supply = <&gdsc_mmagic_mdss>; |
| vdd-supply = <&gdsc_mdss>; |
| interrupt-parent = <&intc>; |
| interrupts = <0 83 0>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| iommus = <&mdp_smmu 0>; |
| #power-domain-cells = <0>; |
| |
| qcom,sde-off = <0x1000>; |
| qcom,sde-ctl-off = <0x00002000 0x00002200 0x00002400 |
| 0x00002600 0x00002800>; |
| qcom,sde-ctl-display-pref = "primary", "none", "none", |
| "none", "none"; |
| qcom,sde-mixer-off = <0x00045000 0x00046000 |
| 0x00047000 0x0004a000>; |
| qcom,sde-mixer-display-pref = "primary", "none", |
| "none", "none"; |
| qcom,sde-dspp-top-off = <0x1300>; |
| qcom,sde-dspp-off = <0x00055000 0x00057000>; |
| qcom,sde-dspp-ad-off = <0x24000 0x22800>; |
| qcom,sde-dspp-ad-version = <0x00030000>; |
| qcom,sde-dest-scaler-top-off = <0x00061000>; |
| qcom,sde-dest-scaler-off = <0x800 0x1000>; |
| qcom,sde-wb-off = <0x00066000>; |
| qcom,sde-wb-xin-id = <6>; |
| qcom,sde-intf-off = <0x0006b000 0x0006b800 |
| 0x0006c000 0x0006c800>; |
| qcom,sde-intf-type = "none", "dsi", "dsi", "hdmi"; |
| qcom,sde-pp-off = <0x00071000 0x00071800 |
| 0x00072000 0x00072800>; |
| qcom,sde-pp-slave = <0x0 0x0 0x0 0x0>; |
| qcom,sde-cdm-off = <0x0007a200>; |
| qcom,sde-dsc-off = <0x00081000 0x00081400>; |
| qcom,sde-intf-max-prefetch-lines = <0x15 0x15 0x15 0x15>; |
| |
| qcom,sde-mixer-pair-mask = <2 1 6 0 0 3>; |
| qcom,sde-mixer-blend-op-off = <0x20 0x38 0x50 0x68 0x80 0x98 |
| 0xb0 0xc8 0xe0 0xf8 0x110>; |
| |
| |
| qcom,sde-sspp-type = "vig", "vig", "vig", |
| "vig", "rgb", "rgb", |
| "rgb", "rgb", "dma", |
| "dma", "cursor", "cursor"; |
| |
| qcom,sde-sspp-off = <0x00005000 0x00007000 0x00009000 |
| 0x0000b000 0x00015000 0x00017000 |
| 0x00019000 0x0001b000 0x00025000 |
| 0x00027000 0x00035000 0x00037000>; |
| |
| qcom,sde-sspp-xin-id = <0 4 8 |
| 12 1 5 |
| 9 13 2 |
| 10 7 7>; |
| |
| /* offsets are relative to "mdp_phys + qcom,sde-off */ |
| qcom,sde-sspp-clk-ctrl = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>, |
| <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>, |
| <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>, |
| <0x3b0 16>; |
| qcom,sde-sspp-clk-status = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>, |
| <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>, |
| <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>, |
| <0x3b0 16>; |
| qcom,sde-mixer-linewidth = <2560>; |
| qcom,sde-sspp-linewidth = <2560>; |
| qcom,sde-mixer-blendstages = <0x7>; |
| qcom,sde-highest-bank-bit = <0x2>; |
| qcom,sde-ubwc-version = <0x100>; |
| qcom,sde-ubwc-static = <0x100>; |
| qcom,sde-ubwc-swizzle = <0>; |
| qcom,sde-panic-per-pipe; |
| qcom,sde-has-src-split; |
| qcom,sde-has-dim-layer; |
| qcom,sde-sspp-src-size = <0x100>; |
| qcom,sde-mixer-size = <0x100>; |
| qcom,sde-ctl-size = <0x100>; |
| qcom,sde-dspp-top-size = <0xc>; |
| qcom,sde-dspp-size = <0x100>; |
| qcom,sde-intf-size = <0x100>; |
| qcom,sde-dsc-size = <0x100>; |
| qcom,sde-cdm-size = <0x100>; |
| qcom,sde-pp-size = <0x100>; |
| qcom,sde-wb-size = <0x100>; |
| qcom,sde-dest-scaler-top-size = <0xc>; |
| qcom,sde-dest-scaler-size = <0x800>; |
| qcom,sde-len = <0x100>; |
| qcom,sde-wb-linewidth = <2560>; |
| qcom,sde-sspp-scale-size = <0x100>; |
| qcom,sde-mixer-blendstages = <0x8>; |
| qcom,sde-qseed-type = "qseedv2"; |
| qcom,sde-csc-type = "csc-10bit"; |
| qcom,sde-highest-bank-bit = <15>; |
| qcom,sde-has-mixer-gc; |
| qcom,sde-has-idle-pc; |
| qcom,sde-has-dest-scaler; |
| qcom,sde-max-dest-scaler-input-linewidth = <2048>; |
| qcom,sde-max-dest-scaler-output-linewidth = <2560>; |
| qcom,sde-sspp-max-rects = <1 1 1 1 |
| 1 1 1 1 |
| 1 1 |
| 1 1>; |
| qcom,sde-sspp-excl-rect = <1 1 1 1 |
| 1 1 1 1 |
| 1 1 |
| 1 1>; |
| qcom,sde-sspp-smart-dma-priority = <0 0 0 0 |
| 0 0 0 0 |
| 0 0 |
| 1 2>; |
| qcom,sde-smart-dma-rev = "smart_dma_v2"; |
| qcom,sde-te-off = <0x100>; |
| qcom,sde-te2-off = <0x100>; |
| qcom,sde-te-size = <0xffff>; |
| qcom,sde-te2-size = <0xffff>; |
| |
| qcom,sde-wb-id = <2>; |
| qcom,sde-wb-clk-ctrl = <0x2bc 16>; |
| |
| qcom,sde-danger-lut = <0x0000000f 0x0000ffff 0x00000000 |
| 0x00000000>; |
| qcom,sde-safe-lut = <0xfffc 0xff00 0xffff 0xffff>; |
| qcom,sde-qos-lut-linear = |
| <4 0x00000000 0x00000357>, |
| <5 0x00000000 0x00003357>, |
| <6 0x00000000 0x00023357>, |
| <7 0x00000000 0x00223357>, |
| <8 0x00000000 0x02223357>, |
| <9 0x00000000 0x22223357>, |
| <10 0x00000002 0x22223357>, |
| <11 0x00000022 0x22223357>, |
| <12 0x00000222 0x22223357>, |
| <13 0x00002222 0x22223357>, |
| <14 0x00012222 0x22223357>, |
| <0 0x00112222 0x22223357>; |
| qcom,sde-qos-lut-macrotile = |
| <10 0x00000003 0x44556677>, |
| <11 0x00000033 0x44556677>, |
| <12 0x00000233 0x44556677>, |
| <13 0x00002233 0x44556677>, |
| <14 0x00012233 0x44556677>, |
| <0 0x00112233 0x44556677>; |
| qcom,sde-qos-lut-nrt = |
| <0 0x00000000 0x00000000>; |
| qcom,sde-qos-lut-cwb = |
| <0 0x75300000 0x00000000>; |
| |
| qcom,sde-cdp-setting = <1 1>, <1 0>; |
| |
| qcom,sde-qos-cpu-mask = <0x3>; |
| qcom,sde-qos-cpu-dma-latency = <300>; |
| |
| qcom,sde-vbif-off = <0 0>; |
| qcom,sde-vbif-id = <0 1>; |
| qcom,sde-vbif-default-ot-rd-limit = <32>; |
| qcom,sde-vbif-default-ot-wr-limit = <16>; |
| qcom,sde-vbif-dynamic-ot-rd-limit = <62208000 2>, |
| <124416000 4>, <248832000 16>; |
| qcom,sde-vbif-dynamic-ot-wr-limit = <62208000 2>, |
| <124416000 4>, <248832000 16>; |
| qcom,sde-vbif-memtype-0 = <3 3 3 3 3 3 3 3>; |
| qcom,sde-vbif-memtype-1 = <3 3 3 3 3 3>; |
| |
| qcom,sde-dram-channels = <2>; |
| qcom,sde-num-nrt-paths = <1>; |
| |
| qcom,sde-max-bw-high-kbps = <9000000>; |
| qcom,sde-max-bw-low-kbps = <9000000>; |
| |
| qcom,sde-core-ib-ff = "1.1"; |
| qcom,sde-core-clk-ff = "1.0"; |
| qcom,sde-min-core-ib-kbps = <2400000>; |
| qcom,sde-min-llcc-ib-kbps = <800000>; |
| qcom,sde-min-dram-ib-kbps = <800000>; |
| qcom,sde-comp-ratio-rt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3"; |
| qcom,sde-comp-ratio-nrt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3"; |
| qcom,sde-undersized-prefill-lines = <4>; |
| qcom,sde-xtra-prefill-lines = <5>; |
| qcom,sde-dest-scale-prefill-lines = <6>; |
| qcom,sde-macrotile-prefill-lines = <7>; |
| qcom,sde-yuv-nv12-prefill-lines = <8>; |
| qcom,sde-linear-prefill-lines = <9>; |
| qcom,sde-downscaling-prefill-lines = <10>; |
| qcom,sde-max-per-pipe-bw-kbps = <2400000 2400000 2400000 2400000 |
| 2400000 2400000 2400000 2400000>; |
| qcom,sde-amortizable-threshold = <11>; |
| |
| qcom,sde-vbif-qos-rt-remap = <3 3 4 4 5 5 6 6>; |
| qcom,sde-vbif-qos-nrt-remap = <3 3 3 3 3 3 3 3>; |
| |
| qcom,sde-sspp-vig-blocks { |
| qcom,sde-vig-csc-off = <0x320>; |
| qcom,sde-vig-qseed-off = <0x200>; |
| qcom,sde-vig-qseed-size = <0x74>; |
| /* Offset from vig top, version of HSIC */ |
| qcom,sde-vig-hsic = <0x200 0x00010000>; |
| qcom,sde-vig-memcolor = <0x200 0x00010000>; |
| qcom,sde-vig-pcc = <0x1780 0x00010000>; |
| }; |
| |
| qcom,sde-sspp-rgb-blocks { |
| qcom,sde-rgb-scaler-off = <0x200>; |
| qcom,sde-rgb-scaler-size = <0x74>; |
| qcom,sde-rgb-pcc = <0x380 0x00010000>; |
| }; |
| |
| qcom,sde-dspp-blocks { |
| qcom,sde-dspp-igc = <0x0 0x00010000>; |
| qcom,sde-dspp-pcc = <0x1700 0x00010000>; |
| qcom,sde-dspp-gc = <0x17c0 0x00010000>; |
| qcom,sde-dspp-hsic = <0x0 0x00010000>; |
| qcom,sde-dspp-memcolor = <0x0 0x00010000>; |
| qcom,sde-dspp-sixzone = <0x0 0x00010000>; |
| qcom,sde-dspp-gamut = <0x1600 0x00010000>; |
| qcom,sde-dspp-dither = <0x0 0x00010000>; |
| qcom,sde-dspp-hist = <0x0 0x00010000>; |
| qcom,sde-dspp-vlut = <0x0 0x00010000>; |
| }; |
| |
| qcom,sde-mixer-blocks { |
| qcom,sde-mixer-gc = <0x3c0 0x00010000>; |
| }; |
| |
| qcom,msm-hdmi-audio-rx { |
| compatible = "qcom,msm-hdmi-audio-codec-rx"; |
| }; |
| |
| qcom,sde-inline-rotator = <&mdss_rotator 0>; |
| qcom,sde-inline-rot-xin = <10 11>; |
| qcom,sde-inline-rot-xin-type = "sspp", "wb"; |
| qcom,sde-inline-rot-clk-ctrl = <0x2bc 0x8>, <0x2bc 0xc>; |
| |
| qcom,platform-supply-entries { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| qcom,platform-supply-entry@0 { |
| reg = <0>; |
| qcom,supply-name = "vdd"; |
| qcom,supply-min-voltage = <0>; |
| qcom,supply-max-voltage = <0>; |
| qcom,supply-enable-load = <0>; |
| qcom,supply-disable-load = <0>; |
| qcom,supply-pre-on-sleep = <0>; |
| qcom,supply-post-on-sleep = <0>; |
| qcom,supply-pre-off-sleep = <0>; |
| qcom,supply-post-off-sleep = <0>; |
| }; |
| }; |
| |
| qcom,sde-data-bus { |
| qcom,msm-bus,name = "mdss_sde"; |
| qcom,msm-bus,num-cases = <3>; |
| qcom,msm-bus,num-paths = <3>; |
| qcom,msm-bus,vectors-KBps = |
| <22 512 0 0>, <23 512 0 0>, <25 512 0 0>, |
| <22 512 0 6400000>, <23 512 0 6400000>, |
| <25 512 0 6400000>, |
| <22 512 0 6400000>, <23 512 0 6400000>, |
| <25 512 0 6400000>; |
| }; |
| qcom,sde-llcc-bus { |
| qcom,msm-bus,name = "mdss_sde_llcc"; |
| qcom,msm-bus,num-cases = <3>; |
| qcom,msm-bus,num-paths = <1>; |
| qcom,msm-bus,vectors-KBps = |
| <132 770 0 0>, |
| <132 770 0 6400000>, |
| <132 770 0 6400000>; |
| }; |
| qcom,sde-ebi-bus { |
| qcom,msm-bus,name = "mdss_sde_ebi"; |
| qcom,msm-bus,num-cases = <3>; |
| qcom,msm-bus,num-paths = <1>; |
| qcom,msm-bus,vectors-KBps = |
| <129 512 0 0>, |
| <129 512 0 6400000>, |
| <129 512 0 6400000>; |
| }; |
| |
| qcom,sde-reg-bus { |
| /* Reg Bus Scale Settings */ |
| qcom,msm-bus,name = "mdss_reg"; |
| qcom,msm-bus,num-cases = <4>; |
| qcom,msm-bus,num-paths = <1>; |
| qcom,msm-bus,active-only; |
| qcom,msm-bus,vectors-KBps = |
| <1 590 0 0>, |
| <1 590 0 76800>, |
| <1 590 0 160000>, |
| <1 590 0 320000>; |
| }; |
| |
| smmu_kms_unsec: qcom,smmu_kms_unsec_cb { |
| compatible = "qcom,smmu_sde_unsec"; |
| iommus = <&mmss_smmu 0>; |
| }; |
| |
| smmu_kms_sec: qcom,smmu_kms_sec_cb { |
| compatible = "qcom,smmu_sde_sec"; |
| iommus = <&mmss_smmu 1>; |
| }; |
| }; |