diff --git a/arch/arm/mach-exynos4/setup-sdhci.c b/arch/arm/mach-exynos4/setup-sdhci.c
index 1e83f8c..92937b4 100644
--- a/arch/arm/mach-exynos4/setup-sdhci.c
+++ b/arch/arm/mach-exynos4/setup-sdhci.c
@@ -10,16 +10,7 @@
  * published by the Free Software Foundation.
 */
 
-#include <linux/kernel.h>
 #include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <linux/mmc/card.h>
-#include <linux/mmc/host.h>
-
-#include <plat/regs-sdhci.h>
 
 /* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
 
@@ -29,41 +20,3 @@
 	[2] = "sclk_mmc",	/* mmc_bus */
 	[3] = NULL,
 };
-
-void exynos4_setup_sdhci_cfg_card(struct platform_device *dev, void __iomem *r,
-				  struct mmc_ios *ios, struct mmc_card *card)
-{
-	u32 ctrl2, ctrl3;
-
-	/* don't need to alter anything according to card-type */
-
-	ctrl2 = readl(r + S3C_SDHCI_CONTROL2);
-
-	/* select base clock source to HCLK */
-
-	ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
-
-	/*
-	 * clear async mode, enable conflict mask, rx feedback ctrl, SD
-	 * clk hold and no use debounce count
-	 */
-
-	ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
-		  S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
-		  S3C_SDHCI_CTRL2_ENFBCLKRX |
-		  S3C_SDHCI_CTRL2_DFCNT_NONE |
-		  S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
-
-	/* Tx and Rx feedback clock delay control */
-
-	if (ios->clock < 25 * 1000000)
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
-			 S3C_SDHCI_CTRL3_FCSEL2 |
-			 S3C_SDHCI_CTRL3_FCSEL1 |
-			 S3C_SDHCI_CTRL3_FCSEL0);
-	else
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
-
-	writel(ctrl2, r + S3C_SDHCI_CONTROL2);
-	writel(ctrl3, r + S3C_SDHCI_CONTROL3);
-}
diff --git a/arch/arm/mach-s3c2416/setup-sdhci.c b/arch/arm/mach-s3c2416/setup-sdhci.c
index ed34fad..cee5395 100644
--- a/arch/arm/mach-s3c2416/setup-sdhci.c
+++ b/arch/arm/mach-s3c2416/setup-sdhci.c
@@ -12,17 +12,7 @@
  * published by the Free Software Foundation.
 */
 
-#include <linux/kernel.h>
 #include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <linux/mmc/card.h>
-#include <linux/mmc/host.h>
-
-#include <plat/regs-sdhci.h>
-#include <plat/sdhci.h>
 
 /* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
 
@@ -32,30 +22,3 @@
 	[2] = "hsmmc-if",
 	/* [3] = "48m", - note not successfully used yet */
 };
-
-void s3c2416_setup_sdhci_cfg_card(struct platform_device *dev,
-				  void __iomem *r,
-				  struct mmc_ios *ios,
-				  struct mmc_card *card)
-{
-	u32 ctrl2, ctrl3;
-
-	ctrl2 = __raw_readl(r + S3C_SDHCI_CONTROL2);
-	ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
-	ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
-		  S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
-		  S3C_SDHCI_CTRL2_ENFBCLKRX |
-		  S3C_SDHCI_CTRL2_DFCNT_NONE |
-		  S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
-
-	if (ios->clock < 25 * 1000000)
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
-			 S3C_SDHCI_CTRL3_FCSEL2 |
-			 S3C_SDHCI_CTRL3_FCSEL1 |
-			 S3C_SDHCI_CTRL3_FCSEL0);
-	else
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
-
-	__raw_writel(ctrl2, r + S3C_SDHCI_CONTROL2);
-	__raw_writel(ctrl3, r + S3C_SDHCI_CONTROL3);
-}
diff --git a/arch/arm/mach-s3c64xx/setup-sdhci.c b/arch/arm/mach-s3c64xx/setup-sdhci.c
index f344a22..c75a71b 100644
--- a/arch/arm/mach-s3c64xx/setup-sdhci.c
+++ b/arch/arm/mach-s3c64xx/setup-sdhci.c
@@ -12,17 +12,7 @@
  * published by the Free Software Foundation.
 */
 
-#include <linux/kernel.h>
 #include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <linux/mmc/card.h>
-#include <linux/mmc/host.h>
-
-#include <plat/regs-sdhci.h>
-#include <plat/sdhci.h>
 
 /* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
 
@@ -32,41 +22,3 @@
 	[2] = "mmc_bus",
 	/* [3] = "48m", - note not successfully used yet */
 };
-
-void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev,
-				  void __iomem *r,
-				  struct mmc_ios *ios,
-				  struct mmc_card *card)
-{
-	u32 ctrl2, ctrl3;
-
-	ctrl2 = readl(r + S3C_SDHCI_CONTROL2);
-	ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
-	ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
-		  S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
-		  S3C_SDHCI_CTRL2_ENFBCLKRX |
-		  S3C_SDHCI_CTRL2_DFCNT_NONE |
-		  S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
-
-	if (ios->clock < 25 * 1000000)
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
-			 S3C_SDHCI_CTRL3_FCSEL2 |
-			 S3C_SDHCI_CTRL3_FCSEL1 |
-			 S3C_SDHCI_CTRL3_FCSEL0);
-	else
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
-
-	pr_debug("%s: CTRL 2=%08x, 3=%08x\n", __func__, ctrl2, ctrl3);
-	writel(ctrl2, r + S3C_SDHCI_CONTROL2);
-	writel(ctrl3, r + S3C_SDHCI_CONTROL3);
-}
-
-void s3c6410_setup_sdhci_cfg_card(struct platform_device *dev,
-				  void __iomem *r,
-				  struct mmc_ios *ios,
-				  struct mmc_card *card)
-{
-	writel(S3C64XX_SDHCI_CONTROL4_DRIVE_9mA, r + S3C64XX_SDHCI_CONTROL4);
-
-	s3c6400_setup_sdhci_cfg_card(dev, r, ios, card);
-}
diff --git a/arch/arm/mach-s5pc100/setup-sdhci.c b/arch/arm/mach-s5pc100/setup-sdhci.c
index be25879..6418c6e 100644
--- a/arch/arm/mach-s5pc100/setup-sdhci.c
+++ b/arch/arm/mach-s5pc100/setup-sdhci.c
@@ -11,17 +11,7 @@
  * published by the Free Software Foundation.
 */
 
-#include <linux/kernel.h>
 #include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <linux/mmc/card.h>
-#include <linux/mmc/host.h>
-
-#include <plat/regs-sdhci.h>
-#include <plat/sdhci.h>
 
 /* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
 
@@ -31,35 +21,3 @@
 	[2] = "sclk_mmc",	/* mmc_bus */
 	/* [3] = "48m",		- note not successfully used yet */
 };
-
-
-void s5pc100_setup_sdhci0_cfg_card(struct platform_device *dev,
-				    void __iomem *r,
-				    struct mmc_ios *ios,
-				    struct mmc_card *card)
-{
-	u32 ctrl2, ctrl3;
-
-	/* don't need to alter anything according to card-type */
-
-	writel(S3C64XX_SDHCI_CONTROL4_DRIVE_9mA, r + S3C64XX_SDHCI_CONTROL4);
-
-	ctrl2 = readl(r + S3C_SDHCI_CONTROL2);
-	ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
-	ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
-		  S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
-		  S3C_SDHCI_CTRL2_ENFBCLKRX |
-		  S3C_SDHCI_CTRL2_DFCNT_NONE |
-		  S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
-
-	if (ios->clock < 25 * 1000000)
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
-			 S3C_SDHCI_CTRL3_FCSEL2 |
-			 S3C_SDHCI_CTRL3_FCSEL1 |
-			 S3C_SDHCI_CTRL3_FCSEL0);
-	else
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
-
-	writel(ctrl2, r + S3C_SDHCI_CONTROL2);
-	writel(ctrl3, r + S3C_SDHCI_CONTROL3);
-}
diff --git a/arch/arm/mach-s5pv210/setup-sdhci.c b/arch/arm/mach-s5pv210/setup-sdhci.c
index a83b6c9..6b8ccc4 100644
--- a/arch/arm/mach-s5pv210/setup-sdhci.c
+++ b/arch/arm/mach-s5pv210/setup-sdhci.c
@@ -10,17 +10,7 @@
  * published by the Free Software Foundation.
 */
 
-#include <linux/kernel.h>
 #include <linux/types.h>
-#include <linux/interrupt.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <linux/mmc/card.h>
-#include <linux/mmc/host.h>
-
-#include <plat/regs-sdhci.h>
-#include <plat/sdhci.h>
 
 /* clock sources for the mmc bus clock, order as for the ctrl2[5..4] */
 
@@ -30,34 +20,3 @@
 	[2] = "sclk_mmc",	/* mmc_bus */
 	/* [3] = NULL,		- reserved */
 };
-
-void s5pv210_setup_sdhci_cfg_card(struct platform_device *dev,
-				    void __iomem *r,
-				    struct mmc_ios *ios,
-				    struct mmc_card *card)
-{
-	u32 ctrl2, ctrl3;
-
-	/* don't need to alter anything according to card-type */
-
-	writel(S3C64XX_SDHCI_CONTROL4_DRIVE_9mA, r + S3C64XX_SDHCI_CONTROL4);
-
-	ctrl2 = readl(r + S3C_SDHCI_CONTROL2);
-	ctrl2 &= S3C_SDHCI_CTRL2_SELBASECLK_MASK;
-	ctrl2 |= (S3C64XX_SDHCI_CTRL2_ENSTAASYNCCLR |
-		  S3C64XX_SDHCI_CTRL2_ENCMDCNFMSK |
-		  S3C_SDHCI_CTRL2_ENFBCLKRX |
-		  S3C_SDHCI_CTRL2_DFCNT_NONE |
-		  S3C_SDHCI_CTRL2_ENCLKOUTHOLD);
-
-	if (ios->clock < 25 * 1000000)
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL3 |
-			 S3C_SDHCI_CTRL3_FCSEL2 |
-			 S3C_SDHCI_CTRL3_FCSEL1 |
-			 S3C_SDHCI_CTRL3_FCSEL0);
-	else
-		ctrl3 = (S3C_SDHCI_CTRL3_FCSEL1 | S3C_SDHCI_CTRL3_FCSEL0);
-
-	writel(ctrl2, r + S3C_SDHCI_CONTROL2);
-	writel(ctrl3, r + S3C_SDHCI_CONTROL3);
-}
diff --git a/arch/arm/plat-samsung/include/plat/sdhci.h b/arch/arm/plat-samsung/include/plat/sdhci.h
index 4a65520..e7b3c75 100644
--- a/arch/arm/plat-samsung/include/plat/sdhci.h
+++ b/arch/arm/plat-samsung/include/plat/sdhci.h
@@ -55,10 +55,6 @@
  *		 cd_type == S3C_SDHCI_CD_GPIO
  * @ext_cd_gpio_invert: invert values for external CD gpio line
  * @cfg_gpio: Configure the GPIO for a specific card bit-width
- * @cfg_card: Configure the interface for a specific card and speed. This
- *            is necessary the controllers and/or GPIO blocks require the
- *	      changing of driver-strength and other controls dependent on
- *	      the card and speed of operation.
  *
  * Initialisation data specific to either the machine or the platform
  * for the device driver to use or call-back when configuring gpio or
@@ -80,10 +76,6 @@
 						      int state));
 
 	void	(*cfg_gpio)(struct platform_device *dev, int width);
-	void	(*cfg_card)(struct platform_device *dev,
-			    void __iomem *regbase,
-			    struct mmc_ios *ios,
-			    struct mmc_card *card);
 };
 
 /* s3c_sdhci_set_platdata() - common helper for setting SDHCI platform data
@@ -139,17 +131,11 @@
 #ifdef CONFIG_S3C2416_SETUP_SDHCI
 extern char *s3c2416_hsmmc_clksrcs[4];
 
-extern void s3c2416_setup_sdhci_cfg_card(struct platform_device *dev,
-					   void __iomem *r,
-					   struct mmc_ios *ios,
-					   struct mmc_card *card);
-
 static inline void s3c2416_default_sdhci0(void)
 {
 #ifdef CONFIG_S3C_DEV_HSMMC
 	s3c_hsmmc0_def_platdata.clocks = s3c2416_hsmmc_clksrcs;
 	s3c_hsmmc0_def_platdata.cfg_gpio = s3c2416_setup_sdhci0_cfg_gpio;
-	s3c_hsmmc0_def_platdata.cfg_card = s3c2416_setup_sdhci_cfg_card;
 #endif /* CONFIG_S3C_DEV_HSMMC */
 }
 
@@ -158,7 +144,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC1
 	s3c_hsmmc1_def_platdata.clocks = s3c2416_hsmmc_clksrcs;
 	s3c_hsmmc1_def_platdata.cfg_gpio = s3c2416_setup_sdhci1_cfg_gpio;
-	s3c_hsmmc1_def_platdata.cfg_card = s3c2416_setup_sdhci_cfg_card;
 #endif /* CONFIG_S3C_DEV_HSMMC1 */
 }
 
@@ -172,17 +157,11 @@
 #ifdef CONFIG_S3C64XX_SETUP_SDHCI
 extern char *s3c64xx_hsmmc_clksrcs[4];
 
-extern void s3c6400_setup_sdhci_cfg_card(struct platform_device *dev,
-					 void __iomem *r,
-					 struct mmc_ios *ios,
-					 struct mmc_card *card);
-
 static inline void s3c6400_default_sdhci0(void)
 {
 #ifdef CONFIG_S3C_DEV_HSMMC
 	s3c_hsmmc0_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
 	s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
-	s3c_hsmmc0_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -191,7 +170,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC1
 	s3c_hsmmc1_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
 	s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
-	s3c_hsmmc1_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -200,21 +178,14 @@
 #ifdef CONFIG_S3C_DEV_HSMMC2
 	s3c_hsmmc2_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
 	s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio;
-	s3c_hsmmc2_def_platdata.cfg_card = s3c6400_setup_sdhci_cfg_card;
 #endif
 }
 
-extern void s3c6410_setup_sdhci_cfg_card(struct platform_device *dev,
-					 void __iomem *r,
-					 struct mmc_ios *ios,
-					 struct mmc_card *card);
-
 static inline void s3c6410_default_sdhci0(void)
 {
 #ifdef CONFIG_S3C_DEV_HSMMC
 	s3c_hsmmc0_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
 	s3c_hsmmc0_def_platdata.cfg_gpio = s3c64xx_setup_sdhci0_cfg_gpio;
-	s3c_hsmmc0_def_platdata.cfg_card = s3c6410_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -223,7 +194,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC1
 	s3c_hsmmc1_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
 	s3c_hsmmc1_def_platdata.cfg_gpio = s3c64xx_setup_sdhci1_cfg_gpio;
-	s3c_hsmmc1_def_platdata.cfg_card = s3c6410_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -232,7 +202,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC2
 	s3c_hsmmc2_def_platdata.clocks = s3c64xx_hsmmc_clksrcs;
 	s3c_hsmmc2_def_platdata.cfg_gpio = s3c64xx_setup_sdhci2_cfg_gpio;
-	s3c_hsmmc2_def_platdata.cfg_card = s3c6410_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -251,17 +220,11 @@
 #ifdef CONFIG_S5PC100_SETUP_SDHCI
 extern char *s5pc100_hsmmc_clksrcs[4];
 
-extern void s5pc100_setup_sdhci0_cfg_card(struct platform_device *dev,
-					   void __iomem *r,
-					   struct mmc_ios *ios,
-					   struct mmc_card *card);
-
 static inline void s5pc100_default_sdhci0(void)
 {
 #ifdef CONFIG_S3C_DEV_HSMMC
 	s3c_hsmmc0_def_platdata.clocks = s5pc100_hsmmc_clksrcs;
 	s3c_hsmmc0_def_platdata.cfg_gpio = s5pc100_setup_sdhci0_cfg_gpio;
-	s3c_hsmmc0_def_platdata.cfg_card = s5pc100_setup_sdhci0_cfg_card;
 #endif
 }
 
@@ -270,7 +233,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC1
 	s3c_hsmmc1_def_platdata.clocks = s5pc100_hsmmc_clksrcs;
 	s3c_hsmmc1_def_platdata.cfg_gpio = s5pc100_setup_sdhci1_cfg_gpio;
-	s3c_hsmmc1_def_platdata.cfg_card = s5pc100_setup_sdhci0_cfg_card;
 #endif
 }
 
@@ -279,7 +241,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC2
 	s3c_hsmmc2_def_platdata.clocks = s5pc100_hsmmc_clksrcs;
 	s3c_hsmmc2_def_platdata.cfg_gpio = s5pc100_setup_sdhci2_cfg_gpio;
-	s3c_hsmmc2_def_platdata.cfg_card = s5pc100_setup_sdhci0_cfg_card;
 #endif
 }
 
@@ -295,17 +256,11 @@
 #ifdef CONFIG_S5PV210_SETUP_SDHCI
 extern char *s5pv210_hsmmc_clksrcs[4];
 
-extern void s5pv210_setup_sdhci_cfg_card(struct platform_device *dev,
-					   void __iomem *r,
-					   struct mmc_ios *ios,
-					   struct mmc_card *card);
-
 static inline void s5pv210_default_sdhci0(void)
 {
 #ifdef CONFIG_S3C_DEV_HSMMC
 	s3c_hsmmc0_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
 	s3c_hsmmc0_def_platdata.cfg_gpio = s5pv210_setup_sdhci0_cfg_gpio;
-	s3c_hsmmc0_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -314,7 +269,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC1
 	s3c_hsmmc1_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
 	s3c_hsmmc1_def_platdata.cfg_gpio = s5pv210_setup_sdhci1_cfg_gpio;
-	s3c_hsmmc1_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -323,7 +277,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC2
 	s3c_hsmmc2_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
 	s3c_hsmmc2_def_platdata.cfg_gpio = s5pv210_setup_sdhci2_cfg_gpio;
-	s3c_hsmmc2_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -332,7 +285,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC3
 	s3c_hsmmc3_def_platdata.clocks = s5pv210_hsmmc_clksrcs;
 	s3c_hsmmc3_def_platdata.cfg_gpio = s5pv210_setup_sdhci3_cfg_gpio;
-	s3c_hsmmc3_def_platdata.cfg_card = s5pv210_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -348,17 +300,11 @@
 #ifdef CONFIG_EXYNOS4_SETUP_SDHCI
 extern char *exynos4_hsmmc_clksrcs[4];
 
-extern void exynos4_setup_sdhci_cfg_card(struct platform_device *dev,
-					   void __iomem *r,
-					   struct mmc_ios *ios,
-					   struct mmc_card *card);
-
 static inline void exynos4_default_sdhci0(void)
 {
 #ifdef CONFIG_S3C_DEV_HSMMC
 	s3c_hsmmc0_def_platdata.clocks = exynos4_hsmmc_clksrcs;
 	s3c_hsmmc0_def_platdata.cfg_gpio = exynos4_setup_sdhci0_cfg_gpio;
-	s3c_hsmmc0_def_platdata.cfg_card = exynos4_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -367,7 +313,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC1
 	s3c_hsmmc1_def_platdata.clocks = exynos4_hsmmc_clksrcs;
 	s3c_hsmmc1_def_platdata.cfg_gpio = exynos4_setup_sdhci1_cfg_gpio;
-	s3c_hsmmc1_def_platdata.cfg_card = exynos4_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -376,7 +321,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC2
 	s3c_hsmmc2_def_platdata.clocks = exynos4_hsmmc_clksrcs;
 	s3c_hsmmc2_def_platdata.cfg_gpio = exynos4_setup_sdhci2_cfg_gpio;
-	s3c_hsmmc2_def_platdata.cfg_card = exynos4_setup_sdhci_cfg_card;
 #endif
 }
 
@@ -385,7 +329,6 @@
 #ifdef CONFIG_S3C_DEV_HSMMC3
 	s3c_hsmmc3_def_platdata.clocks = exynos4_hsmmc_clksrcs;
 	s3c_hsmmc3_def_platdata.cfg_gpio = exynos4_setup_sdhci3_cfg_gpio;
-	s3c_hsmmc3_def_platdata.cfg_card = exynos4_setup_sdhci_cfg_card;
 #endif
 }
 
diff --git a/arch/arm/plat-samsung/platformdata.c b/arch/arm/plat-samsung/platformdata.c
index 6de1a38..4c9a207 100644
--- a/arch/arm/plat-samsung/platformdata.c
+++ b/arch/arm/plat-samsung/platformdata.c
@@ -50,8 +50,6 @@
 		set->max_width = pd->max_width;
 	if (pd->cfg_gpio)
 		set->cfg_gpio = pd->cfg_gpio;
-	if (pd->cfg_card)
-		set->cfg_card = pd->cfg_card;
 	if (pd->host_caps)
 		set->host_caps |= pd->host_caps;
 	if (pd->clk_type)