pcmcia: do not use io_req_t when calling pcmcia_request_io()
Instead of io_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[0,1] for up to two ioport
ranges. After a call to pcmcia_request_io(), the ports found there
are reserved, after calling pcmcia_request_configuration(), they may
be used.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
diff --git a/drivers/isdn/hisax/sedlbauer_cs.c b/drivers/isdn/hisax/sedlbauer_cs.c
index cecb35a..4755eb4 100644
--- a/drivers/isdn/hisax/sedlbauer_cs.c
+++ b/drivers/isdn/hisax/sedlbauer_cs.c
@@ -129,9 +129,8 @@
/* from old sedl_cs
*/
/* The io structure describes IO port mapping */
- link->io.NumPorts1 = 8;
- link->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- link->io.IOAddrLines = 3;
+ link->resource[0]->end = 8;
+ link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8;
link->conf.Attributes = 0;
link->conf.IntType = INT_MEMORY_AND_IO;
@@ -201,23 +200,22 @@
p_dev->conf.Attributes |= CONF_ENABLE_IRQ;
/* IO window settings */
- p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0;
+ p_dev->resource[0]->end = p_dev->resource[1]->end = 0;
if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) {
cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io;
- p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO;
- if (!(io->flags & CISTPL_IO_8BIT))
- p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16;
- if (!(io->flags & CISTPL_IO_16BIT))
- p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8;
- p_dev->io.BasePort1 = io->win[0].base;
- p_dev->io.NumPorts1 = io->win[0].len;
+ p_dev->resource[0]->start = io->win[0].base;
+ p_dev->resource[0]->end = io->win[0].len;
+ p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
+ p_dev->resource[0]->flags |=
+ pcmcia_io_cfg_data_width(io->flags);
if (io->nwin > 1) {
- p_dev->io.Attributes2 = p_dev->io.Attributes1;
- p_dev->io.BasePort2 = io->win[1].base;
- p_dev->io.NumPorts2 = io->win[1].len;
+ p_dev->resource[1]->flags = p_dev->resource[0]->flags;
+ p_dev->resource[1]->start = io->win[1].base;
+ p_dev->resource[1]->end = io->win[1].len;
}
/* This reserves IO space but doesn't actually enable it */
- if (pcmcia_request_io(p_dev, &p_dev->io) != 0)
+ p_dev->io_lines = 3;
+ if (pcmcia_request_io(p_dev) != 0)
return -ENODEV;
}