[SCSI] mpt2sas: New feature - Fast Load Support
New feature Fast Load Support.
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c
index 81209ca..beda04a 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.c
@@ -81,6 +81,15 @@
module_param_array(missing_delay, int, NULL, 0);
MODULE_PARM_DESC(missing_delay, " device missing delay , io missing delay");
+static int mpt2sas_fwfault_debug;
+MODULE_PARM_DESC(mpt2sas_fwfault_debug, " enable detection of firmware fault "
+ "and halt firmware - (default=0)");
+
+static int disable_discovery = -1;
+module_param(disable_discovery, int, 0);
+MODULE_PARM_DESC(disable_discovery, " disable discovery ");
+
+
/* diag_buffer_enable is bitwise
* bit 0 set = TRACE
* bit 1 set = SNAPSHOT
@@ -93,14 +102,6 @@
MODULE_PARM_DESC(diag_buffer_enable, " post diag buffers "
"(TRACE=1/SNAPSHOT=2/EXTENDED=4/default=0)");
-static int mpt2sas_fwfault_debug;
-MODULE_PARM_DESC(mpt2sas_fwfault_debug, " enable detection of firmware fault "
- "and halt firmware - (default=0)");
-
-static int disable_discovery = -1;
-module_param(disable_discovery, int, 0);
-MODULE_PARM_DESC(disable_discovery, " disable discovery ");
-
/**
* _scsih_set_fwfault_debug - global setting of ioc->fwfault_debug.
*
@@ -691,6 +692,7 @@
memcpy(ioc->base_cmds.reply, mpi_reply, mpi_reply->MsgLength*4);
}
ioc->base_cmds.status &= ~MPT2_CMD_PENDING;
+
complete(&ioc->base_cmds.done);
return 1;
}
@@ -3470,6 +3472,58 @@
}
/**
+ * mpt2sas_port_enable_done - command completion routine for port enable
+ * @ioc: per adapter object
+ * @smid: system request message index
+ * @msix_index: MSIX table index supplied by the OS
+ * @reply: reply message frame(lower 32bit addr)
+ *
+ * Return 1 meaning mf should be freed from _base_interrupt
+ * 0 means the mf is freed from this function.
+ */
+u8
+mpt2sas_port_enable_done(struct MPT2SAS_ADAPTER *ioc, u16 smid, u8 msix_index,
+ u32 reply)
+{
+ MPI2DefaultReply_t *mpi_reply;
+ u16 ioc_status;
+
+ mpi_reply = mpt2sas_base_get_reply_virt_addr(ioc, reply);
+ if (mpi_reply && mpi_reply->Function == MPI2_FUNCTION_EVENT_ACK)
+ return 1;
+
+ if (ioc->port_enable_cmds.status == MPT2_CMD_NOT_USED)
+ return 1;
+
+ ioc->port_enable_cmds.status |= MPT2_CMD_COMPLETE;
+ if (mpi_reply) {
+ ioc->port_enable_cmds.status |= MPT2_CMD_REPLY_VALID;
+ memcpy(ioc->port_enable_cmds.reply, mpi_reply,
+ mpi_reply->MsgLength*4);
+ }
+ ioc->port_enable_cmds.status &= ~MPT2_CMD_PENDING;
+
+ ioc_status = le16_to_cpu(mpi_reply->IOCStatus) & MPI2_IOCSTATUS_MASK;
+
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS)
+ ioc->port_enable_failed = 1;
+
+ if (ioc->is_driver_loading) {
+ if (ioc_status == MPI2_IOCSTATUS_SUCCESS) {
+ mpt2sas_port_enable_complete(ioc);
+ return 1;
+ } else {
+ ioc->start_scan_failed = ioc_status;
+ ioc->start_scan = 0;
+ return 1;
+ }
+ }
+ complete(&ioc->port_enable_cmds.done);
+ return 1;
+}
+
+
+/**
* _base_send_port_enable - send port_enable(discovery stuff) to firmware
* @ioc: per adapter object
* @sleep_flag: CAN_SLEEP or NO_SLEEP
@@ -3480,67 +3534,151 @@
_base_send_port_enable(struct MPT2SAS_ADAPTER *ioc, int sleep_flag)
{
Mpi2PortEnableRequest_t *mpi_request;
- u32 ioc_state;
+ Mpi2PortEnableReply_t *mpi_reply;
unsigned long timeleft;
int r = 0;
u16 smid;
+ u16 ioc_status;
printk(MPT2SAS_INFO_FMT "sending port enable !!\n", ioc->name);
- if (ioc->base_cmds.status & MPT2_CMD_PENDING) {
+ if (ioc->port_enable_cmds.status & MPT2_CMD_PENDING) {
printk(MPT2SAS_ERR_FMT "%s: internal command already in use\n",
ioc->name, __func__);
return -EAGAIN;
}
- smid = mpt2sas_base_get_smid(ioc, ioc->base_cb_idx);
+ smid = mpt2sas_base_get_smid(ioc, ioc->port_enable_cb_idx);
if (!smid) {
printk(MPT2SAS_ERR_FMT "%s: failed obtaining a smid\n",
ioc->name, __func__);
return -EAGAIN;
}
- ioc->base_cmds.status = MPT2_CMD_PENDING;
+ ioc->port_enable_cmds.status = MPT2_CMD_PENDING;
mpi_request = mpt2sas_base_get_msg_frame(ioc, smid);
- ioc->base_cmds.smid = smid;
+ ioc->port_enable_cmds.smid = smid;
memset(mpi_request, 0, sizeof(Mpi2PortEnableRequest_t));
mpi_request->Function = MPI2_FUNCTION_PORT_ENABLE;
- mpi_request->VF_ID = 0; /* TODO */
- mpi_request->VP_ID = 0;
+ init_completion(&ioc->port_enable_cmds.done);
mpt2sas_base_put_smid_default(ioc, smid);
- init_completion(&ioc->base_cmds.done);
- timeleft = wait_for_completion_timeout(&ioc->base_cmds.done,
+ timeleft = wait_for_completion_timeout(&ioc->port_enable_cmds.done,
300*HZ);
- if (!(ioc->base_cmds.status & MPT2_CMD_COMPLETE)) {
+ if (!(ioc->port_enable_cmds.status & MPT2_CMD_COMPLETE)) {
printk(MPT2SAS_ERR_FMT "%s: timeout\n",
ioc->name, __func__);
_debug_dump_mf(mpi_request,
sizeof(Mpi2PortEnableRequest_t)/4);
- if (ioc->base_cmds.status & MPT2_CMD_RESET)
+ if (ioc->port_enable_cmds.status & MPT2_CMD_RESET)
r = -EFAULT;
else
r = -ETIME;
goto out;
- } else
- dinitprintk(ioc, printk(MPT2SAS_INFO_FMT "%s: complete\n",
- ioc->name, __func__));
+ }
+ mpi_reply = ioc->port_enable_cmds.reply;
- ioc_state = _base_wait_on_iocstate(ioc, MPI2_IOC_STATE_OPERATIONAL,
- 60, sleep_flag);
- if (ioc_state) {
- printk(MPT2SAS_ERR_FMT "%s: failed going to operational state "
- " (ioc_state=0x%x)\n", ioc->name, __func__, ioc_state);
+ ioc_status = le16_to_cpu(mpi_reply->IOCStatus) & MPI2_IOCSTATUS_MASK;
+ if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
+ printk(MPT2SAS_ERR_FMT "%s: failed with (ioc_status=0x%08x)\n",
+ ioc->name, __func__, ioc_status);
r = -EFAULT;
+ goto out;
}
out:
- ioc->base_cmds.status = MPT2_CMD_NOT_USED;
- printk(MPT2SAS_INFO_FMT "port enable: %s\n",
- ioc->name, ((r == 0) ? "SUCCESS" : "FAILED"));
+ ioc->port_enable_cmds.status = MPT2_CMD_NOT_USED;
+ printk(MPT2SAS_INFO_FMT "port enable: %s\n", ioc->name, ((r == 0) ?
+ "SUCCESS" : "FAILED"));
return r;
}
/**
+ * mpt2sas_port_enable - initiate firmware discovery (don't wait for reply)
+ * @ioc: per adapter object
+ *
+ * Returns 0 for success, non-zero for failure.
+ */
+int
+mpt2sas_port_enable(struct MPT2SAS_ADAPTER *ioc)
+{
+ Mpi2PortEnableRequest_t *mpi_request;
+ u16 smid;
+
+ printk(MPT2SAS_INFO_FMT "sending port enable !!\n", ioc->name);
+
+ if (ioc->port_enable_cmds.status & MPT2_CMD_PENDING) {
+ printk(MPT2SAS_ERR_FMT "%s: internal command already in use\n",
+ ioc->name, __func__);
+ return -EAGAIN;
+ }
+
+ smid = mpt2sas_base_get_smid(ioc, ioc->port_enable_cb_idx);
+ if (!smid) {
+ printk(MPT2SAS_ERR_FMT "%s: failed obtaining a smid\n",
+ ioc->name, __func__);
+ return -EAGAIN;
+ }
+
+ ioc->port_enable_cmds.status = MPT2_CMD_PENDING;
+ mpi_request = mpt2sas_base_get_msg_frame(ioc, smid);
+ ioc->port_enable_cmds.smid = smid;
+ memset(mpi_request, 0, sizeof(Mpi2PortEnableRequest_t));
+ mpi_request->Function = MPI2_FUNCTION_PORT_ENABLE;
+
+ mpt2sas_base_put_smid_default(ioc, smid);
+ return 0;
+}
+
+/**
+ * _base_determine_wait_on_discovery - desposition
+ * @ioc: per adapter object
+ *
+ * Decide whether to wait on discovery to complete. Used to either
+ * locate boot device, or report volumes ahead of physical devices.
+ *
+ * Returns 1 for wait, 0 for don't wait
+ */
+static int
+_base_determine_wait_on_discovery(struct MPT2SAS_ADAPTER *ioc)
+{
+ /* We wait for discovery to complete if IR firmware is loaded.
+ * The sas topology events arrive before PD events, so we need time to
+ * turn on the bit in ioc->pd_handles to indicate PD
+ * Also, it maybe required to report Volumes ahead of physical
+ * devices when MPI2_IOCPAGE8_IRFLAGS_LOW_VOLUME_MAPPING is set.
+ */
+ if (ioc->ir_firmware)
+ return 1;
+
+ /* if no Bios, then we don't need to wait */
+ if (!ioc->bios_pg3.BiosVersion)
+ return 0;
+
+ /* Bios is present, then we drop down here.
+ *
+ * If there any entries in the Bios Page 2, then we wait
+ * for discovery to complete.
+ */
+
+ /* Current Boot Device */
+ if ((ioc->bios_pg2.CurrentBootDeviceForm &
+ MPI2_BIOSPAGE2_FORM_MASK) ==
+ MPI2_BIOSPAGE2_FORM_NO_DEVICE_SPECIFIED &&
+ /* Request Boot Device */
+ (ioc->bios_pg2.ReqBootDeviceForm &
+ MPI2_BIOSPAGE2_FORM_MASK) ==
+ MPI2_BIOSPAGE2_FORM_NO_DEVICE_SPECIFIED &&
+ /* Alternate Request Boot Device */
+ (ioc->bios_pg2.ReqAltBootDeviceForm &
+ MPI2_BIOSPAGE2_FORM_MASK) ==
+ MPI2_BIOSPAGE2_FORM_NO_DEVICE_SPECIFIED)
+ return 0;
+
+ return 1;
+}
+
+
+/**
* _base_unmask_events - turn on notification for this event
* @ioc: per adapter object
* @event: firmware event
@@ -3962,6 +4100,7 @@
skip_init_reply_post_host_index:
_base_unmask_interrupts(ioc);
+
r = _base_event_notification(ioc, sleep_flag);
if (r)
return r;
@@ -3969,7 +4108,18 @@
if (sleep_flag == CAN_SLEEP)
_base_static_config_pages(ioc);
- if (ioc->wait_for_port_enable_to_complete && ioc->is_warpdrive) {
+
+ if (ioc->is_driver_loading) {
+
+
+
+ ioc->wait_for_discovery_to_complete =
+ _base_determine_wait_on_discovery(ioc);
+ return r; /* scan_start and scan_finished support */
+ }
+
+
+ if (ioc->wait_for_discovery_to_complete && ioc->is_warpdrive) {
if (ioc->manu_pg10.OEMIdentifier == 0x80) {
hide_flag = (u8) (ioc->manu_pg10.OEMSpecificFlags0 &
MFG_PAGE10_HIDE_SSDS_MASK);
@@ -3978,13 +4128,6 @@
}
}
- if (ioc->wait_for_port_enable_to_complete) {
- if (diag_buffer_enable != 0)
- mpt2sas_enable_diag_buffer(ioc, diag_buffer_enable);
- if (disable_discovery > 0)
- return r;
- }
-
r = _base_send_port_enable(ioc, sleep_flag);
if (r)
return r;
@@ -4121,6 +4264,10 @@
ioc->base_cmds.reply = kzalloc(ioc->reply_sz, GFP_KERNEL);
ioc->base_cmds.status = MPT2_CMD_NOT_USED;
+ /* port_enable command bits */
+ ioc->port_enable_cmds.reply = kzalloc(ioc->reply_sz, GFP_KERNEL);
+ ioc->port_enable_cmds.status = MPT2_CMD_NOT_USED;
+
/* transport internal command bits */
ioc->transport_cmds.reply = kzalloc(ioc->reply_sz, GFP_KERNEL);
ioc->transport_cmds.status = MPT2_CMD_NOT_USED;
@@ -4162,8 +4309,6 @@
goto out_free_resources;
}
- init_completion(&ioc->shost_recovery_done);
-
for (i = 0; i < MPI2_EVENT_NOTIFY_EVENTMASK_WORDS; i++)
ioc->event_masks[i] = -1;
@@ -4186,7 +4331,6 @@
_base_update_missing_delay(ioc, missing_delay[0],
missing_delay[1]);
- mpt2sas_base_start_watchdog(ioc);
return 0;
out_free_resources:
@@ -4204,6 +4348,7 @@
kfree(ioc->scsih_cmds.reply);
kfree(ioc->config_cmds.reply);
kfree(ioc->base_cmds.reply);
+ kfree(ioc->port_enable_cmds.reply);
kfree(ioc->ctl_cmds.reply);
kfree(ioc->ctl_cmds.sense);
kfree(ioc->pfacts);
@@ -4243,6 +4388,7 @@
kfree(ioc->ctl_cmds.reply);
kfree(ioc->ctl_cmds.sense);
kfree(ioc->base_cmds.reply);
+ kfree(ioc->port_enable_cmds.reply);
kfree(ioc->tm_cmds.reply);
kfree(ioc->transport_cmds.reply);
kfree(ioc->scsih_cmds.reply);
@@ -4284,6 +4430,20 @@
mpt2sas_base_free_smid(ioc, ioc->base_cmds.smid);
complete(&ioc->base_cmds.done);
}
+ if (ioc->port_enable_cmds.status & MPT2_CMD_PENDING) {
+ ioc->port_enable_failed = 1;
+ ioc->port_enable_cmds.status |= MPT2_CMD_RESET;
+ mpt2sas_base_free_smid(ioc, ioc->port_enable_cmds.smid);
+ if (ioc->is_driver_loading) {
+ ioc->start_scan_failed =
+ MPI2_IOCSTATUS_INTERNAL_ERROR;
+ ioc->start_scan = 0;
+ ioc->port_enable_cmds.status =
+ MPT2_CMD_NOT_USED;
+ } else
+ complete(&ioc->port_enable_cmds.done);
+
+ }
if (ioc->config_cmds.status & MPT2_CMD_PENDING) {
ioc->config_cmds.status |= MPT2_CMD_RESET;
mpt2sas_base_free_smid(ioc, ioc->config_cmds.smid);
@@ -4349,7 +4509,6 @@
{
int r;
unsigned long flags;
- u8 pe_complete = ioc->wait_for_port_enable_to_complete;
dtmprintk(ioc, printk(MPT2SAS_INFO_FMT "%s: enter\n", ioc->name,
__func__));
@@ -4396,7 +4555,8 @@
/* If this hard reset is called while port enable is active, then
* there is no reason to call make_ioc_operational
*/
- if (pe_complete) {
+ if (ioc->is_driver_loading && ioc->port_enable_failed) {
+ ioc->remove_host = 1;
r = -EFAULT;
goto out;
}
@@ -4410,7 +4570,6 @@
spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags);
ioc->ioc_reset_in_progress_status = r;
ioc->shost_recovery = 0;
- complete(&ioc->shost_recovery_done);
spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock, flags);
mutex_unlock(&ioc->reset_in_progress_mutex);
diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.h b/drivers/scsi/mpt2sas/mpt2sas_base.h
index 59354db..ce2bd9b 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_base.h
+++ b/drivers/scsi/mpt2sas/mpt2sas_base.h
@@ -655,7 +655,12 @@
* @ignore_loginfos: ignore loginfos during task management
* @remove_host: flag for when driver unloads, to avoid sending dev resets
* @pci_error_recovery: flag to prevent ioc access until slot reset completes
- * @wait_for_port_enable_to_complete:
+ * @wait_for_discovery_to_complete: flag set at driver load time when
+ * waiting on reporting devices
+ * @is_driver_loading: flag set at driver load time
+ * @port_enable_failed: flag set when port enable has failed
+ * @start_scan: flag set from scan_start callback, cleared from _mpt2sas_fw_work
+ * @start_scan_failed: means port enable failed, return's the ioc_status
* @msix_enable: flag indicating msix is enabled
* @msix_vector_count: number msix vectors
* @cpu_msix_table: table for mapping cpus to msix index
@@ -790,15 +795,20 @@
u8 shost_recovery;
struct mutex reset_in_progress_mutex;
- struct completion shost_recovery_done;
spinlock_t ioc_reset_in_progress_lock;
u8 ioc_link_reset_in_progress;
- int ioc_reset_in_progress_status;
+ u8 ioc_reset_in_progress_status;
u8 ignore_loginfos;
u8 remove_host;
u8 pci_error_recovery;
- u8 wait_for_port_enable_to_complete;
+ u8 wait_for_discovery_to_complete;
+ struct completion port_enable_done;
+ u8 is_driver_loading;
+ u8 port_enable_failed;
+
+ u8 start_scan;
+ u16 start_scan_failed;
u8 msix_enable;
u16 msix_vector_count;
@@ -814,11 +824,13 @@
u8 scsih_cb_idx;
u8 ctl_cb_idx;
u8 base_cb_idx;
+ u8 port_enable_cb_idx;
u8 config_cb_idx;
u8 tm_tr_cb_idx;
u8 tm_tr_volume_cb_idx;
u8 tm_sas_control_cb_idx;
struct _internal_cmd base_cmds;
+ struct _internal_cmd port_enable_cmds;
struct _internal_cmd transport_cmds;
struct _internal_cmd scsih_cmds;
struct _internal_cmd tm_cmds;
@@ -1001,6 +1013,8 @@
u8 mpt2sas_base_done(struct MPT2SAS_ADAPTER *ioc, u16 smid, u8 msix_index,
u32 reply);
+u8 mpt2sas_port_enable_done(struct MPT2SAS_ADAPTER *ioc, u16 smid,
+ u8 msix_index, u32 reply);
void *mpt2sas_base_get_reply_virt_addr(struct MPT2SAS_ADAPTER *ioc, u32 phys_addr);
u32 mpt2sas_base_get_iocstate(struct MPT2SAS_ADAPTER *ioc, int cooked);
@@ -1015,6 +1029,8 @@
void mpt2sas_halt_firmware(struct MPT2SAS_ADAPTER *ioc);
+int mpt2sas_port_enable(struct MPT2SAS_ADAPTER *ioc);
+
/* scsih shared API */
u8 mpt2sas_scsih_event_callback(struct MPT2SAS_ADAPTER *ioc, u8 msix_index,
u32 reply);
@@ -1032,6 +1048,8 @@
struct _sas_device *mpt2sas_scsih_sas_device_find_by_sas_address(
struct MPT2SAS_ADAPTER *ioc, u64 sas_address);
+void mpt2sas_port_enable_complete(struct MPT2SAS_ADAPTER *ioc);
+
void mpt2sas_scsih_reset_handler(struct MPT2SAS_ADAPTER *ioc, int reset_phase);
/* config shared API */
diff --git a/drivers/scsi/mpt2sas/mpt2sas_ctl.c b/drivers/scsi/mpt2sas/mpt2sas_ctl.c
index 9adb013..aabcb91 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_ctl.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_ctl.c
@@ -1207,6 +1207,9 @@
if (_ctl_verify_adapter(karg.hdr.ioc_number, &ioc) == -1 || !ioc)
return -ENODEV;
+ if (ioc->shost_recovery || ioc->pci_error_recovery ||
+ ioc->is_driver_loading)
+ return -EAGAIN;
dctlprintk(ioc, printk(MPT2SAS_INFO_FMT "%s: enter\n", ioc->name,
__func__));
@@ -2178,7 +2181,8 @@
!ioc)
return -ENODEV;
- if (ioc->shost_recovery || ioc->pci_error_recovery)
+ if (ioc->shost_recovery || ioc->pci_error_recovery ||
+ ioc->is_driver_loading)
return -EAGAIN;
if (_IOC_SIZE(cmd) == sizeof(struct mpt2_ioctl_command)) {
@@ -2297,7 +2301,8 @@
if (_ctl_verify_adapter(karg32.hdr.ioc_number, &ioc) == -1 || !ioc)
return -ENODEV;
- if (ioc->shost_recovery || ioc->pci_error_recovery)
+ if (ioc->shost_recovery || ioc->pci_error_recovery ||
+ ioc->is_driver_loading)
return -EAGAIN;
memset(&karg, 0, sizeof(struct mpt2_ioctl_command));
diff --git a/drivers/scsi/mpt2sas/mpt2sas_scsih.c b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
index 1da1aa1..7a3865d 100644
--- a/drivers/scsi/mpt2sas/mpt2sas_scsih.c
+++ b/drivers/scsi/mpt2sas/mpt2sas_scsih.c
@@ -71,6 +71,9 @@
static u8 _scsih_check_for_pending_tm(struct MPT2SAS_ADAPTER *ioc, u16 smid);
+static void _scsih_scan_start(struct Scsi_Host *shost);
+static int _scsih_scan_finished(struct Scsi_Host *shost, unsigned long time);
+
/* global parameters */
LIST_HEAD(mpt2sas_ioc_list);
@@ -79,6 +82,7 @@
static u8 tm_cb_idx = -1;
static u8 ctl_cb_idx = -1;
static u8 base_cb_idx = -1;
+static u8 port_enable_cb_idx = -1;
static u8 transport_cb_idx = -1;
static u8 scsih_cb_idx = -1;
static u8 config_cb_idx = -1;
@@ -103,6 +107,18 @@
module_param(max_lun, int, 0);
MODULE_PARM_DESC(max_lun, " max lun, default=16895 ");
+/* diag_buffer_enable is bitwise
+ * bit 0 set = TRACE
+ * bit 1 set = SNAPSHOT
+ * bit 2 set = EXTENDED
+ *
+ * Either bit can be set, or both
+ */
+static int diag_buffer_enable = -1;
+module_param(diag_buffer_enable, int, 0);
+MODULE_PARM_DESC(diag_buffer_enable, " post diag buffers "
+ "(TRACE=1/SNAPSHOT=2/EXTENDED=4/default=0)");
+
/**
* struct sense_info - common structure for obtaining sense keys
* @skey: sense key
@@ -117,8 +133,8 @@
#define MPT2SAS_TURN_ON_FAULT_LED (0xFFFC)
-#define MPT2SAS_RESCAN_AFTER_HOST_RESET (0xFFFF)
-
+#define MPT2SAS_PORT_ENABLE_COMPLETE (0xFFFD)
+#define MPT2SAS_REMOVE_UNRESPONDING_DEVICES (0xFFFF)
/**
* struct fw_event_work - firmware event struct
* @list: link list framework
@@ -424,7 +440,11 @@
u16 slot;
/* only process this function when driver loads */
- if (!ioc->wait_for_port_enable_to_complete)
+ if (!ioc->is_driver_loading)
+ return;
+
+ /* no Bios, return immediately */
+ if (!ioc->bios_pg3.BiosVersion)
return;
if (!is_raid) {
@@ -2714,22 +2734,38 @@
/**
- * _scsih_queue_rescan - queue a topology rescan from user context
+ * _scsih_error_recovery_delete_devices - remove devices not responding
* @ioc: per adapter object
*
* Return nothing.
*/
static void
-_scsih_queue_rescan(struct MPT2SAS_ADAPTER *ioc)
+_scsih_error_recovery_delete_devices(struct MPT2SAS_ADAPTER *ioc)
{
struct fw_event_work *fw_event;
- if (ioc->wait_for_port_enable_to_complete)
+ if (ioc->is_driver_loading)
return;
+ fw_event->event = MPT2SAS_REMOVE_UNRESPONDING_DEVICES;
+ fw_event->ioc = ioc;
+ _scsih_fw_event_add(ioc, fw_event);
+}
+
+/**
+ * mpt2sas_port_enable_complete - port enable completed (fake event)
+ * @ioc: per adapter object
+ *
+ * Return nothing.
+ */
+void
+mpt2sas_port_enable_complete(struct MPT2SAS_ADAPTER *ioc)
+{
+ struct fw_event_work *fw_event;
+
fw_event = kzalloc(sizeof(struct fw_event_work), GFP_ATOMIC);
if (!fw_event)
return;
- fw_event->event = MPT2SAS_RESCAN_AFTER_HOST_RESET;
+ fw_event->event = MPT2SAS_PORT_ENABLE_COMPLETE;
fw_event->ioc = ioc;
_scsih_fw_event_add(ioc, fw_event);
}
@@ -5099,7 +5135,7 @@
/* get device name */
sas_device->device_name = le64_to_cpu(sas_device_pg0.DeviceName);
- if (ioc->wait_for_port_enable_to_complete)
+ if (ioc->wait_for_discovery_to_complete)
_scsih_sas_device_init_add(ioc, sas_device);
else
_scsih_sas_device_add(ioc, sas_device);
@@ -5622,7 +5658,7 @@
termination_count = 0;
query_count = 0;
for (smid = 1; smid <= ioc->scsiio_depth; smid++) {
- if (ioc->ioc_reset_in_progress_status)
+ if (ioc->shost_recovery)
goto out;
scmd = _scsih_scsi_lookup_get(ioc, smid);
if (!scmd)
@@ -5644,7 +5680,7 @@
lun = sas_device_priv_data->lun;
query_count++;
- if (ioc->ioc_reset_in_progress_status)
+ if (ioc->shost_recovery)
goto out;
spin_unlock_irqrestore(&ioc->scsi_lookup_lock, flags);
@@ -5686,7 +5722,7 @@
goto broadcast_aen_retry;
}
- if (ioc->ioc_reset_in_progress_status)
+ if (ioc->shost_recovery)
goto out_no_lock;
r = mpt2sas_scsih_issue_tm(ioc, handle, sdev->channel, sdev->id,
@@ -5725,7 +5761,7 @@
ioc->name, __func__, query_count, termination_count));
ioc->broadcast_aen_busy = 0;
- if (!ioc->ioc_reset_in_progress_status)
+ if (!ioc->shost_recovery)
_scsih_ublock_io_all_device(ioc);
mutex_unlock(&ioc->tm_cmds.mutex);
}
@@ -5845,7 +5881,7 @@
raid_device->handle = handle;
raid_device->wwid = wwid;
_scsih_raid_device_add(ioc, raid_device);
- if (!ioc->wait_for_port_enable_to_complete) {
+ if (!ioc->wait_for_discovery_to_complete) {
rc = scsi_add_device(ioc->shost, RAID_CHANNEL,
raid_device->id, 0);
if (rc)
@@ -6127,6 +6163,10 @@
_scsih_sas_ir_config_change_event_debug(ioc, event_data);
#endif
+
+ if (ioc->shost_recovery)
+ return;
+
foreign_config = (le32_to_cpu(event_data->Flags) &
MPI2_EVENT_IR_CHANGE_FLAGS_FOREIGN_CONFIG) ? 1 : 0;
@@ -6185,6 +6225,9 @@
int rc;
Mpi2EventDataIrVolume_t *event_data = fw_event->event_data;
+ if (ioc->shost_recovery)
+ return;
+
if (event_data->ReasonCode != MPI2_EVENT_IR_VOLUME_RC_STATE_CHANGED)
return;
@@ -6267,6 +6310,9 @@
Mpi2EventDataIrPhysicalDisk_t *event_data = fw_event->event_data;
u64 sas_address;
+ if (ioc->shost_recovery)
+ return;
+
if (event_data->ReasonCode != MPI2_EVENT_IR_PHYSDISK_RC_STATE_CHANGED)
return;
@@ -6510,10 +6556,10 @@
u32 device_info;
u16 slot;
- printk(MPT2SAS_INFO_FMT "%s\n", ioc->name, __func__);
+ printk(MPT2SAS_INFO_FMT "search for end-devices: start\n", ioc->name);
if (list_empty(&ioc->sas_device_list))
- return;
+ goto out;
handle = 0xFFFF;
while (!(mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply,
@@ -6532,6 +6578,9 @@
_scsih_mark_responding_sas_device(ioc, sas_address, slot,
handle);
}
+out:
+ printk(MPT2SAS_INFO_FMT "search for end-devices: complete\n",
+ ioc->name);
}
/**
@@ -6607,10 +6656,14 @@
u16 handle;
u8 phys_disk_num;
- printk(MPT2SAS_INFO_FMT "%s\n", ioc->name, __func__);
+ if (!ioc->ir_firmware)
+ return;
+
+ printk(MPT2SAS_INFO_FMT "search for raid volumes: start\n",
+ ioc->name);
if (list_empty(&ioc->raid_device_list))
- return;
+ goto out;
handle = 0xFFFF;
while (!(mpt2sas_config_get_raid_volume_pg1(ioc, &mpi_reply,
@@ -6649,6 +6702,9 @@
set_bit(handle, ioc->pd_handles);
}
}
+out:
+ printk(MPT2SAS_INFO_FMT "search for responding raid volumes: "
+ "complete\n", ioc->name);
}
/**
@@ -6708,10 +6764,10 @@
u64 sas_address;
u16 handle;
- printk(MPT2SAS_INFO_FMT "%s\n", ioc->name, __func__);
+ printk(MPT2SAS_INFO_FMT "search for expanders: start\n", ioc->name);
if (list_empty(&ioc->sas_expander_list))
- return;
+ goto out;
handle = 0xFFFF;
while (!(mpt2sas_config_get_expander_pg0(ioc, &mpi_reply, &expander_pg0,
@@ -6730,6 +6786,8 @@
_scsih_mark_responding_expander(ioc, sas_address, handle);
}
+ out:
+ printk(MPT2SAS_INFO_FMT "search for expanders: complete\n", ioc->name);
}
/**
@@ -6745,6 +6803,8 @@
struct _sas_node *sas_expander;
struct _raid_device *raid_device, *raid_device_next;
+ printk(MPT2SAS_INFO_FMT "removing unresponding devices: start\n",
+ ioc->name);
list_for_each_entry_safe(sas_device, sas_device_next,
&ioc->sas_device_list, list) {
@@ -6764,6 +6824,9 @@
_scsih_remove_device(ioc, sas_device);
}
+ if (!ioc->ir_firmware)
+ goto retry_expander_search;
+
list_for_each_entry_safe(raid_device, raid_device_next,
&ioc->raid_device_list, list) {
if (raid_device->responding) {
@@ -6790,52 +6853,170 @@
mpt2sas_expander_remove(ioc, sas_expander->sas_address);
goto retry_expander_search;
}
+ printk(MPT2SAS_INFO_FMT "removing unresponding devices: complete\n",
+ ioc->name);
+ /* unblock devices */
+ _scsih_ublock_io_all_device(ioc);
+}
+
+static void
+_scsih_refresh_expander_links(struct MPT2SAS_ADAPTER *ioc,
+ struct _sas_node *sas_expander, u16 handle)
+{
+ Mpi2ExpanderPage1_t expander_pg1;
+ Mpi2ConfigReply_t mpi_reply;
+ int i;
+
+ for (i = 0 ; i < sas_expander->num_phys ; i++) {
+ if ((mpt2sas_config_get_expander_pg1(ioc, &mpi_reply,
+ &expander_pg1, i, handle))) {
+ printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
+ ioc->name, __FILE__, __LINE__, __func__);
+ return;
+ }
+
+ mpt2sas_transport_update_links(ioc, sas_expander->sas_address,
+ le16_to_cpu(expander_pg1.AttachedDevHandle), i,
+ expander_pg1.NegotiatedLinkRate >> 4);
+ }
}
/**
- * _scsih_hide_unhide_sas_devices - add/remove device to/from OS
+ * _scsih_scan_for_devices_after_reset - scan for devices after host reset
* @ioc: per adapter object
*
* Return nothing.
*/
static void
-_scsih_hide_unhide_sas_devices(struct MPT2SAS_ADAPTER *ioc)
+_scsih_scan_for_devices_after_reset(struct MPT2SAS_ADAPTER *ioc)
{
- struct _sas_device *sas_device, *sas_device_next;
+ Mpi2ExpanderPage0_t expander_pg0;
+ Mpi2SasDevicePage0_t sas_device_pg0;
+ Mpi2RaidVolPage1_t volume_pg1;
+ Mpi2RaidVolPage0_t volume_pg0;
+ Mpi2RaidPhysDiskPage0_t pd_pg0;
+ Mpi2EventIrConfigElement_t element;
+ Mpi2ConfigReply_t mpi_reply;
+ u8 phys_disk_num;
+ u16 ioc_status;
+ u16 handle, parent_handle;
+ u64 sas_address;
+ struct _sas_device *sas_device;
+ struct _sas_node *expander_device;
+ static struct _raid_device *raid_device;
- if (!ioc->is_warpdrive || ioc->mfg_pg10_hide_flag !=
- MFG_PAGE10_HIDE_IF_VOL_PRESENT)
- return;
+ printk(MPT2SAS_INFO_FMT "scan devices: start\n", ioc->name);
- if (ioc->hide_drives) {
- if (_scsih_get_num_volumes(ioc))
- return;
- ioc->hide_drives = 0;
- list_for_each_entry_safe(sas_device, sas_device_next,
- &ioc->sas_device_list, list) {
- if (!mpt2sas_transport_port_add(ioc, sas_device->handle,
- sas_device->sas_address_parent)) {
- _scsih_sas_device_remove(ioc, sas_device);
- } else if (!sas_device->starget) {
- mpt2sas_transport_port_remove(ioc,
- sas_device->sas_address,
- sas_device->sas_address_parent);
- _scsih_sas_device_remove(ioc, sas_device);
- }
- }
- } else {
- if (!_scsih_get_num_volumes(ioc))
- return;
- ioc->hide_drives = 1;
- list_for_each_entry_safe(sas_device, sas_device_next,
- &ioc->sas_device_list, list) {
- mpt2sas_transport_port_remove(ioc,
- sas_device->sas_address,
- sas_device->sas_address_parent);
+ _scsih_sas_host_refresh(ioc);
+
+ /* expanders */
+ handle = 0xFFFF;
+ while (!(mpt2sas_config_get_expander_pg0(ioc, &mpi_reply, &expander_pg0,
+ MPI2_SAS_EXPAND_PGAD_FORM_GET_NEXT_HNDL, handle))) {
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
+ break;
+ handle = le16_to_cpu(expander_pg0.DevHandle);
+ expander_device = mpt2sas_scsih_expander_find_by_sas_address(
+ ioc, le64_to_cpu(expander_pg0.SASAddress));
+ if (expander_device)
+ _scsih_refresh_expander_links(ioc, expander_device,
+ handle);
+ else
+ _scsih_expander_add(ioc, handle);
+ }
+
+ if (!ioc->ir_firmware)
+ goto skip_to_sas;
+
+ /* phys disk */
+ phys_disk_num = 0xFF;
+ while (!(mpt2sas_config_get_phys_disk_pg0(ioc, &mpi_reply,
+ &pd_pg0, MPI2_PHYSDISK_PGAD_FORM_GET_NEXT_PHYSDISKNUM,
+ phys_disk_num))) {
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
+ break;
+ phys_disk_num = pd_pg0.PhysDiskNum;
+ handle = le16_to_cpu(pd_pg0.DevHandle);
+ sas_device = _scsih_sas_device_find_by_handle(ioc, handle);
+ if (sas_device)
+ continue;
+ if (mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply,
+ &sas_device_pg0, MPI2_SAS_DEVICE_PGAD_FORM_HANDLE,
+ handle) != 0)
+ continue;
+ parent_handle = le16_to_cpu(sas_device_pg0.ParentDevHandle);
+ if (!_scsih_get_sas_address(ioc, parent_handle,
+ &sas_address)) {
+ mpt2sas_transport_update_links(ioc, sas_address,
+ handle, sas_device_pg0.PhyNum,
+ MPI2_SAS_NEG_LINK_RATE_1_5);
+ set_bit(handle, ioc->pd_handles);
+ _scsih_add_device(ioc, handle, 0, 1);
}
}
+
+ /* volumes */
+ handle = 0xFFFF;
+ while (!(mpt2sas_config_get_raid_volume_pg1(ioc, &mpi_reply,
+ &volume_pg1, MPI2_RAID_VOLUME_PGAD_FORM_GET_NEXT_HANDLE, handle))) {
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
+ break;
+ handle = le16_to_cpu(volume_pg1.DevHandle);
+ raid_device = _scsih_raid_device_find_by_wwid(ioc,
+ le64_to_cpu(volume_pg1.WWID));
+ if (raid_device)
+ continue;
+ if (mpt2sas_config_get_raid_volume_pg0(ioc, &mpi_reply,
+ &volume_pg0, MPI2_RAID_VOLUME_PGAD_FORM_HANDLE, handle,
+ sizeof(Mpi2RaidVolPage0_t)))
+ continue;
+ if (volume_pg0.VolumeState == MPI2_RAID_VOL_STATE_OPTIMAL ||
+ volume_pg0.VolumeState == MPI2_RAID_VOL_STATE_ONLINE ||
+ volume_pg0.VolumeState == MPI2_RAID_VOL_STATE_DEGRADED) {
+ memset(&element, 0, sizeof(Mpi2EventIrConfigElement_t));
+ element.ReasonCode = MPI2_EVENT_IR_CHANGE_RC_ADDED;
+ element.VolDevHandle = volume_pg1.DevHandle;
+ _scsih_sas_volume_add(ioc, &element);
+ }
+ }
+
+ skip_to_sas:
+
+ /* sas devices */
+ handle = 0xFFFF;
+ while (!(mpt2sas_config_get_sas_device_pg0(ioc, &mpi_reply,
+ &sas_device_pg0, MPI2_SAS_DEVICE_PGAD_FORM_GET_NEXT_HANDLE,
+ handle))) {
+ ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
+ MPI2_IOCSTATUS_MASK;
+ if (ioc_status == MPI2_IOCSTATUS_CONFIG_INVALID_PAGE)
+ break;
+ handle = le16_to_cpu(sas_device_pg0.DevHandle);
+ if (!(_scsih_is_end_device(
+ le32_to_cpu(sas_device_pg0.DeviceInfo))))
+ continue;
+ sas_device = mpt2sas_scsih_sas_device_find_by_sas_address(ioc,
+ le64_to_cpu(sas_device_pg0.SASAddress));
+ if (sas_device)
+ continue;
+ parent_handle = le16_to_cpu(sas_device_pg0.ParentDevHandle);
+ if (!_scsih_get_sas_address(ioc, parent_handle, &sas_address)) {
+ mpt2sas_transport_update_links(ioc, sas_address, handle,
+ sas_device_pg0.PhyNum, MPI2_SAS_NEG_LINK_RATE_1_5);
+ _scsih_add_device(ioc, handle, 0, 0);
+ }
+ }
+
+ printk(MPT2SAS_INFO_FMT "scan devices: complete\n", ioc->name);
}
+
/**
* mpt2sas_scsih_reset_handler - reset callback handler (for scsih)
* @ioc: per adapter object
@@ -6871,7 +7052,6 @@
}
_scsih_fw_event_cleanup_queue(ioc);
_scsih_flush_running_cmds(ioc);
- _scsih_queue_rescan(ioc);
break;
case MPT2_IOC_DONE_RESET:
dtmprintk(ioc, printk(MPT2SAS_INFO_FMT "%s: "
@@ -6881,6 +7061,7 @@
_scsih_search_responding_sas_devices(ioc);
_scsih_search_responding_raid_devices(ioc);
_scsih_search_responding_expanders(ioc);
+ _scsih_error_recovery_delete_devices(ioc);
break;
}
}
@@ -6898,7 +7079,6 @@
{
struct fw_event_work *fw_event = container_of(work,
struct fw_event_work, delayed_work.work);
- unsigned long flags;
struct MPT2SAS_ADAPTER *ioc = fw_event->ioc;
/* the queue is being flushed so ignore this event */
@@ -6908,23 +7088,31 @@
return;
}
- if (fw_event->event == MPT2SAS_RESCAN_AFTER_HOST_RESET) {
- _scsih_fw_event_free(ioc, fw_event);
- spin_lock_irqsave(&ioc->ioc_reset_in_progress_lock, flags);
- if (ioc->shost_recovery) {
- init_completion(&ioc->shost_recovery_done);
- spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock,
- flags);
- wait_for_completion(&ioc->shost_recovery_done);
- } else
- spin_unlock_irqrestore(&ioc->ioc_reset_in_progress_lock,
- flags);
- _scsih_remove_unresponding_sas_devices(ioc);
- _scsih_hide_unhide_sas_devices(ioc);
- return;
- }
-
switch (fw_event->event) {
+ case MPT2SAS_REMOVE_UNRESPONDING_DEVICES:
+ while (scsi_host_in_recovery(ioc->shost))
+ ssleep(1);
+ _scsih_remove_unresponding_sas_devices(ioc);
+ _scsih_scan_for_devices_after_reset(ioc);
+ break;
+ case MPT2SAS_PORT_ENABLE_COMPLETE:
+ if (!ioc->is_driver_loading && ioc->shost_recovery) {
+ _scsih_prep_device_scan(ioc);
+ _scsih_search_responding_sas_devices(ioc);
+ _scsih_search_responding_raid_devices(ioc);
+ _scsih_search_responding_expanders(ioc);
+ }
+
+ if (ioc->start_scan)
+ ioc->start_scan = 0;
+ else
+ complete(&ioc->port_enable_done);
+
+
+
+ dewtprintk(ioc, printk(MPT2SAS_INFO_FMT "port enable: complete "
+ "from worker thread\n", ioc->name));
+ break;
case MPT2SAS_TURN_ON_FAULT_LED:
_scsih_turn_on_fault_led(ioc, fw_event->device_handle);
break;
@@ -7121,6 +7309,8 @@
.slave_configure = _scsih_slave_configure,
.target_destroy = _scsih_target_destroy,
.slave_destroy = _scsih_slave_destroy,
+ .scan_finished = _scsih_scan_finished,
+ .scan_start = _scsih_scan_start,
.change_queue_depth = _scsih_change_queue_depth,
.change_queue_type = _scsih_change_queue_type,
.eh_abort_handler = _scsih_abort,
@@ -7381,7 +7571,12 @@
unsigned long flags;
int rc;
+ /* no Bios, return immediately */
+ if (!ioc->bios_pg3.BiosVersion)
+ return;
+
device = NULL;
+ is_raid = 0;
if (ioc->req_boot_device.device) {
device = ioc->req_boot_device.device;
is_raid = ioc->req_boot_device.is_raid;
@@ -7490,9 +7685,7 @@
static void
_scsih_probe_devices(struct MPT2SAS_ADAPTER *ioc)
{
- u16 volume_mapping_flags =
- le16_to_cpu(ioc->ioc_pg8.IRVolumeMappingFlags) &
- MPI2_IOCPAGE8_IRFLAGS_MASK_VOLUME_MAPPING_MODE;
+ u16 volume_mapping_flags;
if (!(ioc->facts.ProtocolFlags & MPI2_IOCFACTS_PROTOCOL_SCSI_INITIATOR))
return; /* return when IOC doesn't support initiator mode */
@@ -7500,18 +7693,93 @@
_scsih_probe_boot_devices(ioc);
if (ioc->ir_firmware) {
- if ((volume_mapping_flags &
- MPI2_IOCPAGE8_IRFLAGS_HIGH_VOLUME_MAPPING)) {
- _scsih_probe_sas(ioc);
+ volume_mapping_flags =
+ le16_to_cpu(ioc->ioc_pg8.IRVolumeMappingFlags) &
+ MPI2_IOCPAGE8_IRFLAGS_MASK_VOLUME_MAPPING_MODE;
+ if (volume_mapping_flags ==
+ MPI2_IOCPAGE8_IRFLAGS_LOW_VOLUME_MAPPING) {
_scsih_probe_raid(ioc);
+ _scsih_probe_sas(ioc);
} else {
- _scsih_probe_raid(ioc);
_scsih_probe_sas(ioc);
+ _scsih_probe_raid(ioc);
}
} else
_scsih_probe_sas(ioc);
}
+
+/**
+ * _scsih_scan_start - scsi lld callback for .scan_start
+ * @shost: SCSI host pointer
+ *
+ * The shost has the ability to discover targets on its own instead
+ * of scanning the entire bus. In our implemention, we will kick off
+ * firmware discovery.
+ */
+static void
+_scsih_scan_start(struct Scsi_Host *shost)
+{
+ struct MPT2SAS_ADAPTER *ioc = shost_priv(shost);
+ int rc;
+
+ if (diag_buffer_enable != -1 && diag_buffer_enable != 0)
+ mpt2sas_enable_diag_buffer(ioc, diag_buffer_enable);
+
+ ioc->start_scan = 1;
+ rc = mpt2sas_port_enable(ioc);
+
+ if (rc != 0)
+ printk(MPT2SAS_INFO_FMT "port enable: FAILED\n", ioc->name);
+}
+
+/**
+ * _scsih_scan_finished - scsi lld callback for .scan_finished
+ * @shost: SCSI host pointer
+ * @time: elapsed time of the scan in jiffies
+ *
+ * This function will be called periodically until it returns 1 with the
+ * scsi_host and the elapsed time of the scan in jiffies. In our implemention,
+ * we wait for firmware discovery to complete, then return 1.
+ */
+static int
+_scsih_scan_finished(struct Scsi_Host *shost, unsigned long time)
+{
+ struct MPT2SAS_ADAPTER *ioc = shost_priv(shost);
+
+ if (time >= (300 * HZ)) {
+ ioc->base_cmds.status = MPT2_CMD_NOT_USED;
+ printk(MPT2SAS_INFO_FMT "port enable: FAILED with timeout "
+ "(timeout=300s)\n", ioc->name);
+ ioc->is_driver_loading = 0;
+ return 1;
+ }
+
+ if (ioc->start_scan)
+ return 0;
+
+ if (ioc->start_scan_failed) {
+ printk(MPT2SAS_INFO_FMT "port enable: FAILED with "
+ "(ioc_status=0x%08x)\n", ioc->name, ioc->start_scan_failed);
+ ioc->is_driver_loading = 0;
+ ioc->wait_for_discovery_to_complete = 0;
+ ioc->remove_host = 1;
+ return 1;
+ }
+
+ printk(MPT2SAS_INFO_FMT "port enable: SUCCESS\n", ioc->name);
+ ioc->base_cmds.status = MPT2_CMD_NOT_USED;
+
+ if (ioc->wait_for_discovery_to_complete) {
+ ioc->wait_for_discovery_to_complete = 0;
+ _scsih_probe_devices(ioc);
+ }
+ mpt2sas_base_start_watchdog(ioc);
+ ioc->is_driver_loading = 0;
+ return 1;
+}
+
+
/**
* _scsih_probe - attach and add scsi host
* @pdev: PCI device struct
@@ -7548,6 +7816,7 @@
ioc->tm_cb_idx = tm_cb_idx;
ioc->ctl_cb_idx = ctl_cb_idx;
ioc->base_cb_idx = base_cb_idx;
+ ioc->port_enable_cb_idx = port_enable_cb_idx;
ioc->transport_cb_idx = transport_cb_idx;
ioc->scsih_cb_idx = scsih_cb_idx;
ioc->config_cb_idx = config_cb_idx;
@@ -7620,14 +7889,14 @@
goto out_thread_fail;
}
- ioc->wait_for_port_enable_to_complete = 1;
+ ioc->is_driver_loading = 1;
if ((mpt2sas_base_attach(ioc))) {
printk(MPT2SAS_ERR_FMT "failure at %s:%d/%s()!\n",
ioc->name, __FILE__, __LINE__, __func__);
goto out_attach_fail;
}
- ioc->wait_for_port_enable_to_complete = 0;
+ scsi_scan_host(shost);
if (ioc->is_warpdrive) {
if (ioc->mfg_pg10_hide_flag == MFG_PAGE10_EXPOSE_ALL_DISKS)
ioc->hide_drives = 0;
@@ -7650,6 +7919,7 @@
out_thread_fail:
list_del(&ioc->list);
scsi_remove_host(shost);
+ scsi_host_put(shost);
out_add_shost_fail:
return -ENODEV;
}
@@ -7896,6 +8166,8 @@
/* base internal commands callback handler */
base_cb_idx = mpt2sas_base_register_callback_handler(mpt2sas_base_done);
+ port_enable_cb_idx = mpt2sas_base_register_callback_handler(
+ mpt2sas_port_enable_done);
/* transport internal commands callback handler */
transport_cb_idx = mpt2sas_base_register_callback_handler(
@@ -7950,6 +8222,7 @@
mpt2sas_base_release_callback_handler(scsi_io_cb_idx);
mpt2sas_base_release_callback_handler(tm_cb_idx);
mpt2sas_base_release_callback_handler(base_cb_idx);
+ mpt2sas_base_release_callback_handler(port_enable_cb_idx);
mpt2sas_base_release_callback_handler(transport_cb_idx);
mpt2sas_base_release_callback_handler(scsih_cb_idx);
mpt2sas_base_release_callback_handler(config_cb_idx);