sky2: Yukon Extreme support
This is basic support for the new Yukon Extreme
chip, extracted from the new vendor driver 10.0.4.3.
Since this is untested hardware, it has a big fat warning for now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index c96362d..8cd38eb 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -140,7 +140,7 @@
static const char *yukon2_name[] = {
"XL", /* 0xb3 */
"EC Ultra", /* 0xb4 */
- "UNKNOWN", /* 0xb5 */
+ "Extreme", /* 0xb5 */
"EC", /* 0xb6 */
"FE", /* 0xb7 */
};
@@ -211,7 +211,7 @@
else
sky2_write8(hw, B2_Y2_CLK_GATE, 0);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) {
u32 reg1;
sky2_pci_write32(hw, PCI_DEV_REG3, 0);
@@ -289,8 +289,10 @@
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg;
- if (sky2->autoneg == AUTONEG_ENABLE &&
- !(hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
+ if (sky2->autoneg == AUTONEG_ENABLE
+ && !(hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX)) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
@@ -317,8 +319,10 @@
/* enable automatic crossover */
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
- if (sky2->autoneg == AUTONEG_ENABLE &&
- (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
+ if (sky2->autoneg == AUTONEG_ENABLE
+ && (hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX)) {
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
@@ -473,7 +477,9 @@
/* restore page register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
+
case CHIP_ID_YUKON_EC_U:
+ case CHIP_ID_YUKON_EX:
pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
/* select page 3 to access LED control register */
@@ -515,7 +521,7 @@
/* set page register to 0 */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
- } else {
+ } else if (hw->chip_id != CHIP_ID_YUKON_EX) {
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) {
@@ -727,7 +733,7 @@
sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR);
sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON);
- if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) {
sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8);
sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8);
if (hw->dev[port]->mtu > ETH_DATA_LEN) {
@@ -1687,7 +1693,9 @@
sky2_write8(hw, SK_REG(port, LNK_LED_REG),
LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
- if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U) {
+ if (hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
u16 led = PHY_M_LEDC_LOS_CTRL(1); /* link active */
@@ -1780,14 +1788,16 @@
sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF;
/* Pause bits are offset (9..8) */
- if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)
+ if (hw->chip_id == CHIP_ID_YUKON_XL
+ || hw->chip_id == CHIP_ID_YUKON_EC_U
+ || hw->chip_id == CHIP_ID_YUKON_EX)
aux >>= 6;
sky2->flow_status = sky2_flow(aux & PHY_M_PS_RX_P_EN,
aux & PHY_M_PS_TX_P_EN);
if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000
- && hw->chip_id != CHIP_ID_YUKON_EC_U)
+ && !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX))
sky2->flow_status = FC_NONE;
if (aux & PHY_M_PS_RX_P_EN)
@@ -2442,6 +2452,7 @@
switch (hw->chip_id) {
case CHIP_ID_YUKON_EC:
case CHIP_ID_YUKON_EC_U:
+ case CHIP_ID_YUKON_EX:
return 125; /* 125 Mhz */
case CHIP_ID_YUKON_FE:
return 100; /* 100 Mhz */
@@ -2474,6 +2485,14 @@
return -EOPNOTSUPP;
}
+ if (hw->chip_id == CHIP_ID_YUKON_EX)
+ dev_warn(&hw->pdev->dev, "this driver not yet tested on this chip type\n"
+ "Please report success or failure to <netdev@vger.kernel.org>\n");
+
+ /* Make sure and enable all clocks */
+ if (hw->chip_id == CHIP_ID_YUKON_EX || hw->chip_id == CHIP_ID_YUKON_EC_U)
+ sky2_pci_write32(hw, PCI_DEV_REG3, 0);
+
hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4;
/* This rev is really old, and requires untested workarounds */
@@ -2502,7 +2521,13 @@
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
- sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
+ if (hw->chip_id == CHIP_ID_YUKON_EX) {
+ status = sky2_read16(hw, HCU_CCSR);
+ status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE |
+ HCU_CCSR_UC_STATE_MSK);
+ sky2_write16(hw, HCU_CCSR, status);
+ } else
+ sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE);
}