| config MTD_NAND_ECC |
| tristate |
| |
| config MTD_NAND_ECC_SMC |
| bool "NAND ECC Smart Media byte order" |
| depends on MTD_NAND_ECC |
| default n |
| help |
| Software ECC according to the Smart Media Specification. |
| The original Linux implementation had byte 0 and 1 swapped. |
| |
| |
| menuconfig MTD_NAND |
| tristate "NAND Device Support" |
| depends on MTD |
| select MTD_NAND_IDS |
| select MTD_NAND_ECC |
| help |
| This enables support for accessing all type of NAND flash |
| devices. For further information see |
| <http://www.linux-mtd.infradead.org/doc/nand.html>. |
| |
| if MTD_NAND |
| |
| config MTD_NAND_BCH |
| tristate |
| select BCH |
| depends on MTD_NAND_ECC_BCH |
| default MTD_NAND |
| |
| config MTD_NAND_ECC_BCH |
| bool "Support software BCH ECC" |
| default n |
| help |
| This enables support for software BCH error correction. Binary BCH |
| codes are more powerful and cpu intensive than traditional Hamming |
| ECC codes. They are used with NAND devices requiring more than 1 bit |
| of error correction. |
| |
| config MTD_SM_COMMON |
| tristate |
| default n |
| |
| config MTD_NAND_DENALI |
| tristate "Support Denali NAND controller" |
| depends on HAS_DMA |
| help |
| Enable support for the Denali NAND controller. This should be |
| combined with either the PCI or platform drivers to provide device |
| registration. |
| |
| config MTD_NAND_DENALI_PCI |
| tristate "Support Denali NAND controller on Intel Moorestown" |
| depends on PCI && MTD_NAND_DENALI |
| help |
| Enable the driver for NAND flash on Intel Moorestown, using the |
| Denali NAND controller core. |
| |
| config MTD_NAND_DENALI_DT |
| tristate "Support Denali NAND controller as a DT device" |
| depends on HAVE_CLK && MTD_NAND_DENALI |
| help |
| Enable the driver for NAND flash on platforms using a Denali NAND |
| controller as a DT device. |
| |
| config MTD_NAND_DENALI_SCRATCH_REG_ADDR |
| hex "Denali NAND size scratch register address" |
| default "0xFF108018" |
| depends on MTD_NAND_DENALI_PCI |
| help |
| Some platforms place the NAND chip size in a scratch register |
| because (some versions of) the driver aren't able to automatically |
| determine the size of certain chips. Set the address of the |
| scratch register here to enable this feature. On Intel Moorestown |
| boards, the scratch register is at 0xFF108018. |
| |
| config MTD_NAND_GPIO |
| tristate "GPIO NAND Flash driver" |
| depends on GPIOLIB |
| help |
| This enables a GPIO based NAND flash driver. |
| |
| config MTD_NAND_AMS_DELTA |
| tristate "NAND Flash device on Amstrad E3" |
| depends on MACH_AMS_DELTA |
| default y |
| help |
| Support for NAND flash on Amstrad E3 (Delta). |
| |
| config MTD_NAND_OMAP2 |
| tristate "NAND Flash device on OMAP2, OMAP3 and OMAP4" |
| depends on ARCH_OMAP2PLUS |
| help |
| Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4 |
| platforms. |
| |
| config MTD_NAND_OMAP_BCH |
| depends on MTD_NAND_OMAP2 |
| tristate "Support hardware based BCH error correction" |
| default n |
| select BCH |
| help |
| This config enables the ELM hardware engine, which can be used to |
| locate and correct errors when using BCH ECC scheme. This offloads |
| the cpu from doing ECC error searching and correction. However some |
| legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine |
| so they should not enable this config symbol. |
| |
| config MTD_NAND_IDS |
| tristate |
| |
| config MTD_NAND_RICOH |
| tristate "Ricoh xD card reader" |
| default n |
| depends on PCI |
| select MTD_SM_COMMON |
| help |
| Enable support for Ricoh R5C852 xD card reader |
| You also need to enable ether |
| NAND SSFDC (SmartMedia) read only translation layer' or new |
| expermental, readwrite |
| 'SmartMedia/xD new translation layer' |
| |
| config MTD_NAND_AU1550 |
| tristate "Au1550/1200 NAND support" |
| depends on MIPS_ALCHEMY |
| help |
| This enables the driver for the NAND flash controller on the |
| AMD/Alchemy 1550 SOC. |
| |
| config MTD_NAND_BF5XX |
| tristate "Blackfin on-chip NAND Flash Controller driver" |
| depends on BF54x || BF52x |
| help |
| This enables the Blackfin on-chip NAND flash controller |
| |
| No board specific support is done by this driver, each board |
| must advertise a platform_device for the driver to attach. |
| |
| This driver can also be built as a module. If so, the module |
| will be called bf5xx-nand. |
| |
| config MTD_NAND_BF5XX_HWECC |
| bool "BF5XX NAND Hardware ECC" |
| default y |
| depends on MTD_NAND_BF5XX |
| help |
| Enable the use of the BF5XX's internal ECC generator when |
| using NAND. |
| |
| config MTD_NAND_BF5XX_BOOTROM_ECC |
| bool "Use Blackfin BootROM ECC Layout" |
| default n |
| depends on MTD_NAND_BF5XX_HWECC |
| help |
| If you wish to modify NAND pages and allow the Blackfin on-chip |
| BootROM to boot from them, say Y here. This is only necessary |
| if you are booting U-Boot out of NAND and you wish to update |
| U-Boot from Linux' userspace. Otherwise, you should say N here. |
| |
| If unsure, say N. |
| |
| config MTD_NAND_S3C2410 |
| tristate "NAND Flash support for Samsung S3C SoCs" |
| depends on ARCH_S3C24XX || ARCH_S3C64XX |
| help |
| This enables the NAND flash controller on the S3C24xx and S3C64xx |
| SoCs |
| |
| No board specific support is done by this driver, each board |
| must advertise a platform_device for the driver to attach. |
| |
| config MTD_NAND_S3C2410_DEBUG |
| bool "Samsung S3C NAND driver debug" |
| depends on MTD_NAND_S3C2410 |
| help |
| Enable debugging of the S3C NAND driver |
| |
| config MTD_NAND_S3C2410_HWECC |
| bool "Samsung S3C NAND Hardware ECC" |
| depends on MTD_NAND_S3C2410 |
| help |
| Enable the use of the controller's internal ECC generator when |
| using NAND. Early versions of the chips have had problems with |
| incorrect ECC generation, and if using these, the default of |
| software ECC is preferable. |
| |
| config MTD_NAND_NDFC |
| tristate "NDFC NanD Flash Controller" |
| depends on 4xx |
| select MTD_NAND_ECC_SMC |
| help |
| NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs |
| |
| config MTD_NAND_S3C2410_CLKSTOP |
| bool "Samsung S3C NAND IDLE clock stop" |
| depends on MTD_NAND_S3C2410 |
| default n |
| help |
| Stop the clock to the NAND controller when there is no chip |
| selected to save power. This will mean there is a small delay |
| when the is NAND chip selected or released, but will save |
| approximately 5mA of power when there is nothing happening. |
| |
| config MTD_NAND_DISKONCHIP |
| tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)" |
| depends on HAS_IOMEM |
| select REED_SOLOMON |
| select REED_SOLOMON_DEC16 |
| help |
| This is a reimplementation of M-Systems DiskOnChip 2000, |
| Millennium and Millennium Plus as a standard NAND device driver, |
| as opposed to the earlier self-contained MTD device drivers. |
| This should enable, among other things, proper JFFS2 operation on |
| these devices. |
| |
| config MTD_NAND_DISKONCHIP_PROBE_ADVANCED |
| bool "Advanced detection options for DiskOnChip" |
| depends on MTD_NAND_DISKONCHIP |
| help |
| This option allows you to specify nonstandard address at which to |
| probe for a DiskOnChip, or to change the detection options. You |
| are unlikely to need any of this unless you are using LinuxBIOS. |
| Say 'N'. |
| |
| config MTD_NAND_DISKONCHIP_PROBE_ADDRESS |
| hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED |
| depends on MTD_NAND_DISKONCHIP |
| default "0" |
| ---help--- |
| By default, the probe for DiskOnChip devices will look for a |
| DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. |
| This option allows you to specify a single address at which to probe |
| for the device, which is useful if you have other devices in that |
| range which get upset when they are probed. |
| |
| (Note that on PowerPC, the normal probe will only check at |
| 0xE4000000.) |
| |
| Normally, you should leave this set to zero, to allow the probe at |
| the normal addresses. |
| |
| config MTD_NAND_DISKONCHIP_PROBE_HIGH |
| bool "Probe high addresses" |
| depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED |
| help |
| By default, the probe for DiskOnChip devices will look for a |
| DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000. |
| This option changes to make it probe between 0xFFFC8000 and |
| 0xFFFEE000. Unless you are using LinuxBIOS, this is unlikely to be |
| useful to you. Say 'N'. |
| |
| config MTD_NAND_DISKONCHIP_BBTWRITE |
| bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP" |
| depends on MTD_NAND_DISKONCHIP |
| help |
| On DiskOnChip devices shipped with the INFTL filesystem (Millennium |
| and 2000 TSOP/Alon), Linux reserves some space at the end of the |
| device for the Bad Block Table (BBT). If you have existing INFTL |
| data on your device (created by non-Linux tools such as M-Systems' |
| DOS drivers), your data might overlap the area Linux wants to use for |
| the BBT. If this is a concern for you, leave this option disabled and |
| Linux will not write BBT data into this area. |
| The downside of leaving this option disabled is that if bad blocks |
| are detected by Linux, they will not be recorded in the BBT, which |
| could cause future problems. |
| Once you enable this option, new filesystems (INFTL or others, created |
| in Linux or other operating systems) will not use the reserved area. |
| The only reason not to enable this option is to prevent damage to |
| preexisting filesystems. |
| Even if you leave this disabled, you can enable BBT writes at module |
| load time (assuming you build diskonchip as a module) with the module |
| parameter "inftl_bbt_write=1". |
| |
| config MTD_NAND_DOCG4 |
| tristate "Support for DiskOnChip G4" |
| depends on HAS_IOMEM |
| select BCH |
| select BITREVERSE |
| help |
| Support for diskonchip G4 nand flash, found in various smartphones and |
| PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba |
| Portege G900, Asus P526, and O2 XDA Zinc. |
| |
| With this driver you will be able to use UBI and create a ubifs on the |
| device, so you may wish to consider enabling UBI and UBIFS as well. |
| |
| These devices ship with the Mys/Sandisk SAFTL formatting, for which |
| there is currently no mtd parser, so you may want to use command line |
| partitioning to segregate write-protected blocks. On the Treo680, the |
| first five erase blocks (256KiB each) are write-protected, followed |
| by the block containing the saftl partition table. This is probably |
| typical. |
| |
| config MTD_NAND_SHARPSL |
| tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)" |
| depends on ARCH_PXA |
| |
| config MTD_NAND_CAFE |
| tristate "NAND support for OLPC CAFÉ chip" |
| depends on PCI |
| select REED_SOLOMON |
| select REED_SOLOMON_DEC16 |
| help |
| Use NAND flash attached to the CAFÉ chip designed for the OLPC |
| laptop. |
| |
| config MTD_NAND_CS553X |
| tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)" |
| depends on X86_32 |
| help |
| The CS553x companion chips for the AMD Geode processor |
| include NAND flash controllers with built-in hardware ECC |
| capabilities; enabling this option will allow you to use |
| these. The driver will check the MSRs to verify that the |
| controller is enabled for NAND, and currently requires that |
| the controller be in MMIO mode. |
| |
| If you say "m", the module will be called cs553x_nand. |
| |
| config MTD_NAND_ATMEL |
| tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32" |
| depends on ARCH_AT91 || AVR32 |
| help |
| Enables support for NAND Flash / Smart Media Card interface |
| on Atmel AT91 and AVR32 processors. |
| |
| config MTD_NAND_PXA3xx |
| tristate "NAND support on PXA3xx and Armada 370/XP" |
| depends on PXA3xx || ARCH_MMP || PLAT_ORION |
| help |
| This enables the driver for the NAND flash device found on |
| PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). |
| |
| config MTD_NAND_SLC_LPC32XX |
| tristate "NXP LPC32xx SLC Controller" |
| depends on ARCH_LPC32XX |
| help |
| Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell |
| chips) NAND controller. This is the default for the PHYTEC 3250 |
| reference board which contains a NAND256R3A2CZA6 chip. |
| |
| Please check the actual NAND chip connected and its support |
| by the SLC NAND controller. |
| |
| config MTD_NAND_MLC_LPC32XX |
| tristate "NXP LPC32xx MLC Controller" |
| depends on ARCH_LPC32XX |
| help |
| Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND |
| controller. This is the default for the WORK92105 controller |
| board. |
| |
| Please check the actual NAND chip connected and its support |
| by the MLC NAND controller. |
| |
| config MTD_NAND_CM_X270 |
| tristate "Support for NAND Flash on CM-X270 modules" |
| depends on MACH_ARMCORE |
| |
| config MTD_NAND_PASEMI |
| tristate "NAND support for PA Semi PWRficient" |
| depends on PPC_PASEMI |
| help |
| Enables support for NAND Flash interface on PA Semi PWRficient |
| based boards |
| |
| config MTD_NAND_TMIO |
| tristate "NAND Flash device on Toshiba Mobile IO Controller" |
| depends on MFD_TMIO |
| help |
| Support for NAND flash connected to a Toshiba Mobile IO |
| Controller in some PDAs, including the Sharp SL6000x. |
| |
| config MTD_NAND_NANDSIM |
| tristate "Support for NAND Flash Simulator" |
| help |
| The simulator may simulate various NAND flash chips for the |
| MTD nand layer. |
| |
| config MTD_NAND_GPMI_NAND |
| tristate "GPMI NAND Flash Controller driver" |
| depends on MTD_NAND && MXS_DMA |
| help |
| Enables NAND Flash support for IMX23, IMX28 or IMX6. |
| The GPMI controller is very powerful, with the help of BCH |
| module, it can do the hardware ECC. The GPMI supports several |
| NAND flashs at the same time. The GPMI may conflicts with other |
| block, such as SD card. So pay attention to it when you enable |
| the GPMI. |
| |
| config MTD_NAND_BCM47XXNFLASH |
| tristate "Support for NAND flash on BCM4706 BCMA bus" |
| depends on BCMA_NFLASH |
| help |
| BCMA bus can have various flash memories attached, they are |
| registered by bcma as platform devices. This enables driver for |
| NAND flash memories. For now only BCM4706 is supported. |
| |
| config MTD_NAND_PLATFORM |
| tristate "Support for generic platform NAND driver" |
| depends on HAS_IOMEM |
| help |
| This implements a generic NAND driver for on-SOC platform |
| devices. You will need to provide platform-specific functions |
| via platform_data. |
| |
| config MTD_NAND_ORION |
| tristate "NAND Flash support for Marvell Orion SoC" |
| depends on PLAT_ORION |
| help |
| This enables the NAND flash controller on Orion machines. |
| |
| No board specific support is done by this driver, each board |
| must advertise a platform_device for the driver to attach. |
| |
| config MTD_NAND_FSL_ELBC |
| tristate "NAND support for Freescale eLBC controllers" |
| depends on PPC_OF |
| select FSL_LBC |
| help |
| Various Freescale chips, including the 8313, include a NAND Flash |
| Controller Module with built-in hardware ECC capabilities. |
| Enabling this option will enable you to use this to control |
| external NAND devices. |
| |
| config MTD_NAND_FSL_IFC |
| tristate "NAND support for Freescale IFC controller" |
| depends on MTD_NAND && FSL_SOC |
| select FSL_IFC |
| select MEMORY |
| help |
| Various Freescale chips e.g P1010, include a NAND Flash machine |
| with built-in hardware ECC capabilities. |
| Enabling this option will enable you to use this to control |
| external NAND devices. |
| |
| config MTD_NAND_FSL_UPM |
| tristate "Support for NAND on Freescale UPM" |
| depends on PPC_83xx || PPC_85xx |
| select FSL_LBC |
| help |
| Enables support for NAND Flash chips wired onto Freescale PowerPC |
| processor localbus with User-Programmable Machine support. |
| |
| config MTD_NAND_MPC5121_NFC |
| tristate "MPC5121 built-in NAND Flash Controller support" |
| depends on PPC_MPC512x |
| help |
| This enables the driver for the NAND flash controller on the |
| MPC5121 SoC. |
| |
| config MTD_NAND_MXC |
| tristate "MXC NAND support" |
| depends on ARCH_MXC |
| help |
| This enables the driver for the NAND flash controller on the |
| MXC processors. |
| |
| config MTD_NAND_SH_FLCTL |
| tristate "Support for NAND on Renesas SuperH FLCTL" |
| depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST |
| depends on HAS_IOMEM |
| depends on HAS_DMA |
| help |
| Several Renesas SuperH CPU has FLCTL. This option enables support |
| for NAND Flash using FLCTL. |
| |
| config MTD_NAND_DAVINCI |
| tristate "Support NAND on DaVinci/Keystone SoC" |
| depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF) |
| help |
| Enable the driver for NAND flash chips on Texas Instruments |
| DaVinci/Keystone processors. |
| |
| config MTD_NAND_TXX9NDFMC |
| tristate "NAND Flash support for TXx9 SoC" |
| depends on SOC_TX4938 || SOC_TX4939 |
| help |
| This enables the NAND flash controller on the TXx9 SoCs. |
| |
| config MTD_NAND_SOCRATES |
| tristate "Support for NAND on Socrates board" |
| depends on SOCRATES |
| help |
| Enables support for NAND Flash chips wired onto Socrates board. |
| |
| config MTD_NAND_NUC900 |
| tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards." |
| depends on ARCH_W90X900 |
| help |
| This enables the driver for the NAND Flash on evaluation board based |
| on w90p910 / NUC9xx. |
| |
| config MTD_NAND_JZ4740 |
| tristate "Support for JZ4740 SoC NAND controller" |
| depends on MACH_JZ4740 |
| help |
| Enables support for NAND Flash on JZ4740 SoC based boards. |
| |
| config MTD_NAND_FSMC |
| tristate "Support for NAND on ST Micros FSMC" |
| depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300 |
| help |
| Enables support for NAND Flash chips on the ST Microelectronics |
| Flexible Static Memory Controller (FSMC) |
| |
| config MTD_NAND_XWAY |
| tristate "Support for NAND on Lantiq XWAY SoC" |
| depends on LANTIQ && SOC_TYPE_XWAY |
| select MTD_NAND_PLATFORM |
| help |
| Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached |
| to the External Bus Unit (EBU). |
| |
| endif # MTD_NAND |