usb: phy: rename all phy drivers to phy-$name-usb.c
this will make sure that we have sensible names
for all phy drivers. Current situation was already
quite bad with too generic names being used.
Signed-off-by: Felipe Balbi <balbi@ti.com>
diff --git a/drivers/usb/phy/phy-fsl-usb.c b/drivers/usb/phy/phy-fsl-usb.c
new file mode 100644
index 0000000..97b9308
--- /dev/null
+++ b/drivers/usb/phy/phy-fsl-usb.c
@@ -0,0 +1,1173 @@
+/*
+ * Copyright (C) 2007,2008 Freescale semiconductor, Inc.
+ *
+ * Author: Li Yang <LeoLi@freescale.com>
+ * Jerry Huang <Chang-Ming.Huang@freescale.com>
+ *
+ * Initialization based on code from Shlomi Gridish.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/proc_fs.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/timer.h>
+#include <linux/usb.h>
+#include <linux/device.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/workqueue.h>
+#include <linux/time.h>
+#include <linux/fsl_devices.h>
+#include <linux/platform_device.h>
+#include <linux/uaccess.h>
+
+#include <asm/unaligned.h>
+
+#include "phy-fsl-usb.h"
+
+#define DRIVER_VERSION "Rev. 1.55"
+#define DRIVER_AUTHOR "Jerry Huang/Li Yang"
+#define DRIVER_DESC "Freescale USB OTG Transceiver Driver"
+#define DRIVER_INFO DRIVER_DESC " " DRIVER_VERSION
+
+static const char driver_name[] = "fsl-usb2-otg";
+
+const pm_message_t otg_suspend_state = {
+ .event = 1,
+};
+
+#define HA_DATA_PULSE
+
+static struct usb_dr_mmap *usb_dr_regs;
+static struct fsl_otg *fsl_otg_dev;
+static int srp_wait_done;
+
+/* FSM timers */
+struct fsl_otg_timer *a_wait_vrise_tmr, *a_wait_bcon_tmr, *a_aidl_bdis_tmr,
+ *b_ase0_brst_tmr, *b_se0_srp_tmr;
+
+/* Driver specific timers */
+struct fsl_otg_timer *b_data_pulse_tmr, *b_vbus_pulse_tmr, *b_srp_fail_tmr,
+ *b_srp_wait_tmr, *a_wait_enum_tmr;
+
+static struct list_head active_timers;
+
+static struct fsl_otg_config fsl_otg_initdata = {
+ .otg_port = 1,
+};
+
+#ifdef CONFIG_PPC32
+static u32 _fsl_readl_be(const unsigned __iomem *p)
+{
+ return in_be32(p);
+}
+
+static u32 _fsl_readl_le(const unsigned __iomem *p)
+{
+ return in_le32(p);
+}
+
+static void _fsl_writel_be(u32 v, unsigned __iomem *p)
+{
+ out_be32(p, v);
+}
+
+static void _fsl_writel_le(u32 v, unsigned __iomem *p)
+{
+ out_le32(p, v);
+}
+
+static u32 (*_fsl_readl)(const unsigned __iomem *p);
+static void (*_fsl_writel)(u32 v, unsigned __iomem *p);
+
+#define fsl_readl(p) (*_fsl_readl)((p))
+#define fsl_writel(v, p) (*_fsl_writel)((v), (p))
+
+#else
+#define fsl_readl(addr) readl(addr)
+#define fsl_writel(val, addr) writel(val, addr)
+#endif /* CONFIG_PPC32 */
+
+/* Routines to access transceiver ULPI registers */
+u8 view_ulpi(u8 addr)
+{
+ u32 temp;
+
+ temp = 0x40000000 | (addr << 16);
+ fsl_writel(temp, &usb_dr_regs->ulpiview);
+ udelay(1000);
+ while (temp & 0x40)
+ temp = fsl_readl(&usb_dr_regs->ulpiview);
+ return (le32_to_cpu(temp) & 0x0000ff00) >> 8;
+}
+
+int write_ulpi(u8 addr, u8 data)
+{
+ u32 temp;
+
+ temp = 0x60000000 | (addr << 16) | data;
+ fsl_writel(temp, &usb_dr_regs->ulpiview);
+ return 0;
+}
+
+/* -------------------------------------------------------------*/
+/* Operations that will be called from OTG Finite State Machine */
+
+/* Charge vbus for vbus pulsing in SRP */
+void fsl_otg_chrg_vbus(int on)
+{
+ u32 tmp;
+
+ tmp = fsl_readl(&usb_dr_regs->otgsc) & ~OTGSC_INTSTS_MASK;
+
+ if (on)
+ /* stop discharging, start charging */
+ tmp = (tmp & ~OTGSC_CTRL_VBUS_DISCHARGE) |
+ OTGSC_CTRL_VBUS_CHARGE;
+ else
+ /* stop charging */
+ tmp &= ~OTGSC_CTRL_VBUS_CHARGE;
+
+ fsl_writel(tmp, &usb_dr_regs->otgsc);
+}
+
+/* Discharge vbus through a resistor to ground */
+void fsl_otg_dischrg_vbus(int on)
+{
+ u32 tmp;
+
+ tmp = fsl_readl(&usb_dr_regs->otgsc) & ~OTGSC_INTSTS_MASK;
+
+ if (on)
+ /* stop charging, start discharging */
+ tmp = (tmp & ~OTGSC_CTRL_VBUS_CHARGE) |
+ OTGSC_CTRL_VBUS_DISCHARGE;
+ else
+ /* stop discharging */
+ tmp &= ~OTGSC_CTRL_VBUS_DISCHARGE;
+
+ fsl_writel(tmp, &usb_dr_regs->otgsc);
+}
+
+/* A-device driver vbus, controlled through PP bit in PORTSC */
+void fsl_otg_drv_vbus(int on)
+{
+ u32 tmp;
+
+ if (on) {
+ tmp = fsl_readl(&usb_dr_regs->portsc) & ~PORTSC_W1C_BITS;
+ fsl_writel(tmp | PORTSC_PORT_POWER, &usb_dr_regs->portsc);
+ } else {
+ tmp = fsl_readl(&usb_dr_regs->portsc) &
+ ~PORTSC_W1C_BITS & ~PORTSC_PORT_POWER;
+ fsl_writel(tmp, &usb_dr_regs->portsc);
+ }
+}
+
+/*
+ * Pull-up D+, signalling connect by periperal. Also used in
+ * data-line pulsing in SRP
+ */
+void fsl_otg_loc_conn(int on)
+{
+ u32 tmp;
+
+ tmp = fsl_readl(&usb_dr_regs->otgsc) & ~OTGSC_INTSTS_MASK;
+
+ if (on)
+ tmp |= OTGSC_CTRL_DATA_PULSING;
+ else
+ tmp &= ~OTGSC_CTRL_DATA_PULSING;
+
+ fsl_writel(tmp, &usb_dr_regs->otgsc);
+}
+
+/*
+ * Generate SOF by host. This is controlled through suspend/resume the
+ * port. In host mode, controller will automatically send SOF.
+ * Suspend will block the data on the port.
+ */
+void fsl_otg_loc_sof(int on)
+{
+ u32 tmp;
+
+ tmp = fsl_readl(&fsl_otg_dev->dr_mem_map->portsc) & ~PORTSC_W1C_BITS;
+ if (on)
+ tmp |= PORTSC_PORT_FORCE_RESUME;
+ else
+ tmp |= PORTSC_PORT_SUSPEND;
+
+ fsl_writel(tmp, &fsl_otg_dev->dr_mem_map->portsc);
+
+}
+
+/* Start SRP pulsing by data-line pulsing, followed with v-bus pulsing. */
+void fsl_otg_start_pulse(void)
+{
+ u32 tmp;
+
+ srp_wait_done = 0;
+#ifdef HA_DATA_PULSE
+ tmp = fsl_readl(&usb_dr_regs->otgsc) & ~OTGSC_INTSTS_MASK;
+ tmp |= OTGSC_HA_DATA_PULSE;
+ fsl_writel(tmp, &usb_dr_regs->otgsc);
+#else
+ fsl_otg_loc_conn(1);
+#endif
+
+ fsl_otg_add_timer(b_data_pulse_tmr);
+}
+
+void b_data_pulse_end(unsigned long foo)
+{
+#ifdef HA_DATA_PULSE
+#else
+ fsl_otg_loc_conn(0);
+#endif
+
+ /* Do VBUS pulse after data pulse */
+ fsl_otg_pulse_vbus();
+}
+
+void fsl_otg_pulse_vbus(void)
+{
+ srp_wait_done = 0;
+ fsl_otg_chrg_vbus(1);
+ /* start the timer to end vbus charge */
+ fsl_otg_add_timer(b_vbus_pulse_tmr);
+}
+
+void b_vbus_pulse_end(unsigned long foo)
+{
+ fsl_otg_chrg_vbus(0);
+
+ /*
+ * As USB3300 using the same a_sess_vld and b_sess_vld voltage
+ * we need to discharge the bus for a while to distinguish
+ * residual voltage of vbus pulsing and A device pull up
+ */
+ fsl_otg_dischrg_vbus(1);
+ fsl_otg_add_timer(b_srp_wait_tmr);
+}
+
+void b_srp_end(unsigned long foo)
+{
+ fsl_otg_dischrg_vbus(0);
+ srp_wait_done = 1;
+
+ if ((fsl_otg_dev->phy.state == OTG_STATE_B_SRP_INIT) &&
+ fsl_otg_dev->fsm.b_sess_vld)
+ fsl_otg_dev->fsm.b_srp_done = 1;
+}
+
+/*
+ * Workaround for a_host suspending too fast. When a_bus_req=0,
+ * a_host will start by SRP. It needs to set b_hnp_enable before
+ * actually suspending to start HNP
+ */
+void a_wait_enum(unsigned long foo)
+{
+ VDBG("a_wait_enum timeout\n");
+ if (!fsl_otg_dev->phy.otg->host->b_hnp_enable)
+ fsl_otg_add_timer(a_wait_enum_tmr);
+ else
+ otg_statemachine(&fsl_otg_dev->fsm);
+}
+
+/* The timeout callback function to set time out bit */
+void set_tmout(unsigned long indicator)
+{
+ *(int *)indicator = 1;
+}
+
+/* Initialize timers */
+int fsl_otg_init_timers(struct otg_fsm *fsm)
+{
+ /* FSM used timers */
+ a_wait_vrise_tmr = otg_timer_initializer(&set_tmout, TA_WAIT_VRISE,
+ (unsigned long)&fsm->a_wait_vrise_tmout);
+ if (!a_wait_vrise_tmr)
+ return -ENOMEM;
+
+ a_wait_bcon_tmr = otg_timer_initializer(&set_tmout, TA_WAIT_BCON,
+ (unsigned long)&fsm->a_wait_bcon_tmout);
+ if (!a_wait_bcon_tmr)
+ return -ENOMEM;
+
+ a_aidl_bdis_tmr = otg_timer_initializer(&set_tmout, TA_AIDL_BDIS,
+ (unsigned long)&fsm->a_aidl_bdis_tmout);
+ if (!a_aidl_bdis_tmr)
+ return -ENOMEM;
+
+ b_ase0_brst_tmr = otg_timer_initializer(&set_tmout, TB_ASE0_BRST,
+ (unsigned long)&fsm->b_ase0_brst_tmout);
+ if (!b_ase0_brst_tmr)
+ return -ENOMEM;
+
+ b_se0_srp_tmr = otg_timer_initializer(&set_tmout, TB_SE0_SRP,
+ (unsigned long)&fsm->b_se0_srp);
+ if (!b_se0_srp_tmr)
+ return -ENOMEM;
+
+ b_srp_fail_tmr = otg_timer_initializer(&set_tmout, TB_SRP_FAIL,
+ (unsigned long)&fsm->b_srp_done);
+ if (!b_srp_fail_tmr)
+ return -ENOMEM;
+
+ a_wait_enum_tmr = otg_timer_initializer(&a_wait_enum, 10,
+ (unsigned long)&fsm);
+ if (!a_wait_enum_tmr)
+ return -ENOMEM;
+
+ /* device driver used timers */
+ b_srp_wait_tmr = otg_timer_initializer(&b_srp_end, TB_SRP_WAIT, 0);
+ if (!b_srp_wait_tmr)
+ return -ENOMEM;
+
+ b_data_pulse_tmr = otg_timer_initializer(&b_data_pulse_end,
+ TB_DATA_PLS, 0);
+ if (!b_data_pulse_tmr)
+ return -ENOMEM;
+
+ b_vbus_pulse_tmr = otg_timer_initializer(&b_vbus_pulse_end,
+ TB_VBUS_PLS, 0);
+ if (!b_vbus_pulse_tmr)
+ return -ENOMEM;
+
+ return 0;
+}
+
+/* Uninitialize timers */
+void fsl_otg_uninit_timers(void)
+{
+ /* FSM used timers */
+ kfree(a_wait_vrise_tmr);
+ kfree(a_wait_bcon_tmr);
+ kfree(a_aidl_bdis_tmr);
+ kfree(b_ase0_brst_tmr);
+ kfree(b_se0_srp_tmr);
+ kfree(b_srp_fail_tmr);
+ kfree(a_wait_enum_tmr);
+
+ /* device driver used timers */
+ kfree(b_srp_wait_tmr);
+ kfree(b_data_pulse_tmr);
+ kfree(b_vbus_pulse_tmr);
+}
+
+/* Add timer to timer list */
+void fsl_otg_add_timer(void *gtimer)
+{
+ struct fsl_otg_timer *timer = gtimer;
+ struct fsl_otg_timer *tmp_timer;
+
+ /*
+ * Check if the timer is already in the active list,
+ * if so update timer count
+ */
+ list_for_each_entry(tmp_timer, &active_timers, list)
+ if (tmp_timer == timer) {
+ timer->count = timer->expires;
+ return;
+ }
+ timer->count = timer->expires;
+ list_add_tail(&timer->list, &active_timers);
+}
+
+/* Remove timer from the timer list; clear timeout status */
+void fsl_otg_del_timer(void *gtimer)
+{
+ struct fsl_otg_timer *timer = gtimer;
+ struct fsl_otg_timer *tmp_timer, *del_tmp;
+
+ list_for_each_entry_safe(tmp_timer, del_tmp, &active_timers, list)
+ if (tmp_timer == timer)
+ list_del(&timer->list);
+}
+
+/*
+ * Reduce timer count by 1, and find timeout conditions.
+ * Called by fsl_otg 1ms timer interrupt
+ */
+int fsl_otg_tick_timer(void)
+{
+ struct fsl_otg_timer *tmp_timer, *del_tmp;
+ int expired = 0;
+
+ list_for_each_entry_safe(tmp_timer, del_tmp, &active_timers, list) {
+ tmp_timer->count--;
+ /* check if timer expires */
+ if (!tmp_timer->count) {
+ list_del(&tmp_timer->list);
+ tmp_timer->function(tmp_timer->data);
+ expired = 1;
+ }
+ }
+
+ return expired;
+}
+
+/* Reset controller, not reset the bus */
+void otg_reset_controller(void)
+{
+ u32 command;
+
+ command = fsl_readl(&usb_dr_regs->usbcmd);
+ command |= (1 << 1);
+ fsl_writel(command, &usb_dr_regs->usbcmd);
+ while (fsl_readl(&usb_dr_regs->usbcmd) & (1 << 1))
+ ;
+}
+
+/* Call suspend/resume routines in host driver */
+int fsl_otg_start_host(struct otg_fsm *fsm, int on)
+{
+ struct usb_otg *otg = fsm->otg;
+ struct device *dev;
+ struct fsl_otg *otg_dev = container_of(otg->phy, struct fsl_otg, phy);
+ u32 retval = 0;
+
+ if (!otg->host)
+ return -ENODEV;
+ dev = otg->host->controller;
+
+ /*
+ * Update a_vbus_vld state as a_vbus_vld int is disabled
+ * in device mode
+ */
+ fsm->a_vbus_vld =
+ !!(fsl_readl(&usb_dr_regs->otgsc) & OTGSC_STS_A_VBUS_VALID);
+ if (on) {
+ /* start fsl usb host controller */
+ if (otg_dev->host_working)
+ goto end;
+ else {
+ otg_reset_controller();
+ VDBG("host on......\n");
+ if (dev->driver->pm && dev->driver->pm->resume) {
+ retval = dev->driver->pm->resume(dev);
+ if (fsm->id) {
+ /* default-b */
+ fsl_otg_drv_vbus(1);
+ /*
+ * Workaround: b_host can't driver
+ * vbus, but PP in PORTSC needs to
+ * be 1 for host to work.
+ * So we set drv_vbus bit in
+ * transceiver to 0 thru ULPI.
+ */
+ write_ulpi(0x0c, 0x20);
+ }
+ }
+
+ otg_dev->host_working = 1;
+ }
+ } else {
+ /* stop fsl usb host controller */
+ if (!otg_dev->host_working)
+ goto end;
+ else {
+ VDBG("host off......\n");
+ if (dev && dev->driver) {
+ if (dev->driver->pm && dev->driver->pm->suspend)
+ retval = dev->driver->pm->suspend(dev);
+ if (fsm->id)
+ /* default-b */
+ fsl_otg_drv_vbus(0);
+ }
+ otg_dev->host_working = 0;
+ }
+ }
+end:
+ return retval;
+}
+
+/*
+ * Call suspend and resume function in udc driver
+ * to stop and start udc driver.
+ */
+int fsl_otg_start_gadget(struct otg_fsm *fsm, int on)
+{
+ struct usb_otg *otg = fsm->otg;
+ struct device *dev;
+
+ if (!otg->gadget || !otg->gadget->dev.parent)
+ return -ENODEV;
+
+ VDBG("gadget %s\n", on ? "on" : "off");
+ dev = otg->gadget->dev.parent;
+
+ if (on) {
+ if (dev->driver->resume)
+ dev->driver->resume(dev);
+ } else {
+ if (dev->driver->suspend)
+ dev->driver->suspend(dev, otg_suspend_state);
+ }
+
+ return 0;
+}
+
+/*
+ * Called by initialization code of host driver. Register host controller
+ * to the OTG. Suspend host for OTG role detection.
+ */
+static int fsl_otg_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+ struct fsl_otg *otg_dev;
+
+ if (!otg)
+ return -ENODEV;
+
+ otg_dev = container_of(otg->phy, struct fsl_otg, phy);
+ if (otg_dev != fsl_otg_dev)
+ return -ENODEV;
+
+ otg->host = host;
+
+ otg_dev->fsm.a_bus_drop = 0;
+ otg_dev->fsm.a_bus_req = 1;
+
+ if (host) {
+ VDBG("host off......\n");
+
+ otg->host->otg_port = fsl_otg_initdata.otg_port;
+ otg->host->is_b_host = otg_dev->fsm.id;
+ /*
+ * must leave time for khubd to finish its thing
+ * before yanking the host driver out from under it,
+ * so suspend the host after a short delay.
+ */
+ otg_dev->host_working = 1;
+ schedule_delayed_work(&otg_dev->otg_event, 100);
+ return 0;
+ } else {
+ /* host driver going away */
+ if (!(fsl_readl(&otg_dev->dr_mem_map->otgsc) &
+ OTGSC_STS_USB_ID)) {
+ /* Mini-A cable connected */
+ struct otg_fsm *fsm = &otg_dev->fsm;
+
+ otg->phy->state = OTG_STATE_UNDEFINED;
+ fsm->protocol = PROTO_UNDEF;
+ }
+ }
+
+ otg_dev->host_working = 0;
+
+ otg_statemachine(&otg_dev->fsm);
+
+ return 0;
+}
+
+/* Called by initialization code of udc. Register udc to OTG. */
+static int fsl_otg_set_peripheral(struct usb_otg *otg,
+ struct usb_gadget *gadget)
+{
+ struct fsl_otg *otg_dev;
+
+ if (!otg)
+ return -ENODEV;
+
+ otg_dev = container_of(otg->phy, struct fsl_otg, phy);
+ VDBG("otg_dev 0x%x\n", (int)otg_dev);
+ VDBG("fsl_otg_dev 0x%x\n", (int)fsl_otg_dev);
+ if (otg_dev != fsl_otg_dev)
+ return -ENODEV;
+
+ if (!gadget) {
+ if (!otg->default_a)
+ otg->gadget->ops->vbus_draw(otg->gadget, 0);
+ usb_gadget_vbus_disconnect(otg->gadget);
+ otg->gadget = 0;
+ otg_dev->fsm.b_bus_req = 0;
+ otg_statemachine(&otg_dev->fsm);
+ return 0;
+ }
+
+ otg->gadget = gadget;
+ otg->gadget->is_a_peripheral = !otg_dev->fsm.id;
+
+ otg_dev->fsm.b_bus_req = 1;
+
+ /* start the gadget right away if the ID pin says Mini-B */
+ DBG("ID pin=%d\n", otg_dev->fsm.id);
+ if (otg_dev->fsm.id == 1) {
+ fsl_otg_start_host(&otg_dev->fsm, 0);
+ otg_drv_vbus(&otg_dev->fsm, 0);
+ fsl_otg_start_gadget(&otg_dev->fsm, 1);
+ }
+
+ return 0;
+}
+
+/* Set OTG port power, only for B-device */
+static int fsl_otg_set_power(struct usb_phy *phy, unsigned mA)
+{
+ if (!fsl_otg_dev)
+ return -ENODEV;
+ if (phy->state == OTG_STATE_B_PERIPHERAL)
+ pr_info("FSL OTG: Draw %d mA\n", mA);
+
+ return 0;
+}
+
+/*
+ * Delayed pin detect interrupt processing.
+ *
+ * When the Mini-A cable is disconnected from the board,
+ * the pin-detect interrupt happens before the disconnect
+ * interrupts for the connected device(s). In order to
+ * process the disconnect interrupt(s) prior to switching
+ * roles, the pin-detect interrupts are delayed, and handled
+ * by this routine.
+ */
+static void fsl_otg_event(struct work_struct *work)
+{
+ struct fsl_otg *og = container_of(work, struct fsl_otg, otg_event.work);
+ struct otg_fsm *fsm = &og->fsm;
+
+ if (fsm->id) { /* switch to gadget */
+ fsl_otg_start_host(fsm, 0);
+ otg_drv_vbus(fsm, 0);
+ fsl_otg_start_gadget(fsm, 1);
+ }
+}
+
+/* B-device start SRP */
+static int fsl_otg_start_srp(struct usb_otg *otg)
+{
+ struct fsl_otg *otg_dev;
+
+ if (!otg || otg->phy->state != OTG_STATE_B_IDLE)
+ return -ENODEV;
+
+ otg_dev = container_of(otg->phy, struct fsl_otg, phy);
+ if (otg_dev != fsl_otg_dev)
+ return -ENODEV;
+
+ otg_dev->fsm.b_bus_req = 1;
+ otg_statemachine(&otg_dev->fsm);
+
+ return 0;
+}
+
+/* A_host suspend will call this function to start hnp */
+static int fsl_otg_start_hnp(struct usb_otg *otg)
+{
+ struct fsl_otg *otg_dev;
+
+ if (!otg)
+ return -ENODEV;
+
+ otg_dev = container_of(otg->phy, struct fsl_otg, phy);
+ if (otg_dev != fsl_otg_dev)
+ return -ENODEV;
+
+ DBG("start_hnp...n");
+
+ /* clear a_bus_req to enter a_suspend state */
+ otg_dev->fsm.a_bus_req = 0;
+ otg_statemachine(&otg_dev->fsm);
+
+ return 0;
+}
+
+/*
+ * Interrupt handler. OTG/host/peripheral share the same int line.
+ * OTG driver clears OTGSC interrupts and leaves USB interrupts
+ * intact. It needs to have knowledge of some USB interrupts
+ * such as port change.
+ */
+irqreturn_t fsl_otg_isr(int irq, void *dev_id)
+{
+ struct otg_fsm *fsm = &((struct fsl_otg *)dev_id)->fsm;
+ struct usb_otg *otg = ((struct fsl_otg *)dev_id)->phy.otg;
+ u32 otg_int_src, otg_sc;
+
+ otg_sc = fsl_readl(&usb_dr_regs->otgsc);
+ otg_int_src = otg_sc & OTGSC_INTSTS_MASK & (otg_sc >> 8);
+
+ /* Only clear otg interrupts */
+ fsl_writel(otg_sc, &usb_dr_regs->otgsc);
+
+ /*FIXME: ID change not generate when init to 0 */
+ fsm->id = (otg_sc & OTGSC_STS_USB_ID) ? 1 : 0;
+ otg->default_a = (fsm->id == 0);
+
+ /* process OTG interrupts */
+ if (otg_int_src) {
+ if (otg_int_src & OTGSC_INTSTS_USB_ID) {
+ fsm->id = (otg_sc & OTGSC_STS_USB_ID) ? 1 : 0;
+ otg->default_a = (fsm->id == 0);
+ /* clear conn information */
+ if (fsm->id)
+ fsm->b_conn = 0;
+ else
+ fsm->a_conn = 0;
+
+ if (otg->host)
+ otg->host->is_b_host = fsm->id;
+ if (otg->gadget)
+ otg->gadget->is_a_peripheral = !fsm->id;
+ VDBG("ID int (ID is %d)\n", fsm->id);
+
+ if (fsm->id) { /* switch to gadget */
+ schedule_delayed_work(
+ &((struct fsl_otg *)dev_id)->otg_event,
+ 100);
+ } else { /* switch to host */
+ cancel_delayed_work(&
+ ((struct fsl_otg *)dev_id)->
+ otg_event);
+ fsl_otg_start_gadget(fsm, 0);
+ otg_drv_vbus(fsm, 1);
+ fsl_otg_start_host(fsm, 1);
+ }
+ return IRQ_HANDLED;
+ }
+ }
+ return IRQ_NONE;
+}
+
+static struct otg_fsm_ops fsl_otg_ops = {
+ .chrg_vbus = fsl_otg_chrg_vbus,
+ .drv_vbus = fsl_otg_drv_vbus,
+ .loc_conn = fsl_otg_loc_conn,
+ .loc_sof = fsl_otg_loc_sof,
+ .start_pulse = fsl_otg_start_pulse,
+
+ .add_timer = fsl_otg_add_timer,
+ .del_timer = fsl_otg_del_timer,
+
+ .start_host = fsl_otg_start_host,
+ .start_gadget = fsl_otg_start_gadget,
+};
+
+/* Initialize the global variable fsl_otg_dev and request IRQ for OTG */
+static int fsl_otg_conf(struct platform_device *pdev)
+{
+ struct fsl_otg *fsl_otg_tc;
+ int status;
+
+ if (fsl_otg_dev)
+ return 0;
+
+ /* allocate space to fsl otg device */
+ fsl_otg_tc = kzalloc(sizeof(struct fsl_otg), GFP_KERNEL);
+ if (!fsl_otg_tc)
+ return -ENOMEM;
+
+ fsl_otg_tc->phy.otg = kzalloc(sizeof(struct usb_otg), GFP_KERNEL);
+ if (!fsl_otg_tc->phy.otg) {
+ kfree(fsl_otg_tc);
+ return -ENOMEM;
+ }
+
+ INIT_DELAYED_WORK(&fsl_otg_tc->otg_event, fsl_otg_event);
+
+ INIT_LIST_HEAD(&active_timers);
+ status = fsl_otg_init_timers(&fsl_otg_tc->fsm);
+ if (status) {
+ pr_info("Couldn't init OTG timers\n");
+ goto err;
+ }
+ spin_lock_init(&fsl_otg_tc->fsm.lock);
+
+ /* Set OTG state machine operations */
+ fsl_otg_tc->fsm.ops = &fsl_otg_ops;
+
+ /* initialize the otg structure */
+ fsl_otg_tc->phy.label = DRIVER_DESC;
+ fsl_otg_tc->phy.set_power = fsl_otg_set_power;
+
+ fsl_otg_tc->phy.otg->phy = &fsl_otg_tc->phy;
+ fsl_otg_tc->phy.otg->set_host = fsl_otg_set_host;
+ fsl_otg_tc->phy.otg->set_peripheral = fsl_otg_set_peripheral;
+ fsl_otg_tc->phy.otg->start_hnp = fsl_otg_start_hnp;
+ fsl_otg_tc->phy.otg->start_srp = fsl_otg_start_srp;
+
+ fsl_otg_dev = fsl_otg_tc;
+
+ /* Store the otg transceiver */
+ status = usb_add_phy(&fsl_otg_tc->phy, USB_PHY_TYPE_USB2);
+ if (status) {
+ pr_warn(FSL_OTG_NAME ": unable to register OTG transceiver.\n");
+ goto err;
+ }
+
+ return 0;
+err:
+ fsl_otg_uninit_timers();
+ kfree(fsl_otg_tc->phy.otg);
+ kfree(fsl_otg_tc);
+ return status;
+}
+
+/* OTG Initialization */
+int usb_otg_start(struct platform_device *pdev)
+{
+ struct fsl_otg *p_otg;
+ struct usb_phy *otg_trans = usb_get_phy(USB_PHY_TYPE_USB2);
+ struct otg_fsm *fsm;
+ int status;
+ struct resource *res;
+ u32 temp;
+ struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
+
+ p_otg = container_of(otg_trans, struct fsl_otg, phy);
+ fsm = &p_otg->fsm;
+
+ /* Initialize the state machine structure with default values */
+ SET_OTG_STATE(otg_trans, OTG_STATE_UNDEFINED);
+ fsm->otg = p_otg->phy.otg;
+
+ /* We don't require predefined MEM/IRQ resource index */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENXIO;
+
+ /* We don't request_mem_region here to enable resource sharing
+ * with host/device */
+
+ usb_dr_regs = ioremap(res->start, sizeof(struct usb_dr_mmap));
+ p_otg->dr_mem_map = (struct usb_dr_mmap *)usb_dr_regs;
+ pdata->regs = (void *)usb_dr_regs;
+
+ if (pdata->init && pdata->init(pdev) != 0)
+ return -EINVAL;
+
+ if (pdata->big_endian_mmio) {
+ _fsl_readl = _fsl_readl_be;
+ _fsl_writel = _fsl_writel_be;
+ } else {
+ _fsl_readl = _fsl_readl_le;
+ _fsl_writel = _fsl_writel_le;
+ }
+
+ /* request irq */
+ p_otg->irq = platform_get_irq(pdev, 0);
+ status = request_irq(p_otg->irq, fsl_otg_isr,
+ IRQF_SHARED, driver_name, p_otg);
+ if (status) {
+ dev_dbg(p_otg->phy.dev, "can't get IRQ %d, error %d\n",
+ p_otg->irq, status);
+ iounmap(p_otg->dr_mem_map);
+ kfree(p_otg->phy.otg);
+ kfree(p_otg);
+ return status;
+ }
+
+ /* stop the controller */
+ temp = fsl_readl(&p_otg->dr_mem_map->usbcmd);
+ temp &= ~USB_CMD_RUN_STOP;
+ fsl_writel(temp, &p_otg->dr_mem_map->usbcmd);
+
+ /* reset the controller */
+ temp = fsl_readl(&p_otg->dr_mem_map->usbcmd);
+ temp |= USB_CMD_CTRL_RESET;
+ fsl_writel(temp, &p_otg->dr_mem_map->usbcmd);
+
+ /* wait reset completed */
+ while (fsl_readl(&p_otg->dr_mem_map->usbcmd) & USB_CMD_CTRL_RESET)
+ ;
+
+ /* configure the VBUSHS as IDLE(both host and device) */
+ temp = USB_MODE_STREAM_DISABLE | (pdata->es ? USB_MODE_ES : 0);
+ fsl_writel(temp, &p_otg->dr_mem_map->usbmode);
+
+ /* configure PHY interface */
+ temp = fsl_readl(&p_otg->dr_mem_map->portsc);
+ temp &= ~(PORTSC_PHY_TYPE_SEL | PORTSC_PTW);
+ switch (pdata->phy_mode) {
+ case FSL_USB2_PHY_ULPI:
+ temp |= PORTSC_PTS_ULPI;
+ break;
+ case FSL_USB2_PHY_UTMI_WIDE:
+ temp |= PORTSC_PTW_16BIT;
+ /* fall through */
+ case FSL_USB2_PHY_UTMI:
+ temp |= PORTSC_PTS_UTMI;
+ /* fall through */
+ default:
+ break;
+ }
+ fsl_writel(temp, &p_otg->dr_mem_map->portsc);
+
+ if (pdata->have_sysif_regs) {
+ /* configure control enable IO output, big endian register */
+ temp = __raw_readl(&p_otg->dr_mem_map->control);
+ temp |= USB_CTRL_IOENB;
+ __raw_writel(temp, &p_otg->dr_mem_map->control);
+ }
+
+ /* disable all interrupt and clear all OTGSC status */
+ temp = fsl_readl(&p_otg->dr_mem_map->otgsc);
+ temp &= ~OTGSC_INTERRUPT_ENABLE_BITS_MASK;
+ temp |= OTGSC_INTERRUPT_STATUS_BITS_MASK | OTGSC_CTRL_VBUS_DISCHARGE;
+ fsl_writel(temp, &p_otg->dr_mem_map->otgsc);
+
+ /*
+ * The identification (id) input is FALSE when a Mini-A plug is inserted
+ * in the devices Mini-AB receptacle. Otherwise, this input is TRUE.
+ * Also: record initial state of ID pin
+ */
+ if (fsl_readl(&p_otg->dr_mem_map->otgsc) & OTGSC_STS_USB_ID) {
+ p_otg->phy.state = OTG_STATE_UNDEFINED;
+ p_otg->fsm.id = 1;
+ } else {
+ p_otg->phy.state = OTG_STATE_A_IDLE;
+ p_otg->fsm.id = 0;
+ }
+
+ DBG("initial ID pin=%d\n", p_otg->fsm.id);
+
+ /* enable OTG ID pin interrupt */
+ temp = fsl_readl(&p_otg->dr_mem_map->otgsc);
+ temp |= OTGSC_INTR_USB_ID_EN;
+ temp &= ~(OTGSC_CTRL_VBUS_DISCHARGE | OTGSC_INTR_1MS_TIMER_EN);
+ fsl_writel(temp, &p_otg->dr_mem_map->otgsc);
+
+ return 0;
+}
+
+/*
+ * state file in sysfs
+ */
+static int show_fsl_usb2_otg_state(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct otg_fsm *fsm = &fsl_otg_dev->fsm;
+ char *next = buf;
+ unsigned size = PAGE_SIZE;
+ unsigned long flags;
+ int t;
+
+ spin_lock_irqsave(&fsm->lock, flags);
+
+ /* basic driver infomation */
+ t = scnprintf(next, size,
+ DRIVER_DESC "\n" "fsl_usb2_otg version: %s\n\n",
+ DRIVER_VERSION);
+ size -= t;
+ next += t;
+
+ /* Registers */
+ t = scnprintf(next, size,
+ "OTGSC: 0x%08x\n"
+ "PORTSC: 0x%08x\n"
+ "USBMODE: 0x%08x\n"
+ "USBCMD: 0x%08x\n"
+ "USBSTS: 0x%08x\n"
+ "USBINTR: 0x%08x\n",
+ fsl_readl(&usb_dr_regs->otgsc),
+ fsl_readl(&usb_dr_regs->portsc),
+ fsl_readl(&usb_dr_regs->usbmode),
+ fsl_readl(&usb_dr_regs->usbcmd),
+ fsl_readl(&usb_dr_regs->usbsts),
+ fsl_readl(&usb_dr_regs->usbintr));
+ size -= t;
+ next += t;
+
+ /* State */
+ t = scnprintf(next, size,
+ "OTG state: %s\n\n",
+ usb_otg_state_string(fsl_otg_dev->phy.state));
+ size -= t;
+ next += t;
+
+ /* State Machine Variables */
+ t = scnprintf(next, size,
+ "a_bus_req: %d\n"
+ "b_bus_req: %d\n"
+ "a_bus_resume: %d\n"
+ "a_bus_suspend: %d\n"
+ "a_conn: %d\n"
+ "a_sess_vld: %d\n"
+ "a_srp_det: %d\n"
+ "a_vbus_vld: %d\n"
+ "b_bus_resume: %d\n"
+ "b_bus_suspend: %d\n"
+ "b_conn: %d\n"
+ "b_se0_srp: %d\n"
+ "b_sess_end: %d\n"
+ "b_sess_vld: %d\n"
+ "id: %d\n",
+ fsm->a_bus_req,
+ fsm->b_bus_req,
+ fsm->a_bus_resume,
+ fsm->a_bus_suspend,
+ fsm->a_conn,
+ fsm->a_sess_vld,
+ fsm->a_srp_det,
+ fsm->a_vbus_vld,
+ fsm->b_bus_resume,
+ fsm->b_bus_suspend,
+ fsm->b_conn,
+ fsm->b_se0_srp,
+ fsm->b_sess_end,
+ fsm->b_sess_vld,
+ fsm->id);
+ size -= t;
+ next += t;
+
+ spin_unlock_irqrestore(&fsm->lock, flags);
+
+ return PAGE_SIZE - size;
+}
+
+static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
+
+
+/* Char driver interface to control some OTG input */
+
+/*
+ * Handle some ioctl command, such as get otg
+ * status and set host suspend
+ */
+static long fsl_otg_ioctl(struct file *file, unsigned int cmd,
+ unsigned long arg)
+{
+ u32 retval = 0;
+
+ switch (cmd) {
+ case GET_OTG_STATUS:
+ retval = fsl_otg_dev->host_working;
+ break;
+
+ case SET_A_SUSPEND_REQ:
+ fsl_otg_dev->fsm.a_suspend_req = arg;
+ break;
+
+ case SET_A_BUS_DROP:
+ fsl_otg_dev->fsm.a_bus_drop = arg;
+ break;
+
+ case SET_A_BUS_REQ:
+ fsl_otg_dev->fsm.a_bus_req = arg;
+ break;
+
+ case SET_B_BUS_REQ:
+ fsl_otg_dev->fsm.b_bus_req = arg;
+ break;
+
+ default:
+ break;
+ }
+
+ otg_statemachine(&fsl_otg_dev->fsm);
+
+ return retval;
+}
+
+static int fsl_otg_open(struct inode *inode, struct file *file)
+{
+ return 0;
+}
+
+static int fsl_otg_release(struct inode *inode, struct file *file)
+{
+ return 0;
+}
+
+static const struct file_operations otg_fops = {
+ .owner = THIS_MODULE,
+ .llseek = NULL,
+ .read = NULL,
+ .write = NULL,
+ .unlocked_ioctl = fsl_otg_ioctl,
+ .open = fsl_otg_open,
+ .release = fsl_otg_release,
+};
+
+static int fsl_otg_probe(struct platform_device *pdev)
+{
+ int ret;
+
+ if (!pdev->dev.platform_data)
+ return -ENODEV;
+
+ /* configure the OTG */
+ ret = fsl_otg_conf(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Couldn't configure OTG module\n");
+ return ret;
+ }
+
+ /* start OTG */
+ ret = usb_otg_start(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't init FSL OTG device\n");
+ return ret;
+ }
+
+ ret = register_chrdev(FSL_OTG_MAJOR, FSL_OTG_NAME, &otg_fops);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to register FSL OTG device\n");
+ return ret;
+ }
+
+ ret = device_create_file(&pdev->dev, &dev_attr_fsl_usb2_otg_state);
+ if (ret)
+ dev_warn(&pdev->dev, "Can't register sysfs attribute\n");
+
+ return ret;
+}
+
+static int fsl_otg_remove(struct platform_device *pdev)
+{
+ struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
+
+ usb_remove_phy(&fsl_otg_dev->phy);
+ free_irq(fsl_otg_dev->irq, fsl_otg_dev);
+
+ iounmap((void *)usb_dr_regs);
+
+ fsl_otg_uninit_timers();
+ kfree(fsl_otg_dev->phy.otg);
+ kfree(fsl_otg_dev);
+
+ device_remove_file(&pdev->dev, &dev_attr_fsl_usb2_otg_state);
+
+ unregister_chrdev(FSL_OTG_MAJOR, FSL_OTG_NAME);
+
+ if (pdata->exit)
+ pdata->exit(pdev);
+
+ return 0;
+}
+
+struct platform_driver fsl_otg_driver = {
+ .probe = fsl_otg_probe,
+ .remove = fsl_otg_remove,
+ .driver = {
+ .name = driver_name,
+ .owner = THIS_MODULE,
+ },
+};
+
+module_platform_driver(fsl_otg_driver);
+
+MODULE_DESCRIPTION(DRIVER_INFO);
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_LICENSE("GPL");