arch/arm/mach-s3c2410/mach-n30.c - kernel/msm-4.9 - Gitiles

 /* Machine specific code for the Acer n30, Acer N35, Navman PiN 570,
  * Yakumo AlphaX and Airis NC05 PDAs.
  *
  * Copyright (c) 2003-2005 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>
  *
  * Copyright (c) 2005-2008 Christer Weinigel <christer@weinigel.se>
  *
  * There is a wiki with more information about the n30 port at
  * http://handhelds.org/moin/moin.cgi/AcerN30Documentation .
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */

 #include <linux/kernel.h>
 #include <linux/types.h>

 #include <linux/delay.h>
 #include <linux/gpio_keys.h>
 #include <linux/init.h>
 #include <linux/input.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
 #include <linux/serial_core.h>
 #include <linux/timer.h>

 #include <asm/hardware.h>
 #include <asm/io.h>
 #include <asm/irq.h>
 #include <asm/mach-types.h>

 #include <asm/arch/leds-gpio.h>
 #include <asm/arch/regs-gpio.h>

 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/map.h>

 #include <asm/plat-s3c/iic.h>
 #include <asm/plat-s3c/regs-serial.h>

 #include <asm/plat-s3c24xx/clock.h>
 #include <asm/plat-s3c24xx/cpu.h>
 #include <asm/plat-s3c24xx/devs.h>
 #include <asm/plat-s3c24xx/s3c2410.h>
 #include <asm/plat-s3c24xx/udc.h>

 static struct map_desc n30_iodesc[] __initdata = {
 	/* nothing here yet */
 };

 static struct s3c2410_uartcfg n30_uartcfgs[] = {
 	/* Normal serial port */
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
 		.ucon	     = 0x2c5,
 		.ulcon	     = 0x03,
 		.ufcon	     = 0x51,
 	},
 	/* IR port */
 	[1] = {
 		.hwport	     = 1,
 		.flags	     = 0,
 		.uart_flags  = UPF_CONS_FLOW,
 		.ucon	     = 0x2c5,
 		.ulcon	     = 0x43,
 		.ufcon	     = 0x51,
 	},
 	/* On the N30 the bluetooth controller is connected here.
 	 * On the N35 and variants the GPS receiver is connected here. */
 	[2] = {
 		.hwport	     = 2,
 		.flags	     = 0,
 		.ucon	     = 0x2c5,
 		.ulcon	     = 0x03,
 		.ufcon	     = 0x51,
 	},
 };

 static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
 {
 	switch (cmd)
 	{
 		case S3C2410_UDC_P_ENABLE :
 			s3c2410_gpio_setpin(S3C2410_GPB3, 1);
 			break;
 		case S3C2410_UDC_P_DISABLE :
 			s3c2410_gpio_setpin(S3C2410_GPB3, 0);
 			break;
 		case S3C2410_UDC_P_RESET :
 			break;
 		default:
 			break;
 	}
 }

 static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = {
 	.udc_command		= n30_udc_pullup,
 	.vbus_pin		= S3C2410_GPG1,
 	.vbus_pin_inverted	= 0,
 };

 static struct gpio_keys_button n30_buttons[] = {
 	{
 		.gpio		= S3C2410_GPF0,
 		.code		= KEY_POWER,
 		.desc		= "Power",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG9,
 		.code		= KEY_UP,
 		.desc		= "Thumbwheel Up",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG8,
 		.code		= KEY_DOWN,
 		.desc		= "Thumbwheel Down",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG7,
 		.code		= KEY_ENTER,
 		.desc		= "Thumbwheel Press",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF7,
 		.code		= KEY_HOMEPAGE,
 		.desc		= "Home",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF6,
 		.code		= KEY_CALENDAR,
 		.desc		= "Calendar",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF5,
 		.code		= KEY_ADDRESSBOOK,
 		.desc		= "Contacts",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF4,
 		.code		= KEY_MAIL,
 		.desc		= "Mail",
 		.active_low	= 0,
 	},
 };

 static struct gpio_keys_platform_data n30_button_data = {
 	.buttons	= n30_buttons,
 	.nbuttons	= ARRAY_SIZE(n30_buttons),
 };

 static struct platform_device n30_button_device = {
 	.name		= "gpio-keys",
 	.id		= -1,
 	.dev		= {
 		.platform_data	= &n30_button_data,
 	}
 };

 static struct gpio_keys_button n35_buttons[] = {
 	{
 		.gpio		= S3C2410_GPF0,
 		.code		= KEY_POWER,
 		.desc		= "Power",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG9,
 		.code		= KEY_UP,
 		.desc		= "Joystick Up",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG8,
 		.code		= KEY_DOWN,
 		.desc		= "Joystick Down",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG6,
 		.code		= KEY_DOWN,
 		.desc		= "Joystick Left",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG5,
 		.code		= KEY_DOWN,
 		.desc		= "Joystick Right",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG7,
 		.code		= KEY_ENTER,
 		.desc		= "Joystick Press",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF7,
 		.code		= KEY_HOMEPAGE,
 		.desc		= "Home",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF6,
 		.code		= KEY_CALENDAR,
 		.desc		= "Calendar",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF5,
 		.code		= KEY_ADDRESSBOOK,
 		.desc		= "Contacts",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF4,
 		.code		= KEY_MAIL,
 		.desc		= "Mail",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPF3,
 		.code		= SW_RADIO,
 		.desc		= "GPS Antenna",
 		.active_low	= 0,
 	},
 	{
 		.gpio		= S3C2410_GPG2,
 		.code		= SW_HEADPHONE_INSERT,
 		.desc		= "Headphone",
 		.active_low	= 0,
 	},
 };

 static struct gpio_keys_platform_data n35_button_data = {
 	.buttons	= n35_buttons,
 	.nbuttons	= ARRAY_SIZE(n35_buttons),
 };

 static struct platform_device n35_button_device = {
 	.name		= "gpio-keys",
 	.id		= -1,
 	.num_resources	= 0,
 	.dev		= {
 		.platform_data	= &n35_button_data,
 	}
 };

 /* This is the bluetooth LED on the device. */
 static struct s3c24xx_led_platdata n30_blue_led_pdata = {
 	.name		= "blue_led",
 	.gpio		= S3C2410_GPG6,
 	.def_trigger	= "",
 };

 /* This LED is driven by the battery microcontroller, and is blinking
  * red, blinking green or solid green when the battery is low,
  * charging or full respectively.  By driving GPD9 low, it's possible
  * to force the LED to blink red, so call that warning LED.  */
 static struct s3c24xx_led_platdata n30_warning_led_pdata = {
 	.name		= "warning_led",
 	.flags          = S3C24XX_LEDF_ACTLOW,
 	.gpio		= S3C2410_GPD9,
 	.def_trigger	= "",
 };

 static struct platform_device n30_blue_led = {
 	.name		= "s3c24xx_led",
 	.id		= 1,
 	.dev		= {
 		.platform_data	= &n30_blue_led_pdata,
 	},
 };

 static struct platform_device n30_warning_led = {
 	.name		= "s3c24xx_led",
 	.id		= 2,
 	.dev		= {
 		.platform_data	= &n30_warning_led_pdata,
 	},
 };

 static struct platform_device *n30_devices[] __initdata = {
 	&s3c_device_lcd,
 	&s3c_device_wdt,
 	&s3c_device_i2c,
 	&s3c_device_iis,
 	&s3c_device_usb,
 	&s3c_device_usbgadget,
 	&n30_button_device,
 	&n30_blue_led,
 	&n30_warning_led,
 };

 static struct platform_device *n35_devices[] __initdata = {
 	&s3c_device_lcd,
 	&s3c_device_wdt,
 	&s3c_device_i2c,
 	&s3c_device_iis,
 	&s3c_device_usbgadget,
 	&n35_button_device,
 };

 static struct s3c2410_platform_i2c n30_i2ccfg = {
 	.flags		= 0,
 	.slave_addr	= 0x10,
 	.bus_freq	= 10*1000,
 	.max_freq	= 10*1000,
 };

 static void __init n30_map_io(void)
 {
 	s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc));
 	s3c24xx_init_clocks(0);
 	s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs));
 }

 static void __init n30_init_irq(void)
 {
 	s3c24xx_init_irq();
 }

 /* GPB3 is the line that controls the pull-up for the USB D+ line */

 static void __init n30_init(void)
 {
 	s3c_device_i2c.dev.platform_data = &n30_i2ccfg;
 	s3c24xx_udc_set_platdata(&n30_udc_cfg);

 	/* Turn off suspend on both USB ports, and switch the
 	 * selectable USB port to USB device mode. */

 	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
 			      S3C2410_MISCCR_USBSUSPND0 |
 			      S3C2410_MISCCR_USBSUSPND1, 0x0);

 	if (machine_is_n30()) {
 		/* Turn off suspend on both USB ports, and switch the
 		 * selectable USB port to USB device mode. */
 		s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
 				      S3C2410_MISCCR_USBSUSPND0 |
 				      S3C2410_MISCCR_USBSUSPND1, 0x0);

 		platform_add_devices(n30_devices, ARRAY_SIZE(n30_devices));
 	}

 	if (machine_is_n35()) {
 		/* Turn off suspend and switch the selectable USB port
 		 * to USB device mode.  Turn on suspend for the host
 		 * port since it is not connected on the N35.
 		 *
 		 * Actually, the host port is available at some pads
 		 * on the back of the device, so it would actually be
 		 * possible to add a USB device inside the N35 if you
 		 * are willing to do some hardware modifications. */
 		s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST |
 				      S3C2410_MISCCR_USBSUSPND0 |
 				      S3C2410_MISCCR_USBSUSPND1,
 				      S3C2410_MISCCR_USBSUSPND1);

 		platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices));
 	}
 }

 MACHINE_START(N30, "Acer-N30")
 	/* Maintainer: Christer Weinigel <christer@weinigel.se>,
 				Ben Dooks <ben-linux@fluff.org>
 	*/
 	.phys_io	= S3C2410_PA_UART,
 	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
 	.boot_params	= S3C2410_SDRAM_PA + 0x100,
 	.timer		= &s3c24xx_timer,
 	.init_machine	= n30_init,
 	.init_irq	= n30_init_irq,
 	.map_io		= n30_map_io,
 MACHINE_END

 MACHINE_START(N35, "Acer-N35")
 	/* Maintainer: Christer Weinigel <christer@weinigel.se>
 	*/
 	.phys_io	= S3C2410_PA_UART,
 	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
 	.boot_params	= S3C2410_SDRAM_PA + 0x100,
 	.timer		= &s3c24xx_timer,
 	.init_machine	= n30_init,
 	.init_irq	= n30_init_irq,
 	.map_io		= n30_map_io,
 MACHINE_END
	/* Machine specific code for the Acer n30, Acer N35, Navman PiN 570,
	* Yakumo AlphaX and Airis NC05 PDAs.
	*
	* Copyright (c) 2003-2005 Simtec Electronics
	* Ben Dooks <ben@simtec.co.uk>
	*
	* Copyright (c) 2005-2008 Christer Weinigel <christer@weinigel.se>
	*
	* There is a wiki with more information about the n30 port at
	* http://handhelds.org/moin/moin.cgi/AcerN30Documentation .
	*
	* This program is free software; you can redistribute it and/or modify
	* it under the terms of the GNU General Public License version 2 as
	* published by the Free Software Foundation.
	*/

	#include <linux/kernel.h>
	#include <linux/types.h>

	#include <linux/delay.h>
	#include <linux/gpio_keys.h>
	#include <linux/init.h>
	#include <linux/input.h>
	#include <linux/interrupt.h>
	#include <linux/platform_device.h>
	#include <linux/serial_core.h>
	#include <linux/timer.h>

	#include <asm/hardware.h>
	#include <asm/io.h>
	#include <asm/irq.h>
	#include <asm/mach-types.h>

	#include <asm/arch/leds-gpio.h>
	#include <asm/arch/regs-gpio.h>

	#include <asm/mach/arch.h>
	#include <asm/mach/irq.h>
	#include <asm/mach/map.h>

	#include <asm/plat-s3c/iic.h>
	#include <asm/plat-s3c/regs-serial.h>

	#include <asm/plat-s3c24xx/clock.h>
	#include <asm/plat-s3c24xx/cpu.h>
	#include <asm/plat-s3c24xx/devs.h>
	#include <asm/plat-s3c24xx/s3c2410.h>
	#include <asm/plat-s3c24xx/udc.h>

	static struct map_desc n30_iodesc[] __initdata = {
	/* nothing here yet */
	};

	static struct s3c2410_uartcfg n30_uartcfgs[] = {
	/* Normal serial port */
	[0] = {
	.hwport = 0,
	.flags = 0,
	.ucon = 0x2c5,
	.ulcon = 0x03,
	.ufcon = 0x51,
	},
	/* IR port */
	[1] = {
	.hwport = 1,
	.flags = 0,
	.uart_flags = UPF_CONS_FLOW,
	.ucon = 0x2c5,
	.ulcon = 0x43,
	.ufcon = 0x51,
	},
	/* On the N30 the bluetooth controller is connected here.
	* On the N35 and variants the GPS receiver is connected here. */
	[2] = {
	.hwport = 2,
	.flags = 0,
	.ucon = 0x2c5,
	.ulcon = 0x03,
	.ufcon = 0x51,
	},
	};

	static void n30_udc_pullup(enum s3c2410_udc_cmd_e cmd)
	{
	switch (cmd)
	{
	case S3C2410_UDC_P_ENABLE :
	s3c2410_gpio_setpin(S3C2410_GPB3, 1);
	break;
	case S3C2410_UDC_P_DISABLE :
	s3c2410_gpio_setpin(S3C2410_GPB3, 0);
	break;
	case S3C2410_UDC_P_RESET :
	break;
	default:
	break;
	}
	}

	static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = {
	.udc_command = n30_udc_pullup,
	.vbus_pin = S3C2410_GPG1,
	.vbus_pin_inverted = 0,
	};

	static struct gpio_keys_button n30_buttons[] = {
	{
	.gpio = S3C2410_GPF0,
	.code = KEY_POWER,
	.desc = "Power",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG9,
	.code = KEY_UP,
	.desc = "Thumbwheel Up",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG8,
	.code = KEY_DOWN,
	.desc = "Thumbwheel Down",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG7,
	.code = KEY_ENTER,
	.desc = "Thumbwheel Press",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF7,
	.code = KEY_HOMEPAGE,
	.desc = "Home",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF6,
	.code = KEY_CALENDAR,
	.desc = "Calendar",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF5,
	.code = KEY_ADDRESSBOOK,
	.desc = "Contacts",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF4,
	.code = KEY_MAIL,
	.desc = "Mail",
	.active_low = 0,
	},
	};

	static struct gpio_keys_platform_data n30_button_data = {
	.buttons = n30_buttons,
	.nbuttons = ARRAY_SIZE(n30_buttons),
	};

	static struct platform_device n30_button_device = {
	.name = "gpio-keys",
	.id = -1,
	.dev = {
	.platform_data = &n30_button_data,
	}
	};

	static struct gpio_keys_button n35_buttons[] = {
	{
	.gpio = S3C2410_GPF0,
	.code = KEY_POWER,
	.desc = "Power",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG9,
	.code = KEY_UP,
	.desc = "Joystick Up",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG8,
	.code = KEY_DOWN,
	.desc = "Joystick Down",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG6,
	.code = KEY_DOWN,
	.desc = "Joystick Left",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG5,
	.code = KEY_DOWN,
	.desc = "Joystick Right",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG7,
	.code = KEY_ENTER,
	.desc = "Joystick Press",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF7,
	.code = KEY_HOMEPAGE,
	.desc = "Home",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF6,
	.code = KEY_CALENDAR,
	.desc = "Calendar",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF5,
	.code = KEY_ADDRESSBOOK,
	.desc = "Contacts",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF4,
	.code = KEY_MAIL,
	.desc = "Mail",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPF3,
	.code = SW_RADIO,
	.desc = "GPS Antenna",
	.active_low = 0,
	},
	{
	.gpio = S3C2410_GPG2,
	.code = SW_HEADPHONE_INSERT,
	.desc = "Headphone",
	.active_low = 0,
	},
	};

	static struct gpio_keys_platform_data n35_button_data = {
	.buttons = n35_buttons,
	.nbuttons = ARRAY_SIZE(n35_buttons),
	};

	static struct platform_device n35_button_device = {
	.name = "gpio-keys",
	.id = -1,
	.num_resources = 0,
	.dev = {
	.platform_data = &n35_button_data,
	}
	};

	/* This is the bluetooth LED on the device. */
	static struct s3c24xx_led_platdata n30_blue_led_pdata = {
	.name = "blue_led",
	.gpio = S3C2410_GPG6,
	.def_trigger = "",
	};

	/* This LED is driven by the battery microcontroller, and is blinking
	* red, blinking green or solid green when the battery is low,
	* charging or full respectively. By driving GPD9 low, it's possible
	* to force the LED to blink red, so call that warning LED. */
	static struct s3c24xx_led_platdata n30_warning_led_pdata = {
	.name = "warning_led",
	.flags = S3C24XX_LEDF_ACTLOW,
	.gpio = S3C2410_GPD9,
	.def_trigger = "",
	};

	static struct platform_device n30_blue_led = {
	.name = "s3c24xx_led",
	.id = 1,
	.dev = {
	.platform_data = &n30_blue_led_pdata,
	},
	};

	static struct platform_device n30_warning_led = {
	.name = "s3c24xx_led",
	.id = 2,
	.dev = {
	.platform_data = &n30_warning_led_pdata,
	},
	};

	static struct platform_device *n30_devices[] __initdata = {
	&s3c_device_lcd,
	&s3c_device_wdt,
	&s3c_device_i2c,
	&s3c_device_iis,
	&s3c_device_usb,
	&s3c_device_usbgadget,
	&n30_button_device,
	&n30_blue_led,
	&n30_warning_led,
	};

	static struct platform_device *n35_devices[] __initdata = {
	&s3c_device_lcd,
	&s3c_device_wdt,
	&s3c_device_i2c,
	&s3c_device_iis,
	&s3c_device_usbgadget,
	&n35_button_device,
	};

	static struct s3c2410_platform_i2c n30_i2ccfg = {
	.flags = 0,
	.slave_addr = 0x10,
	.bus_freq = 10*1000,
	.max_freq = 10*1000,
	};

	static void __init n30_map_io(void)
	{
	s3c24xx_init_io(n30_iodesc, ARRAY_SIZE(n30_iodesc));
	s3c24xx_init_clocks(0);
	s3c24xx_init_uarts(n30_uartcfgs, ARRAY_SIZE(n30_uartcfgs));
	}

	static void __init n30_init_irq(void)
	{
	s3c24xx_init_irq();
	}

	/* GPB3 is the line that controls the pull-up for the USB D+ line */

	static void __init n30_init(void)
	{
	s3c_device_i2c.dev.platform_data = &n30_i2ccfg;
	s3c24xx_udc_set_platdata(&n30_udc_cfg);

	/* Turn off suspend on both USB ports, and switch the
	* selectable USB port to USB device mode. */

	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST \|
	S3C2410_MISCCR_USBSUSPND0 \|
	S3C2410_MISCCR_USBSUSPND1, 0x0);

	if (machine_is_n30()) {
	/* Turn off suspend on both USB ports, and switch the
	* selectable USB port to USB device mode. */
	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST \|
	S3C2410_MISCCR_USBSUSPND0 \|
	S3C2410_MISCCR_USBSUSPND1, 0x0);

	platform_add_devices(n30_devices, ARRAY_SIZE(n30_devices));
	}

	if (machine_is_n35()) {
	/* Turn off suspend and switch the selectable USB port
	* to USB device mode. Turn on suspend for the host
	* port since it is not connected on the N35.
	*
	* Actually, the host port is available at some pads
	* on the back of the device, so it would actually be
	* possible to add a USB device inside the N35 if you
	* are willing to do some hardware modifications. */
	s3c2410_modify_misccr(S3C2410_MISCCR_USBHOST \|
	S3C2410_MISCCR_USBSUSPND0 \|
	S3C2410_MISCCR_USBSUSPND1,
	S3C2410_MISCCR_USBSUSPND1);

	platform_add_devices(n35_devices, ARRAY_SIZE(n35_devices));
	}
	}

	MACHINE_START(N30, "Acer-N30")
	/* Maintainer: Christer Weinigel <christer@weinigel.se>,
	Ben Dooks <ben-linux@fluff.org>
	*/
	.phys_io = S3C2410_PA_UART,
	.io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
	.boot_params = S3C2410_SDRAM_PA + 0x100,
	.timer = &s3c24xx_timer,
	.init_machine = n30_init,
	.init_irq = n30_init_irq,
	.map_io = n30_map_io,
	MACHINE_END

	MACHINE_START(N35, "Acer-N35")
	/* Maintainer: Christer Weinigel <christer@weinigel.se>
	*/
	.phys_io = S3C2410_PA_UART,
	.io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
	.boot_params = S3C2410_SDRAM_PA + 0x100,
	.timer = &s3c24xx_timer,
	.init_machine = n30_init,
	.init_irq = n30_init_irq,
	.map_io = n30_map_io,
	MACHINE_END