| /* |
| * Copyright 2004-2009 Analog Devices Inc. |
| * 2005 National ICT Australia (NICTA) |
| * Aidan Williams <aidan@nicta.com.au> |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #include <linux/device.h> |
| #include <linux/etherdevice.h> |
| #include <linux/platform_device.h> |
| #include <linux/mtd/mtd.h> |
| #include <linux/mtd/partitions.h> |
| #include <linux/spi/spi.h> |
| #include <linux/spi/flash.h> |
| #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) |
| #include <linux/usb/isp1362.h> |
| #endif |
| #include <linux/irq.h> |
| #include <asm/dma.h> |
| #include <asm/bfin5xx_spi.h> |
| #include <asm/portmux.h> |
| #include <linux/usb/sl811.h> |
| |
| #include <linux/spi/ad7877.h> |
| |
| /* |
| * Name the Board for the /proc/cpuinfo |
| */ |
| const char bfin_board_name[] = "ADI PNAV-1.0"; |
| |
| /* |
| * Driver needs to know address, irq and flag pin. |
| */ |
| |
| #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) |
| static struct resource bfin_pcmcia_cf_resources[] = { |
| { |
| .start = 0x20310000, /* IO PORT */ |
| .end = 0x20312000, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = 0x20311000, /* Attribute Memory */ |
| .end = 0x20311FFF, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = IRQ_PF4, |
| .end = IRQ_PF4, |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, |
| }, { |
| .start = 6, /* Card Detect PF6 */ |
| .end = 6, |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| static struct platform_device bfin_pcmcia_cf_device = { |
| .name = "bfin_cf_pcmcia", |
| .id = -1, |
| .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources), |
| .resource = bfin_pcmcia_cf_resources, |
| }; |
| #endif |
| |
| #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) |
| static struct platform_device rtc_device = { |
| .name = "rtc-bfin", |
| .id = -1, |
| }; |
| #endif |
| |
| #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) |
| #include <linux/smc91x.h> |
| |
| static struct smc91x_platdata smc91x_info = { |
| .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT, |
| .leda = RPC_LED_100_10, |
| .ledb = RPC_LED_TX_RX, |
| }; |
| |
| static struct resource smc91x_resources[] = { |
| { |
| .name = "smc91x-regs", |
| .start = 0x20300300, |
| .end = 0x20300300 + 16, |
| .flags = IORESOURCE_MEM, |
| }, { |
| |
| .start = IRQ_PF7, |
| .end = IRQ_PF7, |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, |
| }, |
| }; |
| static struct platform_device smc91x_device = { |
| .name = "smc91x", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(smc91x_resources), |
| .resource = smc91x_resources, |
| .dev = { |
| .platform_data = &smc91x_info, |
| }, |
| }; |
| #endif |
| |
| #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE) |
| static struct resource sl811_hcd_resources[] = { |
| { |
| .start = 0x20340000, |
| .end = 0x20340000, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = 0x20340004, |
| .end = 0x20340004, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = CONFIG_USB_SL811_BFIN_IRQ, |
| .end = CONFIG_USB_SL811_BFIN_IRQ, |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, |
| }, |
| }; |
| |
| #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS) |
| void sl811_port_power(struct device *dev, int is_on) |
| { |
| gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS"); |
| gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on); |
| |
| } |
| #endif |
| |
| static struct sl811_platform_data sl811_priv = { |
| .potpg = 10, |
| .power = 250, /* == 500mA */ |
| #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS) |
| .port_power = &sl811_port_power, |
| #endif |
| }; |
| |
| static struct platform_device sl811_hcd_device = { |
| .name = "sl811-hcd", |
| .id = 0, |
| .dev = { |
| .platform_data = &sl811_priv, |
| }, |
| .num_resources = ARRAY_SIZE(sl811_hcd_resources), |
| .resource = sl811_hcd_resources, |
| }; |
| #endif |
| |
| #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) |
| static struct resource isp1362_hcd_resources[] = { |
| { |
| .start = 0x20360000, |
| .end = 0x20360000, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = 0x20360004, |
| .end = 0x20360004, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ, |
| .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ, |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, |
| }, |
| }; |
| |
| static struct isp1362_platform_data isp1362_priv = { |
| .sel15Kres = 1, |
| .clknotstop = 0, |
| .oc_enable = 0, |
| .int_act_high = 0, |
| .int_edge_triggered = 0, |
| .remote_wakeup_connected = 0, |
| .no_power_switching = 1, |
| .power_switching_mode = 0, |
| }; |
| |
| static struct platform_device isp1362_hcd_device = { |
| .name = "isp1362-hcd", |
| .id = 0, |
| .dev = { |
| .platform_data = &isp1362_priv, |
| }, |
| .num_resources = ARRAY_SIZE(isp1362_hcd_resources), |
| .resource = isp1362_hcd_resources, |
| }; |
| #endif |
| |
| #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) |
| static struct platform_device bfin_mii_bus = { |
| .name = "bfin_mii_bus", |
| }; |
| |
| static struct platform_device bfin_mac_device = { |
| .name = "bfin_mac", |
| .dev.platform_data = &bfin_mii_bus, |
| }; |
| #endif |
| |
| #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) |
| static struct resource net2272_bfin_resources[] = { |
| { |
| .start = 0x20300000, |
| .end = 0x20300000 + 0x100, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = IRQ_PF7, |
| .end = IRQ_PF7, |
| .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL, |
| }, |
| }; |
| |
| static struct platform_device net2272_bfin_device = { |
| .name = "net2272", |
| .id = -1, |
| .num_resources = ARRAY_SIZE(net2272_bfin_resources), |
| .resource = net2272_bfin_resources, |
| }; |
| #endif |
| |
| #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) |
| /* all SPI peripherals info goes here */ |
| |
| #if defined(CONFIG_MTD_M25P80) \ |
| || defined(CONFIG_MTD_M25P80_MODULE) |
| static struct mtd_partition bfin_spi_flash_partitions[] = { |
| { |
| .name = "bootloader(spi)", |
| .size = 0x00020000, |
| .offset = 0, |
| .mask_flags = MTD_CAP_ROM |
| }, { |
| .name = "linux kernel(spi)", |
| .size = 0xe0000, |
| .offset = 0x20000 |
| }, { |
| .name = "file system(spi)", |
| .size = 0x700000, |
| .offset = 0x00100000, |
| } |
| }; |
| |
| static struct flash_platform_data bfin_spi_flash_data = { |
| .name = "m25p80", |
| .parts = bfin_spi_flash_partitions, |
| .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions), |
| .type = "m25p64", |
| }; |
| |
| /* SPI flash chip (m25p64) */ |
| static struct bfin5xx_spi_chip spi_flash_chip_info = { |
| .enable_dma = 0, /* use dma transfer with this chip*/ |
| .bits_per_word = 8, |
| }; |
| #endif |
| |
| #if defined(CONFIG_BFIN_SPI_ADC) \ |
| || defined(CONFIG_BFIN_SPI_ADC_MODULE) |
| /* SPI ADC chip */ |
| static struct bfin5xx_spi_chip spi_adc_chip_info = { |
| .enable_dma = 1, /* use dma transfer with this chip*/ |
| .bits_per_word = 16, |
| }; |
| #endif |
| |
| #if defined(CONFIG_SND_BLACKFIN_AD1836) \ |
| || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) |
| static struct bfin5xx_spi_chip ad1836_spi_chip_info = { |
| .enable_dma = 0, |
| .bits_per_word = 16, |
| }; |
| #endif |
| |
| #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) |
| static struct bfin5xx_spi_chip mmc_spi_chip_info = { |
| .enable_dma = 0, |
| .bits_per_word = 8, |
| }; |
| #endif |
| |
| #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) |
| static struct bfin5xx_spi_chip spi_ad7877_chip_info = { |
| .cs_change_per_word = 0, |
| .enable_dma = 0, |
| .bits_per_word = 16, |
| }; |
| |
| static const struct ad7877_platform_data bfin_ad7877_ts_info = { |
| .model = 7877, |
| .vref_delay_usecs = 50, /* internal, no capacitor */ |
| .x_plate_ohms = 419, |
| .y_plate_ohms = 486, |
| .pressure_max = 1000, |
| .pressure_min = 0, |
| .stopacq_polarity = 1, |
| .first_conversion_delay = 3, |
| .acquisition_time = 1, |
| .averaging = 1, |
| .pen_down_acc_interval = 1, |
| }; |
| #endif |
| |
| static struct spi_board_info bfin_spi_board_info[] __initdata = { |
| #if defined(CONFIG_MTD_M25P80) \ |
| || defined(CONFIG_MTD_M25P80_MODULE) |
| { |
| /* the modalias must be the same as spi device driver name */ |
| .modalias = "m25p80", /* Name of spi_driver for this device */ |
| .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ |
| .bus_num = 0, /* Framework bus number */ |
| .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/ |
| .platform_data = &bfin_spi_flash_data, |
| .controller_data = &spi_flash_chip_info, |
| .mode = SPI_MODE_3, |
| }, |
| #endif |
| |
| #if defined(CONFIG_BFIN_SPI_ADC) \ |
| || defined(CONFIG_BFIN_SPI_ADC_MODULE) |
| { |
| .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */ |
| .max_speed_hz = 6250000, /* max spi clock (SCK) speed in HZ */ |
| .bus_num = 0, /* Framework bus number */ |
| .chip_select = 1, /* Framework chip select. */ |
| .platform_data = NULL, /* No spi_driver specific config */ |
| .controller_data = &spi_adc_chip_info, |
| }, |
| #endif |
| |
| #if defined(CONFIG_SND_BLACKFIN_AD1836) \ |
| || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE) |
| { |
| .modalias = "ad1836", |
| .max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */ |
| .bus_num = 0, |
| .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT, |
| .controller_data = &ad1836_spi_chip_info, |
| }, |
| #endif |
| #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE) |
| { |
| .modalias = "mmc_spi", |
| .max_speed_hz = 25000000, /* max spi clock (SCK) speed in HZ */ |
| .bus_num = 0, |
| .chip_select = 5, |
| .controller_data = &mmc_spi_chip_info, |
| .mode = SPI_MODE_3, |
| }, |
| #endif |
| #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE) |
| { |
| .modalias = "ad7877", |
| .platform_data = &bfin_ad7877_ts_info, |
| .irq = IRQ_PF2, |
| .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */ |
| .bus_num = 0, |
| .chip_select = 5, |
| .controller_data = &spi_ad7877_chip_info, |
| }, |
| #endif |
| |
| }; |
| |
| /* SPI (0) */ |
| static struct resource bfin_spi0_resource[] = { |
| [0] = { |
| .start = SPI0_REGBASE, |
| .end = SPI0_REGBASE + 0xFF, |
| .flags = IORESOURCE_MEM, |
| }, |
| [1] = { |
| .start = CH_SPI, |
| .end = CH_SPI, |
| .flags = IORESOURCE_DMA, |
| }, |
| [2] = { |
| .start = IRQ_SPI, |
| .end = IRQ_SPI, |
| .flags = IORESOURCE_IRQ, |
| }, |
| }; |
| |
| /* SPI controller data */ |
| static struct bfin5xx_spi_master bfin_spi0_info = { |
| .num_chipselect = 8, |
| .enable_dma = 1, /* master has the ability to do dma transfer */ |
| .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0}, |
| }; |
| |
| static struct platform_device bfin_spi0_device = { |
| .name = "bfin-spi", |
| .id = 0, /* Bus number */ |
| .num_resources = ARRAY_SIZE(bfin_spi0_resource), |
| .resource = bfin_spi0_resource, |
| .dev = { |
| .platform_data = &bfin_spi0_info, /* Passed to driver */ |
| }, |
| }; |
| #endif /* spi master and devices */ |
| |
| #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) |
| static struct platform_device bfin_fb_device = { |
| .name = "bf537-lq035", |
| }; |
| #endif |
| |
| #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) |
| static struct resource bfin_uart_resources[] = { |
| { |
| .start = 0xFFC00400, |
| .end = 0xFFC004FF, |
| .flags = IORESOURCE_MEM, |
| }, { |
| .start = 0xFFC02000, |
| .end = 0xFFC020FF, |
| .flags = IORESOURCE_MEM, |
| }, |
| }; |
| |
| static struct platform_device bfin_uart_device = { |
| .name = "bfin-uart", |
| .id = 1, |
| .num_resources = ARRAY_SIZE(bfin_uart_resources), |
| .resource = bfin_uart_resources, |
| }; |
| #endif |
| |
| #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) |
| #ifdef CONFIG_BFIN_SIR0 |
| static struct resource bfin_sir0_resources[] = { |
| { |
| .start = 0xFFC00400, |
| .end = 0xFFC004FF, |
| .flags = IORESOURCE_MEM, |
| }, |
| { |
| .start = IRQ_UART0_RX, |
| .end = IRQ_UART0_RX+1, |
| .flags = IORESOURCE_IRQ, |
| }, |
| { |
| .start = CH_UART0_RX, |
| .end = CH_UART0_RX+1, |
| .flags = IORESOURCE_DMA, |
| }, |
| }; |
| |
| static struct platform_device bfin_sir0_device = { |
| .name = "bfin_sir", |
| .id = 0, |
| .num_resources = ARRAY_SIZE(bfin_sir0_resources), |
| .resource = bfin_sir0_resources, |
| }; |
| #endif |
| #ifdef CONFIG_BFIN_SIR1 |
| static struct resource bfin_sir1_resources[] = { |
| { |
| .start = 0xFFC02000, |
| .end = 0xFFC020FF, |
| .flags = IORESOURCE_MEM, |
| }, |
| { |
| .start = IRQ_UART1_RX, |
| .end = IRQ_UART1_RX+1, |
| .flags = IORESOURCE_IRQ, |
| }, |
| { |
| .start = CH_UART1_RX, |
| .end = CH_UART1_RX+1, |
| .flags = IORESOURCE_DMA, |
| }, |
| }; |
| |
| static struct platform_device bfin_sir1_device = { |
| .name = "bfin_sir", |
| .id = 1, |
| .num_resources = ARRAY_SIZE(bfin_sir1_resources), |
| .resource = bfin_sir1_resources, |
| }; |
| #endif |
| #endif |
| |
| static struct platform_device *stamp_devices[] __initdata = { |
| #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE) |
| &bfin_pcmcia_cf_device, |
| #endif |
| |
| #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE) |
| &rtc_device, |
| #endif |
| |
| #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE) |
| &sl811_hcd_device, |
| #endif |
| |
| #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE) |
| &isp1362_hcd_device, |
| #endif |
| |
| #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) |
| &smc91x_device, |
| #endif |
| |
| #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE) |
| &bfin_mii_bus, |
| &bfin_mac_device, |
| #endif |
| |
| #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE) |
| &net2272_bfin_device, |
| #endif |
| |
| #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) |
| &bfin_spi0_device, |
| #endif |
| |
| #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE) |
| &bfin_fb_device, |
| #endif |
| |
| #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) |
| &bfin_uart_device, |
| #endif |
| |
| #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) |
| #ifdef CONFIG_BFIN_SIR0 |
| &bfin_sir0_device, |
| #endif |
| #ifdef CONFIG_BFIN_SIR1 |
| &bfin_sir1_device, |
| #endif |
| #endif |
| }; |
| |
| static int __init pnav_init(void) |
| { |
| printk(KERN_INFO "%s(): registering device resources\n", __func__); |
| platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices)); |
| #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE) |
| spi_register_board_info(bfin_spi_board_info, |
| ARRAY_SIZE(bfin_spi_board_info)); |
| #endif |
| return 0; |
| } |
| |
| arch_initcall(pnav_init); |
| |
| void bfin_get_ether_addr(char *addr) |
| { |
| random_ether_addr(addr); |
| printk(KERN_WARNING "%s:%s: Setting Ethernet MAC to a random one\n", __FILE__, __func__); |
| } |
| EXPORT_SYMBOL(bfin_get_ether_addr); |