| /* |
| * OMAP powerdomain control |
| * |
| * Copyright (C) 2007-2008 Texas Instruments, Inc. |
| * Copyright (C) 2007-2009 Nokia Corporation |
| * |
| * Written by Paul Walmsley |
| * Added OMAP4 specific support by Abhijit Pagare <abhijitpagare@ti.com> |
| * State counting code by Tero Kristo <tero.kristo@nokia.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| #undef DEBUG |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/types.h> |
| #include <linux/delay.h> |
| #include <linux/spinlock.h> |
| #include <linux/list.h> |
| #include <linux/errno.h> |
| #include <linux/err.h> |
| #include <linux/io.h> |
| |
| #include <asm/atomic.h> |
| |
| #include "cm.h" |
| #include "cm-regbits-34xx.h" |
| #include "cm-regbits-44xx.h" |
| #include "prm.h" |
| #include "prm-regbits-34xx.h" |
| #include "prm-regbits-44xx.h" |
| |
| #include <plat/cpu.h> |
| #include <plat/powerdomain.h> |
| #include <plat/clockdomain.h> |
| #include <plat/prcm.h> |
| |
| #include "pm.h" |
| |
| enum { |
| PWRDM_STATE_NOW = 0, |
| PWRDM_STATE_PREV, |
| }; |
| |
| /* Variable holding value of the CPU dependent PWRSTCTRL Register Offset */ |
| static u16 pwrstctrl_reg_offs; |
| |
| /* Variable holding value of the CPU dependent PWRSTST Register Offset */ |
| static u16 pwrstst_reg_offs; |
| |
| /* OMAP3 and OMAP4 specific register bit initialisations |
| * Notice that the names here are not according to each power |
| * domain but the bit mapping used applies to all of them |
| */ |
| |
| /* OMAP3 and OMAP4 Memory Onstate Masks (common across all power domains) */ |
| #define OMAP_MEM0_ONSTATE_MASK OMAP3430_SHAREDL1CACHEFLATONSTATE_MASK |
| #define OMAP_MEM1_ONSTATE_MASK OMAP3430_L1FLATMEMONSTATE_MASK |
| #define OMAP_MEM2_ONSTATE_MASK OMAP3430_SHAREDL2CACHEFLATONSTATE_MASK |
| #define OMAP_MEM3_ONSTATE_MASK OMAP3430_L2FLATMEMONSTATE_MASK |
| #define OMAP_MEM4_ONSTATE_MASK OMAP4430_OCP_NRET_BANK_ONSTATE_MASK |
| |
| /* OMAP3 and OMAP4 Memory Retstate Masks (common across all power domains) */ |
| #define OMAP_MEM0_RETSTATE_MASK OMAP3430_SHAREDL1CACHEFLATRETSTATE_MASK |
| #define OMAP_MEM1_RETSTATE_MASK OMAP3430_L1FLATMEMRETSTATE_MASK |
| #define OMAP_MEM2_RETSTATE_MASK OMAP3430_SHAREDL2CACHEFLATRETSTATE_MASK |
| #define OMAP_MEM3_RETSTATE_MASK OMAP3430_L2FLATMEMRETSTATE_MASK |
| #define OMAP_MEM4_RETSTATE_MASK OMAP4430_OCP_NRET_BANK_RETSTATE_MASK |
| |
| /* OMAP3 and OMAP4 Memory Status bits */ |
| #define OMAP_MEM0_STATEST_MASK OMAP3430_SHAREDL1CACHEFLATSTATEST_MASK |
| #define OMAP_MEM1_STATEST_MASK OMAP3430_L1FLATMEMSTATEST_MASK |
| #define OMAP_MEM2_STATEST_MASK OMAP3430_SHAREDL2CACHEFLATSTATEST_MASK |
| #define OMAP_MEM3_STATEST_MASK OMAP3430_L2FLATMEMSTATEST_MASK |
| #define OMAP_MEM4_STATEST_MASK OMAP4430_OCP_NRET_BANK_STATEST_MASK |
| |
| /* pwrdm_list contains all registered struct powerdomains */ |
| static LIST_HEAD(pwrdm_list); |
| |
| /* Private functions */ |
| |
| static struct powerdomain *_pwrdm_lookup(const char *name) |
| { |
| struct powerdomain *pwrdm, *temp_pwrdm; |
| |
| pwrdm = NULL; |
| |
| list_for_each_entry(temp_pwrdm, &pwrdm_list, node) { |
| if (!strcmp(name, temp_pwrdm->name)) { |
| pwrdm = temp_pwrdm; |
| break; |
| } |
| } |
| |
| return pwrdm; |
| } |
| |
| /** |
| * _pwrdm_register - register a powerdomain |
| * @pwrdm: struct powerdomain * to register |
| * |
| * Adds a powerdomain to the internal powerdomain list. Returns |
| * -EINVAL if given a null pointer, -EEXIST if a powerdomain is |
| * already registered by the provided name, or 0 upon success. |
| */ |
| static int _pwrdm_register(struct powerdomain *pwrdm) |
| { |
| int i; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (!omap_chip_is(pwrdm->omap_chip)) |
| return -EINVAL; |
| |
| if (_pwrdm_lookup(pwrdm->name)) |
| return -EEXIST; |
| |
| list_add(&pwrdm->node, &pwrdm_list); |
| |
| /* Initialize the powerdomain's state counter */ |
| for (i = 0; i < PWRDM_MAX_PWRSTS; i++) |
| pwrdm->state_counter[i] = 0; |
| |
| pwrdm->ret_logic_off_counter = 0; |
| for (i = 0; i < pwrdm->banks; i++) |
| pwrdm->ret_mem_off_counter[i] = 0; |
| |
| pwrdm_wait_transition(pwrdm); |
| pwrdm->state = pwrdm_read_pwrst(pwrdm); |
| pwrdm->state_counter[pwrdm->state] = 1; |
| |
| pr_debug("powerdomain: registered %s\n", pwrdm->name); |
| |
| return 0; |
| } |
| |
| static void _update_logic_membank_counters(struct powerdomain *pwrdm) |
| { |
| int i; |
| u8 prev_logic_pwrst, prev_mem_pwrst; |
| |
| prev_logic_pwrst = pwrdm_read_prev_logic_pwrst(pwrdm); |
| if ((pwrdm->pwrsts_logic_ret == PWRSTS_OFF_RET) && |
| (prev_logic_pwrst == PWRDM_POWER_OFF)) |
| pwrdm->ret_logic_off_counter++; |
| |
| for (i = 0; i < pwrdm->banks; i++) { |
| prev_mem_pwrst = pwrdm_read_prev_mem_pwrst(pwrdm, i); |
| |
| if ((pwrdm->pwrsts_mem_ret[i] == PWRSTS_OFF_RET) && |
| (prev_mem_pwrst == PWRDM_POWER_OFF)) |
| pwrdm->ret_mem_off_counter[i]++; |
| } |
| } |
| |
| static int _pwrdm_state_switch(struct powerdomain *pwrdm, int flag) |
| { |
| |
| int prev; |
| int state; |
| |
| if (pwrdm == NULL) |
| return -EINVAL; |
| |
| state = pwrdm_read_pwrst(pwrdm); |
| |
| switch (flag) { |
| case PWRDM_STATE_NOW: |
| prev = pwrdm->state; |
| break; |
| case PWRDM_STATE_PREV: |
| prev = pwrdm_read_prev_pwrst(pwrdm); |
| if (pwrdm->state != prev) |
| pwrdm->state_counter[prev]++; |
| if (prev == PWRDM_POWER_RET) |
| _update_logic_membank_counters(pwrdm); |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (state != prev) |
| pwrdm->state_counter[state]++; |
| |
| pm_dbg_update_time(pwrdm, prev); |
| |
| pwrdm->state = state; |
| |
| return 0; |
| } |
| |
| static int _pwrdm_pre_transition_cb(struct powerdomain *pwrdm, void *unused) |
| { |
| pwrdm_clear_all_prev_pwrst(pwrdm); |
| _pwrdm_state_switch(pwrdm, PWRDM_STATE_NOW); |
| return 0; |
| } |
| |
| static int _pwrdm_post_transition_cb(struct powerdomain *pwrdm, void *unused) |
| { |
| _pwrdm_state_switch(pwrdm, PWRDM_STATE_PREV); |
| return 0; |
| } |
| |
| /* Public functions */ |
| |
| /** |
| * pwrdm_init - set up the powerdomain layer |
| * @pwrdm_list: array of struct powerdomain pointers to register |
| * |
| * Loop through the array of powerdomains @pwrdm_list, registering all |
| * that are available on the current CPU. If pwrdm_list is supplied |
| * and not null, all of the referenced powerdomains will be |
| * registered. No return value. XXX pwrdm_list is not really a |
| * "list"; it is an array. Rename appropriately. |
| */ |
| void pwrdm_init(struct powerdomain **pwrdm_list) |
| { |
| struct powerdomain **p = NULL; |
| |
| if (cpu_is_omap24xx() || cpu_is_omap34xx()) { |
| pwrstctrl_reg_offs = OMAP2_PM_PWSTCTRL; |
| pwrstst_reg_offs = OMAP2_PM_PWSTST; |
| } else if (cpu_is_omap44xx()) { |
| pwrstctrl_reg_offs = OMAP4_PM_PWSTCTRL; |
| pwrstst_reg_offs = OMAP4_PM_PWSTST; |
| } else { |
| printk(KERN_ERR "Power Domain struct not supported for " \ |
| "this CPU\n"); |
| return; |
| } |
| |
| if (pwrdm_list) { |
| for (p = pwrdm_list; *p; p++) |
| _pwrdm_register(*p); |
| } |
| } |
| |
| /** |
| * pwrdm_lookup - look up a powerdomain by name, return a pointer |
| * @name: name of powerdomain |
| * |
| * Find a registered powerdomain by its name @name. Returns a pointer |
| * to the struct powerdomain if found, or NULL otherwise. |
| */ |
| struct powerdomain *pwrdm_lookup(const char *name) |
| { |
| struct powerdomain *pwrdm; |
| |
| if (!name) |
| return NULL; |
| |
| pwrdm = _pwrdm_lookup(name); |
| |
| return pwrdm; |
| } |
| |
| /** |
| * pwrdm_for_each - call function on each registered clockdomain |
| * @fn: callback function * |
| * |
| * Call the supplied function @fn for each registered powerdomain. |
| * The callback function @fn can return anything but 0 to bail out |
| * early from the iterator. Returns the last return value of the |
| * callback function, which should be 0 for success or anything else |
| * to indicate failure; or -EINVAL if the function pointer is null. |
| */ |
| int pwrdm_for_each(int (*fn)(struct powerdomain *pwrdm, void *user), |
| void *user) |
| { |
| struct powerdomain *temp_pwrdm; |
| int ret = 0; |
| |
| if (!fn) |
| return -EINVAL; |
| |
| list_for_each_entry(temp_pwrdm, &pwrdm_list, node) { |
| ret = (*fn)(temp_pwrdm, user); |
| if (ret) |
| break; |
| } |
| |
| return ret; |
| } |
| |
| /** |
| * pwrdm_add_clkdm - add a clockdomain to a powerdomain |
| * @pwrdm: struct powerdomain * to add the clockdomain to |
| * @clkdm: struct clockdomain * to associate with a powerdomain |
| * |
| * Associate the clockdomain @clkdm with a powerdomain @pwrdm. This |
| * enables the use of pwrdm_for_each_clkdm(). Returns -EINVAL if |
| * presented with invalid pointers; -ENOMEM if memory could not be allocated; |
| * or 0 upon success. |
| */ |
| int pwrdm_add_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm) |
| { |
| int i; |
| int ret = -EINVAL; |
| |
| if (!pwrdm || !clkdm) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: associating clockdomain %s with powerdomain " |
| "%s\n", clkdm->name, pwrdm->name); |
| |
| for (i = 0; i < PWRDM_MAX_CLKDMS; i++) { |
| if (!pwrdm->pwrdm_clkdms[i]) |
| break; |
| #ifdef DEBUG |
| if (pwrdm->pwrdm_clkdms[i] == clkdm) { |
| ret = -EINVAL; |
| goto pac_exit; |
| } |
| #endif |
| } |
| |
| if (i == PWRDM_MAX_CLKDMS) { |
| pr_debug("powerdomain: increase PWRDM_MAX_CLKDMS for " |
| "pwrdm %s clkdm %s\n", pwrdm->name, clkdm->name); |
| WARN_ON(1); |
| ret = -ENOMEM; |
| goto pac_exit; |
| } |
| |
| pwrdm->pwrdm_clkdms[i] = clkdm; |
| |
| ret = 0; |
| |
| pac_exit: |
| return ret; |
| } |
| |
| /** |
| * pwrdm_del_clkdm - remove a clockdomain from a powerdomain |
| * @pwrdm: struct powerdomain * to add the clockdomain to |
| * @clkdm: struct clockdomain * to associate with a powerdomain |
| * |
| * Dissociate the clockdomain @clkdm from the powerdomain |
| * @pwrdm. Returns -EINVAL if presented with invalid pointers; -ENOENT |
| * if @clkdm was not associated with the powerdomain, or 0 upon |
| * success. |
| */ |
| int pwrdm_del_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm) |
| { |
| int ret = -EINVAL; |
| int i; |
| |
| if (!pwrdm || !clkdm) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: dissociating clockdomain %s from powerdomain " |
| "%s\n", clkdm->name, pwrdm->name); |
| |
| for (i = 0; i < PWRDM_MAX_CLKDMS; i++) |
| if (pwrdm->pwrdm_clkdms[i] == clkdm) |
| break; |
| |
| if (i == PWRDM_MAX_CLKDMS) { |
| pr_debug("powerdomain: clkdm %s not associated with pwrdm " |
| "%s ?!\n", clkdm->name, pwrdm->name); |
| ret = -ENOENT; |
| goto pdc_exit; |
| } |
| |
| pwrdm->pwrdm_clkdms[i] = NULL; |
| |
| ret = 0; |
| |
| pdc_exit: |
| return ret; |
| } |
| |
| /** |
| * pwrdm_for_each_clkdm - call function on each clkdm in a pwrdm |
| * @pwrdm: struct powerdomain * to iterate over |
| * @fn: callback function * |
| * |
| * Call the supplied function @fn for each clockdomain in the powerdomain |
| * @pwrdm. The callback function can return anything but 0 to bail |
| * out early from the iterator. Returns -EINVAL if presented with |
| * invalid pointers; or passes along the last return value of the |
| * callback function, which should be 0 for success or anything else |
| * to indicate failure. |
| */ |
| int pwrdm_for_each_clkdm(struct powerdomain *pwrdm, |
| int (*fn)(struct powerdomain *pwrdm, |
| struct clockdomain *clkdm)) |
| { |
| int ret = 0; |
| int i; |
| |
| if (!fn) |
| return -EINVAL; |
| |
| for (i = 0; i < PWRDM_MAX_CLKDMS && !ret; i++) |
| ret = (*fn)(pwrdm, pwrdm->pwrdm_clkdms[i]); |
| |
| return ret; |
| } |
| |
| /** |
| * pwrdm_get_mem_bank_count - get number of memory banks in this powerdomain |
| * @pwrdm: struct powerdomain * |
| * |
| * Return the number of controllable memory banks in powerdomain @pwrdm, |
| * starting with 1. Returns -EINVAL if the powerdomain pointer is null. |
| */ |
| int pwrdm_get_mem_bank_count(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| return pwrdm->banks; |
| } |
| |
| /** |
| * pwrdm_set_next_pwrst - set next powerdomain power state |
| * @pwrdm: struct powerdomain * to set |
| * @pwrst: one of the PWRDM_POWER_* macros |
| * |
| * Set the powerdomain @pwrdm's next power state to @pwrst. The powerdomain |
| * may not enter this state immediately if the preconditions for this state |
| * have not been satisfied. Returns -EINVAL if the powerdomain pointer is |
| * null or if the power state is invalid for the powerdomin, or returns 0 |
| * upon success. |
| */ |
| int pwrdm_set_next_pwrst(struct powerdomain *pwrdm, u8 pwrst) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (!(pwrdm->pwrsts & (1 << pwrst))) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: setting next powerstate for %s to %0x\n", |
| pwrdm->name, pwrst); |
| |
| prm_rmw_mod_reg_bits(OMAP_POWERSTATE_MASK, |
| (pwrst << OMAP_POWERSTATE_SHIFT), |
| pwrdm->prcm_offs, pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_read_next_pwrst - get next powerdomain power state |
| * @pwrdm: struct powerdomain * to get power state |
| * |
| * Return the powerdomain @pwrdm's next power state. Returns -EINVAL |
| * if the powerdomain pointer is null or returns the next power state |
| * upon success. |
| */ |
| int pwrdm_read_next_pwrst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, |
| pwrstctrl_reg_offs, OMAP_POWERSTATE_MASK); |
| } |
| |
| /** |
| * pwrdm_read_pwrst - get current powerdomain power state |
| * @pwrdm: struct powerdomain * to get power state |
| * |
| * Return the powerdomain @pwrdm's current power state. Returns -EINVAL |
| * if the powerdomain pointer is null or returns the current power state |
| * upon success. |
| */ |
| int pwrdm_read_pwrst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, |
| pwrstst_reg_offs, OMAP_POWERSTATEST_MASK); |
| } |
| |
| /** |
| * pwrdm_read_prev_pwrst - get previous powerdomain power state |
| * @pwrdm: struct powerdomain * to get previous power state |
| * |
| * Return the powerdomain @pwrdm's previous power state. Returns -EINVAL |
| * if the powerdomain pointer is null or returns the previous power state |
| * upon success. |
| */ |
| int pwrdm_read_prev_pwrst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, OMAP3430_PM_PREPWSTST, |
| OMAP3430_LASTPOWERSTATEENTERED_MASK); |
| } |
| |
| /** |
| * pwrdm_set_logic_retst - set powerdomain logic power state upon retention |
| * @pwrdm: struct powerdomain * to set |
| * @pwrst: one of the PWRDM_POWER_* macros |
| * |
| * Set the next power state @pwrst that the logic portion of the |
| * powerdomain @pwrdm will enter when the powerdomain enters retention. |
| * This will be either RETENTION or OFF, if supported. Returns |
| * -EINVAL if the powerdomain pointer is null or the target power |
| * state is not not supported, or returns 0 upon success. |
| */ |
| int pwrdm_set_logic_retst(struct powerdomain *pwrdm, u8 pwrst) |
| { |
| u32 v; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (!(pwrdm->pwrsts_logic_ret & (1 << pwrst))) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: setting next logic powerstate for %s to %0x\n", |
| pwrdm->name, pwrst); |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| v = pwrst << __ffs(OMAP3430_LOGICL1CACHERETSTATE_MASK); |
| prm_rmw_mod_reg_bits(OMAP3430_LOGICL1CACHERETSTATE_MASK, v, |
| pwrdm->prcm_offs, pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_set_mem_onst - set memory power state while powerdomain ON |
| * @pwrdm: struct powerdomain * to set |
| * @bank: memory bank number to set (0-3) |
| * @pwrst: one of the PWRDM_POWER_* macros |
| * |
| * Set the next power state @pwrst that memory bank @bank of the |
| * powerdomain @pwrdm will enter when the powerdomain enters the ON |
| * state. @bank will be a number from 0 to 3, and represents different |
| * types of memory, depending on the powerdomain. Returns -EINVAL if |
| * the powerdomain pointer is null or the target power state is not |
| * not supported for this memory bank, -EEXIST if the target memory |
| * bank does not exist or is not controllable, or returns 0 upon |
| * success. |
| */ |
| int pwrdm_set_mem_onst(struct powerdomain *pwrdm, u8 bank, u8 pwrst) |
| { |
| u32 m; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (pwrdm->banks < (bank + 1)) |
| return -EEXIST; |
| |
| if (!(pwrdm->pwrsts_mem_on[bank] & (1 << pwrst))) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: setting next memory powerstate for domain %s " |
| "bank %0x while pwrdm-ON to %0x\n", pwrdm->name, bank, pwrst); |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| switch (bank) { |
| case 0: |
| m = OMAP_MEM0_ONSTATE_MASK; |
| break; |
| case 1: |
| m = OMAP_MEM1_ONSTATE_MASK; |
| break; |
| case 2: |
| m = OMAP_MEM2_ONSTATE_MASK; |
| break; |
| case 3: |
| m = OMAP_MEM3_ONSTATE_MASK; |
| break; |
| case 4: |
| m = OMAP_MEM4_ONSTATE_MASK; |
| break; |
| default: |
| WARN_ON(1); /* should never happen */ |
| return -EEXIST; |
| } |
| |
| prm_rmw_mod_reg_bits(m, (pwrst << __ffs(m)), |
| pwrdm->prcm_offs, pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_set_mem_retst - set memory power state while powerdomain in RET |
| * @pwrdm: struct powerdomain * to set |
| * @bank: memory bank number to set (0-3) |
| * @pwrst: one of the PWRDM_POWER_* macros |
| * |
| * Set the next power state @pwrst that memory bank @bank of the |
| * powerdomain @pwrdm will enter when the powerdomain enters the |
| * RETENTION state. Bank will be a number from 0 to 3, and represents |
| * different types of memory, depending on the powerdomain. @pwrst |
| * will be either RETENTION or OFF, if supported. Returns -EINVAL if |
| * the powerdomain pointer is null or the target power state is not |
| * not supported for this memory bank, -EEXIST if the target memory |
| * bank does not exist or is not controllable, or returns 0 upon |
| * success. |
| */ |
| int pwrdm_set_mem_retst(struct powerdomain *pwrdm, u8 bank, u8 pwrst) |
| { |
| u32 m; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (pwrdm->banks < (bank + 1)) |
| return -EEXIST; |
| |
| if (!(pwrdm->pwrsts_mem_ret[bank] & (1 << pwrst))) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: setting next memory powerstate for domain %s " |
| "bank %0x while pwrdm-RET to %0x\n", pwrdm->name, bank, pwrst); |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| switch (bank) { |
| case 0: |
| m = OMAP_MEM0_RETSTATE_MASK; |
| break; |
| case 1: |
| m = OMAP_MEM1_RETSTATE_MASK; |
| break; |
| case 2: |
| m = OMAP_MEM2_RETSTATE_MASK; |
| break; |
| case 3: |
| m = OMAP_MEM3_RETSTATE_MASK; |
| break; |
| case 4: |
| m = OMAP_MEM4_RETSTATE_MASK; |
| break; |
| default: |
| WARN_ON(1); /* should never happen */ |
| return -EEXIST; |
| } |
| |
| prm_rmw_mod_reg_bits(m, (pwrst << __ffs(m)), pwrdm->prcm_offs, |
| pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_read_logic_pwrst - get current powerdomain logic retention power state |
| * @pwrdm: struct powerdomain * to get current logic retention power state |
| * |
| * Return the power state that the logic portion of powerdomain @pwrdm |
| * will enter when the powerdomain enters retention. Returns -EINVAL |
| * if the powerdomain pointer is null or returns the logic retention |
| * power state upon success. |
| */ |
| int pwrdm_read_logic_pwrst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, pwrstst_reg_offs, |
| OMAP3430_LOGICSTATEST_MASK); |
| } |
| |
| /** |
| * pwrdm_read_prev_logic_pwrst - get previous powerdomain logic power state |
| * @pwrdm: struct powerdomain * to get previous logic power state |
| * |
| * Return the powerdomain @pwrdm's previous logic power state. Returns |
| * -EINVAL if the powerdomain pointer is null or returns the previous |
| * logic power state upon success. |
| */ |
| int pwrdm_read_prev_logic_pwrst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, OMAP3430_PM_PREPWSTST, |
| OMAP3430_LASTLOGICSTATEENTERED_MASK); |
| } |
| |
| /** |
| * pwrdm_read_logic_retst - get next powerdomain logic power state |
| * @pwrdm: struct powerdomain * to get next logic power state |
| * |
| * Return the powerdomain pwrdm's logic power state. Returns -EINVAL |
| * if the powerdomain pointer is null or returns the next logic |
| * power state upon success. |
| */ |
| int pwrdm_read_logic_retst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, pwrstctrl_reg_offs, |
| OMAP3430_LOGICSTATEST_MASK); |
| } |
| |
| /** |
| * pwrdm_read_mem_pwrst - get current memory bank power state |
| * @pwrdm: struct powerdomain * to get current memory bank power state |
| * @bank: memory bank number (0-3) |
| * |
| * Return the powerdomain @pwrdm's current memory power state for bank |
| * @bank. Returns -EINVAL if the powerdomain pointer is null, -EEXIST if |
| * the target memory bank does not exist or is not controllable, or |
| * returns the current memory power state upon success. |
| */ |
| int pwrdm_read_mem_pwrst(struct powerdomain *pwrdm, u8 bank) |
| { |
| u32 m; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (pwrdm->banks < (bank + 1)) |
| return -EEXIST; |
| |
| if (pwrdm->flags & PWRDM_HAS_MPU_QUIRK) |
| bank = 1; |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| switch (bank) { |
| case 0: |
| m = OMAP_MEM0_STATEST_MASK; |
| break; |
| case 1: |
| m = OMAP_MEM1_STATEST_MASK; |
| break; |
| case 2: |
| m = OMAP_MEM2_STATEST_MASK; |
| break; |
| case 3: |
| m = OMAP_MEM3_STATEST_MASK; |
| break; |
| case 4: |
| m = OMAP_MEM4_STATEST_MASK; |
| break; |
| default: |
| WARN_ON(1); /* should never happen */ |
| return -EEXIST; |
| } |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, |
| pwrstst_reg_offs, m); |
| } |
| |
| /** |
| * pwrdm_read_prev_mem_pwrst - get previous memory bank power state |
| * @pwrdm: struct powerdomain * to get previous memory bank power state |
| * @bank: memory bank number (0-3) |
| * |
| * Return the powerdomain @pwrdm's previous memory power state for |
| * bank @bank. Returns -EINVAL if the powerdomain pointer is null, |
| * -EEXIST if the target memory bank does not exist or is not |
| * controllable, or returns the previous memory power state upon |
| * success. |
| */ |
| int pwrdm_read_prev_mem_pwrst(struct powerdomain *pwrdm, u8 bank) |
| { |
| u32 m; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (pwrdm->banks < (bank + 1)) |
| return -EEXIST; |
| |
| if (pwrdm->flags & PWRDM_HAS_MPU_QUIRK) |
| bank = 1; |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| switch (bank) { |
| case 0: |
| m = OMAP3430_LASTMEM1STATEENTERED_MASK; |
| break; |
| case 1: |
| m = OMAP3430_LASTMEM2STATEENTERED_MASK; |
| break; |
| case 2: |
| m = OMAP3430_LASTSHAREDL2CACHEFLATSTATEENTERED_MASK; |
| break; |
| case 3: |
| m = OMAP3430_LASTL2FLATMEMSTATEENTERED_MASK; |
| break; |
| default: |
| WARN_ON(1); /* should never happen */ |
| return -EEXIST; |
| } |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, |
| OMAP3430_PM_PREPWSTST, m); |
| } |
| |
| /** |
| * pwrdm_read_mem_retst - get next memory bank power state |
| * @pwrdm: struct powerdomain * to get mext memory bank power state |
| * @bank: memory bank number (0-3) |
| * |
| * Return the powerdomain pwrdm's next memory power state for bank |
| * x. Returns -EINVAL if the powerdomain pointer is null, -EEXIST if |
| * the target memory bank does not exist or is not controllable, or |
| * returns the next memory power state upon success. |
| */ |
| int pwrdm_read_mem_retst(struct powerdomain *pwrdm, u8 bank) |
| { |
| u32 m; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (pwrdm->banks < (bank + 1)) |
| return -EEXIST; |
| |
| /* |
| * The register bit names below may not correspond to the |
| * actual names of the bits in each powerdomain's register, |
| * but the type of value returned is the same for each |
| * powerdomain. |
| */ |
| switch (bank) { |
| case 0: |
| m = OMAP_MEM0_RETSTATE_MASK; |
| break; |
| case 1: |
| m = OMAP_MEM1_RETSTATE_MASK; |
| break; |
| case 2: |
| m = OMAP_MEM2_RETSTATE_MASK; |
| break; |
| case 3: |
| m = OMAP_MEM3_RETSTATE_MASK; |
| break; |
| case 4: |
| m = OMAP_MEM4_RETSTATE_MASK; |
| default: |
| WARN_ON(1); /* should never happen */ |
| return -EEXIST; |
| } |
| |
| return prm_read_mod_bits_shift(pwrdm->prcm_offs, |
| pwrstctrl_reg_offs, m); |
| } |
| |
| /** |
| * pwrdm_clear_all_prev_pwrst - clear previous powerstate register for a pwrdm |
| * @pwrdm: struct powerdomain * to clear |
| * |
| * Clear the powerdomain's previous power state register @pwrdm. |
| * Clears the entire register, including logic and memory bank |
| * previous power states. Returns -EINVAL if the powerdomain pointer |
| * is null, or returns 0 upon success. |
| */ |
| int pwrdm_clear_all_prev_pwrst(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| /* |
| * XXX should get the powerdomain's current state here; |
| * warn & fail if it is not ON. |
| */ |
| |
| pr_debug("powerdomain: clearing previous power state reg for %s\n", |
| pwrdm->name); |
| |
| prm_write_mod_reg(0, pwrdm->prcm_offs, OMAP3430_PM_PREPWSTST); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_enable_hdwr_sar - enable automatic hardware SAR for a pwrdm |
| * @pwrdm: struct powerdomain * |
| * |
| * Enable automatic context save-and-restore upon power state change |
| * for some devices in the powerdomain @pwrdm. Warning: this only |
| * affects a subset of devices in a powerdomain; check the TRM |
| * closely. Returns -EINVAL if the powerdomain pointer is null or if |
| * the powerdomain does not support automatic save-and-restore, or |
| * returns 0 upon success. |
| */ |
| int pwrdm_enable_hdwr_sar(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (!(pwrdm->flags & PWRDM_HAS_HDWR_SAR)) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: %s: setting SAVEANDRESTORE bit\n", |
| pwrdm->name); |
| |
| prm_rmw_mod_reg_bits(0, 1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT, |
| pwrdm->prcm_offs, pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_disable_hdwr_sar - disable automatic hardware SAR for a pwrdm |
| * @pwrdm: struct powerdomain * |
| * |
| * Disable automatic context save-and-restore upon power state change |
| * for some devices in the powerdomain @pwrdm. Warning: this only |
| * affects a subset of devices in a powerdomain; check the TRM |
| * closely. Returns -EINVAL if the powerdomain pointer is null or if |
| * the powerdomain does not support automatic save-and-restore, or |
| * returns 0 upon success. |
| */ |
| int pwrdm_disable_hdwr_sar(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (!(pwrdm->flags & PWRDM_HAS_HDWR_SAR)) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: %s: clearing SAVEANDRESTORE bit\n", |
| pwrdm->name); |
| |
| prm_rmw_mod_reg_bits(1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT, 0, |
| pwrdm->prcm_offs, pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_has_hdwr_sar - test whether powerdomain supports hardware SAR |
| * @pwrdm: struct powerdomain * |
| * |
| * Returns 1 if powerdomain @pwrdm supports hardware save-and-restore |
| * for some devices, or 0 if it does not. |
| */ |
| bool pwrdm_has_hdwr_sar(struct powerdomain *pwrdm) |
| { |
| return (pwrdm && pwrdm->flags & PWRDM_HAS_HDWR_SAR) ? 1 : 0; |
| } |
| |
| /** |
| * pwrdm_set_lowpwrstchange - Request a low power state change |
| * @pwrdm: struct powerdomain * |
| * |
| * Allows a powerdomain to transtion to a lower power sleep state |
| * from an existing sleep state without waking up the powerdomain. |
| * Returns -EINVAL if the powerdomain pointer is null or if the |
| * powerdomain does not support LOWPOWERSTATECHANGE, or returns 0 |
| * upon success. |
| */ |
| int pwrdm_set_lowpwrstchange(struct powerdomain *pwrdm) |
| { |
| if (!pwrdm) |
| return -EINVAL; |
| |
| if (!(pwrdm->flags & PWRDM_HAS_LOWPOWERSTATECHANGE)) |
| return -EINVAL; |
| |
| pr_debug("powerdomain: %s: setting LOWPOWERSTATECHANGE bit\n", |
| pwrdm->name); |
| |
| prm_rmw_mod_reg_bits(OMAP4430_LOWPOWERSTATECHANGE_MASK, |
| (1 << OMAP4430_LOWPOWERSTATECHANGE_SHIFT), |
| pwrdm->prcm_offs, pwrstctrl_reg_offs); |
| |
| return 0; |
| } |
| |
| /** |
| * pwrdm_wait_transition - wait for powerdomain power transition to finish |
| * @pwrdm: struct powerdomain * to wait for |
| * |
| * If the powerdomain @pwrdm is in the process of a state transition, |
| * spin until it completes the power transition, or until an iteration |
| * bailout value is reached. Returns -EINVAL if the powerdomain |
| * pointer is null, -EAGAIN if the bailout value was reached, or |
| * returns 0 upon success. |
| */ |
| int pwrdm_wait_transition(struct powerdomain *pwrdm) |
| { |
| u32 c = 0; |
| |
| if (!pwrdm) |
| return -EINVAL; |
| |
| /* |
| * REVISIT: pwrdm_wait_transition() may be better implemented |
| * via a callback and a periodic timer check -- how long do we expect |
| * powerdomain transitions to take? |
| */ |
| |
| /* XXX Is this udelay() value meaningful? */ |
| while ((prm_read_mod_reg(pwrdm->prcm_offs, pwrstst_reg_offs) & |
| OMAP_INTRANSITION_MASK) && |
| (c++ < PWRDM_TRANSITION_BAILOUT)) |
| udelay(1); |
| |
| if (c > PWRDM_TRANSITION_BAILOUT) { |
| printk(KERN_ERR "powerdomain: waited too long for " |
| "powerdomain %s to complete transition\n", pwrdm->name); |
| return -EAGAIN; |
| } |
| |
| pr_debug("powerdomain: completed transition in %d loops\n", c); |
| |
| return 0; |
| } |
| |
| int pwrdm_state_switch(struct powerdomain *pwrdm) |
| { |
| return _pwrdm_state_switch(pwrdm, PWRDM_STATE_NOW); |
| } |
| |
| int pwrdm_clkdm_state_switch(struct clockdomain *clkdm) |
| { |
| if (clkdm != NULL && clkdm->pwrdm.ptr != NULL) { |
| pwrdm_wait_transition(clkdm->pwrdm.ptr); |
| return pwrdm_state_switch(clkdm->pwrdm.ptr); |
| } |
| |
| return -EINVAL; |
| } |
| |
| int pwrdm_pre_transition(void) |
| { |
| pwrdm_for_each(_pwrdm_pre_transition_cb, NULL); |
| return 0; |
| } |
| |
| int pwrdm_post_transition(void) |
| { |
| pwrdm_for_each(_pwrdm_post_transition_cb, NULL); |
| return 0; |
| } |
| |