[SCSI] isci: Fix task management for SMP, SATA and on dev remove.
libsas uses the LLDD abort task interface to handle I/O timeouts
in the SATA/STP and SMP discovery paths, so this change will terminate
STP/SMP requests. Also, if the device is gone, the lldd will prevent
libsas from further escalations in the error handler.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
diff --git a/drivers/scsi/isci/task.c b/drivers/scsi/isci/task.c
index c1f439b..ec85beb 100644
--- a/drivers/scsi/isci/task.c
+++ b/drivers/scsi/isci/task.c
@@ -920,22 +920,14 @@
"%s: domain_device=%p, isci_host=%p; isci_device=%p\n",
__func__, domain_device, isci_host, isci_device);
- if (isci_device)
- set_bit(IDEV_EH, &isci_device->flags);
+ if (!isci_device) {
+ /* If the device is gone, stop the escalations. */
+ dev_dbg(&isci_host->pdev->dev, "%s: No dev\n", __func__);
- /* If there is a device reset pending on any request in the
- * device's list, fail this LUN reset request in order to
- * escalate to the device reset.
- */
- if (!isci_device ||
- isci_device_is_reset_pending(isci_host, isci_device)) {
- dev_dbg(&isci_host->pdev->dev,
- "%s: No dev (%p), or "
- "RESET PENDING: domain_device=%p\n",
- __func__, isci_device, domain_device);
- ret = TMF_RESP_FUNC_FAILED;
+ ret = TMF_RESP_FUNC_COMPLETE;
goto out;
}
+ set_bit(IDEV_EH, &isci_device->flags);
/* Send the task management part of the reset. */
if (sas_protocol_ata(domain_device->tproto)) {
@@ -1044,7 +1036,7 @@
struct isci_tmf tmf;
int ret = TMF_RESP_FUNC_FAILED;
unsigned long flags;
- bool any_dev_reset = false;
+ int perform_termination = 0;
/* Get the isci_request reference from the task. Note that
* this check does not depend on the pending request list
@@ -1066,89 +1058,34 @@
spin_unlock_irqrestore(&isci_host->scic_lock, flags);
dev_dbg(&isci_host->pdev->dev,
- "%s: task = %p\n", __func__, task);
+ "%s: dev = %p, task = %p, old_request == %p\n",
+ __func__, isci_device, task, old_request);
- if (!isci_device || !old_request)
- goto out;
+ if (isci_device)
+ set_bit(IDEV_EH, &isci_device->flags);
- set_bit(IDEV_EH, &isci_device->flags);
-
- /* This version of the driver will fail abort requests for
- * SATA/STP. Failing the abort request this way will cause the
- * SCSI error handler thread to escalate to LUN reset
+ /* Device reset conditions signalled in task_state_flags are the
+ * responsbility of libsas to observe at the start of the error
+ * handler thread.
*/
- if (sas_protocol_ata(task->task_proto)) {
- dev_dbg(&isci_host->pdev->dev,
- " task %p is for a STP/SATA device;"
- " returning TMF_RESP_FUNC_FAILED\n"
- " to cause a LUN reset...\n", task);
- goto out;
- }
-
- dev_dbg(&isci_host->pdev->dev,
- "%s: old_request == %p\n", __func__, old_request);
-
- any_dev_reset = isci_device_is_reset_pending(isci_host, isci_device);
-
- spin_lock_irqsave(&task->task_state_lock, flags);
-
- any_dev_reset = any_dev_reset || (task->task_state_flags & SAS_TASK_NEED_DEV_RESET);
-
- /* If the extraction of the request reference from the task
- * failed, then the request has been completed (or if there is a
- * pending reset then this abort request function must be failed
- * in order to escalate to the target reset).
- */
- if ((old_request == NULL) || any_dev_reset) {
-
- /* If the device reset task flag is set, fail the task
- * management request. Otherwise, the original request
- * has completed.
- */
- if (any_dev_reset) {
-
- /* Turn off the task's DONE to make sure this
- * task is escalated to a target reset.
- */
- task->task_state_flags &= ~SAS_TASK_STATE_DONE;
-
- /* Make the reset happen as soon as possible. */
- task->task_state_flags |= SAS_TASK_NEED_DEV_RESET;
-
- spin_unlock_irqrestore(&task->task_state_lock, flags);
-
- /* Fail the task management request in order to
- * escalate to the target reset.
- */
- ret = TMF_RESP_FUNC_FAILED;
-
- dev_dbg(&isci_host->pdev->dev,
- "%s: Failing task abort in order to "
- "escalate to target reset because\n"
- "SAS_TASK_NEED_DEV_RESET is set for "
- "task %p on dev %p\n",
- __func__, task, isci_device);
-
-
- } else {
- /* The request has already completed and there
- * is nothing to do here other than to set the task
- * done bit, and indicate that the task abort function
- * was sucessful.
- */
- isci_set_task_doneflags(task);
-
- spin_unlock_irqrestore(&task->task_state_lock, flags);
-
- ret = TMF_RESP_FUNC_COMPLETE;
-
- dev_dbg(&isci_host->pdev->dev,
- "%s: abort task not needed for %p\n",
- __func__, task);
- }
- goto out;
- } else {
+ if (!isci_device || !old_request) {
+ /* The request has already completed and there
+ * is nothing to do here other than to set the task
+ * done bit, and indicate that the task abort function
+ * was sucessful.
+ */
+ spin_lock_irqsave(&task->task_state_lock, flags);
+ task->task_state_flags |= SAS_TASK_STATE_DONE;
+ task->task_state_flags &= ~(SAS_TASK_AT_INITIATOR |
+ SAS_TASK_STATE_PENDING);
spin_unlock_irqrestore(&task->task_state_lock, flags);
+
+ ret = TMF_RESP_FUNC_COMPLETE;
+
+ dev_dbg(&isci_host->pdev->dev,
+ "%s: abort task not needed for %p\n",
+ __func__, task);
+ goto out;
}
spin_lock_irqsave(&isci_host->scic_lock, flags);
@@ -1177,24 +1114,44 @@
goto out;
}
if (task->task_proto == SAS_PROTOCOL_SMP ||
+ sas_protocol_ata(task->task_proto) ||
test_bit(IREQ_COMPLETE_IN_TARGET, &old_request->flags)) {
spin_unlock_irqrestore(&isci_host->scic_lock, flags);
dev_dbg(&isci_host->pdev->dev,
- "%s: SMP request (%d)"
+ "%s: %s request"
" or complete_in_target (%d), thus no TMF\n",
- __func__, (task->task_proto == SAS_PROTOCOL_SMP),
+ __func__,
+ ((task->task_proto == SAS_PROTOCOL_SMP)
+ ? "SMP"
+ : (sas_protocol_ata(task->task_proto)
+ ? "SATA/STP"
+ : "<other>")
+ ),
test_bit(IREQ_COMPLETE_IN_TARGET, &old_request->flags));
- /* Set the state on the task. */
- isci_task_all_done(task);
+ if (test_bit(IREQ_COMPLETE_IN_TARGET, &old_request->flags)) {
+ spin_lock_irqsave(&task->task_state_lock, flags);
+ task->task_state_flags |= SAS_TASK_STATE_DONE;
+ task->task_state_flags &= ~(SAS_TASK_AT_INITIATOR |
+ SAS_TASK_STATE_PENDING);
+ spin_unlock_irqrestore(&task->task_state_lock, flags);
+ ret = TMF_RESP_FUNC_COMPLETE;
+ } else {
+ spin_lock_irqsave(&task->task_state_lock, flags);
+ task->task_state_flags &= ~(SAS_TASK_AT_INITIATOR |
+ SAS_TASK_STATE_PENDING);
+ spin_unlock_irqrestore(&task->task_state_lock, flags);
+ }
- ret = TMF_RESP_FUNC_COMPLETE;
-
- /* Stopping and SMP devices are not sent a TMF, and are not
- * reset, but the outstanding I/O request is terminated below.
+ /* STP and SMP devices are not sent a TMF, but the
+ * outstanding I/O request is terminated below. This is
+ * because SATA/STP and SMP discovery path timeouts directly
+ * call the abort task interface for cleanup.
*/
+ perform_termination = 1;
+
} else {
/* Fill in the tmf stucture */
isci_task_build_abort_task_tmf(&tmf, isci_tmf_ssp_task_abort,
@@ -1203,22 +1160,24 @@
spin_unlock_irqrestore(&isci_host->scic_lock, flags);
- #define ISCI_ABORT_TASK_TIMEOUT_MS 500 /* half second timeout. */
+ #define ISCI_ABORT_TASK_TIMEOUT_MS 500 /* 1/2 second timeout */
ret = isci_task_execute_tmf(isci_host, isci_device, &tmf,
ISCI_ABORT_TASK_TIMEOUT_MS);
- if (ret != TMF_RESP_FUNC_COMPLETE)
+ if (ret == TMF_RESP_FUNC_COMPLETE)
+ perform_termination = 1;
+ else
dev_dbg(&isci_host->pdev->dev,
- "%s: isci_task_send_tmf failed\n",
- __func__);
+ "%s: isci_task_send_tmf failed\n", __func__);
}
- if (ret == TMF_RESP_FUNC_COMPLETE) {
+ if (perform_termination) {
set_bit(IREQ_COMPLETE_IN_TARGET, &old_request->flags);
/* Clean up the request on our side, and wait for the aborted
* I/O to complete.
*/
- isci_terminate_request_core(isci_host, isci_device, old_request);
+ isci_terminate_request_core(isci_host, isci_device,
+ old_request);
}
/* Make sure we do not leave a reference to aborted_io_completion */