[ARM] 2888/1: OMAP 3/4: Update omap include files, take 2
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Start adding 24xx support by Paul Mundt
- Clean-up of cpu detection by Dirk Behme and Tony Lindgren
- Add DSP header by Toshihiro Kobayashi
- Add support for mtd-xip by Vladimir Barinov
- Add various new mux registers
- Move OMAP specific serial defines back to serial.h
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/include/asm-arm/arch-omap/board-h4.h b/include/asm-arm/arch-omap/board-h4.h
index 79138dcf..d64ee92 100644
--- a/include/asm-arm/arch-omap/board-h4.h
+++ b/include/asm-arm/arch-omap/board-h4.h
@@ -30,6 +30,9 @@
#define __ASM_ARCH_OMAP_H4_H
/* Placeholder for H4 specific defines */
+/* GPMC CS1 */
+#define OMAP24XX_ETHR_START 0x08000300
+#define OMAP24XX_ETHR_GPIO_IRQ 92
#endif /* __ASM_ARCH_OMAP_H4_H */
diff --git a/include/asm-arm/arch-omap/board-innovator.h b/include/asm-arm/arch-omap/board-innovator.h
index 0f1abae..79574e0 100644
--- a/include/asm-arm/arch-omap/board-innovator.h
+++ b/include/asm-arm/arch-omap/board-innovator.h
@@ -36,31 +36,6 @@
#define OMAP1510P1_EMIFS_PRI_VALUE 0x00
#define OMAP1510P1_EMIFF_PRI_VALUE 0x00
-/*
- * These definitions define an area of FLASH set aside
- * for the use of MTD/JFFS2. This is the area of flash
- * that a JFFS2 filesystem will reside which is mounted
- * at boot with the "root=/dev/mtdblock/0 rw"
- * command line option. The flash address used here must
- * fall within the legal range defined by rrload for storing
- * the filesystem component. This address will be sufficiently
- * deep into the overall flash range to avoid the other
- * components also stored in flash such as the bootloader,
- * the bootloader params, and the kernel.
- * The SW2 settings for the map below are:
- * 1 off, 2 off, 3 on, 4 off.
- */
-
-/* Intel flash_0, partitioned as expected by rrload */
-#define OMAP_FLASH_0_BASE 0xD8000000
-#define OMAP_FLASH_0_START 0x00000000
-#define OMAP_FLASH_0_SIZE SZ_16M
-
-/* Intel flash_1, used for cramfs or other flash file systems */
-#define OMAP_FLASH_1_BASE 0xD9000000
-#define OMAP_FLASH_1_START 0x01000000
-#define OMAP_FLASH_1_SIZE SZ_16M
-
#define NR_FPGA_IRQS 24
#define NR_IRQS IH_BOARD_BASE + NR_FPGA_IRQS
diff --git a/include/asm-arm/arch-omap/board-perseus2.h b/include/asm-arm/arch-omap/board-perseus2.h
index 0c224cc..691e52a 100644
--- a/include/asm-arm/arch-omap/board-perseus2.h
+++ b/include/asm-arm/arch-omap/board-perseus2.h
@@ -36,23 +36,14 @@
#define OMAP_SDRAM_DEVICE D256M_1X16_4B
#endif
-/*
- * These definitions define an area of FLASH set aside
- * for the use of MTD/JFFS2. This is the area of flash
- * that a JFFS2 filesystem will reside which is mounted
- * at boot with the "root=/dev/mtdblock/0 rw"
- * command line option.
- */
-
-/* Intel flash_0, partitioned as expected by rrload */
-#define OMAP_FLASH_0_BASE 0xD8000000 /* VA */
-#define OMAP_FLASH_0_START 0x00000000 /* PA */
-#define OMAP_FLASH_0_SIZE SZ_32M
-
#define MAXIRQNUM IH_BOARD_BASE
#define MAXFIQNUM MAXIRQNUM
#define MAXSWINUM MAXIRQNUM
#define NR_IRQS (MAXIRQNUM + 1)
+/* Samsung NAND flash at CS2B or CS3(NAND Boot) */
+#define OMAP_NAND_FLASH_START1 0x0A000000 /* CS2B */
+#define OMAP_NAND_FLASH_START2 0x0C000000 /* CS3 */
+
#endif
diff --git a/include/asm-arm/arch-omap/board-voiceblue.h b/include/asm-arm/arch-omap/board-voiceblue.h
index 33977b8..ed6d346 100644
--- a/include/asm-arm/arch-omap/board-voiceblue.h
+++ b/include/asm-arm/arch-omap/board-voiceblue.h
@@ -11,11 +11,6 @@
#ifndef __ASM_ARCH_VOICEBLUE_H
#define __ASM_ARCH_VOICEBLUE_H
-#if (EXTERNAL_MAX_NR_PORTS < 4)
-#undef EXTERNAL_MAX_NR_PORTS
-#define EXTERNAL_MAX_NR_PORTS 4
-#endif
-
extern void voiceblue_wdt_enable(void);
extern void voiceblue_wdt_disable(void);
extern void voiceblue_wdt_ping(void);
diff --git a/include/asm-arm/arch-omap/board.h b/include/asm-arm/arch-omap/board.h
index 95bd625..a0040cd 100644
--- a/include/asm-arm/arch-omap/board.h
+++ b/include/asm-arm/arch-omap/board.h
@@ -30,10 +30,23 @@
u8 system_clock_type;
};
+struct omap_mmc_conf {
+ unsigned enabled:1;
+ /* nomux means "standard" muxing is wrong on this board, and that
+ * board-specific code handled it before common init logic.
+ */
+ unsigned nomux:1;
+ /* switch pin can be for card detect (default) or card cover */
+ unsigned cover:1;
+ /* 4 wire signaling is optional, and is only used for SD/SDIO */
+ unsigned wire4:1;
+ s16 power_pin;
+ s16 switch_pin;
+ s16 wp_pin;
+};
+
struct omap_mmc_config {
- u8 mmc_blocks;
- s16 mmc1_power_pin, mmc2_power_pin;
- s16 mmc1_switch_pin, mmc2_switch_pin;
+ struct omap_mmc_conf mmc[2];
};
struct omap_serial_console_config {
diff --git a/include/asm-arm/arch-omap/cpu.h b/include/asm-arm/arch-omap/cpu.h
index e878671..1119e2b 100644
--- a/include/asm-arm/arch-omap/cpu.h
+++ b/include/asm-arm/arch-omap/cpu.h
@@ -38,146 +38,179 @@
/*
* Test if multicore OMAP support is needed
*/
-#undef MULTI_OMAP
+#undef MULTI_OMAP1
+#undef MULTI_OMAP2
#undef OMAP_NAME
#ifdef CONFIG_ARCH_OMAP730
# ifdef OMAP_NAME
-# undef MULTI_OMAP
-# define MULTI_OMAP
+# undef MULTI_OMAP1
+# define MULTI_OMAP1
# else
# define OMAP_NAME omap730
# endif
#endif
#ifdef CONFIG_ARCH_OMAP1510
# ifdef OMAP_NAME
-# undef MULTI_OMAP
-# define MULTI_OMAP
+# undef MULTI_OMAP1
+# define MULTI_OMAP1
# else
# define OMAP_NAME omap1510
# endif
#endif
#ifdef CONFIG_ARCH_OMAP16XX
# ifdef OMAP_NAME
-# undef MULTI_OMAP
-# define MULTI_OMAP
+# undef MULTI_OMAP1
+# define MULTI_OMAP1
# else
-# define OMAP_NAME omap1610
+# define OMAP_NAME omap16xx
# endif
#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-# ifdef OMAP_NAME
-# undef MULTI_OMAP
-# define MULTI_OMAP
+#ifdef CONFIG_ARCH_OMAP24XX
+# if (defined(OMAP_NAME) || defined(MULTI_OMAP1))
+# error "OMAP1 and OMAP2 can't be selected at the same time"
# else
-# define OMAP_NAME omap1710
+# undef MULTI_OMAP2
+# define OMAP_NAME omap24xx
# endif
#endif
/*
- * Generate various OMAP cpu specific macros, and cpu class
- * specific macros
+ * Macros to group OMAP into cpu classes.
+ * These can be used in most places.
+ * cpu_is_omap7xx(): True for OMAP730
+ * cpu_is_omap15xx(): True for OMAP1510 and OMAP5910
+ * cpu_is_omap16xx(): True for OMAP1610, OMAP5912 and OMAP1710
+ * cpu_is_omap24xx(): True for OMAP2420
*/
-#define GET_OMAP_TYPE ((system_rev >> 24) & 0xff)
#define GET_OMAP_CLASS (system_rev & 0xff)
-#define IS_OMAP_TYPE(type, id) \
-static inline int is_omap ##type (void) \
-{ \
- return (GET_OMAP_TYPE == (id)) ? 1 : 0; \
-}
-
#define IS_OMAP_CLASS(class, id) \
static inline int is_omap ##class (void) \
{ \
return (GET_OMAP_CLASS == (id)) ? 1 : 0; \
}
-IS_OMAP_TYPE(730, 0x07)
-IS_OMAP_TYPE(1510, 0x15)
-IS_OMAP_TYPE(1610, 0x16)
-IS_OMAP_TYPE(5912, 0x16)
-IS_OMAP_TYPE(1710, 0x17)
-IS_OMAP_TYPE(2420, 0x24)
-
IS_OMAP_CLASS(7xx, 0x07)
IS_OMAP_CLASS(15xx, 0x15)
IS_OMAP_CLASS(16xx, 0x16)
IS_OMAP_CLASS(24xx, 0x24)
-/*
- * Macros to group OMAP types into cpu classes.
- * These can be used in most places.
- * cpu_is_omap15xx(): True for 1510 and 5910
- * cpu_is_omap16xx(): True for 1610, 5912 and 1710
- */
-#if defined(MULTI_OMAP)
-# define cpu_is_omap7xx() is_omap7xx()
-# define cpu_is_omap15xx() is_omap15xx()
-# if !(defined(CONFIG_ARCH_OMAP1510) || defined(CONFIG_ARCH_OMAP730))
-# define cpu_is_omap16xx() 1
-# else
+#define cpu_is_omap7xx() 0
+#define cpu_is_omap15xx() 0
+#define cpu_is_omap16xx() 0
+#define cpu_is_omap24xx() 0
+
+#if defined(MULTI_OMAP1)
+# if defined(CONFIG_ARCH_OMAP730)
+# undef cpu_is_omap7xx
+# define cpu_is_omap7xx() is_omap7xx()
+# endif
+# if defined(CONFIG_ARCH_OMAP1510)
+# undef cpu_is_omap15xx
+# define cpu_is_omap15xx() is_omap15xx()
+# endif
+# if defined(CONFIG_ARCH_OMAP16XX)
+# undef cpu_is_omap16xx
# define cpu_is_omap16xx() is_omap16xx()
# endif
#else
# if defined(CONFIG_ARCH_OMAP730)
+# undef cpu_is_omap7xx
# define cpu_is_omap7xx() 1
-# else
-# define cpu_is_omap7xx() 0
# endif
# if defined(CONFIG_ARCH_OMAP1510)
+# undef cpu_is_omap15xx
# define cpu_is_omap15xx() 1
-# else
-# define cpu_is_omap15xx() 0
# endif
# if defined(CONFIG_ARCH_OMAP16XX)
+# undef cpu_is_omap16xx
# define cpu_is_omap16xx() 1
-# else
-# define cpu_is_omap16xx() 0
+# endif
+# if defined(CONFIG_ARCH_OMAP24XX)
+# undef cpu_is_omap24xx
+# define cpu_is_omap24xx() 1
# endif
#endif
-#if defined(MULTI_OMAP)
-# define cpu_is_omap730() is_omap730()
-# define cpu_is_omap1510() is_omap1510()
-# define cpu_is_omap1610() is_omap1610()
-# define cpu_is_omap5912() is_omap5912()
-# define cpu_is_omap1710() is_omap1710()
-#else
+/*
+ * Macros to detect individual cpu types.
+ * These are only rarely needed.
+ * cpu_is_omap730(): True for OMAP730
+ * cpu_is_omap1510(): True for OMAP1510
+ * cpu_is_omap1610(): True for OMAP1610
+ * cpu_is_omap1611(): True for OMAP1611
+ * cpu_is_omap5912(): True for OMAP5912
+ * cpu_is_omap1621(): True for OMAP1621
+ * cpu_is_omap1710(): True for OMAP1710
+ * cpu_is_omap2420(): True for OMAP2420
+ */
+#define GET_OMAP_TYPE ((system_rev >> 16) & 0xffff)
+
+#define IS_OMAP_TYPE(type, id) \
+static inline int is_omap ##type (void) \
+{ \
+ return (GET_OMAP_TYPE == (id)) ? 1 : 0; \
+}
+
+IS_OMAP_TYPE(730, 0x0730)
+IS_OMAP_TYPE(1510, 0x1510)
+IS_OMAP_TYPE(1610, 0x1610)
+IS_OMAP_TYPE(1611, 0x1611)
+IS_OMAP_TYPE(5912, 0x1611)
+IS_OMAP_TYPE(1621, 0x1621)
+IS_OMAP_TYPE(1710, 0x1710)
+IS_OMAP_TYPE(2420, 0x2420)
+
+#define cpu_is_omap730() 0
+#define cpu_is_omap1510() 0
+#define cpu_is_omap1610() 0
+#define cpu_is_omap5912() 0
+#define cpu_is_omap1611() 0
+#define cpu_is_omap1621() 0
+#define cpu_is_omap1710() 0
+#define cpu_is_omap2420() 0
+
+#if defined(MULTI_OMAP1)
# if defined(CONFIG_ARCH_OMAP730)
-# define cpu_is_omap730() 1
-# else
-# define cpu_is_omap730() 0
+# undef cpu_is_omap730
+# define cpu_is_omap730() is_omap730()
# endif
# if defined(CONFIG_ARCH_OMAP1510)
+# undef cpu_is_omap1510
+# define cpu_is_omap1510() is_omap1510()
+# endif
+#else
+# if defined(CONFIG_ARCH_OMAP730)
+# undef cpu_is_omap730
+# define cpu_is_omap730() 1
+# endif
+# if defined(CONFIG_ARCH_OMAP1510)
+# undef cpu_is_omap1510
# define cpu_is_omap1510() 1
-# else
-# define cpu_is_omap1510() 0
# endif
-# if defined(CONFIG_ARCH_OMAP16XX)
-# define cpu_is_omap1610() 1
-# else
-# define cpu_is_omap1610() 0
-# endif
-# if defined(CONFIG_ARCH_OMAP16XX)
-# define cpu_is_omap5912() 1
-# else
-# define cpu_is_omap5912() 0
-# endif
-# if defined(CONFIG_ARCH_OMAP16XX)
+#endif
+
+/*
+ * Whether we have MULTI_OMAP1 or not, we still need to distinguish
+ * between 1611B/5912 and 1710.
+ */
+#if defined(CONFIG_ARCH_OMAP16XX)
+# undef cpu_is_omap1610
+# undef cpu_is_omap1611
+# undef cpu_is_omap5912
+# undef cpu_is_omap1621
+# undef cpu_is_omap1710
# define cpu_is_omap1610() is_omap1610()
+# define cpu_is_omap1611() is_omap1611()
# define cpu_is_omap5912() is_omap5912()
+# define cpu_is_omap1621() is_omap1621()
# define cpu_is_omap1710() is_omap1710()
-# else
-# define cpu_is_omap1610() 0
-# define cpu_is_omap5912() 0
-# define cpu_is_omap1710() 0
-# endif
-# if defined(CONFIG_ARCH_OMAP2420)
+#endif
+
+#if defined(CONFIG_ARCH_OMAP2420)
+# undef cpu_is_omap2420
# define cpu_is_omap2420() 1
-# else
-# define cpu_is_omap2420() 0
-# endif
#endif
#endif
diff --git a/include/asm-arm/arch-omap/debug-macro.S b/include/asm-arm/arch-omap/debug-macro.S
index 83bb458..ca4f577 100644
--- a/include/asm-arm/arch-omap/debug-macro.S
+++ b/include/asm-arm/arch-omap/debug-macro.S
@@ -14,6 +14,7 @@
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
tst \rx, #1 @ MMU enabled?
+#ifdef CONFIG_ARCH_OMAP1
moveq \rx, #0xff000000 @ physical base address
movne \rx, #0xfe000000 @ virtual base
orr \rx, \rx, #0x00fb0000
@@ -23,6 +24,18 @@
#if defined(CONFIG_OMAP_LL_DEBUG_UART2) || defined(CONFIG_OMAP_LL_DEBUG_UART3)
orr \rx, \rx, #0x00000800 @ UART 2 & 3
#endif
+
+#elif CONFIG_ARCH_OMAP2
+ moveq \rx, #0x48000000 @ physical base address
+ movne \rx, #0xd8000000 @ virtual base
+ orr \rx, \rx, #0x0006a000
+#ifdef CONFIG_OMAP_LL_DEBUG_UART2
+ add \rx, \rx, #0x00002000 @ UART 2
+#endif
+#ifdef CONFIG_OMAP_LL_DEBUG_UART3
+ add \rx, \rx, #0x00004000 @ UART 3
+#endif
+#endif
.endm
.macro senduart,rd,rx
diff --git a/include/asm-arm/arch-omap/dma.h b/include/asm-arm/arch-omap/dma.h
index ce114ce..04ebef5 100644
--- a/include/asm-arm/arch-omap/dma.h
+++ b/include/asm-arm/arch-omap/dma.h
@@ -240,6 +240,7 @@
extern dma_addr_t omap_get_dma_src_pos(int lch);
extern dma_addr_t omap_get_dma_dst_pos(int lch);
+extern int omap_get_dma_src_addr_counter(int lch);
extern void omap_clear_dma(int lch);
extern int omap_dma_running(void);
diff --git a/include/asm-arm/arch-omap/dmtimer.h b/include/asm-arm/arch-omap/dmtimer.h
new file mode 100644
index 0000000..11772c7
--- /dev/null
+++ b/include/asm-arm/arch-omap/dmtimer.h
@@ -0,0 +1,92 @@
+/*
+ * linux/include/asm-arm/arm/arch-omap/dmtimer.h
+ *
+ * OMAP Dual-Mode Timers
+ *
+ * Copyright (C) 2005 Nokia Corporation
+ * Author: Lauri Leukkunen <lauri.leukkunen@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ASM_ARCH_TIMER_H
+#define __ASM_ARCH_TIMER_H
+
+#include <linux/list.h>
+
+#define OMAP_TIMER_SRC_ARMXOR 0x00
+#define OMAP_TIMER_SRC_32_KHZ 0x01
+#define OMAP_TIMER_SRC_EXT_CLK 0x02
+
+/* timer control reg bits */
+#define OMAP_TIMER_CTRL_CAPTMODE (1 << 13)
+#define OMAP_TIMER_CTRL_PT (1 << 12)
+#define OMAP_TIMER_CTRL_TRG_OVERFLOW (0x1 << 10)
+#define OMAP_TIMER_CTRL_TRG_OFANDMATCH (0x2 << 10)
+#define OMAP_TIMER_CTRL_TCM_LOWTOHIGH (0x1 << 8)
+#define OMAP_TIMER_CTRL_TCM_HIGHTOLOW (0x2 << 8)
+#define OMAP_TIMER_CTRL_TCM_BOTHEDGES (0x3 << 8)
+#define OMAP_TIMER_CTRL_SCPWM (1 << 7)
+#define OMAP_TIMER_CTRL_CE (1 << 6) /* compare enable */
+#define OMAP_TIMER_CTRL_PRE (1 << 5) /* prescaler enable */
+#define OMAP_TIMER_CTRL_PTV_SHIFT 2 /* how much to shift the prescaler value */
+#define OMAP_TIMER_CTRL_AR (1 << 1) /* auto-reload enable */
+#define OMAP_TIMER_CTRL_ST (1 << 0) /* start timer */
+
+/* timer interrupt enable bits */
+#define OMAP_TIMER_INT_CAPTURE (1 << 2)
+#define OMAP_TIMER_INT_OVERFLOW (1 << 1)
+#define OMAP_TIMER_INT_MATCH (1 << 0)
+
+
+struct omap_dm_timer {
+ struct list_head timer_list;
+
+ u32 base;
+ unsigned int irq;
+};
+
+u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, int reg);
+void omap_dm_timer_write_reg(struct omap_dm_timer *timer, int reg, u32 value);
+
+struct omap_dm_timer * omap_dm_timer_request(void);
+void omap_dm_timer_free(struct omap_dm_timer *timer);
+void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source);
+
+void omap_dm_timer_set_int_enable(struct omap_dm_timer *timer, unsigned int value);
+void omap_dm_timer_set_trigger(struct omap_dm_timer *timer, unsigned int value);
+void omap_dm_timer_enable_compare(struct omap_dm_timer *timer);
+void omap_dm_timer_enable_autoreload(struct omap_dm_timer *timer);
+
+void omap_dm_timer_trigger(struct omap_dm_timer *timer);
+void omap_dm_timer_start(struct omap_dm_timer *timer);
+void omap_dm_timer_stop(struct omap_dm_timer *timer);
+
+void omap_dm_timer_set_load(struct omap_dm_timer *timer, unsigned int load);
+void omap_dm_timer_set_match(struct omap_dm_timer *timer, unsigned int match);
+
+unsigned int omap_dm_timer_read_status(struct omap_dm_timer *timer);
+void omap_dm_timer_write_status(struct omap_dm_timer *timer, unsigned int value);
+
+unsigned int omap_dm_timer_read_counter(struct omap_dm_timer *timer);
+void omap_dm_timer_reset_counter(struct omap_dm_timer *timer);
+
+int omap_dm_timers_active(void);
+
+#endif /* __ASM_ARCH_TIMER_H */
diff --git a/include/asm-arm/arch-omap/dsp.h b/include/asm-arm/arch-omap/dsp.h
new file mode 100644
index 0000000..57bf4f3
--- /dev/null
+++ b/include/asm-arm/arch-omap/dsp.h
@@ -0,0 +1,244 @@
+/*
+ * linux/include/asm-arm/arch-omap/dsp.h
+ *
+ * Header for OMAP DSP driver
+ *
+ * Copyright (C) 2002-2005 Nokia Corporation
+ *
+ * Written by Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * 2005/06/01: DSP Gateway version 3.3
+ */
+
+#ifndef ASM_ARCH_DSP_H
+#define ASM_ARCH_DSP_H
+
+
+/*
+ * for /dev/dspctl/ctl
+ */
+#define OMAP_DSP_IOCTL_RESET 1
+#define OMAP_DSP_IOCTL_RUN 2
+#define OMAP_DSP_IOCTL_SETRSTVECT 3
+#define OMAP_DSP_IOCTL_CPU_IDLE 4
+#define OMAP_DSP_IOCTL_MPUI_WORDSWAP_ON 5
+#define OMAP_DSP_IOCTL_MPUI_WORDSWAP_OFF 6
+#define OMAP_DSP_IOCTL_MPUI_BYTESWAP_ON 7
+#define OMAP_DSP_IOCTL_MPUI_BYTESWAP_OFF 8
+#define OMAP_DSP_IOCTL_GBL_IDLE 9
+#define OMAP_DSP_IOCTL_DSPCFG 10
+#define OMAP_DSP_IOCTL_DSPUNCFG 11
+#define OMAP_DSP_IOCTL_TASKCNT 12
+#define OMAP_DSP_IOCTL_POLL 13
+#define OMAP_DSP_IOCTL_REGMEMR 40
+#define OMAP_DSP_IOCTL_REGMEMW 41
+#define OMAP_DSP_IOCTL_REGIOR 42
+#define OMAP_DSP_IOCTL_REGIOW 43
+#define OMAP_DSP_IOCTL_GETVAR 44
+#define OMAP_DSP_IOCTL_SETVAR 45
+#define OMAP_DSP_IOCTL_RUNLEVEL 50
+#define OMAP_DSP_IOCTL_SUSPEND 51
+#define OMAP_DSP_IOCTL_RESUME 52
+#define OMAP_DSP_IOCTL_FBEN 53
+#define OMAP_DSP_IOCTL_FBDIS 54
+#define OMAP_DSP_IOCTL_MBSEND 99
+
+/*
+ * for taskdev
+ * (ioctls below should be >= 0x10000)
+ */
+#define OMAP_DSP_TASK_IOCTL_BFLSH 0x10000
+#define OMAP_DSP_TASK_IOCTL_SETBSZ 0x10001
+#define OMAP_DSP_TASK_IOCTL_LOCK 0x10002
+#define OMAP_DSP_TASK_IOCTL_UNLOCK 0x10003
+#define OMAP_DSP_TASK_IOCTL_GETNAME 0x10004
+
+/*
+ * for /dev/dspctl/mem
+ */
+#define OMAP_DSP_MEM_IOCTL_EXMAP 1
+#define OMAP_DSP_MEM_IOCTL_EXUNMAP 2
+#define OMAP_DSP_MEM_IOCTL_EXMAP_FLUSH 3
+#define OMAP_DSP_MEM_IOCTL_FBEXPORT 5
+#define OMAP_DSP_MEM_IOCTL_MMUITACK 7
+#define OMAP_DSP_MEM_IOCTL_MMUINIT 9
+#define OMAP_DSP_MEM_IOCTL_KMEM_RESERVE 11
+#define OMAP_DSP_MEM_IOCTL_KMEM_RELEASE 12
+
+struct omap_dsp_mapinfo {
+ unsigned long dspadr;
+ unsigned long size;
+};
+
+/*
+ * for /dev/dspctl/twch
+ */
+#define OMAP_DSP_TWCH_IOCTL_MKDEV 1
+#define OMAP_DSP_TWCH_IOCTL_RMDEV 2
+#define OMAP_DSP_TWCH_IOCTL_TADD 11
+#define OMAP_DSP_TWCH_IOCTL_TDEL 12
+#define OMAP_DSP_TWCH_IOCTL_TKILL 13
+
+#define OMAP_DSP_DEVSTATE_NOTASK 0x00000001
+#define OMAP_DSP_DEVSTATE_ATTACHED 0x00000002
+#define OMAP_DSP_DEVSTATE_GARBAGE 0x00000004
+#define OMAP_DSP_DEVSTATE_INVALID 0x00000008
+#define OMAP_DSP_DEVSTATE_ADDREQ 0x00000100
+#define OMAP_DSP_DEVSTATE_DELREQ 0x00000200
+#define OMAP_DSP_DEVSTATE_ADDFAIL 0x00001000
+#define OMAP_DSP_DEVSTATE_ADDING 0x00010000
+#define OMAP_DSP_DEVSTATE_DELING 0x00020000
+#define OMAP_DSP_DEVSTATE_KILLING 0x00040000
+#define OMAP_DSP_DEVSTATE_STATE_MASK 0x7fffffff
+#define OMAP_DSP_DEVSTATE_STALE 0x80000000
+
+struct omap_dsp_taddinfo {
+ unsigned char minor;
+ unsigned long taskadr;
+};
+#define OMAP_DSP_TADD_ABORTADR 0xffffffff
+
+
+/*
+ * error cause definition (for error detection device)
+ */
+#define OMAP_DSP_ERRDT_WDT 0x00000001
+#define OMAP_DSP_ERRDT_MMU 0x00000002
+
+
+/*
+ * mailbox protocol definitions
+ */
+
+struct omap_dsp_mailbox_cmd {
+ unsigned short cmd;
+ unsigned short data;
+};
+
+struct omap_dsp_reginfo {
+ unsigned short adr;
+ unsigned short val;
+};
+
+struct omap_dsp_varinfo {
+ unsigned char varid;
+ unsigned short val[0];
+};
+
+#define OMAP_DSP_MBPROT_REVISION 0x0019
+
+#define OMAP_DSP_MBCMD_WDSND 0x10
+#define OMAP_DSP_MBCMD_WDREQ 0x11
+#define OMAP_DSP_MBCMD_BKSND 0x20
+#define OMAP_DSP_MBCMD_BKREQ 0x21
+#define OMAP_DSP_MBCMD_BKYLD 0x23
+#define OMAP_DSP_MBCMD_BKSNDP 0x24
+#define OMAP_DSP_MBCMD_BKREQP 0x25
+#define OMAP_DSP_MBCMD_TCTL 0x30
+#define OMAP_DSP_MBCMD_TCTLDATA 0x31
+#define OMAP_DSP_MBCMD_POLL 0x32
+#define OMAP_DSP_MBCMD_WDT 0x50 /* v3.3: obsolete */
+#define OMAP_DSP_MBCMD_RUNLEVEL 0x51
+#define OMAP_DSP_MBCMD_PM 0x52
+#define OMAP_DSP_MBCMD_SUSPEND 0x53
+#define OMAP_DSP_MBCMD_KFUNC 0x54
+#define OMAP_DSP_MBCMD_TCFG 0x60
+#define OMAP_DSP_MBCMD_TADD 0x62
+#define OMAP_DSP_MBCMD_TDEL 0x63
+#define OMAP_DSP_MBCMD_TSTOP 0x65
+#define OMAP_DSP_MBCMD_DSPCFG 0x70
+#define OMAP_DSP_MBCMD_REGRW 0x72
+#define OMAP_DSP_MBCMD_GETVAR 0x74
+#define OMAP_DSP_MBCMD_SETVAR 0x75
+#define OMAP_DSP_MBCMD_ERR 0x78
+#define OMAP_DSP_MBCMD_DBG 0x79
+
+#define OMAP_DSP_MBCMD_TCTL_TINIT 0x0000
+#define OMAP_DSP_MBCMD_TCTL_TEN 0x0001
+#define OMAP_DSP_MBCMD_TCTL_TDIS 0x0002
+#define OMAP_DSP_MBCMD_TCTL_TCLR 0x0003
+#define OMAP_DSP_MBCMD_TCTL_TCLR_FORCE 0x0004
+
+#define OMAP_DSP_MBCMD_RUNLEVEL_USER 0x01
+#define OMAP_DSP_MBCMD_RUNLEVEL_SUPER 0x0e
+#define OMAP_DSP_MBCMD_RUNLEVEL_RECOVERY 0x10
+
+#define OMAP_DSP_MBCMD_PM_DISABLE 0x00
+#define OMAP_DSP_MBCMD_PM_ENABLE 0x01
+
+#define OMAP_DSP_MBCMD_KFUNC_FBCTL 0x00
+
+#define OMAP_DSP_MBCMD_FBCTL_ENABLE 0x0002
+#define OMAP_DSP_MBCMD_FBCTL_DISABLE 0x0003
+
+#define OMAP_DSP_MBCMD_TDEL_SAFE 0x0000
+#define OMAP_DSP_MBCMD_TDEL_KILL 0x0001
+
+#define OMAP_DSP_MBCMD_DSPCFG_REQ 0x00
+#define OMAP_DSP_MBCMD_DSPCFG_SYSADRH 0x28
+#define OMAP_DSP_MBCMD_DSPCFG_SYSADRL 0x29
+#define OMAP_DSP_MBCMD_DSPCFG_PROTREV 0x70
+#define OMAP_DSP_MBCMD_DSPCFG_ABORT 0x78
+#define OMAP_DSP_MBCMD_DSPCFG_LAST 0x80
+
+#define OMAP_DSP_MBCMD_REGRW_MEMR 0x00
+#define OMAP_DSP_MBCMD_REGRW_MEMW 0x01
+#define OMAP_DSP_MBCMD_REGRW_IOR 0x02
+#define OMAP_DSP_MBCMD_REGRW_IOW 0x03
+#define OMAP_DSP_MBCMD_REGRW_DATA 0x04
+
+#define OMAP_DSP_MBCMD_VARID_ICRMASK 0x00
+#define OMAP_DSP_MBCMD_VARID_LOADINFO 0x01
+
+#define OMAP_DSP_TTYP_ARCV 0x0001
+#define OMAP_DSP_TTYP_ASND 0x0002
+#define OMAP_DSP_TTYP_BKMD 0x0004
+#define OMAP_DSP_TTYP_BKDM 0x0008
+#define OMAP_DSP_TTYP_PVMD 0x0010
+#define OMAP_DSP_TTYP_PVDM 0x0020
+
+#define OMAP_DSP_EID_BADTID 0x10
+#define OMAP_DSP_EID_BADTCN 0x11
+#define OMAP_DSP_EID_BADBID 0x20
+#define OMAP_DSP_EID_BADCNT 0x21
+#define OMAP_DSP_EID_NOTLOCKED 0x22
+#define OMAP_DSP_EID_STVBUF 0x23
+#define OMAP_DSP_EID_BADADR 0x24
+#define OMAP_DSP_EID_BADTCTL 0x30
+#define OMAP_DSP_EID_BADPARAM 0x50
+#define OMAP_DSP_EID_FATAL 0x58
+#define OMAP_DSP_EID_NOMEM 0xc0
+#define OMAP_DSP_EID_NORES 0xc1
+#define OMAP_DSP_EID_IPBFULL 0xc2
+#define OMAP_DSP_EID_WDT 0xd0
+#define OMAP_DSP_EID_TASKNOTRDY 0xe0
+#define OMAP_DSP_EID_TASKBSY 0xe1
+#define OMAP_DSP_EID_TASKERR 0xef
+#define OMAP_DSP_EID_BADCFGTYP 0xf0
+#define OMAP_DSP_EID_DEBUG 0xf8
+#define OMAP_DSP_EID_BADSEQ 0xfe
+#define OMAP_DSP_EID_BADCMD 0xff
+
+#define OMAP_DSP_TNM_LEN 16
+
+#define OMAP_DSP_TID_FREE 0xff
+#define OMAP_DSP_TID_ANON 0xfe
+
+#define OMAP_DSP_BID_NULL 0xffff
+#define OMAP_DSP_BID_PVT 0xfffe
+
+#endif /* ASM_ARCH_DSP_H */
diff --git a/include/asm-arm/arch-omap/dsp_common.h b/include/asm-arm/arch-omap/dsp_common.h
new file mode 100644
index 0000000..4fcce69
--- /dev/null
+++ b/include/asm-arm/arch-omap/dsp_common.h
@@ -0,0 +1,37 @@
+/*
+ * linux/include/asm-arm/arch-omap/dsp_common.h
+ *
+ * Header for OMAP DSP subsystem control
+ *
+ * Copyright (C) 2004,2005 Nokia Corporation
+ *
+ * Written by Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * 2005/06/03: DSP Gateway version 3.3
+ */
+
+#ifndef ASM_ARCH_DSP_COMMON_H
+#define ASM_ARCH_DSP_COMMON_H
+
+void omap_dsp_pm_suspend(void);
+void omap_dsp_pm_resume(void);
+void omap_dsp_request_mpui(void);
+void omap_dsp_release_mpui(void);
+int omap_dsp_request_mem(void);
+int omap_dsp_release_mem(void);
+
+#endif /* ASM_ARCH_DSP_COMMON_H */
diff --git a/include/asm-arm/arch-omap/entry-macro.S b/include/asm-arm/arch-omap/entry-macro.S
index 57b1268..0d29b9c 100644
--- a/include/asm-arm/arch-omap/entry-macro.S
+++ b/include/asm-arm/arch-omap/entry-macro.S
@@ -8,6 +8,8 @@
* warranty of any kind, whether express or implied.
*/
+#if defined(CONFIG_ARCH_OMAP1)
+
.macro disable_fiq
.endm
@@ -30,3 +32,29 @@
1510:
.endm
+#elif defined(CONFIG_ARCH_OMAP24XX)
+
+#include <asm/arch/omap24xx.h>
+
+ .macro disable_fiq
+ .endm
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+ ldr \base, =VA_IC_BASE
+ ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
+ cmp \irqnr, #0x0
+ bne 2222f
+ ldr \irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
+ cmp \irqnr, #0x0
+ bne 2222f
+ ldr \irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
+ cmp \irqnr, #0x0
+2222:
+ ldrne \irqnr, [\base, #IRQ_SIR_IRQ]
+
+ .endm
+
+ .macro irq_prio_table
+ .endm
+
+#endif
diff --git a/include/asm-arm/arch-omap/gpio.h b/include/asm-arm/arch-omap/gpio.h
index fad2fc9..74cb2b9 100644
--- a/include/asm-arm/arch-omap/gpio.h
+++ b/include/asm-arm/arch-omap/gpio.h
@@ -3,7 +3,7 @@
*
* OMAP GPIO handling defines and functions
*
- * Copyright (C) 2003 Nokia Corporation
+ * Copyright (C) 2003-2005 Nokia Corporation
*
* Written by Juha Yrjölä <juha.yrjola@nokia.com>
*
@@ -30,7 +30,23 @@
#include <asm/arch/irqs.h>
#include <asm/io.h>
-#define OMAP_MPUIO_BASE 0xfffb5000
+#define OMAP_MPUIO_BASE (void __iomem *)0xfffb5000
+
+#ifdef CONFIG_ARCH_OMAP730
+#define OMAP_MPUIO_INPUT_LATCH 0x00
+#define OMAP_MPUIO_OUTPUT 0x02
+#define OMAP_MPUIO_IO_CNTL 0x04
+#define OMAP_MPUIO_KBR_LATCH 0x08
+#define OMAP_MPUIO_KBC 0x0a
+#define OMAP_MPUIO_GPIO_EVENT_MODE 0x0c
+#define OMAP_MPUIO_GPIO_INT_EDGE 0x0e
+#define OMAP_MPUIO_KBD_INT 0x10
+#define OMAP_MPUIO_GPIO_INT 0x12
+#define OMAP_MPUIO_KBD_MASKIT 0x14
+#define OMAP_MPUIO_GPIO_MASKIT 0x16
+#define OMAP_MPUIO_GPIO_DEBOUNCING 0x18
+#define OMAP_MPUIO_LATCH 0x1a
+#else
#define OMAP_MPUIO_INPUT_LATCH 0x00
#define OMAP_MPUIO_OUTPUT 0x04
#define OMAP_MPUIO_IO_CNTL 0x08
@@ -44,6 +60,7 @@
#define OMAP_MPUIO_GPIO_MASKIT 0x2c
#define OMAP_MPUIO_GPIO_DEBOUNCING 0x30
#define OMAP_MPUIO_LATCH 0x34
+#endif
#define OMAP_MPUIO(nr) (OMAP_MAX_GPIO_LINES + (nr))
#define OMAP_GPIO_IS_MPUIO(nr) ((nr) >= OMAP_MAX_GPIO_LINES)
@@ -52,18 +69,11 @@
IH_MPUIO_BASE + ((nr) & 0x0f) : \
IH_GPIO_BASE + ((nr) & 0x3f))
-/* For EDGECTRL */
-#define OMAP_GPIO_NO_EDGE 0x00
-#define OMAP_GPIO_FALLING_EDGE 0x01
-#define OMAP_GPIO_RISING_EDGE 0x02
-#define OMAP_GPIO_BOTH_EDGES 0x03
-
extern int omap_gpio_init(void); /* Call from board init only */
extern int omap_request_gpio(int gpio);
extern void omap_free_gpio(int gpio);
extern void omap_set_gpio_direction(int gpio, int is_input);
extern void omap_set_gpio_dataout(int gpio, int enable);
extern int omap_get_gpio_datain(int gpio);
-extern void omap_set_gpio_edge_ctrl(int gpio, int edge);
#endif
diff --git a/include/asm-arm/arch-omap/hardware.h b/include/asm-arm/arch-omap/hardware.h
index 48258c7..60201e1 100644
--- a/include/asm-arm/arch-omap/hardware.h
+++ b/include/asm-arm/arch-omap/hardware.h
@@ -43,6 +43,7 @@
#include <asm/arch/cpu.h>
#endif
#include <asm/arch/io.h>
+#include <asm/arch/serial.h>
/*
* ---------------------------------------------------------------------------
@@ -89,11 +90,12 @@
/* DPLL control registers */
#define DPLL_CTL (0xfffecf00)
-/* DSP clock control */
+/* DSP clock control. Must use __raw_readw() and __raw_writew() with these */
#define DSP_CONFIG_REG_BASE (0xe1008000)
#define DSP_CKCTL (DSP_CONFIG_REG_BASE + 0x0)
#define DSP_IDLECT1 (DSP_CONFIG_REG_BASE + 0x4)
#define DSP_IDLECT2 (DSP_CONFIG_REG_BASE + 0x8)
+#define DSP_RSTCT2 (DSP_CONFIG_REG_BASE + 0x14)
/*
* ---------------------------------------------------------------------------
@@ -142,6 +144,13 @@
* Interrupts
* ---------------------------------------------------------------------------
*/
+#ifdef CONFIG_ARCH_OMAP1
+
+/*
+ * XXX: These probably want to be moved to arch/arm/mach-omap/omap1/irq.c
+ * or something similar.. -- PFM.
+ */
+
#define OMAP_IH1_BASE 0xfffecb00
#define OMAP_IH2_BASE 0xfffe0000
@@ -170,6 +179,8 @@
#define IRQ_ILR0_REG_OFFSET 0x1c
#define IRQ_GMR_REG_OFFSET 0xa0
+#endif
+
/*
* ----------------------------------------------------------------------------
* System control registers
@@ -260,32 +271,17 @@
/*
* ---------------------------------------------------------------------------
- * Serial ports
- * ---------------------------------------------------------------------------
- */
-#define OMAP_UART1_BASE (unsigned char *)0xfffb0000
-#define OMAP_UART2_BASE (unsigned char *)0xfffb0800
-#define OMAP_UART3_BASE (unsigned char *)0xfffb9800
-#define OMAP_MAX_NR_PORTS 3
-#define OMAP1510_BASE_BAUD (12000000/16)
-#define OMAP16XX_BASE_BAUD (48000000/16)
-
-#define is_omap_port(p) ({int __ret = 0; \
- if (p == IO_ADDRESS(OMAP_UART1_BASE) || \
- p == IO_ADDRESS(OMAP_UART2_BASE) || \
- p == IO_ADDRESS(OMAP_UART3_BASE)) \
- __ret = 1; \
- __ret; \
- })
-
-/*
- * ---------------------------------------------------------------------------
* Processor specific defines
* ---------------------------------------------------------------------------
*/
#include "omap730.h"
#include "omap1510.h"
+
+#ifdef CONFIG_ARCH_OMAP24XX
+#include "omap24xx.h"
+#endif
+
#include "omap16xx.h"
/*
@@ -312,7 +308,6 @@
#ifdef CONFIG_MACH_OMAP_H4
#include "board-h4.h"
-#error "Support for H4 board not yet implemented."
#endif
#ifdef CONFIG_MACH_OMAP_OSK
diff --git a/include/asm-arm/arch-omap/io.h b/include/asm-arm/arch-omap/io.h
index 1c8c9fc..11fbf62 100644
--- a/include/asm-arm/arch-omap/io.h
+++ b/include/asm-arm/arch-omap/io.h
@@ -49,16 +49,24 @@
* I/O mapping
* ----------------------------------------------------------------------------
*/
-#define IO_PHYS 0xFFFB0000
-#define IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
-#define IO_VIRT (IO_PHYS - IO_OFFSET)
-#define IO_SIZE 0x40000
-#define IO_ADDRESS(x) ((x) - IO_OFFSET)
-#define PCIO_BASE 0
+#if defined(CONFIG_ARCH_OMAP1)
+#define IO_PHYS 0xFFFB0000
+#define IO_OFFSET -0x01000000 /* Virtual IO = 0xfefb0000 */
+#define IO_SIZE 0x40000
-#define io_p2v(x) ((x) - IO_OFFSET)
-#define io_v2p(x) ((x) + IO_OFFSET)
+#elif defined(CONFIG_ARCH_OMAP2)
+#define IO_PHYS 0x48000000 /* L4 peripherals; other stuff has to be mapped *
+ * manually. */
+#define IO_OFFSET 0x90000000 /* Virtual IO = 0xd8000000 */
+#define IO_SIZE 0x08000000
+#endif
+
+#define IO_VIRT (IO_PHYS + IO_OFFSET)
+#define IO_ADDRESS(x) ((x) + IO_OFFSET)
+#define PCIO_BASE 0
+#define io_p2v(x) ((x) + IO_OFFSET)
+#define io_v2p(x) ((x) - IO_OFFSET)
#ifndef __ASSEMBLER__
@@ -96,6 +104,8 @@
->offset[((vaddr)&4095)>>2]
#define __REG32(paddr) __REGV32(io_p2v(paddr))
+extern void omap_map_common_io(void);
+
#else
#define __REG8(paddr) io_p2v(paddr)
diff --git a/include/asm-arm/arch-omap/irqs.h b/include/asm-arm/arch-omap/irqs.h
index 0d05a7c..74e108c 100644
--- a/include/asm-arm/arch-omap/irqs.h
+++ b/include/asm-arm/arch-omap/irqs.h
@@ -135,7 +135,6 @@
/*
* OMAP-1510 specific IRQ numbers for interrupt handler 2
*/
-#define INT_1510_OS_32kHz_TIMER (22 + IH2_BASE)
#define INT_1510_COM_SPI_RO (31 + IH2_BASE)
/*
@@ -232,6 +231,11 @@
#define INT_730_DMA_CH15 (62 + IH2_BASE)
#define INT_730_NAND (63 + IH2_BASE)
+#define INT_24XX_GPIO_BANK1 29
+#define INT_24XX_GPIO_BANK2 30
+#define INT_24XX_GPIO_BANK3 31
+#define INT_24XX_GPIO_BANK4 32
+
/* Max. 128 level 2 IRQs (OMAP1610), 192 GPIOs (OMAP730) and
* 16 MPUIO lines */
#define OMAP_MAX_GPIO_LINES 192
diff --git a/include/asm-arm/arch-omap/memory.h b/include/asm-arm/arch-omap/memory.h
index f6b57dd..84f81e3 100644
--- a/include/asm-arm/arch-omap/memory.h
+++ b/include/asm-arm/arch-omap/memory.h
@@ -36,12 +36,11 @@
/*
* Physical DRAM offset.
*/
+#if defined(CONFIG_ARCH_OMAP1)
#define PHYS_OFFSET (0x10000000UL)
-
-/*
- * OMAP-1510 Local Bus address offset
- */
-#define OMAP1510_LB_OFFSET (0x30000000UL)
+#elif defined(CONFIG_ARCH_OMAP2)
+#define PHYS_OFFSET (0x80000000UL)
+#endif
/*
* Conversion between SDRAM and fake PCI bus, used by USB
@@ -64,6 +63,11 @@
*/
#ifdef CONFIG_ARCH_OMAP1510
+/*
+ * OMAP-1510 Local Bus address offset
+ */
+#define OMAP1510_LB_OFFSET (0x30000000UL)
+
#define virt_to_lbus(x) ((x) - PAGE_OFFSET + OMAP1510_LB_OFFSET)
#define lbus_to_virt(x) ((x) - OMAP1510_LB_OFFSET + PAGE_OFFSET)
#define is_lbus_device(dev) (cpu_is_omap1510() && dev && (strncmp(dev->bus_id, "ohci", 4) == 0))
diff --git a/include/asm-arm/arch-omap/mtd-xip.h b/include/asm-arm/arch-omap/mtd-xip.h
new file mode 100644
index 0000000..a73a285
--- /dev/null
+++ b/include/asm-arm/arch-omap/mtd-xip.h
@@ -0,0 +1,61 @@
+/*
+ * MTD primitives for XIP support. Architecture specific functions.
+ *
+ * Do not include this file directly. It's included from linux/mtd/xip.h
+ *
+ * Author: Vladimir Barinov <vbarinov@ru.mvista.com>
+ *
+ * (c) 2005 MontaVista Software, Inc. This file is licensed under the
+ * terms of the GNU General Public License version 2. This program is
+ * licensed "as is" without any warranty of any kind, whether express or
+ * implied.
+ */
+
+#ifndef __ARCH_OMAP_MTD_XIP_H__
+#define __ARCH_OMAP_MTD_XIP_H__
+
+#include <asm/hardware.h>
+#define OMAP_MPU_TIMER_BASE (0xfffec500)
+#define OMAP_MPU_TIMER_OFFSET 0x100
+
+typedef struct {
+ u32 cntl; /* CNTL_TIMER, R/W */
+ u32 load_tim; /* LOAD_TIM, W */
+ u32 read_tim; /* READ_TIM, R */
+} xip_omap_mpu_timer_regs_t;
+
+#define xip_omap_mpu_timer_base(n) \
+((volatile xip_omap_mpu_timer_regs_t*)IO_ADDRESS(OMAP_MPU_TIMER_BASE + \
+ (n)*OMAP_MPU_TIMER_OFFSET))
+
+static inline unsigned long xip_omap_mpu_timer_read(int nr)
+{
+ volatile xip_omap_mpu_timer_regs_t* timer = xip_omap_mpu_timer_base(nr);
+ return timer->read_tim;
+}
+
+#define xip_irqpending() \
+ (omap_readl(OMAP_IH1_ITR) & ~omap_readl(OMAP_IH1_MIR))
+#define xip_currtime() (~xip_omap_mpu_timer_read(0))
+
+/*
+ * It's permitted to do approxmation for xip_elapsed_since macro
+ * (see linux/mtd/xip.h)
+ */
+
+#ifdef CONFIG_MACH_OMAP_PERSEUS2
+#define xip_elapsed_since(x) (signed)((~xip_omap_mpu_timer_read(0) - (x)) / 7)
+#else
+#define xip_elapsed_since(x) (signed)((~xip_omap_mpu_timer_read(0) - (x)) / 6)
+#endif
+
+/*
+ * xip_cpu_idle() is used when waiting for a delay equal or larger than
+ * the system timer tick period. This should put the CPU into idle mode
+ * to save power and to be woken up only when some interrupts are pending.
+ * As above, this should not rely upon standard kernel code.
+ */
+
+#define xip_cpu_idle() asm volatile ("mcr p15, 0, %0, c7, c0, 4" :: "r" (1))
+
+#endif /* __ARCH_OMAP_MTD_XIP_H__ */
diff --git a/include/asm-arm/arch-omap/mux.h b/include/asm-arm/arch-omap/mux.h
index 5bd3f00..1b1ad41 100644
--- a/include/asm-arm/arch-omap/mux.h
+++ b/include/asm-arm/arch-omap/mux.h
@@ -185,6 +185,7 @@
/* MPUIO */
MPUIO2,
+ N15_1610_MPUIO2,
MPUIO4,
MPUIO5,
T20_1610_MPUIO5,
@@ -210,6 +211,7 @@
/* Misc ballouts */
BALLOUT_V8_ARMIO3,
+ N20_HDQ,
/* OMAP-1610 MMC2 */
W8_1610_MMC2_DAT0,
@@ -235,6 +237,7 @@
P20_1610_GPIO4,
V9_1610_GPIO7,
W8_1610_GPIO9,
+ N20_1610_GPIO11,
N19_1610_GPIO13,
P10_1610_GPIO22,
V5_1610_GPIO24,
@@ -250,7 +253,7 @@
U18_1610_UWIRE_SDI,
W21_1610_UWIRE_SDO,
N14_1610_UWIRE_CS0,
- P15_1610_UWIRE_CS0,
+ P15_1610_UWIRE_CS3,
N15_1610_UWIRE_CS1,
/* OMAP-1610 Flash */
@@ -411,7 +414,8 @@
MUX_CFG("W15_1710_GPIO40", 9, 27, 7, 2, 5, 1, 2, 1, 1)
/* MPUIO */
-MUX_CFG("MPUIO2", 7, 18, 0, 1, 1, 1, NA, 0, 1)
+MUX_CFG("MPUIO2", 7, 18, 0, 1, 14, 1, NA, 0, 1)
+MUX_CFG("N15_1610_MPUIO2", 7, 18, 0, 1, 14, 1, 1, 0, 1)
MUX_CFG("MPUIO4", 7, 15, 0, 1, 13, 1, NA, 0, 1)
MUX_CFG("MPUIO5", 7, 12, 0, 1, 12, 1, NA, 0, 1)
@@ -438,6 +442,7 @@
/* Misc ballouts */
MUX_CFG("BALLOUT_V8_ARMIO3", B, 18, 0, 2, 25, 1, NA, 0, 1)
+MUX_CFG("N20_HDQ", 6, 18, 1, 1, 4, 0, 1, 4, 0)
/* OMAP-1610 MMC2 */
MUX_CFG("W8_1610_MMC2_DAT0", B, 21, 6, 2, 23, 1, 2, 1, 1)
@@ -463,6 +468,7 @@
MUX_CFG("P20_1610_GPIO4", 6, 27, 0, 1, 7, 0, 1, 1, 1)
MUX_CFG("V9_1610_GPIO7", B, 12, 1, 2, 20, 0, 2, 1, 1)
MUX_CFG("W8_1610_GPIO9", B, 21, 0, 2, 23, 0, 2, 1, 1)
+MUX_CFG("N20_1610_GPIO11", 6, 18, 0, 1, 4, 0, 1, 1, 1)
MUX_CFG("N19_1610_GPIO13", 6, 12, 0, 1, 2, 0, 1, 1, 1)
MUX_CFG("P10_1610_GPIO22", C, 0, 7, 2, 26, 0, 2, 1, 1)
MUX_CFG("V5_1610_GPIO24", B, 15, 7, 2, 21, 0, 2, 1, 1)
diff --git a/include/asm-arm/arch-omap/omap1510.h b/include/asm-arm/arch-omap/omap1510.h
index f491a48..f086a39 100644
--- a/include/asm-arm/arch-omap/omap1510.h
+++ b/include/asm-arm/arch-omap/omap1510.h
@@ -36,10 +36,6 @@
/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
-#define OMAP1510_SRAM_BASE 0xD0000000
-#define OMAP1510_SRAM_SIZE (SZ_128K + SZ_64K)
-#define OMAP1510_SRAM_START 0x20000000
-
#define OMAP1510_DSP_BASE 0xE0000000
#define OMAP1510_DSP_SIZE 0x28000
#define OMAP1510_DSP_START 0xE0000000
@@ -48,14 +44,5 @@
#define OMAP1510_DSPREG_SIZE SZ_128K
#define OMAP1510_DSPREG_START 0xE1000000
-/*
- * ----------------------------------------------------------------------------
- * Memory used by power management
- * ----------------------------------------------------------------------------
- */
-
-#define OMAP1510_SRAM_IDLE_SUSPEND (OMAP1510_SRAM_BASE + OMAP1510_SRAM_SIZE - 0x200)
-#define OMAP1510_SRAM_API_SUSPEND (OMAP1510_SRAM_IDLE_SUSPEND + 0x100)
-
#endif /* __ASM_ARCH_OMAP1510_H */
diff --git a/include/asm-arm/arch-omap/omap16xx.h b/include/asm-arm/arch-omap/omap16xx.h
index 38a9b95..f0c7f0f 100644
--- a/include/asm-arm/arch-omap/omap16xx.h
+++ b/include/asm-arm/arch-omap/omap16xx.h
@@ -36,11 +36,6 @@
/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
-#define OMAP16XX_SRAM_BASE 0xD0000000
-#define OMAP1610_SRAM_SIZE (SZ_16K)
-#define OMAP5912_SRAM_SIZE 0x3E800
-#define OMAP16XX_SRAM_START 0x20000000
-
#define OMAP16XX_DSP_BASE 0xE0000000
#define OMAP16XX_DSP_SIZE 0x28000
#define OMAP16XX_DSP_START 0xE0000000
@@ -50,17 +45,6 @@
#define OMAP16XX_DSPREG_START 0xE1000000
/*
- * ----------------------------------------------------------------------------
- * Memory used by power management
- * ----------------------------------------------------------------------------
- */
-
-#define OMAP1610_SRAM_IDLE_SUSPEND (OMAP16XX_SRAM_BASE + OMAP1610_SRAM_SIZE - 0x200)
-#define OMAP1610_SRAM_API_SUSPEND (OMAP1610_SRAM_IDLE_SUSPEND + 0x100)
-#define OMAP5912_SRAM_IDLE_SUSPEND (OMAP16XX_SRAM_BASE + OMAP5912_SRAM_SIZE - 0x200)
-#define OMAP5912_SRAM_API_SUSPEND (OMAP5912_SRAM_IDLE_SUSPEND + 0x100)
-
-/*
* ---------------------------------------------------------------------------
* Interrupts
* ---------------------------------------------------------------------------
diff --git a/include/asm-arm/arch-omap/omap24xx.h b/include/asm-arm/arch-omap/omap24xx.h
new file mode 100644
index 0000000..a910546
--- /dev/null
+++ b/include/asm-arm/arch-omap/omap24xx.h
@@ -0,0 +1,15 @@
+#ifndef __ASM_ARCH_OMAP24XX_H
+#define __ASM_ARCH_OMAP24XX_H
+
+#define OMAP24XX_L4_IO_BASE 0x48000000
+
+/* interrupt controller */
+#define OMAP24XX_IC_BASE (OMAP24XX_L4_IO_BASE + 0xfe000)
+#define VA_IC_BASE IO_ADDRESS(OMAP24XX_IC_BASE)
+
+#define OMAP24XX_IVA_INTC_BASE 0x40000000
+
+#define IRQ_SIR_IRQ 0x0040
+
+#endif /* __ASM_ARCH_OMAP24XX_H */
+
diff --git a/include/asm-arm/arch-omap/omap730.h b/include/asm-arm/arch-omap/omap730.h
index 599ab00..755b64c 100644
--- a/include/asm-arm/arch-omap/omap730.h
+++ b/include/asm-arm/arch-omap/omap730.h
@@ -36,10 +36,6 @@
/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
-#define OMAP730_SRAM_BASE 0xD0000000
-#define OMAP730_SRAM_SIZE (SZ_128K + SZ_64K + SZ_8K)
-#define OMAP730_SRAM_START 0x20000000
-
#define OMAP730_DSP_BASE 0xE0000000
#define OMAP730_DSP_SIZE 0x50000
#define OMAP730_DSP_START 0xE0000000
diff --git a/include/asm-arm/arch-omap/pm.h b/include/asm-arm/arch-omap/pm.h
index f209fc0..fbd742d 100644
--- a/include/asm-arm/arch-omap/pm.h
+++ b/include/asm-arm/arch-omap/pm.h
@@ -61,7 +61,10 @@
#define PER_EN 0x1
#define CPU_SUSPEND_SIZE 200
-#define ULPD_LOW_POWER_EN 0x0001
+#define ULPD_LOW_PWR_EN 0x0001
+#define ULPD_DEEP_SLEEP_TRANSITION_EN 0x0010
+#define ULPD_SETUP_ANALOG_CELL_3_VAL 0
+#define ULPD_POWER_CTRL_REG_VAL 0x0219
#define DSP_IDLE_DELAY 10
#define DSP_IDLE 0x0040
@@ -86,46 +89,35 @@
#define OMAP1510_BIG_SLEEP_REQUEST 0x0cc5
#define OMAP1510_IDLE_LOOP_REQUEST 0x0c00
#define OMAP1510_IDLE_CLOCK_DOMAINS 0x2
-#define OMAP1510_ULPD_LOW_POWER_REQ 0x0001
-#define OMAP1610_DEEP_SLEEP_REQUEST 0x17c7
-#define OMAP1610_BIG_SLEEP_REQUEST TBD
+/* Both big sleep and deep sleep use same values. Difference is in ULPD. */
+#define OMAP1610_IDLECT1_SLEEP_VAL 0x13c7
+#define OMAP1610_IDLECT2_SLEEP_VAL 0x09c7
+#define OMAP1610_IDLECT3_VAL 0x3f
+#define OMAP1610_IDLECT3_SLEEP_ORMASK 0x2c
+#define OMAP1610_IDLECT3 0xfffece24
#define OMAP1610_IDLE_LOOP_REQUEST 0x0400
-#define OMAP1610_IDLE_CLOCK_DOMAINS 0x09c7
-#define OMAP1610_ULPD_LOW_POWER_REQ 0x3
-
-#ifndef OMAP1510_SRAM_IDLE_SUSPEND
-#define OMAP1510_SRAM_IDLE_SUSPEND 0
-#endif
-#ifndef OMAP1610_SRAM_IDLE_SUSPEND
-#define OMAP1610_SRAM_IDLE_SUSPEND 0
-#endif
-#ifndef OMAP5912_SRAM_IDLE_SUSPEND
-#define OMAP5912_SRAM_IDLE_SUSPEND 0
-#endif
-
-#ifndef OMAP1510_SRAM_API_SUSPEND
-#define OMAP1510_SRAM_API_SUSPEND 0
-#endif
-#ifndef OMAP1610_SRAM_API_SUSPEND
-#define OMAP1610_SRAM_API_SUSPEND 0
-#endif
-#ifndef OMAP5912_SRAM_API_SUSPEND
-#define OMAP5912_SRAM_API_SUSPEND 0
-#endif
#if !defined(CONFIG_ARCH_OMAP1510) && \
- !defined(CONFIG_ARCH_OMAP16XX)
+ !defined(CONFIG_ARCH_OMAP16XX) && \
+ !defined(CONFIG_ARCH_OMAP24XX)
#error "Power management for this processor not implemented yet"
#endif
#ifndef __ASSEMBLER__
extern void omap_pm_idle(void);
extern void omap_pm_suspend(void);
-extern int omap1510_cpu_suspend(unsigned short, unsigned short);
-extern int omap1610_cpu_suspend(unsigned short, unsigned short);
-extern int omap1510_idle_loop_suspend(void);
-extern int omap1610_idle_loop_suspend(void);
+extern void omap1510_cpu_suspend(unsigned short, unsigned short);
+extern void omap1610_cpu_suspend(unsigned short, unsigned short);
+extern void omap1510_idle_loop_suspend(void);
+extern void omap1610_idle_loop_suspend(void);
+
+#ifdef CONFIG_OMAP_SERIAL_WAKE
+extern void omap_serial_wake_trigger(int enable);
+#else
+#define omap_serial_wake_trigger(x) {}
+#endif /* CONFIG_OMAP_SERIAL_WAKE */
+
extern unsigned int omap1510_cpu_suspend_sz;
extern unsigned int omap1510_idle_loop_suspend_sz;
extern unsigned int omap1610_cpu_suspend_sz;
@@ -161,6 +153,7 @@
ARM_SLEEP_SAVE_ARM_CKCTL,
ARM_SLEEP_SAVE_ARM_IDLECT1,
ARM_SLEEP_SAVE_ARM_IDLECT2,
+ ARM_SLEEP_SAVE_ARM_IDLECT3,
ARM_SLEEP_SAVE_ARM_EWUPCT,
ARM_SLEEP_SAVE_ARM_RSTCT1,
ARM_SLEEP_SAVE_ARM_RSTCT2,
diff --git a/include/asm-arm/arch-omap/serial.h b/include/asm-arm/arch-omap/serial.h
new file mode 100644
index 0000000..79a5297
--- /dev/null
+++ b/include/asm-arm/arch-omap/serial.h
@@ -0,0 +1,37 @@
+/*
+ * linux/include/asm-arm/arch-omap/serial.h
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARCH_SERIAL_H
+#define __ASM_ARCH_SERIAL_H
+
+#if defined(CONFIG_ARCH_OMAP1)
+/* OMAP1 serial ports */
+#define OMAP_UART1_BASE 0xfffb0000
+#define OMAP_UART2_BASE 0xfffb0800
+#define OMAP_UART3_BASE 0xfffb9800
+#elif defined(CONFIG_ARCH_OMAP2)
+/* OMAP2 serial ports */
+#define OMAP_UART1_BASE 0x4806a000
+#define OMAP_UART2_BASE 0x4806c000
+#define OMAP_UART3_BASE 0x4806e000
+#endif
+
+#define OMAP_MAX_NR_PORTS 3
+#define OMAP1510_BASE_BAUD (12000000/16)
+#define OMAP16XX_BASE_BAUD (48000000/16)
+
+#define is_omap_port(p) ({int __ret = 0; \
+ if (p == IO_ADDRESS(OMAP_UART1_BASE) || \
+ p == IO_ADDRESS(OMAP_UART2_BASE) || \
+ p == IO_ADDRESS(OMAP_UART3_BASE)) \
+ __ret = 1; \
+ __ret; \
+ })
+
+#endif
diff --git a/include/asm-arm/arch-omap/uncompress.h b/include/asm-arm/arch-omap/uncompress.h
index 3e640ab..3545c86 100644
--- a/include/asm-arm/arch-omap/uncompress.h
+++ b/include/asm-arm/arch-omap/uncompress.h
@@ -20,7 +20,7 @@
#include <linux/config.h>
#include <linux/types.h>
#include <linux/serial_reg.h>
-#include <asm/arch/hardware.h>
+#include <asm/arch/serial.h>
unsigned int system_rev;
@@ -34,8 +34,9 @@
putstr(const char *s)
{
volatile u8 * uart = 0;
- int shift;
+ int shift = 2;
+#ifdef CONFIG_ARCH_OMAP
#ifdef CONFIG_OMAP_LL_DEBUG_UART3
uart = (volatile u8 *)(OMAP_UART3_BASE);
#elif CONFIG_OMAP_LL_DEBUG_UART2
@@ -44,6 +45,7 @@
uart = (volatile u8 *)(OMAP_UART1_BASE);
#endif
+#ifdef CONFIG_ARCH_OMAP1
/* Determine which serial port to use */
do {
/* MMU is not on, so cpu_is_omapXXXX() won't work here */
@@ -51,14 +53,14 @@
if (omap_id == OMAP_ID_730)
shift = 0;
- else
- shift = 2;
if (check_port(uart, shift))
break;
/* Silent boot if no serial ports are enabled. */
return;
} while (0);
+#endif /* CONFIG_ARCH_OMAP1 */
+#endif
/*
* Now, xmit each character