diff --git a/Documentation/scsi/NinjaSCSI.txt b/Documentation/scsi/NinjaSCSI.txt
index 17dd547..73cec12 100644
--- a/Documentation/scsi/NinjaSCSI.txt
+++ b/Documentation/scsi/NinjaSCSI.txt
@@ -59,10 +59,10 @@
 ...
 $ make
 
-[5] Copy nsp_cs.o to suitable plase, like /lib/modules/<Kernel version>/pcmcia/ .
+[5] Copy nsp_cs.ko to suitable place, like /lib/modules/<Kernel version>/pcmcia/ .
 
 [6] Add these lines to /etc/pcmcia/config .
-    If you yse pcmcia-cs-3.1.8 or later, we can use "nsp_cs.conf" file.
+    If you use pcmcia-cs-3.1.8 or later, we can use "nsp_cs.conf" file.
     So, you don't need to edit file. Just copy to /etc/pcmcia/ .
 
 -------------------------------------
diff --git a/Documentation/scsi/aic79xx.txt b/Documentation/scsi/aic79xx.txt
index 382b439..2084ad5 100644
--- a/Documentation/scsi/aic79xx.txt
+++ b/Documentation/scsi/aic79xx.txt
@@ -94,7 +94,7 @@
         - Add support for scsi_report_device_reset() found in
           2.5.X kernels.
         - Add 7901B support.
-        - Simplify handling of the packtized lun Rev A workaround.
+        - Simplify handling of the packetized lun Rev A workaround.
         - Correct and simplify handling of the ignore wide residue
           message.  The previous code would fail to report a residual
           if the transaction data length was even and we received
diff --git a/Documentation/scsi/dc395x.txt b/Documentation/scsi/dc395x.txt
index ae3b79a..88219f9 100644
--- a/Documentation/scsi/dc395x.txt
+++ b/Documentation/scsi/dc395x.txt
@@ -20,7 +20,7 @@
 ----------
 The driver uses the settings from the EEPROM set in the SCSI BIOS 
 setup. If there is no EEPROM, the driver uses default values.
-Both can be overriden by command line parameters (module or kernel
+Both can be overridden by command line parameters (module or kernel
 parameters).
 
 The following parameters are available:
diff --git a/Documentation/scsi/ibmmca.txt b/Documentation/scsi/ibmmca.txt
index a783635..9b95163 100644
--- a/Documentation/scsi/ibmmca.txt
+++ b/Documentation/scsi/ibmmca.txt
@@ -1086,7 +1086,7 @@
    
      Q: "Reset SCSI-devices at boottime" halts the system at boottime, why?
      A: This is only tested with the IBM SCSI Adapter w/cache. It is not
-        yet prooved to run on other adapters, however you may be lucky.
+        yet proven to run on other adapters, however you may be lucky.
 	In version 3.1d this has been hugely improved and should work better,
 	now. Normally you really won't need to activate this flag in the
 	kernel configuration, as all post 1989 SCSI-devices should accept
diff --git a/Documentation/scsi/ncr53c8xx.txt b/Documentation/scsi/ncr53c8xx.txt
index 29cbbb6..ea8e98f 100644
--- a/Documentation/scsi/ncr53c8xx.txt
+++ b/Documentation/scsi/ncr53c8xx.txt
@@ -631,8 +631,8 @@
 
 A boot setup command for the ncr53c8xx (sym53c8xx) driver begins with the 
 driver name "ncr53c8xx="(sym53c8xx). The kernel syntax parser then expects 
-an optionnal list of integers separated with comma followed by an optional 
-list of  comma-separated strings. Example of boot setup command under lilo 
+an optional list of integers separated with comma followed by an optional 
+list of comma-separated strings. Example of boot setup command under lilo 
 prompt:
 
 lilo: linux root=/dev/hda2 ncr53c8xx=tags:4,sync:10,debug:0x200
@@ -899,7 +899,7 @@
     ncr53c8xx=safe:y,mpar:y
     ncr53c8xx=safe:y
 
-My personnal system works flawlessly with the following equivalent setup:
+My personal system works flawlessly with the following equivalent setup:
 
    ncr53c8xx=mpar:y,spar:y,disc:y,specf:1,fsn:n,ultra:2,fsn:n,revprob:n,verb:1\
              tags:32,sync:12,debug:0,burst:7,led:1,wide:1,settle:2,diff:0,irqm:0
diff --git a/Documentation/scsi/scsi-changer.txt b/Documentation/scsi/scsi-changer.txt
index c132687..d74bbd2 100644
--- a/Documentation/scsi/scsi-changer.txt
+++ b/Documentation/scsi/scsi-changer.txt
@@ -31,7 +31,7 @@
   media transport - this one shuffles around the media, i.e. the
                     transport arm.  Also known as "picker".
   storage         - a slot which can hold a media.
-  import/export   - the same as above, but is accessable from outside,
+  import/export   - the same as above, but is accessible from outside,
                     i.e. there the operator (you !) can use this to
                     fill in and remove media from the changer.
 		    Sometimes named "mailslot".