| /* Copyright 2003 Tungsten Graphics, Inc., Cedar Park, Texas. |
| * All Rights Reserved. |
| * |
| * Permission is hereby granted, free of charge, to any person obtaining a |
| * copy of this software and associated documentation files (the |
| * "Software"), to deal in the Software without restriction, including |
| * without limitation the rights to use, copy, modify, merge, publish, |
| * distribute, sub license, and/or sell copies of the Software, and to |
| * permit persons to whom the Software is furnished to do so, subject to |
| * the following conditions: |
| * |
| * The above copyright notice and this permission notice (including the |
| * next paragraph) shall be included in all copies or substantial portions |
| * of the Software. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS |
| * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. |
| * IN NO EVENT SHALL TUNGSTEN GRAPHICS AND/OR ITS SUPPLIERS BE LIABLE FOR |
| * ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, |
| * TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE |
| * SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. |
| */ |
| |
| #ifndef _I915_REG_H_ |
| #define _I915_REG_H_ |
| |
| #define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a))) |
| |
| #define _PORT(port, a, b) ((a) + (port)*((b)-(a))) |
| |
| #define _MASKED_BIT_ENABLE(a) (((a) << 16) | (a)) |
| #define _MASKED_BIT_DISABLE(a) ((a) << 16) |
| |
| /* |
| * The Bridge device's PCI config space has information about the |
| * fb aperture size and the amount of pre-reserved memory. |
| * This is all handled in the intel-gtt.ko module. i915.ko only |
| * cares about the vga bit for the vga rbiter. |
| */ |
| #define INTEL_GMCH_CTRL 0x52 |
| #define INTEL_GMCH_VGA_DISABLE (1 << 1) |
| |
| /* PCI config space */ |
| |
| #define HPLLCC 0xc0 /* 855 only */ |
| #define GC_CLOCK_CONTROL_MASK (0xf << 0) |
| #define GC_CLOCK_133_200 (0 << 0) |
| #define GC_CLOCK_100_200 (1 << 0) |
| #define GC_CLOCK_100_133 (2 << 0) |
| #define GC_CLOCK_166_250 (3 << 0) |
| #define GCFGC2 0xda |
| #define GCFGC 0xf0 /* 915+ only */ |
| #define GC_LOW_FREQUENCY_ENABLE (1 << 7) |
| #define GC_DISPLAY_CLOCK_190_200_MHZ (0 << 4) |
| #define GC_DISPLAY_CLOCK_333_MHZ (4 << 4) |
| #define GC_DISPLAY_CLOCK_MASK (7 << 4) |
| #define GM45_GC_RENDER_CLOCK_MASK (0xf << 0) |
| #define GM45_GC_RENDER_CLOCK_266_MHZ (8 << 0) |
| #define GM45_GC_RENDER_CLOCK_320_MHZ (9 << 0) |
| #define GM45_GC_RENDER_CLOCK_400_MHZ (0xb << 0) |
| #define GM45_GC_RENDER_CLOCK_533_MHZ (0xc << 0) |
| #define I965_GC_RENDER_CLOCK_MASK (0xf << 0) |
| #define I965_GC_RENDER_CLOCK_267_MHZ (2 << 0) |
| #define I965_GC_RENDER_CLOCK_333_MHZ (3 << 0) |
| #define I965_GC_RENDER_CLOCK_444_MHZ (4 << 0) |
| #define I965_GC_RENDER_CLOCK_533_MHZ (5 << 0) |
| #define I945_GC_RENDER_CLOCK_MASK (7 << 0) |
| #define I945_GC_RENDER_CLOCK_166_MHZ (0 << 0) |
| #define I945_GC_RENDER_CLOCK_200_MHZ (1 << 0) |
| #define I945_GC_RENDER_CLOCK_250_MHZ (3 << 0) |
| #define I945_GC_RENDER_CLOCK_400_MHZ (5 << 0) |
| #define I915_GC_RENDER_CLOCK_MASK (7 << 0) |
| #define I915_GC_RENDER_CLOCK_166_MHZ (0 << 0) |
| #define I915_GC_RENDER_CLOCK_200_MHZ (1 << 0) |
| #define I915_GC_RENDER_CLOCK_333_MHZ (4 << 0) |
| #define LBB 0xf4 |
| |
| /* Graphics reset regs */ |
| #define I965_GDRST 0xc0 /* PCI config register */ |
| #define ILK_GDSR 0x2ca4 /* MCHBAR offset */ |
| #define GRDOM_FULL (0<<2) |
| #define GRDOM_RENDER (1<<2) |
| #define GRDOM_MEDIA (3<<2) |
| #define GRDOM_RESET_ENABLE (1<<0) |
| |
| #define GEN6_MBCUNIT_SNPCR 0x900c /* for LLC config */ |
| #define GEN6_MBC_SNPCR_SHIFT 21 |
| #define GEN6_MBC_SNPCR_MASK (3<<21) |
| #define GEN6_MBC_SNPCR_MAX (0<<21) |
| #define GEN6_MBC_SNPCR_MED (1<<21) |
| #define GEN6_MBC_SNPCR_LOW (2<<21) |
| #define GEN6_MBC_SNPCR_MIN (3<<21) /* only 1/16th of the cache is shared */ |
| |
| #define GEN6_MBCTL 0x0907c |
| #define GEN6_MBCTL_ENABLE_BOOT_FETCH (1 << 4) |
| #define GEN6_MBCTL_CTX_FETCH_NEEDED (1 << 3) |
| #define GEN6_MBCTL_BME_UPDATE_ENABLE (1 << 2) |
| #define GEN6_MBCTL_MAE_UPDATE_ENABLE (1 << 1) |
| #define GEN6_MBCTL_BOOT_FETCH_MECH (1 << 0) |
| |
| #define GEN6_GDRST 0x941c |
| #define GEN6_GRDOM_FULL (1 << 0) |
| #define GEN6_GRDOM_RENDER (1 << 1) |
| #define GEN6_GRDOM_MEDIA (1 << 2) |
| #define GEN6_GRDOM_BLT (1 << 3) |
| |
| /* PPGTT stuff */ |
| #define GEN6_GTT_ADDR_ENCODE(addr) ((addr) | (((addr) >> 28) & 0xff0)) |
| |
| #define GEN6_PDE_VALID (1 << 0) |
| #define GEN6_PDE_LARGE_PAGE (2 << 0) /* use 32kb pages */ |
| /* gen6+ has bit 11-4 for physical addr bit 39-32 */ |
| #define GEN6_PDE_ADDR_ENCODE(addr) GEN6_GTT_ADDR_ENCODE(addr) |
| |
| #define GEN6_PTE_VALID (1 << 0) |
| #define GEN6_PTE_UNCACHED (1 << 1) |
| #define GEN6_PTE_CACHE_LLC (2 << 1) |
| #define GEN6_PTE_CACHE_LLC_MLC (3 << 1) |
| #define GEN6_PTE_CACHE_BITS (3 << 1) |
| #define GEN6_PTE_GFDT (1 << 3) |
| #define GEN6_PTE_ADDR_ENCODE(addr) GEN6_GTT_ADDR_ENCODE(addr) |
| |
| #define RING_PP_DIR_BASE(ring) ((ring)->mmio_base+0x228) |
| #define RING_PP_DIR_BASE_READ(ring) ((ring)->mmio_base+0x518) |
| #define RING_PP_DIR_DCLV(ring) ((ring)->mmio_base+0x220) |
| #define PP_DIR_DCLV_2G 0xffffffff |
| |
| #define GAM_ECOCHK 0x4090 |
| #define ECOCHK_SNB_BIT (1<<10) |
| #define ECOCHK_PPGTT_CACHE64B (0x3<<3) |
| #define ECOCHK_PPGTT_CACHE4B (0x0<<3) |
| |
| #define GAC_ECO_BITS 0x14090 |
| #define ECOBITS_PPGTT_CACHE64B (3<<8) |
| #define ECOBITS_PPGTT_CACHE4B (0<<8) |
| |
| #define GAB_CTL 0x24000 |
| #define GAB_CTL_CONT_AFTER_PAGEFAULT (1<<8) |
| |
| /* VGA stuff */ |
| |
| #define VGA_ST01_MDA 0x3ba |
| #define VGA_ST01_CGA 0x3da |
| |
| #define VGA_MSR_WRITE 0x3c2 |
| #define VGA_MSR_READ 0x3cc |
| #define VGA_MSR_MEM_EN (1<<1) |
| #define VGA_MSR_CGA_MODE (1<<0) |
| |
| #define VGA_SR_INDEX 0x3c4 |
| #define VGA_SR_DATA 0x3c5 |
| |
| #define VGA_AR_INDEX 0x3c0 |
| #define VGA_AR_VID_EN (1<<5) |
| #define VGA_AR_DATA_WRITE 0x3c0 |
| #define VGA_AR_DATA_READ 0x3c1 |
| |
| #define VGA_GR_INDEX 0x3ce |
| #define VGA_GR_DATA 0x3cf |
| /* GR05 */ |
| #define VGA_GR_MEM_READ_MODE_SHIFT 3 |
| #define VGA_GR_MEM_READ_MODE_PLANE 1 |
| /* GR06 */ |
| #define VGA_GR_MEM_MODE_MASK 0xc |
| #define VGA_GR_MEM_MODE_SHIFT 2 |
| #define VGA_GR_MEM_A0000_AFFFF 0 |
| #define VGA_GR_MEM_A0000_BFFFF 1 |
| #define VGA_GR_MEM_B0000_B7FFF 2 |
| #define VGA_GR_MEM_B0000_BFFFF 3 |
| |
| #define VGA_DACMASK 0x3c6 |
| #define VGA_DACRX 0x3c7 |
| #define VGA_DACWX 0x3c8 |
| #define VGA_DACDATA 0x3c9 |
| |
| #define VGA_CR_INDEX_MDA 0x3b4 |
| #define VGA_CR_DATA_MDA 0x3b5 |
| #define VGA_CR_INDEX_CGA 0x3d4 |
| #define VGA_CR_DATA_CGA 0x3d5 |
| |
| /* |
| * Memory interface instructions used by the kernel |
| */ |
| #define MI_INSTR(opcode, flags) (((opcode) << 23) | (flags)) |
| |
| #define MI_NOOP MI_INSTR(0, 0) |
| #define MI_USER_INTERRUPT MI_INSTR(0x02, 0) |
| #define MI_WAIT_FOR_EVENT MI_INSTR(0x03, 0) |
| #define MI_WAIT_FOR_OVERLAY_FLIP (1<<16) |
| #define MI_WAIT_FOR_PLANE_B_FLIP (1<<6) |
| #define MI_WAIT_FOR_PLANE_A_FLIP (1<<2) |
| #define MI_WAIT_FOR_PLANE_A_SCANLINES (1<<1) |
| #define MI_FLUSH MI_INSTR(0x04, 0) |
| #define MI_READ_FLUSH (1 << 0) |
| #define MI_EXE_FLUSH (1 << 1) |
| #define MI_NO_WRITE_FLUSH (1 << 2) |
| #define MI_SCENE_COUNT (1 << 3) /* just increment scene count */ |
| #define MI_END_SCENE (1 << 4) /* flush binner and incr scene count */ |
| #define MI_INVALIDATE_ISP (1 << 5) /* invalidate indirect state pointers */ |
| #define MI_BATCH_BUFFER_END MI_INSTR(0x0a, 0) |
| #define MI_SUSPEND_FLUSH MI_INSTR(0x0b, 0) |
| #define MI_SUSPEND_FLUSH_EN (1<<0) |
| #define MI_REPORT_HEAD MI_INSTR(0x07, 0) |
| #define MI_OVERLAY_FLIP MI_INSTR(0x11, 0) |
| #define MI_OVERLAY_CONTINUE (0x0<<21) |
| #define MI_OVERLAY_ON (0x1<<21) |
| #define MI_OVERLAY_OFF (0x2<<21) |
| #define MI_LOAD_SCAN_LINES_INCL MI_INSTR(0x12, 0) |
| #define MI_DISPLAY_FLIP MI_INSTR(0x14, 2) |
| #define MI_DISPLAY_FLIP_I915 MI_INSTR(0x14, 1) |
| #define MI_DISPLAY_FLIP_PLANE(n) ((n) << 20) |
| /* IVB has funny definitions for which plane to flip. */ |
| #define MI_DISPLAY_FLIP_IVB_PLANE_A (0 << 19) |
| #define MI_DISPLAY_FLIP_IVB_PLANE_B (1 << 19) |
| #define MI_DISPLAY_FLIP_IVB_SPRITE_A (2 << 19) |
| #define MI_DISPLAY_FLIP_IVB_SPRITE_B (3 << 19) |
| #define MI_DISPLAY_FLIP_IVB_PLANE_C (4 << 19) |
| #define MI_DISPLAY_FLIP_IVB_SPRITE_C (5 << 19) |
| #define MI_ARB_ON_OFF MI_INSTR(0x08, 0) |
| #define MI_ARB_ENABLE (1<<0) |
| #define MI_ARB_DISABLE (0<<0) |
| |
| #define MI_SET_CONTEXT MI_INSTR(0x18, 0) |
| #define MI_MM_SPACE_GTT (1<<8) |
| #define MI_MM_SPACE_PHYSICAL (0<<8) |
| #define MI_SAVE_EXT_STATE_EN (1<<3) |
| #define MI_RESTORE_EXT_STATE_EN (1<<2) |
| #define MI_FORCE_RESTORE (1<<1) |
| #define MI_RESTORE_INHIBIT (1<<0) |
| #define MI_STORE_DWORD_IMM MI_INSTR(0x20, 1) |
| #define MI_MEM_VIRTUAL (1 << 22) /* 965+ only */ |
| #define MI_STORE_DWORD_INDEX MI_INSTR(0x21, 1) |
| #define MI_STORE_DWORD_INDEX_SHIFT 2 |
| /* Official intel docs are somewhat sloppy concerning MI_LOAD_REGISTER_IMM: |
| * - Always issue a MI_NOOP _before_ the MI_LOAD_REGISTER_IMM - otherwise hw |
| * simply ignores the register load under certain conditions. |
| * - One can actually load arbitrary many arbitrary registers: Simply issue x |
| * address/value pairs. Don't overdue it, though, x <= 2^4 must hold! |
| */ |
| #define MI_LOAD_REGISTER_IMM(x) MI_INSTR(0x22, 2*x-1) |
| #define MI_FLUSH_DW MI_INSTR(0x26, 1) /* for GEN6 */ |
| #define MI_INVALIDATE_TLB (1<<18) |
| #define MI_INVALIDATE_BSD (1<<7) |
| #define MI_BATCH_BUFFER MI_INSTR(0x30, 1) |
| #define MI_BATCH_NON_SECURE (1) |
| #define MI_BATCH_NON_SECURE_I965 (1<<8) |
| #define MI_BATCH_BUFFER_START MI_INSTR(0x31, 0) |
| #define MI_BATCH_GTT (2<<6) /* aliased with (1<<7) on gen4 */ |
| #define MI_SEMAPHORE_MBOX MI_INSTR(0x16, 1) /* gen6+ */ |
| #define MI_SEMAPHORE_GLOBAL_GTT (1<<22) |
| #define MI_SEMAPHORE_UPDATE (1<<21) |
| #define MI_SEMAPHORE_COMPARE (1<<20) |
| #define MI_SEMAPHORE_REGISTER (1<<18) |
| #define MI_SEMAPHORE_SYNC_RV (2<<16) |
| #define MI_SEMAPHORE_SYNC_RB (0<<16) |
| #define MI_SEMAPHORE_SYNC_VR (0<<16) |
| #define MI_SEMAPHORE_SYNC_VB (2<<16) |
| #define MI_SEMAPHORE_SYNC_BR (2<<16) |
| #define MI_SEMAPHORE_SYNC_BV (0<<16) |
| #define MI_SEMAPHORE_SYNC_INVALID (1<<0) |
| /* |
| * 3D instructions used by the kernel |
| */ |
| #define GFX_INSTR(opcode, flags) ((0x3 << 29) | ((opcode) << 24) | (flags)) |
| |
| #define GFX_OP_RASTER_RULES ((0x3<<29)|(0x7<<24)) |
| #define GFX_OP_SCISSOR ((0x3<<29)|(0x1c<<24)|(0x10<<19)) |
| #define SC_UPDATE_SCISSOR (0x1<<1) |
| #define SC_ENABLE_MASK (0x1<<0) |
| #define SC_ENABLE (0x1<<0) |
| #define GFX_OP_LOAD_INDIRECT ((0x3<<29)|(0x1d<<24)|(0x7<<16)) |
| #define GFX_OP_SCISSOR_INFO ((0x3<<29)|(0x1d<<24)|(0x81<<16)|(0x1)) |
| #define SCI_YMIN_MASK (0xffff<<16) |
| #define SCI_XMIN_MASK (0xffff<<0) |
| #define SCI_YMAX_MASK (0xffff<<16) |
| #define SCI_XMAX_MASK (0xffff<<0) |
| #define GFX_OP_SCISSOR_ENABLE ((0x3<<29)|(0x1c<<24)|(0x10<<19)) |
| #define GFX_OP_SCISSOR_RECT ((0x3<<29)|(0x1d<<24)|(0x81<<16)|1) |
| #define GFX_OP_COLOR_FACTOR ((0x3<<29)|(0x1d<<24)|(0x1<<16)|0x0) |
| #define GFX_OP_STIPPLE ((0x3<<29)|(0x1d<<24)|(0x83<<16)) |
| #define GFX_OP_MAP_INFO ((0x3<<29)|(0x1d<<24)|0x4) |
| #define GFX_OP_DESTBUFFER_VARS ((0x3<<29)|(0x1d<<24)|(0x85<<16)|0x0) |
| #define GFX_OP_DESTBUFFER_INFO ((0x3<<29)|(0x1d<<24)|(0x8e<<16)|1) |
| #define GFX_OP_DRAWRECT_INFO ((0x3<<29)|(0x1d<<24)|(0x80<<16)|(0x3)) |
| #define GFX_OP_DRAWRECT_INFO_I965 ((0x7900<<16)|0x2) |
| #define SRC_COPY_BLT_CMD ((2<<29)|(0x43<<22)|4) |
| #define XY_SRC_COPY_BLT_CMD ((2<<29)|(0x53<<22)|6) |
| #define XY_MONO_SRC_COPY_IMM_BLT ((2<<29)|(0x71<<22)|5) |
| #define XY_SRC_COPY_BLT_WRITE_ALPHA (1<<21) |
| #define XY_SRC_COPY_BLT_WRITE_RGB (1<<20) |
| #define BLT_DEPTH_8 (0<<24) |
| #define BLT_DEPTH_16_565 (1<<24) |
| #define BLT_DEPTH_16_1555 (2<<24) |
| #define BLT_DEPTH_32 (3<<24) |
| #define BLT_ROP_GXCOPY (0xcc<<16) |
| #define XY_SRC_COPY_BLT_SRC_TILED (1<<15) /* 965+ only */ |
| #define XY_SRC_COPY_BLT_DST_TILED (1<<11) /* 965+ only */ |
| #define CMD_OP_DISPLAYBUFFER_INFO ((0x0<<29)|(0x14<<23)|2) |
| #define ASYNC_FLIP (1<<22) |
| #define DISPLAY_PLANE_A (0<<20) |
| #define DISPLAY_PLANE_B (1<<20) |
| #define GFX_OP_PIPE_CONTROL(len) ((0x3<<29)|(0x3<<27)|(0x2<<24)|(len-2)) |
| #define PIPE_CONTROL_CS_STALL (1<<20) |
| #define PIPE_CONTROL_TLB_INVALIDATE (1<<18) |
| #define PIPE_CONTROL_QW_WRITE (1<<14) |
| #define PIPE_CONTROL_DEPTH_STALL (1<<13) |
| #define PIPE_CONTROL_WRITE_FLUSH (1<<12) |
| #define PIPE_CONTROL_RENDER_TARGET_CACHE_FLUSH (1<<12) /* gen6+ */ |
| #define PIPE_CONTROL_INSTRUCTION_CACHE_INVALIDATE (1<<11) /* MBZ on Ironlake */ |
| #define PIPE_CONTROL_TEXTURE_CACHE_INVALIDATE (1<<10) /* GM45+ only */ |
| #define PIPE_CONTROL_INDIRECT_STATE_DISABLE (1<<9) |
| #define PIPE_CONTROL_NOTIFY (1<<8) |
| #define PIPE_CONTROL_VF_CACHE_INVALIDATE (1<<4) |
| #define PIPE_CONTROL_CONST_CACHE_INVALIDATE (1<<3) |
| #define PIPE_CONTROL_STATE_CACHE_INVALIDATE (1<<2) |
| #define PIPE_CONTROL_STALL_AT_SCOREBOARD (1<<1) |
| #define PIPE_CONTROL_DEPTH_CACHE_FLUSH (1<<0) |
| #define PIPE_CONTROL_GLOBAL_GTT (1<<2) /* in addr dword */ |
| |
| |
| /* |
| * Reset registers |
| */ |
| #define DEBUG_RESET_I830 0x6070 |
| #define DEBUG_RESET_FULL (1<<7) |
| #define DEBUG_RESET_RENDER (1<<8) |
| #define DEBUG_RESET_DISPLAY (1<<9) |
| |
| /* |
| * DPIO - a special bus for various display related registers to hide behind: |
| * 0x800c: m1, m2, n, p1, p2, k dividers |
| * 0x8014: REF and SFR select |
| * 0x8014: N divider, VCO select |
| * 0x801c/3c: core clock bits |
| * 0x8048/68: low pass filter coefficients |
| * 0x8100: fast clock controls |
| */ |
| #define DPIO_PKT 0x2100 |
| #define DPIO_RID (0<<24) |
| #define DPIO_OP_WRITE (1<<16) |
| #define DPIO_OP_READ (0<<16) |
| #define DPIO_PORTID (0x12<<8) |
| #define DPIO_BYTE (0xf<<4) |
| #define DPIO_BUSY (1<<0) /* status only */ |
| #define DPIO_DATA 0x2104 |
| #define DPIO_REG 0x2108 |
| #define DPIO_CTL 0x2110 |
| #define DPIO_MODSEL1 (1<<3) /* if ref clk b == 27 */ |
| #define DPIO_MODSEL0 (1<<2) /* if ref clk a == 27 */ |
| #define DPIO_SFR_BYPASS (1<<1) |
| #define DPIO_RESET (1<<0) |
| |
| #define _DPIO_DIV_A 0x800c |
| #define DPIO_POST_DIV_SHIFT (28) /* 3 bits */ |
| #define DPIO_K_SHIFT (24) /* 4 bits */ |
| #define DPIO_P1_SHIFT (21) /* 3 bits */ |
| #define DPIO_P2_SHIFT (16) /* 5 bits */ |
| #define DPIO_N_SHIFT (12) /* 4 bits */ |
| #define DPIO_ENABLE_CALIBRATION (1<<11) |
| #define DPIO_M1DIV_SHIFT (8) /* 3 bits */ |
| #define DPIO_M2DIV_MASK 0xff |
| #define _DPIO_DIV_B 0x802c |
| #define DPIO_DIV(pipe) _PIPE(pipe, _DPIO_DIV_A, _DPIO_DIV_B) |
| |
| #define _DPIO_REFSFR_A 0x8014 |
| #define DPIO_REFSEL_OVERRIDE 27 |
| #define DPIO_PLL_MODESEL_SHIFT 24 /* 3 bits */ |
| #define DPIO_BIAS_CURRENT_CTL_SHIFT 21 /* 3 bits, always 0x7 */ |
| #define DPIO_PLL_REFCLK_SEL_SHIFT 16 /* 2 bits */ |
| #define DPIO_DRIVER_CTL_SHIFT 12 /* always set to 0x8 */ |
| #define DPIO_CLK_BIAS_CTL_SHIFT 8 /* always set to 0x5 */ |
| #define _DPIO_REFSFR_B 0x8034 |
| #define DPIO_REFSFR(pipe) _PIPE(pipe, _DPIO_REFSFR_A, _DPIO_REFSFR_B) |
| |
| #define _DPIO_CORE_CLK_A 0x801c |
| #define _DPIO_CORE_CLK_B 0x803c |
| #define DPIO_CORE_CLK(pipe) _PIPE(pipe, _DPIO_CORE_CLK_A, _DPIO_CORE_CLK_B) |
| |
| #define _DPIO_LFP_COEFF_A 0x8048 |
| #define _DPIO_LFP_COEFF_B 0x8068 |
| #define DPIO_LFP_COEFF(pipe) _PIPE(pipe, _DPIO_LFP_COEFF_A, _DPIO_LFP_COEFF_B) |
| |
| #define DPIO_FASTCLK_DISABLE 0x8100 |
| |
| /* |
| * Fence registers |
| */ |
| #define FENCE_REG_830_0 0x2000 |
| #define FENCE_REG_945_8 0x3000 |
| #define I830_FENCE_START_MASK 0x07f80000 |
| #define I830_FENCE_TILING_Y_SHIFT 12 |
| #define I830_FENCE_SIZE_BITS(size) ((ffs((size) >> 19) - 1) << 8) |
| #define I830_FENCE_PITCH_SHIFT 4 |
| #define I830_FENCE_REG_VALID (1<<0) |
| #define I915_FENCE_MAX_PITCH_VAL 4 |
| #define I830_FENCE_MAX_PITCH_VAL 6 |
| #define I830_FENCE_MAX_SIZE_VAL (1<<8) |
| |
| #define I915_FENCE_START_MASK 0x0ff00000 |
| #define I915_FENCE_SIZE_BITS(size) ((ffs((size) >> 20) - 1) << 8) |
| |
| #define FENCE_REG_965_0 0x03000 |
| #define I965_FENCE_PITCH_SHIFT 2 |
| #define I965_FENCE_TILING_Y_SHIFT 1 |
| #define I965_FENCE_REG_VALID (1<<0) |
| #define I965_FENCE_MAX_PITCH_VAL 0x0400 |
| |
| #define FENCE_REG_SANDYBRIDGE_0 0x100000 |
| #define SANDYBRIDGE_FENCE_PITCH_SHIFT 32 |
| |
| /* control register for cpu gtt access */ |
| #define TILECTL 0x101000 |
| #define TILECTL_SWZCTL (1 << 0) |
| #define TILECTL_TLB_PREFETCH_DIS (1 << 2) |
| #define TILECTL_BACKSNOOP_DIS (1 << 3) |
| |
| /* |
| * Instruction and interrupt control regs |
| */ |
| #define PGTBL_ER 0x02024 |
| #define RENDER_RING_BASE 0x02000 |
| #define BSD_RING_BASE 0x04000 |
| #define GEN6_BSD_RING_BASE 0x12000 |
| #define BLT_RING_BASE 0x22000 |
| #define RING_TAIL(base) ((base)+0x30) |
| #define RING_HEAD(base) ((base)+0x34) |
| #define RING_START(base) ((base)+0x38) |
| #define RING_CTL(base) ((base)+0x3c) |
| #define RING_SYNC_0(base) ((base)+0x40) |
| #define RING_SYNC_1(base) ((base)+0x44) |
| #define GEN6_RVSYNC (RING_SYNC_0(RENDER_RING_BASE)) |
| #define GEN6_RBSYNC (RING_SYNC_1(RENDER_RING_BASE)) |
| #define GEN6_VRSYNC (RING_SYNC_1(GEN6_BSD_RING_BASE)) |
| #define GEN6_VBSYNC (RING_SYNC_0(GEN6_BSD_RING_BASE)) |
| #define GEN6_BRSYNC (RING_SYNC_0(BLT_RING_BASE)) |
| #define GEN6_BVSYNC (RING_SYNC_1(BLT_RING_BASE)) |
| #define RING_MAX_IDLE(base) ((base)+0x54) |
| #define RING_HWS_PGA(base) ((base)+0x80) |
| #define RING_HWS_PGA_GEN6(base) ((base)+0x2080) |
| #define ARB_MODE 0x04030 |
| #define ARB_MODE_SWIZZLE_SNB (1<<4) |
| #define ARB_MODE_SWIZZLE_IVB (1<<5) |
| #define RENDER_HWS_PGA_GEN7 (0x04080) |
| #define RING_FAULT_REG(ring) (0x4094 + 0x100*(ring)->id) |
| #define DONE_REG 0x40b0 |
| #define BSD_HWS_PGA_GEN7 (0x04180) |
| #define BLT_HWS_PGA_GEN7 (0x04280) |
| #define RING_ACTHD(base) ((base)+0x74) |
| #define RING_NOPID(base) ((base)+0x94) |
| #define RING_IMR(base) ((base)+0xa8) |
| #define RING_TIMESTAMP(base) ((base)+0x358) |
| #define TAIL_ADDR 0x001FFFF8 |
| #define HEAD_WRAP_COUNT 0xFFE00000 |
| #define HEAD_WRAP_ONE 0x00200000 |
| #define HEAD_ADDR 0x001FFFFC |
| #define RING_NR_PAGES 0x001FF000 |
| #define RING_REPORT_MASK 0x00000006 |
| #define RING_REPORT_64K 0x00000002 |
| #define RING_REPORT_128K 0x00000004 |
| #define RING_NO_REPORT 0x00000000 |
| #define RING_VALID_MASK 0x00000001 |
| #define RING_VALID 0x00000001 |
| #define RING_INVALID 0x00000000 |
| #define RING_WAIT_I8XX (1<<0) /* gen2, PRBx_HEAD */ |
| #define RING_WAIT (1<<11) /* gen3+, PRBx_CTL */ |
| #define RING_WAIT_SEMAPHORE (1<<10) /* gen6+ */ |
| #if 0 |
| #define PRB0_TAIL 0x02030 |
| #define PRB0_HEAD 0x02034 |
| #define PRB0_START 0x02038 |
| #define PRB0_CTL 0x0203c |
| #define PRB1_TAIL 0x02040 /* 915+ only */ |
| #define PRB1_HEAD 0x02044 /* 915+ only */ |
| #define PRB1_START 0x02048 /* 915+ only */ |
| #define PRB1_CTL 0x0204c /* 915+ only */ |
| #endif |
| #define IPEIR_I965 0x02064 |
| #define IPEHR_I965 0x02068 |
| #define INSTDONE_I965 0x0206c |
| #define RING_IPEIR(base) ((base)+0x64) |
| #define RING_IPEHR(base) ((base)+0x68) |
| #define RING_INSTDONE(base) ((base)+0x6c) |
| #define RING_INSTPS(base) ((base)+0x70) |
| #define RING_DMA_FADD(base) ((base)+0x78) |
| #define RING_INSTPM(base) ((base)+0xc0) |
| #define INSTPS 0x02070 /* 965+ only */ |
| #define INSTDONE1 0x0207c /* 965+ only */ |
| #define ACTHD_I965 0x02074 |
| #define HWS_PGA 0x02080 |
| #define HWS_ADDRESS_MASK 0xfffff000 |
| #define HWS_START_ADDRESS_SHIFT 4 |
| #define PWRCTXA 0x2088 /* 965GM+ only */ |
| #define PWRCTX_EN (1<<0) |
| #define IPEIR 0x02088 |
| #define IPEHR 0x0208c |
| #define INSTDONE 0x02090 |
| #define NOPID 0x02094 |
| #define HWSTAM 0x02098 |
| #define DMA_FADD_I8XX 0x020d0 |
| |
| #define ERROR_GEN6 0x040a0 |
| |
| /* GM45+ chicken bits -- debug workaround bits that may be required |
| * for various sorts of correct behavior. The top 16 bits of each are |
| * the enables for writing to the corresponding low bit. |
| */ |
| #define _3D_CHICKEN 0x02084 |
| #define _3D_CHICKEN2 0x0208c |
| /* Disables pipelining of read flushes past the SF-WIZ interface. |
| * Required on all Ironlake steppings according to the B-Spec, but the |
| * particular danger of not doing so is not specified. |
| */ |
| # define _3D_CHICKEN2_WM_READ_PIPELINED (1 << 14) |
| #define _3D_CHICKEN3 0x02090 |
| #define _3D_CHICKEN_SF_DISABLE_FASTCLIP_CULL (1 << 5) |
| |
| #define MI_MODE 0x0209c |
| # define VS_TIMER_DISPATCH (1 << 6) |
| # define MI_FLUSH_ENABLE (1 << 12) |
| |
| #define GFX_MODE 0x02520 |
| #define GFX_MODE_GEN7 0x0229c |
| #define RING_MODE_GEN7(ring) ((ring)->mmio_base+0x29c) |
| #define GFX_RUN_LIST_ENABLE (1<<15) |
| #define GFX_TLB_INVALIDATE_ALWAYS (1<<13) |
| #define GFX_SURFACE_FAULT_ENABLE (1<<12) |
| #define GFX_REPLAY_MODE (1<<11) |
| #define GFX_PSMI_GRANULARITY (1<<10) |
| #define GFX_PPGTT_ENABLE (1<<9) |
| |
| #define VLV_DISPLAY_BASE 0x180000 |
| |
| #define SCPD0 0x0209c /* 915+ only */ |
| #define IER 0x020a0 |
| #define IIR 0x020a4 |
| #define IMR 0x020a8 |
| #define ISR 0x020ac |
| #define VLV_IIR_RW 0x182084 |
| #define VLV_IER 0x1820a0 |
| #define VLV_IIR 0x1820a4 |
| #define VLV_IMR 0x1820a8 |
| #define VLV_ISR 0x1820ac |
| #define I915_PIPE_CONTROL_NOTIFY_INTERRUPT (1<<18) |
| #define I915_DISPLAY_PORT_INTERRUPT (1<<17) |
| #define I915_RENDER_COMMAND_PARSER_ERROR_INTERRUPT (1<<15) |
| #define I915_GMCH_THERMAL_SENSOR_EVENT_INTERRUPT (1<<14) /* p-state */ |
| #define I915_HWB_OOM_INTERRUPT (1<<13) |
| #define I915_SYNC_STATUS_INTERRUPT (1<<12) |
| #define I915_DISPLAY_PLANE_A_FLIP_PENDING_INTERRUPT (1<<11) |
| #define I915_DISPLAY_PLANE_B_FLIP_PENDING_INTERRUPT (1<<10) |
| #define I915_OVERLAY_PLANE_FLIP_PENDING_INTERRUPT (1<<9) |
| #define I915_DISPLAY_PLANE_C_FLIP_PENDING_INTERRUPT (1<<8) |
| #define I915_DISPLAY_PIPE_A_VBLANK_INTERRUPT (1<<7) |
| #define I915_DISPLAY_PIPE_A_EVENT_INTERRUPT (1<<6) |
| #define I915_DISPLAY_PIPE_B_VBLANK_INTERRUPT (1<<5) |
| #define I915_DISPLAY_PIPE_B_EVENT_INTERRUPT (1<<4) |
| #define I915_DEBUG_INTERRUPT (1<<2) |
| #define I915_USER_INTERRUPT (1<<1) |
| #define I915_ASLE_INTERRUPT (1<<0) |
| #define I915_BSD_USER_INTERRUPT (1<<25) |
| #define EIR 0x020b0 |
| #define EMR 0x020b4 |
| #define ESR 0x020b8 |
| #define GM45_ERROR_PAGE_TABLE (1<<5) |
| #define GM45_ERROR_MEM_PRIV (1<<4) |
| #define I915_ERROR_PAGE_TABLE (1<<4) |
| #define GM45_ERROR_CP_PRIV (1<<3) |
| #define I915_ERROR_MEMORY_REFRESH (1<<1) |
| #define I915_ERROR_INSTRUCTION (1<<0) |
| #define INSTPM 0x020c0 |
| #define INSTPM_SELF_EN (1<<12) /* 915GM only */ |
| #define INSTPM_AGPBUSY_DIS (1<<11) /* gen3: when disabled, pending interrupts |
| will not assert AGPBUSY# and will only |
| be delivered when out of C3. */ |
| #define INSTPM_FORCE_ORDERING (1<<7) /* GEN6+ */ |
| #define ACTHD 0x020c8 |
| #define FW_BLC 0x020d8 |
| #define FW_BLC2 0x020dc |
| #define FW_BLC_SELF 0x020e0 /* 915+ only */ |
| #define FW_BLC_SELF_EN_MASK (1<<31) |
| #define FW_BLC_SELF_FIFO_MASK (1<<16) /* 945 only */ |
| #define FW_BLC_SELF_EN (1<<15) /* 945 only */ |
| #define MM_BURST_LENGTH 0x00700000 |
| #define MM_FIFO_WATERMARK 0x0001F000 |
| #define LM_BURST_LENGTH 0x00000700 |
| #define LM_FIFO_WATERMARK 0x0000001F |
| #define MI_ARB_STATE 0x020e4 /* 915+ only */ |
| |
| /* Make render/texture TLB fetches lower priorty than associated data |
| * fetches. This is not turned on by default |
| */ |
| #define MI_ARB_RENDER_TLB_LOW_PRIORITY (1 << 15) |
| |
| /* Isoch request wait on GTT enable (Display A/B/C streams). |
| * Make isoch requests stall on the TLB update. May cause |
| * display underruns (test mode only) |
| */ |
| #define MI_ARB_ISOCH_WAIT_GTT (1 << 14) |
| |
| /* Block grant count for isoch requests when block count is |
| * set to a finite value. |
| */ |
| #define MI_ARB_BLOCK_GRANT_MASK (3 << 12) |
| #define MI_ARB_BLOCK_GRANT_8 (0 << 12) /* for 3 display planes */ |
| #define MI_ARB_BLOCK_GRANT_4 (1 << 12) /* for 2 display planes */ |
| #define MI_ARB_BLOCK_GRANT_2 (2 << 12) /* for 1 display plane */ |
| #define MI_ARB_BLOCK_GRANT_0 (3 << 12) /* don't use */ |
| |
| /* Enable render writes to complete in C2/C3/C4 power states. |
| * If this isn't enabled, render writes are prevented in low |
| * power states. That seems bad to me. |
| */ |
| #define MI_ARB_C3_LP_WRITE_ENABLE (1 << 11) |
| |
| /* This acknowledges an async flip immediately instead |
| * of waiting for 2TLB fetches. |
| */ |
| #define MI_ARB_ASYNC_FLIP_ACK_IMMEDIATE (1 << 10) |
| |
| /* Enables non-sequential data reads through arbiter |
| */ |
| #define MI_ARB_DUAL_DATA_PHASE_DISABLE (1 << 9) |
| |
| /* Disable FSB snooping of cacheable write cycles from binner/render |
| * command stream |
| */ |
| #define MI_ARB_CACHE_SNOOP_DISABLE (1 << 8) |
| |
| /* Arbiter time slice for non-isoch streams */ |
| #define MI_ARB_TIME_SLICE_MASK (7 << 5) |
| #define MI_ARB_TIME_SLICE_1 (0 << 5) |
| #define MI_ARB_TIME_SLICE_2 (1 << 5) |
| #define MI_ARB_TIME_SLICE_4 (2 << 5) |
| #define MI_ARB_TIME_SLICE_6 (3 << 5) |
| #define MI_ARB_TIME_SLICE_8 (4 << 5) |
| #define MI_ARB_TIME_SLICE_10 (5 << 5) |
| #define MI_ARB_TIME_SLICE_14 (6 << 5) |
| #define MI_ARB_TIME_SLICE_16 (7 << 5) |
| |
| /* Low priority grace period page size */ |
| #define MI_ARB_LOW_PRIORITY_GRACE_4KB (0 << 4) /* default */ |
| #define MI_ARB_LOW_PRIORITY_GRACE_8KB (1 << 4) |
| |
| /* Disable display A/B trickle feed */ |
| #define MI_ARB_DISPLAY_TRICKLE_FEED_DISABLE (1 << 2) |
| |
| /* Set display plane priority */ |
| #define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */ |
| #define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */ |
| |
| #define CACHE_MODE_0 0x02120 /* 915+ only */ |
| #define CM0_IZ_OPT_DISABLE (1<<6) |
| #define CM0_ZR_OPT_DISABLE (1<<5) |
| #define CM0_STC_EVICT_DISABLE_LRA_SNB (1<<5) |
| #define CM0_DEPTH_EVICT_DISABLE (1<<4) |
| #define CM0_COLOR_EVICT_DISABLE (1<<3) |
| #define CM0_DEPTH_WRITE_DISABLE (1<<1) |
| #define CM0_RC_OP_FLUSH_DISABLE (1<<0) |
| #define BB_ADDR 0x02140 /* 8 bytes */ |
| #define GFX_FLSH_CNTL 0x02170 /* 915+ only */ |
| #define ECOSKPD 0x021d0 |
| #define ECO_GATING_CX_ONLY (1<<3) |
| #define ECO_FLIP_DONE (1<<0) |
| |
| #define CACHE_MODE_1 0x7004 /* IVB+ */ |
| #define PIXEL_SUBSPAN_COLLECT_OPT_DISABLE (1<<6) |
| |
| /* GEN6 interrupt control |
| * Note that the per-ring interrupt bits do alias with the global interrupt bits |
| * in GTIMR. */ |
| #define GEN6_RENDER_HWSTAM 0x2098 |
| #define GEN6_RENDER_IMR 0x20a8 |
| #define GEN6_RENDER_CONTEXT_SWITCH_INTERRUPT (1 << 8) |
| #define GEN6_RENDER_PPGTT_PAGE_FAULT (1 << 7) |
| #define GEN6_RENDER_TIMEOUT_COUNTER_EXPIRED (1 << 6) |
| #define GEN6_RENDER_L3_PARITY_ERROR (1 << 5) |
| #define GEN6_RENDER_PIPE_CONTROL_NOTIFY_INTERRUPT (1 << 4) |
| #define GEN6_RENDER_COMMAND_PARSER_MASTER_ERROR (1 << 3) |
| #define GEN6_RENDER_SYNC_STATUS (1 << 2) |
| #define GEN6_RENDER_DEBUG_INTERRUPT (1 << 1) |
| #define GEN6_RENDER_USER_INTERRUPT (1 << 0) |
| |
| #define GEN6_BLITTER_HWSTAM 0x22098 |
| #define GEN6_BLITTER_IMR 0x220a8 |
| #define GEN6_BLITTER_MI_FLUSH_DW_NOTIFY_INTERRUPT (1 << 26) |
| #define GEN6_BLITTER_COMMAND_PARSER_MASTER_ERROR (1 << 25) |
| #define GEN6_BLITTER_SYNC_STATUS (1 << 24) |
| #define GEN6_BLITTER_USER_INTERRUPT (1 << 22) |
| |
| #define GEN6_BLITTER_ECOSKPD 0x221d0 |
| #define GEN6_BLITTER_LOCK_SHIFT 16 |
| #define GEN6_BLITTER_FBC_NOTIFY (1<<3) |
| |
| #define GEN6_BSD_SLEEP_PSMI_CONTROL 0x12050 |
| #define GEN6_BSD_SLEEP_MSG_DISABLE (1 << 0) |
| #define GEN6_BSD_SLEEP_FLUSH_DISABLE (1 << 2) |
| #define GEN6_BSD_SLEEP_INDICATOR (1 << 3) |
| #define GEN6_BSD_GO_INDICATOR (1 << 4) |
| |
| #define GEN6_BSD_HWSTAM 0x12098 |
| #define GEN6_BSD_IMR 0x120a8 |
| #define GEN6_BSD_USER_INTERRUPT (1 << 12) |
| |
| #define GEN6_BSD_RNCID 0x12198 |
| |
| #define GEN7_FF_THREAD_MODE 0x20a0 |
| #define GEN7_FF_SCHED_MASK 0x0077070 |
| #define GEN7_FF_TS_SCHED_HS1 (0x5<<16) |
| #define GEN7_FF_TS_SCHED_HS0 (0x3<<16) |
| #define GEN7_FF_TS_SCHED_LOAD_BALANCE (0x1<<16) |
| #define GEN7_FF_TS_SCHED_HW (0x0<<16) /* Default */ |
| #define GEN7_FF_VS_SCHED_HS1 (0x5<<12) |
| #define GEN7_FF_VS_SCHED_HS0 (0x3<<12) |
| #define GEN7_FF_VS_SCHED_LOAD_BALANCE (0x1<<12) /* Default */ |
| #define GEN7_FF_VS_SCHED_HW (0x0<<12) |
| #define GEN7_FF_DS_SCHED_HS1 (0x5<<4) |
| #define GEN7_FF_DS_SCHED_HS0 (0x3<<4) |
| #define GEN7_FF_DS_SCHED_LOAD_BALANCE (0x1<<4) /* Default */ |
| #define GEN7_FF_DS_SCHED_HW (0x0<<4) |
| |
| /* |
| * Framebuffer compression (915+ only) |
| */ |
| |
| #define FBC_CFB_BASE 0x03200 /* 4k page aligned */ |
| #define FBC_LL_BASE 0x03204 /* 4k page aligned */ |
| #define FBC_CONTROL 0x03208 |
| #define FBC_CTL_EN (1<<31) |
| #define FBC_CTL_PERIODIC (1<<30) |
| #define FBC_CTL_INTERVAL_SHIFT (16) |
| #define FBC_CTL_UNCOMPRESSIBLE (1<<14) |
| #define FBC_CTL_C3_IDLE (1<<13) |
| #define FBC_CTL_STRIDE_SHIFT (5) |
| #define FBC_CTL_FENCENO (1<<0) |
| #define FBC_COMMAND 0x0320c |
| #define FBC_CMD_COMPRESS (1<<0) |
| #define FBC_STATUS 0x03210 |
| #define FBC_STAT_COMPRESSING (1<<31) |
| #define FBC_STAT_COMPRESSED (1<<30) |
| #define FBC_STAT_MODIFIED (1<<29) |
| #define FBC_STAT_CURRENT_LINE (1<<0) |
| #define FBC_CONTROL2 0x03214 |
| #define FBC_CTL_FENCE_DBL (0<<4) |
| #define FBC_CTL_IDLE_IMM (0<<2) |
| #define FBC_CTL_IDLE_FULL (1<<2) |
| #define FBC_CTL_IDLE_LINE (2<<2) |
| #define FBC_CTL_IDLE_DEBUG (3<<2) |
| #define FBC_CTL_CPU_FENCE (1<<1) |
| #define FBC_CTL_PLANEA (0<<0) |
| #define FBC_CTL_PLANEB (1<<0) |
| #define FBC_FENCE_OFF 0x0321b |
| #define FBC_TAG 0x03300 |
| |
| #define FBC_LL_SIZE (1536) |
| |
| /* Framebuffer compression for GM45+ */ |
| #define DPFC_CB_BASE 0x3200 |
| #define DPFC_CONTROL 0x3208 |
| #define DPFC_CTL_EN (1<<31) |
| #define DPFC_CTL_PLANEA (0<<30) |
| #define DPFC_CTL_PLANEB (1<<30) |
| #define DPFC_CTL_FENCE_EN (1<<29) |
| #define DPFC_CTL_PERSISTENT_MODE (1<<25) |
| #define DPFC_SR_EN (1<<10) |
| #define DPFC_CTL_LIMIT_1X (0<<6) |
| #define DPFC_CTL_LIMIT_2X (1<<6) |
| #define DPFC_CTL_LIMIT_4X (2<<6) |
| #define DPFC_RECOMP_CTL 0x320c |
| #define DPFC_RECOMP_STALL_EN (1<<27) |
| #define DPFC_RECOMP_STALL_WM_SHIFT (16) |
| #define DPFC_RECOMP_STALL_WM_MASK (0x07ff0000) |
| #define DPFC_RECOMP_TIMER_COUNT_SHIFT (0) |
| #define DPFC_RECOMP_TIMER_COUNT_MASK (0x0000003f) |
| #define DPFC_STATUS 0x3210 |
| #define DPFC_INVAL_SEG_SHIFT (16) |
| #define DPFC_INVAL_SEG_MASK (0x07ff0000) |
| #define DPFC_COMP_SEG_SHIFT (0) |
| #define DPFC_COMP_SEG_MASK (0x000003ff) |
| #define DPFC_STATUS2 0x3214 |
| #define DPFC_FENCE_YOFF 0x3218 |
| #define DPFC_CHICKEN 0x3224 |
| #define DPFC_HT_MODIFY (1<<31) |
| |
| /* Framebuffer compression for Ironlake */ |
| #define ILK_DPFC_CB_BASE 0x43200 |
| #define ILK_DPFC_CONTROL 0x43208 |
| /* The bit 28-8 is reserved */ |
| #define DPFC_RESERVED (0x1FFFFF00) |
| #define ILK_DPFC_RECOMP_CTL 0x4320c |
| #define ILK_DPFC_STATUS 0x43210 |
| #define ILK_DPFC_FENCE_YOFF 0x43218 |
| #define ILK_DPFC_CHICKEN 0x43224 |
| #define ILK_FBC_RT_BASE 0x2128 |
| #define ILK_FBC_RT_VALID (1<<0) |
| |
| #define ILK_DISPLAY_CHICKEN1 0x42000 |
| #define ILK_FBCQ_DIS (1<<22) |
| #define ILK_PABSTRETCH_DIS (1<<21) |
| |
| |
| /* |
| * Framebuffer compression for Sandybridge |
| * |
| * The following two registers are of type GTTMMADR |
| */ |
| #define SNB_DPFC_CTL_SA 0x100100 |
| #define SNB_CPU_FENCE_ENABLE (1<<29) |
| #define DPFC_CPU_FENCE_OFFSET 0x100104 |
| |
| |
| /* |
| * GPIO regs |
| */ |
| #define GPIOA 0x5010 |
| #define GPIOB 0x5014 |
| #define GPIOC 0x5018 |
| #define GPIOD 0x501c |
| #define GPIOE 0x5020 |
| #define GPIOF 0x5024 |
| #define GPIOG 0x5028 |
| #define GPIOH 0x502c |
| # define GPIO_CLOCK_DIR_MASK (1 << 0) |
| # define GPIO_CLOCK_DIR_IN (0 << 1) |
| # define GPIO_CLOCK_DIR_OUT (1 << 1) |
| # define GPIO_CLOCK_VAL_MASK (1 << 2) |
| # define GPIO_CLOCK_VAL_OUT (1 << 3) |
| # define GPIO_CLOCK_VAL_IN (1 << 4) |
| # define GPIO_CLOCK_PULLUP_DISABLE (1 << 5) |
| # define GPIO_DATA_DIR_MASK (1 << 8) |
| # define GPIO_DATA_DIR_IN (0 << 9) |
| # define GPIO_DATA_DIR_OUT (1 << 9) |
| # define GPIO_DATA_VAL_MASK (1 << 10) |
| # define GPIO_DATA_VAL_OUT (1 << 11) |
| # define GPIO_DATA_VAL_IN (1 << 12) |
| # define GPIO_DATA_PULLUP_DISABLE (1 << 13) |
| |
| #define GMBUS0 0x5100 /* clock/port select */ |
| #define GMBUS_RATE_100KHZ (0<<8) |
| #define GMBUS_RATE_50KHZ (1<<8) |
| #define GMBUS_RATE_400KHZ (2<<8) /* reserved on Pineview */ |
| #define GMBUS_RATE_1MHZ (3<<8) /* reserved on Pineview */ |
| #define GMBUS_HOLD_EXT (1<<7) /* 300ns hold time, rsvd on Pineview */ |
| #define GMBUS_PORT_DISABLED 0 |
| #define GMBUS_PORT_SSC 1 |
| #define GMBUS_PORT_VGADDC 2 |
| #define GMBUS_PORT_PANEL 3 |
| #define GMBUS_PORT_DPC 4 /* HDMIC */ |
| #define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */ |
| #define GMBUS_PORT_DPD 6 /* HDMID */ |
| #define GMBUS_PORT_RESERVED 7 /* 7 reserved */ |
| #define GMBUS_NUM_PORTS (GMBUS_PORT_DPD - GMBUS_PORT_SSC + 1) |
| #define GMBUS1 0x5104 /* command/status */ |
| #define GMBUS_SW_CLR_INT (1<<31) |
| #define GMBUS_SW_RDY (1<<30) |
| #define GMBUS_ENT (1<<29) /* enable timeout */ |
| #define GMBUS_CYCLE_NONE (0<<25) |
| #define GMBUS_CYCLE_WAIT (1<<25) |
| #define GMBUS_CYCLE_INDEX (2<<25) |
| #define GMBUS_CYCLE_STOP (4<<25) |
| #define GMBUS_BYTE_COUNT_SHIFT 16 |
| #define GMBUS_SLAVE_INDEX_SHIFT 8 |
| #define GMBUS_SLAVE_ADDR_SHIFT 1 |
| #define GMBUS_SLAVE_READ (1<<0) |
| #define GMBUS_SLAVE_WRITE (0<<0) |
| #define GMBUS2 0x5108 /* status */ |
| #define GMBUS_INUSE (1<<15) |
| #define GMBUS_HW_WAIT_PHASE (1<<14) |
| #define GMBUS_STALL_TIMEOUT (1<<13) |
| #define GMBUS_INT (1<<12) |
| #define GMBUS_HW_RDY (1<<11) |
| #define GMBUS_SATOER (1<<10) |
| #define GMBUS_ACTIVE (1<<9) |
| #define GMBUS3 0x510c /* data buffer bytes 3-0 */ |
| #define GMBUS4 0x5110 /* interrupt mask (Pineview+) */ |
| #define GMBUS_SLAVE_TIMEOUT_EN (1<<4) |
| #define GMBUS_NAK_EN (1<<3) |
| #define GMBUS_IDLE_EN (1<<2) |
| #define GMBUS_HW_WAIT_EN (1<<1) |
| #define GMBUS_HW_RDY_EN (1<<0) |
| #define GMBUS5 0x5120 /* byte index */ |
| #define GMBUS_2BYTE_INDEX_EN (1<<31) |
| |
| /* |
| * Clock control & power management |
| */ |
| |
| #define VGA0 0x6000 |
| #define VGA1 0x6004 |
| #define VGA_PD 0x6010 |
| #define VGA0_PD_P2_DIV_4 (1 << 7) |
| #define VGA0_PD_P1_DIV_2 (1 << 5) |
| #define VGA0_PD_P1_SHIFT 0 |
| #define VGA0_PD_P1_MASK (0x1f << 0) |
| #define VGA1_PD_P2_DIV_4 (1 << 15) |
| #define VGA1_PD_P1_DIV_2 (1 << 13) |
| #define VGA1_PD_P1_SHIFT 8 |
| #define VGA1_PD_P1_MASK (0x1f << 8) |
| #define _DPLL_A 0x06014 |
| #define _DPLL_B 0x06018 |
| #define DPLL(pipe) _PIPE(pipe, _DPLL_A, _DPLL_B) |
| #define DPLL_VCO_ENABLE (1 << 31) |
| #define DPLL_DVO_HIGH_SPEED (1 << 30) |
| #define DPLL_EXT_BUFFER_ENABLE_VLV (1 << 30) |
| #define DPLL_SYNCLOCK_ENABLE (1 << 29) |
| #define DPLL_REFA_CLK_ENABLE_VLV (1 << 29) |
| #define DPLL_VGA_MODE_DIS (1 << 28) |
| #define DPLLB_MODE_DAC_SERIAL (1 << 26) /* i915 */ |
| #define DPLLB_MODE_LVDS (2 << 26) /* i915 */ |
| #define DPLL_MODE_MASK (3 << 26) |
| #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_10 (0 << 24) /* i915 */ |
| #define DPLL_DAC_SERIAL_P2_CLOCK_DIV_5 (1 << 24) /* i915 */ |
| #define DPLLB_LVDS_P2_CLOCK_DIV_14 (0 << 24) /* i915 */ |
| #define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */ |
| #define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */ |
| #define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */ |
| #define DPLL_FPA01_P1_POST_DIV_MASK_PINEVIEW 0x00ff8000 /* Pineview */ |
| #define DPLL_LOCK_VLV (1<<15) |
| #define DPLL_INTEGRATED_CLOCK_VLV (1<<13) |
| |
| #define SRX_INDEX 0x3c4 |
| #define SRX_DATA 0x3c5 |
| #define SR01 1 |
| #define SR01_SCREEN_OFF (1<<5) |
| |
| #define PPCR 0x61204 |
| #define PPCR_ON (1<<0) |
| |
| #define DVOB 0x61140 |
| #define DVOB_ON (1<<31) |
| #define DVOC 0x61160 |
| #define DVOC_ON (1<<31) |
| #define LVDS 0x61180 |
| #define LVDS_ON (1<<31) |
| |
| /* Scratch pad debug 0 reg: |
| */ |
| #define DPLL_FPA01_P1_POST_DIV_MASK_I830 0x001f0000 |
| /* |
| * The i830 generation, in LVDS mode, defines P1 as the bit number set within |
| * this field (only one bit may be set). |
| */ |
| #define DPLL_FPA01_P1_POST_DIV_MASK_I830_LVDS 0x003f0000 |
| #define DPLL_FPA01_P1_POST_DIV_SHIFT 16 |
| #define DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW 15 |
| /* i830, required in DVO non-gang */ |
| #define PLL_P2_DIVIDE_BY_4 (1 << 23) |
| #define PLL_P1_DIVIDE_BY_TWO (1 << 21) /* i830 */ |
| #define PLL_REF_INPUT_DREFCLK (0 << 13) |
| #define PLL_REF_INPUT_TVCLKINA (1 << 13) /* i830 */ |
| #define PLL_REF_INPUT_TVCLKINBC (2 << 13) /* SDVO TVCLKIN */ |
| #define PLLB_REF_INPUT_SPREADSPECTRUMIN (3 << 13) |
| #define PLL_REF_INPUT_MASK (3 << 13) |
| #define PLL_LOAD_PULSE_PHASE_SHIFT 9 |
| /* Ironlake */ |
| # define PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT 9 |
| # define PLL_REF_SDVO_HDMI_MULTIPLIER_MASK (7 << 9) |
| # define PLL_REF_SDVO_HDMI_MULTIPLIER(x) (((x)-1) << 9) |
| # define DPLL_FPA1_P1_POST_DIV_SHIFT 0 |
| # define DPLL_FPA1_P1_POST_DIV_MASK 0xff |
| |
| /* |
| * Parallel to Serial Load Pulse phase selection. |
| * Selects the phase for the 10X DPLL clock for the PCIe |
| * digital display port. The range is 4 to 13; 10 or more |
| * is just a flip delay. The default is 6 |
| */ |
| #define PLL_LOAD_PULSE_PHASE_MASK (0xf << PLL_LOAD_PULSE_PHASE_SHIFT) |
| #define DISPLAY_RATE_SELECT_FPA1 (1 << 8) |
| /* |
| * SDVO multiplier for 945G/GM. Not used on 965. |
| */ |
| #define SDVO_MULTIPLIER_MASK 0x000000ff |
| #define SDVO_MULTIPLIER_SHIFT_HIRES 4 |
| #define SDVO_MULTIPLIER_SHIFT_VGA 0 |
| #define _DPLL_A_MD 0x0601c /* 965+ only */ |
| /* |
| * UDI pixel divider, controlling how many pixels are stuffed into a packet. |
| * |
| * Value is pixels minus 1. Must be set to 1 pixel for SDVO. |
| */ |
| #define DPLL_MD_UDI_DIVIDER_MASK 0x3f000000 |
| #define DPLL_MD_UDI_DIVIDER_SHIFT 24 |
| /* UDI pixel divider for VGA, same as DPLL_MD_UDI_DIVIDER_MASK. */ |
| #define DPLL_MD_VGA_UDI_DIVIDER_MASK 0x003f0000 |
| #define DPLL_MD_VGA_UDI_DIVIDER_SHIFT 16 |
| /* |
| * SDVO/UDI pixel multiplier. |
| * |
| * SDVO requires that the bus clock rate be between 1 and 2 Ghz, and the bus |
| * clock rate is 10 times the DPLL clock. At low resolution/refresh rate |
| * modes, the bus rate would be below the limits, so SDVO allows for stuffing |
| * dummy bytes in the datastream at an increased clock rate, with both sides of |
| * the link knowing how many bytes are fill. |
| * |
| * So, for a mode with a dotclock of 65Mhz, we would want to double the clock |
| * rate to 130Mhz to get a bus rate of 1.30Ghz. The DPLL clock rate would be |
| * set to 130Mhz, and the SDVO multiplier set to 2x in this register and |
| * through an SDVO command. |
| * |
| * This register field has values of multiplication factor minus 1, with |
| * a maximum multiplier of 5 for SDVO. |
| */ |
| #define DPLL_MD_UDI_MULTIPLIER_MASK 0x00003f00 |
| #define DPLL_MD_UDI_MULTIPLIER_SHIFT 8 |
| /* |
| * SDVO/UDI pixel multiplier for VGA, same as DPLL_MD_UDI_MULTIPLIER_MASK. |
| * This best be set to the default value (3) or the CRT won't work. No, |
| * I don't entirely understand what this does... |
| */ |
| #define DPLL_MD_VGA_UDI_MULTIPLIER_MASK 0x0000003f |
| #define DPLL_MD_VGA_UDI_MULTIPLIER_SHIFT 0 |
| #define _DPLL_B_MD 0x06020 /* 965+ only */ |
| #define DPLL_MD(pipe) _PIPE(pipe, _DPLL_A_MD, _DPLL_B_MD) |
| |
| #define _FPA0 0x06040 |
| #define _FPA1 0x06044 |
| #define _FPB0 0x06048 |
| #define _FPB1 0x0604c |
| #define FP0(pipe) _PIPE(pipe, _FPA0, _FPB0) |
| #define FP1(pipe) _PIPE(pipe, _FPA1, _FPB1) |
| #define FP_N_DIV_MASK 0x003f0000 |
| #define FP_N_PINEVIEW_DIV_MASK 0x00ff0000 |
| #define FP_N_DIV_SHIFT 16 |
| #define FP_M1_DIV_MASK 0x00003f00 |
| #define FP_M1_DIV_SHIFT 8 |
| #define FP_M2_DIV_MASK 0x0000003f |
| #define FP_M2_PINEVIEW_DIV_MASK 0x000000ff |
| #define FP_M2_DIV_SHIFT 0 |
| #define DPLL_TEST 0x606c |
| #define DPLLB_TEST_SDVO_DIV_1 (0 << 22) |
| #define DPLLB_TEST_SDVO_DIV_2 (1 << 22) |
| #define DPLLB_TEST_SDVO_DIV_4 (2 << 22) |
| #define DPLLB_TEST_SDVO_DIV_MASK (3 << 22) |
| #define DPLLB_TEST_N_BYPASS (1 << 19) |
| #define DPLLB_TEST_M_BYPASS (1 << 18) |
| #define DPLLB_INPUT_BUFFER_ENABLE (1 << 16) |
| #define DPLLA_TEST_N_BYPASS (1 << 3) |
| #define DPLLA_TEST_M_BYPASS (1 << 2) |
| #define DPLLA_INPUT_BUFFER_ENABLE (1 << 0) |
| #define D_STATE 0x6104 |
| #define DSTATE_GFX_RESET_I830 (1<<6) |
| #define DSTATE_PLL_D3_OFF (1<<3) |
| #define DSTATE_GFX_CLOCK_GATING (1<<1) |
| #define DSTATE_DOT_CLOCK_GATING (1<<0) |
| #define DSPCLK_GATE_D 0x6200 |
| # define DPUNIT_B_CLOCK_GATE_DISABLE (1 << 30) /* 965 */ |
| # define VSUNIT_CLOCK_GATE_DISABLE (1 << 29) /* 965 */ |
| # define VRHUNIT_CLOCK_GATE_DISABLE (1 << 28) /* 965 */ |
| # define VRDUNIT_CLOCK_GATE_DISABLE (1 << 27) /* 965 */ |
| # define AUDUNIT_CLOCK_GATE_DISABLE (1 << 26) /* 965 */ |
| # define DPUNIT_A_CLOCK_GATE_DISABLE (1 << 25) /* 965 */ |
| # define DPCUNIT_CLOCK_GATE_DISABLE (1 << 24) /* 965 */ |
| # define TVRUNIT_CLOCK_GATE_DISABLE (1 << 23) /* 915-945 */ |
| # define TVCUNIT_CLOCK_GATE_DISABLE (1 << 22) /* 915-945 */ |
| # define TVFUNIT_CLOCK_GATE_DISABLE (1 << 21) /* 915-945 */ |
| # define TVEUNIT_CLOCK_GATE_DISABLE (1 << 20) /* 915-945 */ |
| # define DVSUNIT_CLOCK_GATE_DISABLE (1 << 19) /* 915-945 */ |
| # define DSSUNIT_CLOCK_GATE_DISABLE (1 << 18) /* 915-945 */ |
| # define DDBUNIT_CLOCK_GATE_DISABLE (1 << 17) /* 915-945 */ |
| # define DPRUNIT_CLOCK_GATE_DISABLE (1 << 16) /* 915-945 */ |
| # define DPFUNIT_CLOCK_GATE_DISABLE (1 << 15) /* 915-945 */ |
| # define DPBMUNIT_CLOCK_GATE_DISABLE (1 << 14) /* 915-945 */ |
| # define DPLSUNIT_CLOCK_GATE_DISABLE (1 << 13) /* 915-945 */ |
| # define DPLUNIT_CLOCK_GATE_DISABLE (1 << 12) /* 915-945 */ |
| # define DPOUNIT_CLOCK_GATE_DISABLE (1 << 11) |
| # define DPBUNIT_CLOCK_GATE_DISABLE (1 << 10) |
| # define DCUNIT_CLOCK_GATE_DISABLE (1 << 9) |
| # define DPUNIT_CLOCK_GATE_DISABLE (1 << 8) |
| # define VRUNIT_CLOCK_GATE_DISABLE (1 << 7) /* 915+: reserved */ |
| # define OVHUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 830-865 */ |
| # define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 915-945 */ |
| # define OVFUNIT_CLOCK_GATE_DISABLE (1 << 5) |
| # define OVBUNIT_CLOCK_GATE_DISABLE (1 << 4) |
| /** |
| * This bit must be set on the 830 to prevent hangs when turning off the |
| * overlay scaler. |
| */ |
| # define OVRUNIT_CLOCK_GATE_DISABLE (1 << 3) |
| # define OVCUNIT_CLOCK_GATE_DISABLE (1 << 2) |
| # define OVUUNIT_CLOCK_GATE_DISABLE (1 << 1) |
| # define ZVUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 830 */ |
| # define OVLUNIT_CLOCK_GATE_DISABLE (1 << 0) /* 845,865 */ |
| |
| #define RENCLK_GATE_D1 0x6204 |
| # define BLITTER_CLOCK_GATE_DISABLE (1 << 13) /* 945GM only */ |
| # define MPEG_CLOCK_GATE_DISABLE (1 << 12) /* 945GM only */ |
| # define PC_FE_CLOCK_GATE_DISABLE (1 << 11) |
| # define PC_BE_CLOCK_GATE_DISABLE (1 << 10) |
| # define WINDOWER_CLOCK_GATE_DISABLE (1 << 9) |
| # define INTERPOLATOR_CLOCK_GATE_DISABLE (1 << 8) |
| # define COLOR_CALCULATOR_CLOCK_GATE_DISABLE (1 << 7) |
| # define MOTION_COMP_CLOCK_GATE_DISABLE (1 << 6) |
| # define MAG_CLOCK_GATE_DISABLE (1 << 5) |
| /** This bit must be unset on 855,865 */ |
| # define MECI_CLOCK_GATE_DISABLE (1 << 4) |
| # define DCMP_CLOCK_GATE_DISABLE (1 << 3) |
| # define MEC_CLOCK_GATE_DISABLE (1 << 2) |
| # define MECO_CLOCK_GATE_DISABLE (1 << 1) |
| /** This bit must be set on 855,865. */ |
| # define SV_CLOCK_GATE_DISABLE (1 << 0) |
| # define I915_MPEG_CLOCK_GATE_DISABLE (1 << 16) |
| # define I915_VLD_IP_PR_CLOCK_GATE_DISABLE (1 << 15) |
| # define I915_MOTION_COMP_CLOCK_GATE_DISABLE (1 << 14) |
| # define I915_BD_BF_CLOCK_GATE_DISABLE (1 << 13) |
| # define I915_SF_SE_CLOCK_GATE_DISABLE (1 << 12) |
| # define I915_WM_CLOCK_GATE_DISABLE (1 << 11) |
| # define I915_IZ_CLOCK_GATE_DISABLE (1 << 10) |
| # define I915_PI_CLOCK_GATE_DISABLE (1 << 9) |
| # define I915_DI_CLOCK_GATE_DISABLE (1 << 8) |
| # define I915_SH_SV_CLOCK_GATE_DISABLE (1 << 7) |
| # define I915_PL_DG_QC_FT_CLOCK_GATE_DISABLE (1 << 6) |
| # define I915_SC_CLOCK_GATE_DISABLE (1 << 5) |
| # define I915_FL_CLOCK_GATE_DISABLE (1 << 4) |
| # define I915_DM_CLOCK_GATE_DISABLE (1 << 3) |
| # define I915_PS_CLOCK_GATE_DISABLE (1 << 2) |
| # define I915_CC_CLOCK_GATE_DISABLE (1 << 1) |
| # define I915_BY_CLOCK_GATE_DISABLE (1 << 0) |
| |
| # define I965_RCZ_CLOCK_GATE_DISABLE (1 << 30) |
| /** This bit must always be set on 965G/965GM */ |
| # define I965_RCC_CLOCK_GATE_DISABLE (1 << 29) |
| # define I965_RCPB_CLOCK_GATE_DISABLE (1 << 28) |
| # define I965_DAP_CLOCK_GATE_DISABLE (1 << 27) |
| # define I965_ROC_CLOCK_GATE_DISABLE (1 << 26) |
| # define I965_GW_CLOCK_GATE_DISABLE (1 << 25) |
| # define I965_TD_CLOCK_GATE_DISABLE (1 << 24) |
| /** This bit must always be set on 965G */ |
| # define I965_ISC_CLOCK_GATE_DISABLE (1 << 23) |
| # define I965_IC_CLOCK_GATE_DISABLE (1 << 22) |
| # define I965_EU_CLOCK_GATE_DISABLE (1 << 21) |
| # define I965_IF_CLOCK_GATE_DISABLE (1 << 20) |
| # define I965_TC_CLOCK_GATE_DISABLE (1 << 19) |
| # define I965_SO_CLOCK_GATE_DISABLE (1 << 17) |
| # define I965_FBC_CLOCK_GATE_DISABLE (1 << 16) |
| # define I965_MARI_CLOCK_GATE_DISABLE (1 << 15) |
| # define I965_MASF_CLOCK_GATE_DISABLE (1 << 14) |
| # define I965_MAWB_CLOCK_GATE_DISABLE (1 << 13) |
| # define I965_EM_CLOCK_GATE_DISABLE (1 << 12) |
| # define I965_UC_CLOCK_GATE_DISABLE (1 << 11) |
| # define I965_SI_CLOCK_GATE_DISABLE (1 << 6) |
| # define I965_MT_CLOCK_GATE_DISABLE (1 << 5) |
| # define I965_PL_CLOCK_GATE_DISABLE (1 << 4) |
| # define I965_DG_CLOCK_GATE_DISABLE (1 << 3) |
| # define I965_QC_CLOCK_GATE_DISABLE (1 << 2) |
| # define I965_FT_CLOCK_GATE_DISABLE (1 << 1) |
| # define I965_DM_CLOCK_GATE_DISABLE (1 << 0) |
| |
| #define RENCLK_GATE_D2 0x6208 |
| #define VF_UNIT_CLOCK_GATE_DISABLE (1 << 9) |
| #define GS_UNIT_CLOCK_GATE_DISABLE (1 << 7) |
| #define CL_UNIT_CLOCK_GATE_DISABLE (1 << 6) |
| #define RAMCLK_GATE_D 0x6210 /* CRL only */ |
| #define DEUC 0x6214 /* CRL only */ |
| |
| #define FW_BLC_SELF_VLV 0x6500 |
| #define FW_CSPWRDWNEN (1<<15) |
| |
| /* |
| * Palette regs |
| */ |
| |
| #define _PALETTE_A 0x0a000 |
| #define _PALETTE_B 0x0a800 |
| #define PALETTE(pipe) _PIPE(pipe, _PALETTE_A, _PALETTE_B) |
| |
| /* MCH MMIO space */ |
| |
| /* |
| * MCHBAR mirror. |
| * |
| * This mirrors the MCHBAR MMIO space whose location is determined by |
| * device 0 function 0's pci config register 0x44 or 0x48 and matches it in |
| * every way. It is not accessible from the CP register read instructions. |
| * |
| */ |
| #define MCHBAR_MIRROR_BASE 0x10000 |
| |
| #define MCHBAR_MIRROR_BASE_SNB 0x140000 |
| |
| /** 915-945 and GM965 MCH register controlling DRAM channel access */ |
| #define DCC 0x10200 |
| #define DCC_ADDRESSING_MODE_SINGLE_CHANNEL (0 << 0) |
| #define DCC_ADDRESSING_MODE_DUAL_CHANNEL_ASYMMETRIC (1 << 0) |
| #define DCC_ADDRESSING_MODE_DUAL_CHANNEL_INTERLEAVED (2 << 0) |
| #define DCC_ADDRESSING_MODE_MASK (3 << 0) |
| #define DCC_CHANNEL_XOR_DISABLE (1 << 10) |
| #define DCC_CHANNEL_XOR_BIT_17 (1 << 9) |
| |
| /** Pineview MCH register contains DDR3 setting */ |
| #define CSHRDDR3CTL 0x101a8 |
| #define CSHRDDR3CTL_DDR3 (1 << 2) |
| |
| /** 965 MCH register controlling DRAM channel configuration */ |
| #define C0DRB3 0x10206 |
| #define C1DRB3 0x10606 |
| |
| /** snb MCH registers for reading the DRAM channel configuration */ |
| #define MAD_DIMM_C0 (MCHBAR_MIRROR_BASE_SNB + 0x5004) |
| #define MAD_DIMM_C1 (MCHBAR_MIRROR_BASE_SNB + 0x5008) |
| #define MAD_DIMM_C2 (MCHBAR_MIRROR_BASE_SNB + 0x500C) |
| #define MAD_DIMM_ECC_MASK (0x3 << 24) |
| #define MAD_DIMM_ECC_OFF (0x0 << 24) |
| #define MAD_DIMM_ECC_IO_ON_LOGIC_OFF (0x1 << 24) |
| #define MAD_DIMM_ECC_IO_OFF_LOGIC_ON (0x2 << 24) |
| #define MAD_DIMM_ECC_ON (0x3 << 24) |
| #define MAD_DIMM_ENH_INTERLEAVE (0x1 << 22) |
| #define MAD_DIMM_RANK_INTERLEAVE (0x1 << 21) |
| #define MAD_DIMM_B_WIDTH_X16 (0x1 << 20) /* X8 chips if unset */ |
| #define MAD_DIMM_A_WIDTH_X16 (0x1 << 19) /* X8 chips if unset */ |
| #define MAD_DIMM_B_DUAL_RANK (0x1 << 18) |
| #define MAD_DIMM_A_DUAL_RANK (0x1 << 17) |
| #define MAD_DIMM_A_SELECT (0x1 << 16) |
| /* DIMM sizes are in multiples of 256mb. */ |
| #define MAD_DIMM_B_SIZE_SHIFT 8 |
| #define MAD_DIMM_B_SIZE_MASK (0xff << MAD_DIMM_B_SIZE_SHIFT) |
| #define MAD_DIMM_A_SIZE_SHIFT 0 |
| #define MAD_DIMM_A_SIZE_MASK (0xff << MAD_DIMM_A_SIZE_SHIFT) |
| |
| |
| /* Clocking configuration register */ |
| #define CLKCFG 0x10c00 |
| #define CLKCFG_FSB_400 (5 << 0) /* hrawclk 100 */ |
| #define CLKCFG_FSB_533 (1 << 0) /* hrawclk 133 */ |
| #define CLKCFG_FSB_667 (3 << 0) /* hrawclk 166 */ |
| #define CLKCFG_FSB_800 (2 << 0) /* hrawclk 200 */ |
| #define CLKCFG_FSB_1067 (6 << 0) /* hrawclk 266 */ |
| #define CLKCFG_FSB_1333 (7 << 0) /* hrawclk 333 */ |
| /* Note, below two are guess */ |
| #define CLKCFG_FSB_1600 (4 << 0) /* hrawclk 400 */ |
| #define CLKCFG_FSB_1600_ALT (0 << 0) /* hrawclk 400 */ |
| #define CLKCFG_FSB_MASK (7 << 0) |
| #define CLKCFG_MEM_533 (1 << 4) |
| #define CLKCFG_MEM_667 (2 << 4) |
| #define CLKCFG_MEM_800 (3 << 4) |
| #define CLKCFG_MEM_MASK (7 << 4) |
| |
| #define TSC1 0x11001 |
| #define TSE (1<<0) |
| #define TR1 0x11006 |
| #define TSFS 0x11020 |
| #define TSFS_SLOPE_MASK 0x0000ff00 |
| #define TSFS_SLOPE_SHIFT 8 |
| #define TSFS_INTR_MASK 0x000000ff |
| |
| #define CRSTANDVID 0x11100 |
| #define PXVFREQ_BASE 0x11110 /* P[0-15]VIDFREQ (0x1114c) (Ironlake) */ |
| #define PXVFREQ_PX_MASK 0x7f000000 |
| #define PXVFREQ_PX_SHIFT 24 |
| #define VIDFREQ_BASE 0x11110 |
| #define VIDFREQ1 0x11110 /* VIDFREQ1-4 (0x1111c) (Cantiga) */ |
| #define VIDFREQ2 0x11114 |
| #define VIDFREQ3 0x11118 |
| #define VIDFREQ4 0x1111c |
| #define VIDFREQ_P0_MASK 0x1f000000 |
| #define VIDFREQ_P0_SHIFT 24 |
| #define VIDFREQ_P0_CSCLK_MASK 0x00f00000 |
| #define VIDFREQ_P0_CSCLK_SHIFT 20 |
| #define VIDFREQ_P0_CRCLK_MASK 0x000f0000 |
| #define VIDFREQ_P0_CRCLK_SHIFT 16 |
| #define VIDFREQ_P1_MASK 0x00001f00 |
| #define VIDFREQ_P1_SHIFT 8 |
| #define VIDFREQ_P1_CSCLK_MASK 0x000000f0 |
| #define VIDFREQ_P1_CSCLK_SHIFT 4 |
| #define VIDFREQ_P1_CRCLK_MASK 0x0000000f |
| #define INTTOEXT_BASE_ILK 0x11300 |
| #define INTTOEXT_BASE 0x11120 /* INTTOEXT1-8 (0x1113c) */ |
| #define INTTOEXT_MAP3_SHIFT 24 |
| #define INTTOEXT_MAP3_MASK (0x1f << INTTOEXT_MAP3_SHIFT) |
| #define INTTOEXT_MAP2_SHIFT 16 |
| #define INTTOEXT_MAP2_MASK (0x1f << INTTOEXT_MAP2_SHIFT) |
| #define INTTOEXT_MAP1_SHIFT 8 |
| #define INTTOEXT_MAP1_MASK (0x1f << INTTOEXT_MAP1_SHIFT) |
| #define INTTOEXT_MAP0_SHIFT 0 |
| #define INTTOEXT_MAP0_MASK (0x1f << INTTOEXT_MAP0_SHIFT) |
| #define MEMSWCTL 0x11170 /* Ironlake only */ |
| #define MEMCTL_CMD_MASK 0xe000 |
| #define MEMCTL_CMD_SHIFT 13 |
| #define MEMCTL_CMD_RCLK_OFF 0 |
| #define MEMCTL_CMD_RCLK_ON 1 |
| #define MEMCTL_CMD_CHFREQ 2 |
| #define MEMCTL_CMD_CHVID 3 |
| #define MEMCTL_CMD_VMMOFF 4 |
| #define MEMCTL_CMD_VMMON 5 |
| #define MEMCTL_CMD_STS (1<<12) /* write 1 triggers command, clears |
| when command complete */ |
| #define MEMCTL_FREQ_MASK 0x0f00 /* jitter, from 0-15 */ |
| #define MEMCTL_FREQ_SHIFT 8 |
| #define MEMCTL_SFCAVM (1<<7) |
| #define MEMCTL_TGT_VID_MASK 0x007f |
| #define MEMIHYST 0x1117c |
| #define MEMINTREN 0x11180 /* 16 bits */ |
| #define MEMINT_RSEXIT_EN (1<<8) |
| #define MEMINT_CX_SUPR_EN (1<<7) |
| #define MEMINT_CONT_BUSY_EN (1<<6) |
| #define MEMINT_AVG_BUSY_EN (1<<5) |
| #define MEMINT_EVAL_CHG_EN (1<<4) |
| #define MEMINT_MON_IDLE_EN (1<<3) |
| #define MEMINT_UP_EVAL_EN (1<<2) |
| #define MEMINT_DOWN_EVAL_EN (1<<1) |
| #define MEMINT_SW_CMD_EN (1<<0) |
| #define MEMINTRSTR 0x11182 /* 16 bits */ |
| #define MEM_RSEXIT_MASK 0xc000 |
| #define MEM_RSEXIT_SHIFT 14 |
| #define MEM_CONT_BUSY_MASK 0x3000 |
| #define MEM_CONT_BUSY_SHIFT 12 |
| #define MEM_AVG_BUSY_MASK 0x0c00 |
| #define MEM_AVG_BUSY_SHIFT 10 |
| #define MEM_EVAL_CHG_MASK 0x0300 |
| #define MEM_EVAL_BUSY_SHIFT 8 |
| #define MEM_MON_IDLE_MASK 0x00c0 |
| #define MEM_MON_IDLE_SHIFT 6 |
| #define MEM_UP_EVAL_MASK 0x0030 |
| #define MEM_UP_EVAL_SHIFT 4 |
| #define MEM_DOWN_EVAL_MASK 0x000c |
| #define MEM_DOWN_EVAL_SHIFT 2 |
| #define MEM_SW_CMD_MASK 0x0003 |
| #define MEM_INT_STEER_GFX 0 |
| #define MEM_INT_STEER_CMR 1 |
| #define MEM_INT_STEER_SMI 2 |
| #define MEM_INT_STEER_SCI 3 |
| #define MEMINTRSTS 0x11184 |
| #define MEMINT_RSEXIT (1<<7) |
| #define MEMINT_CONT_BUSY (1<<6) |
| #define MEMINT_AVG_BUSY (1<<5) |
| #define MEMINT_EVAL_CHG (1<<4) |
| #define MEMINT_MON_IDLE (1<<3) |
| #define MEMINT_UP_EVAL (1<<2) |
| #define MEMINT_DOWN_EVAL (1<<1) |
| #define MEMINT_SW_CMD (1<<0) |
| #define MEMMODECTL 0x11190 |
| #define MEMMODE_BOOST_EN (1<<31) |
| #define MEMMODE_BOOST_FREQ_MASK 0x0f000000 /* jitter for boost, 0-15 */ |
| #define MEMMODE_BOOST_FREQ_SHIFT 24 |
| #define MEMMODE_IDLE_MODE_MASK 0x00030000 |
| #define MEMMODE_IDLE_MODE_SHIFT 16 |
| #define MEMMODE_IDLE_MODE_EVAL 0 |
| #define MEMMODE_IDLE_MODE_CONT 1 |
| #define MEMMODE_HWIDLE_EN (1<<15) |
| #define MEMMODE_SWMODE_EN (1<<14) |
| #define MEMMODE_RCLK_GATE (1<<13) |
| #define MEMMODE_HW_UPDATE (1<<12) |
| #define MEMMODE_FSTART_MASK 0x00000f00 /* starting jitter, 0-15 */ |
| #define MEMMODE_FSTART_SHIFT 8 |
| #define MEMMODE_FMAX_MASK 0x000000f0 /* max jitter, 0-15 */ |
| #define MEMMODE_FMAX_SHIFT 4 |
| #define MEMMODE_FMIN_MASK 0x0000000f /* min jitter, 0-15 */ |
| #define RCBMAXAVG 0x1119c |
| #define MEMSWCTL2 0x1119e /* Cantiga only */ |
| #define SWMEMCMD_RENDER_OFF (0 << 13) |
| #define SWMEMCMD_RENDER_ON (1 << 13) |
| #define SWMEMCMD_SWFREQ (2 << 13) |
| #define SWMEMCMD_TARVID (3 << 13) |
| #define SWMEMCMD_VRM_OFF (4 << 13) |
| #define SWMEMCMD_VRM_ON (5 << 13) |
| #define CMDSTS (1<<12) |
| #define SFCAVM (1<<11) |
| #define SWFREQ_MASK 0x0380 /* P0-7 */ |
| #define SWFREQ_SHIFT 7 |
| #define TARVID_MASK 0x001f |
| #define MEMSTAT_CTG 0x111a0 |
| #define RCBMINAVG 0x111a0 |
| #define RCUPEI 0x111b0 |
| #define RCDNEI 0x111b4 |
| #define RSTDBYCTL 0x111b8 |
| #define RS1EN (1<<31) |
| #define RS2EN (1<<30) |
| #define RS3EN (1<<29) |
| #define D3RS3EN (1<<28) /* Display D3 imlies RS3 */ |
| #define SWPROMORSX (1<<27) /* RSx promotion timers ignored */ |
| #define RCWAKERW (1<<26) /* Resetwarn from PCH causes wakeup */ |
| #define DPRSLPVREN (1<<25) /* Fast voltage ramp enable */ |
| #define GFXTGHYST (1<<24) /* Hysteresis to allow trunk gating */ |
| #define RCX_SW_EXIT (1<<23) /* Leave RSx and prevent re-entry */ |
| #define RSX_STATUS_MASK (7<<20) |
| #define RSX_STATUS_ON (0<<20) |
| #define RSX_STATUS_RC1 (1<<20) |
| #define RSX_STATUS_RC1E (2<<20) |
| #define RSX_STATUS_RS1 (3<<20) |
| #define RSX_STATUS_RS2 (4<<20) /* aka rc6 */ |
| #define RSX_STATUS_RSVD (5<<20) /* deep rc6 unsupported on ilk */ |
| #define RSX_STATUS_RS3 (6<<20) /* rs3 unsupported on ilk */ |
| #define RSX_STATUS_RSVD2 (7<<20) |
| #define UWRCRSXE (1<<19) /* wake counter limit prevents rsx */ |
| #define RSCRP (1<<18) /* rs requests control on rs1/2 reqs */ |
| #define JRSC (1<<17) /* rsx coupled to cpu c-state */ |
| #define RS2INC0 (1<<16) /* allow rs2 in cpu c0 */ |
| #define RS1CONTSAV_MASK (3<<14) |
| #define RS1CONTSAV_NO_RS1 (0<<14) /* rs1 doesn't save/restore context */ |
| #define RS1CONTSAV_RSVD (1<<14) |
| #define RS1CONTSAV_SAVE_RS1 (2<<14) /* rs1 saves context */ |
| #define RS1CONTSAV_FULL_RS1 (3<<14) /* rs1 saves and restores context */ |
| #define NORMSLEXLAT_MASK (3<<12) |
| #define SLOW_RS123 (0<<12) |
| #define SLOW_RS23 (1<<12) |
| #define SLOW_RS3 (2<<12) |
| #define NORMAL_RS123 (3<<12) |
| #define RCMODE_TIMEOUT (1<<11) /* 0 is eval interval method */ |
| #define IMPROMOEN (1<<10) /* promo is immediate or delayed until next idle interval (only for timeout method above) */ |
| #define RCENTSYNC (1<<9) /* rs coupled to cpu c-state (3/6/7) */ |
| #define STATELOCK (1<<7) /* locked to rs_cstate if 0 */ |
| #define RS_CSTATE_MASK (3<<4) |
| #define RS_CSTATE_C367_RS1 (0<<4) |
| #define RS_CSTATE_C36_RS1_C7_RS2 (1<<4) |
| #define RS_CSTATE_RSVD (2<<4) |
| #define RS_CSTATE_C367_RS2 (3<<4) |
| #define REDSAVES (1<<3) /* no context save if was idle during rs0 */ |
| #define REDRESTORES (1<<2) /* no restore if was idle during rs0 */ |
| #define VIDCTL 0x111c0 |
| #define VIDSTS 0x111c8 |
| #define VIDSTART 0x111cc /* 8 bits */ |
| #define MEMSTAT_ILK 0x111f8 |
| #define MEMSTAT_VID_MASK 0x7f00 |
| #define MEMSTAT_VID_SHIFT 8 |
| #define MEMSTAT_PSTATE_MASK 0x00f8 |
| #define MEMSTAT_PSTATE_SHIFT 3 |
| #define MEMSTAT_MON_ACTV (1<<2) |
| #define MEMSTAT_SRC_CTL_MASK 0x0003 |
| #define MEMSTAT_SRC_CTL_CORE 0 |
| #define MEMSTAT_SRC_CTL_TRB 1 |
| #define MEMSTAT_SRC_CTL_THM 2 |
| #define MEMSTAT_SRC_CTL_STDBY 3 |
| #define RCPREVBSYTUPAVG 0x113b8 |
| #define RCPREVBSYTDNAVG 0x113bc |
| #define PMMISC 0x11214 |
| #define MCPPCE_EN (1<<0) /* enable PM_MSG from PCH->MPC */ |
| #define SDEW 0x1124c |
| #define CSIEW0 0x11250 |
| #define CSIEW1 0x11254 |
| #define CSIEW2 0x11258 |
| #define PEW 0x1125c |
| #define DEW 0x11270 |
| #define MCHAFE 0x112c0 |
| #define CSIEC 0x112e0 |
| #define DMIEC 0x112e4 |
| #define DDREC 0x112e8 |
| #define PEG0EC 0x112ec |
| #define PEG1EC 0x112f0 |
| #define GFXEC 0x112f4 |
| #define RPPREVBSYTUPAVG 0x113b8 |
| #define RPPREVBSYTDNAVG 0x113bc |
| #define ECR 0x11600 |
| #define ECR_GPFE (1<<31) |
| #define ECR_IMONE (1<<30) |
| #define ECR_CAP_MASK 0x0000001f /* Event range, 0-31 */ |
| #define OGW0 0x11608 |
| #define OGW1 0x1160c |
| #define EG0 0x11610 |
| #define EG1 0x11614 |
| #define EG2 0x11618 |
| #define EG3 0x1161c |
| #define EG4 0x11620 |
| #define EG5 0x11624 |
| #define EG6 0x11628 |
| #define EG7 0x1162c |
| #define PXW 0x11664 |
| #define PXWL 0x11680 |
| #define LCFUSE02 0x116c0 |
| #define LCFUSE_HIV_MASK 0x000000ff |
| #define CSIPLL0 0x12c10 |
| #define DDRMPLL1 0X12c20 |
| #define PEG_BAND_GAP_DATA 0x14d68 |
| |
| #define GEN6_GT_THREAD_STATUS_REG 0x13805c |
| #define GEN6_GT_THREAD_STATUS_CORE_MASK 0x7 |
| #define GEN6_GT_THREAD_STATUS_CORE_MASK_HSW (0x7 | (0x07 << 16)) |
| |
| #define GEN6_GT_PERF_STATUS 0x145948 |
| #define GEN6_RP_STATE_LIMITS 0x145994 |
| #define GEN6_RP_STATE_CAP 0x145998 |
| |
| /* |
| * Logical Context regs |
| */ |
| #define CCID 0x2180 |
| #define CCID_EN (1<<0) |
| #define CXT_SIZE 0x21a0 |
| #define GEN6_CXT_POWER_SIZE(cxt_reg) ((cxt_reg >> 24) & 0x3f) |
| #define GEN6_CXT_RING_SIZE(cxt_reg) ((cxt_reg >> 18) & 0x3f) |
| #define GEN6_CXT_RENDER_SIZE(cxt_reg) ((cxt_reg >> 12) & 0x3f) |
| #define GEN6_CXT_EXTENDED_SIZE(cxt_reg) ((cxt_reg >> 6) & 0x3f) |
| #define GEN6_CXT_PIPELINE_SIZE(cxt_reg) ((cxt_reg >> 0) & 0x3f) |
| #define GEN6_CXT_TOTAL_SIZE(cxt_reg) (GEN6_CXT_POWER_SIZE(cxt_reg) + \ |
| GEN6_CXT_RING_SIZE(cxt_reg) + \ |
| GEN6_CXT_RENDER_SIZE(cxt_reg) + \ |
| GEN6_CXT_EXTENDED_SIZE(cxt_reg) + \ |
| GEN6_CXT_PIPELINE_SIZE(cxt_reg)) |
| #define GEN7_CXT_SIZE 0x21a8 |
| #define GEN7_CXT_POWER_SIZE(ctx_reg) ((ctx_reg >> 25) & 0x7f) |
| #define GEN7_CXT_RING_SIZE(ctx_reg) ((ctx_reg >> 22) & 0x7) |
| #define GEN7_CXT_RENDER_SIZE(ctx_reg) ((ctx_reg >> 16) & 0x3f) |
| #define GEN7_CXT_EXTENDED_SIZE(ctx_reg) ((ctx_reg >> 9) & 0x7f) |
| #define GEN7_CXT_GT1_SIZE(ctx_reg) ((ctx_reg >> 6) & 0x7) |
| #define GEN7_CXT_VFSTATE_SIZE(ctx_reg) ((ctx_reg >> 0) & 0x3f) |
| #define GEN7_CXT_TOTAL_SIZE(ctx_reg) (GEN7_CXT_POWER_SIZE(ctx_reg) + \ |
| GEN7_CXT_RING_SIZE(ctx_reg) + \ |
| GEN7_CXT_RENDER_SIZE(ctx_reg) + \ |
| GEN7_CXT_EXTENDED_SIZE(ctx_reg) + \ |
| GEN7_CXT_GT1_SIZE(ctx_reg) + \ |
| GEN7_CXT_VFSTATE_SIZE(ctx_reg)) |
| #define HSW_CXT_POWER_SIZE(ctx_reg) ((ctx_reg >> 26) & 0x3f) |
| #define HSW_CXT_RING_SIZE(ctx_reg) ((ctx_reg >> 23) & 0x7) |
| #define HSW_CXT_RENDER_SIZE(ctx_reg) ((ctx_reg >> 15) & 0xff) |
| #define HSW_CXT_TOTAL_SIZE(ctx_reg) (HSW_CXT_POWER_SIZE(ctx_reg) + \ |
| HSW_CXT_RING_SIZE(ctx_reg) + \ |
| HSW_CXT_RENDER_SIZE(ctx_reg) + \ |
| GEN7_CXT_VFSTATE_SIZE(ctx_reg)) |
| |
| |
| /* |
| * Overlay regs |
| */ |
| |
| #define OVADD 0x30000 |
| #define DOVSTA 0x30008 |
| #define OC_BUF (0x3<<20) |
| #define OGAMC5 0x30010 |
| #define OGAMC4 0x30014 |
| #define OGAMC3 0x30018 |
| #define OGAMC2 0x3001c |
| #define OGAMC1 0x30020 |
| #define OGAMC0 0x30024 |
| |
| /* |
| * Display engine regs |
| */ |
| |
| /* Pipe A timing regs */ |
| #define _HTOTAL_A 0x60000 |
| #define _HBLANK_A 0x60004 |
| #define _HSYNC_A 0x60008 |
| #define _VTOTAL_A 0x6000c |
| #define _VBLANK_A 0x60010 |
| #define _VSYNC_A 0x60014 |
| #define _PIPEASRC 0x6001c |
| #define _BCLRPAT_A 0x60020 |
| #define _VSYNCSHIFT_A 0x60028 |
| |
| /* Pipe B timing regs */ |
| #define _HTOTAL_B 0x61000 |
| #define _HBLANK_B 0x61004 |
| #define _HSYNC_B 0x61008 |
| #define _VTOTAL_B 0x6100c |
| #define _VBLANK_B 0x61010 |
| #define _VSYNC_B 0x61014 |
| #define _PIPEBSRC 0x6101c |
| #define _BCLRPAT_B 0x61020 |
| #define _VSYNCSHIFT_B 0x61028 |
| |
| |
| #define HTOTAL(pipe) _PIPE(pipe, _HTOTAL_A, _HTOTAL_B) |
| #define HBLANK(pipe) _PIPE(pipe, _HBLANK_A, _HBLANK_B) |
| #define HSYNC(pipe) _PIPE(pipe, _HSYNC_A, _HSYNC_B) |
| #define VTOTAL(pipe) _PIPE(pipe, _VTOTAL_A, _VTOTAL_B) |
| #define VBLANK(pipe) _PIPE(pipe, _VBLANK_A, _VBLANK_B) |
| #define VSYNC(pipe) _PIPE(pipe, _VSYNC_A, _VSYNC_B) |
| #define BCLRPAT(pipe) _PIPE(pipe, _BCLRPAT_A, _BCLRPAT_B) |
| #define VSYNCSHIFT(pipe) _PIPE(pipe, _VSYNCSHIFT_A, _VSYNCSHIFT_B) |
| |
| /* VGA port control */ |
| #define ADPA 0x61100 |
| #define PCH_ADPA 0xe1100 |
| #define VLV_ADPA (VLV_DISPLAY_BASE + ADPA) |
| |
| #define ADPA_DAC_ENABLE (1<<31) |
| #define ADPA_DAC_DISABLE 0 |
| #define ADPA_PIPE_SELECT_MASK (1<<30) |
| #define ADPA_PIPE_A_SELECT 0 |
| #define ADPA_PIPE_B_SELECT (1<<30) |
| #define ADPA_PIPE_SELECT(pipe) ((pipe) << 30) |
| /* CPT uses bits 29:30 for pch transcoder select */ |
| #define ADPA_CRT_HOTPLUG_MASK 0x03ff0000 /* bit 25-16 */ |
| #define ADPA_CRT_HOTPLUG_MONITOR_NONE (0<<24) |
| #define ADPA_CRT_HOTPLUG_MONITOR_MASK (3<<24) |
| #define ADPA_CRT_HOTPLUG_MONITOR_COLOR (3<<24) |
| #define ADPA_CRT_HOTPLUG_MONITOR_MONO (2<<24) |
| #define ADPA_CRT_HOTPLUG_ENABLE (1<<23) |
| #define ADPA_CRT_HOTPLUG_PERIOD_64 (0<<22) |
| #define ADPA_CRT_HOTPLUG_PERIOD_128 (1<<22) |
| #define ADPA_CRT_HOTPLUG_WARMUP_5MS (0<<21) |
| #define ADPA_CRT_HOTPLUG_WARMUP_10MS (1<<21) |
| #define ADPA_CRT_HOTPLUG_SAMPLE_2S (0<<20) |
| #define ADPA_CRT_HOTPLUG_SAMPLE_4S (1<<20) |
| #define ADPA_CRT_HOTPLUG_VOLTAGE_40 (0<<18) |
| #define ADPA_CRT_HOTPLUG_VOLTAGE_50 (1<<18) |
| #define ADPA_CRT_HOTPLUG_VOLTAGE_60 (2<<18) |
| #define ADPA_CRT_HOTPLUG_VOLTAGE_70 (3<<18) |
| #define ADPA_CRT_HOTPLUG_VOLREF_325MV (0<<17) |
| #define ADPA_CRT_HOTPLUG_VOLREF_475MV (1<<17) |
| #define ADPA_CRT_HOTPLUG_FORCE_TRIGGER (1<<16) |
| #define ADPA_USE_VGA_HVPOLARITY (1<<15) |
| #define ADPA_SETS_HVPOLARITY 0 |
| #define ADPA_VSYNC_CNTL_DISABLE (1<<11) |
| #define ADPA_VSYNC_CNTL_ENABLE 0 |
| #define ADPA_HSYNC_CNTL_DISABLE (1<<10) |
| #define ADPA_HSYNC_CNTL_ENABLE 0 |
| #define ADPA_VSYNC_ACTIVE_HIGH (1<<4) |
| #define ADPA_VSYNC_ACTIVE_LOW 0 |
| #define ADPA_HSYNC_ACTIVE_HIGH (1<<3) |
| #define ADPA_HSYNC_ACTIVE_LOW 0 |
| #define ADPA_DPMS_MASK (~(3<<10)) |
| #define ADPA_DPMS_ON (0<<10) |
| #define ADPA_DPMS_SUSPEND (1<<10) |
| #define ADPA_DPMS_STANDBY (2<<10) |
| #define ADPA_DPMS_OFF (3<<10) |
| |
| |
| /* Hotplug control (945+ only) */ |
| #define PORT_HOTPLUG_EN 0x61110 |
| #define HDMIB_HOTPLUG_INT_EN (1 << 29) |
| #define DPB_HOTPLUG_INT_EN (1 << 29) |
| #define HDMIC_HOTPLUG_INT_EN (1 << 28) |
| #define DPC_HOTPLUG_INT_EN (1 << 28) |
| #define HDMID_HOTPLUG_INT_EN (1 << 27) |
| #define DPD_HOTPLUG_INT_EN (1 << 27) |
| #define SDVOB_HOTPLUG_INT_EN (1 << 26) |
| #define SDVOC_HOTPLUG_INT_EN (1 << 25) |
| #define TV_HOTPLUG_INT_EN (1 << 18) |
| #define CRT_HOTPLUG_INT_EN (1 << 9) |
| #define CRT_HOTPLUG_FORCE_DETECT (1 << 3) |
| #define CRT_HOTPLUG_ACTIVATION_PERIOD_32 (0 << 8) |
| /* must use period 64 on GM45 according to docs */ |
| #define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8) |
| #define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7) |
| #define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7) |
| #define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5) |
| #define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5) |
| #define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5) |
| #define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5) |
| #define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5) |
| #define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4) |
| #define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4) |
| #define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2) |
| #define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2) |
| |
| #define PORT_HOTPLUG_STAT 0x61114 |
| /* HDMI/DP bits are gen4+ */ |
| #define DPB_HOTPLUG_LIVE_STATUS (1 << 29) |
| #define DPC_HOTPLUG_LIVE_STATUS (1 << 28) |
| #define DPD_HOTPLUG_LIVE_STATUS (1 << 27) |
| #define DPD_HOTPLUG_INT_STATUS (3 << 21) |
| #define DPC_HOTPLUG_INT_STATUS (3 << 19) |
| #define DPB_HOTPLUG_INT_STATUS (3 << 17) |
| /* HDMI bits are shared with the DP bits */ |
| #define HDMIB_HOTPLUG_LIVE_STATUS (1 << 29) |
| #define HDMIC_HOTPLUG_LIVE_STATUS (1 << 28) |
| #define HDMID_HOTPLUG_LIVE_STATUS (1 << 27) |
| #define HDMID_HOTPLUG_INT_STATUS (3 << 21) |
| #define HDMIC_HOTPLUG_INT_STATUS (3 << 19) |
| #define HDMIB_HOTPLUG_INT_STATUS (3 << 17) |
| /* CRT/TV common between gen3+ */ |
| #define CRT_HOTPLUG_INT_STATUS (1 << 11) |
| #define TV_HOTPLUG_INT_STATUS (1 << 10) |
| #define CRT_HOTPLUG_MONITOR_MASK (3 << 8) |
| #define CRT_HOTPLUG_MONITOR_COLOR (3 << 8) |
| #define CRT_HOTPLUG_MONITOR_MONO (2 << 8) |
| #define CRT_HOTPLUG_MONITOR_NONE (0 << 8) |
| /* SDVO is different across gen3/4 */ |
| #define SDVOC_HOTPLUG_INT_STATUS_G4X (1 << 3) |
| #define SDVOB_HOTPLUG_INT_STATUS_G4X (1 << 2) |
| #define SDVOC_HOTPLUG_INT_STATUS_I965 (3 << 4) |
| #define SDVOB_HOTPLUG_INT_STATUS_I965 (3 << 2) |
| #define SDVOC_HOTPLUG_INT_STATUS_I915 (1 << 7) |
| #define SDVOB_HOTPLUG_INT_STATUS_I915 (1 << 6) |
| |
| /* SDVO port control */ |
| #define SDVOB 0x61140 |
| #define SDVOC 0x61160 |
| #define SDVO_ENABLE (1 << 31) |
| #define SDVO_PIPE_B_SELECT (1 << 30) |
| #define SDVO_STALL_SELECT (1 << 29) |
| #define SDVO_INTERRUPT_ENABLE (1 << 26) |
| /** |
| * 915G/GM SDVO pixel multiplier. |
| * |
| * Programmed value is multiplier - 1, up to 5x. |
| * |
| * \sa DPLL_MD_UDI_MULTIPLIER_MASK |
| */ |
| #define SDVO_PORT_MULTIPLY_MASK (7 << 23) |
| #define SDVO_PORT_MULTIPLY_SHIFT 23 |
| #define SDVO_PHASE_SELECT_MASK (15 << 19) |
| #define SDVO_PHASE_SELECT_DEFAULT (6 << 19) |
| #define SDVO_CLOCK_OUTPUT_INVERT (1 << 18) |
| #define SDVOC_GANG_MODE (1 << 16) |
| #define SDVO_ENCODING_SDVO (0x0 << 10) |
| #define SDVO_ENCODING_HDMI (0x2 << 10) |
| /** Requird for HDMI operation */ |
| #define SDVO_NULL_PACKETS_DURING_VSYNC (1 << 9) |
| #define SDVO_COLOR_RANGE_16_235 (1 << 8) |
| #define SDVO_BORDER_ENABLE (1 << 7) |
| #define SDVO_AUDIO_ENABLE (1 << 6) |
| /** New with 965, default is to be set */ |
| #define SDVO_VSYNC_ACTIVE_HIGH (1 << 4) |
| /** New with 965, default is to be set */ |
| #define SDVO_HSYNC_ACTIVE_HIGH (1 << 3) |
| #define SDVOB_PCIE_CONCURRENCY (1 << 3) |
| #define SDVO_DETECTED (1 << 2) |
| /* Bits to be preserved when writing */ |
| #define SDVOB_PRESERVE_MASK ((1 << 17) | (1 << 16) | (1 << 14) | (1 << 26)) |
| #define SDVOC_PRESERVE_MASK ((1 << 17) | (1 << 26)) |
| |
| /* DVO port control */ |
| #define DVOA 0x61120 |
| #define DVOB 0x61140 |
| #define DVOC 0x61160 |
| #define DVO_ENABLE (1 << 31) |
| #define DVO_PIPE_B_SELECT (1 << 30) |
| #define DVO_PIPE_STALL_UNUSED (0 << 28) |
| #define DVO_PIPE_STALL (1 << 28) |
| #define DVO_PIPE_STALL_TV (2 << 28) |
| #define DVO_PIPE_STALL_MASK (3 << 28) |
| #define DVO_USE_VGA_SYNC (1 << 15) |
| #define DVO_DATA_ORDER_I740 (0 << 14) |
| #define DVO_DATA_ORDER_FP (1 << 14) |
| #define DVO_VSYNC_DISABLE (1 << 11) |
| #define DVO_HSYNC_DISABLE (1 << 10) |
| #define DVO_VSYNC_TRISTATE (1 << 9) |
| #define DVO_HSYNC_TRISTATE (1 << 8) |
| #define DVO_BORDER_ENABLE (1 << 7) |
| #define DVO_DATA_ORDER_GBRG (1 << 6) |
| #define DVO_DATA_ORDER_RGGB (0 << 6) |
| #define DVO_DATA_ORDER_GBRG_ERRATA (0 << 6) |
| #define DVO_DATA_ORDER_RGGB_ERRATA (1 << 6) |
| #define DVO_VSYNC_ACTIVE_HIGH (1 << 4) |
| #define DVO_HSYNC_ACTIVE_HIGH (1 << 3) |
| #define DVO_BLANK_ACTIVE_HIGH (1 << 2) |
| #define DVO_OUTPUT_CSTATE_PIXELS (1 << 1) /* SDG only */ |
| #define DVO_OUTPUT_SOURCE_SIZE_PIXELS (1 << 0) /* SDG only */ |
| #define DVO_PRESERVE_MASK (0x7<<24) |
| #define DVOA_SRCDIM 0x61124 |
| #define DVOB_SRCDIM 0x61144 |
| #define DVOC_SRCDIM 0x61164 |
| #define DVO_SRCDIM_HORIZONTAL_SHIFT 12 |
| #define DVO_SRCDIM_VERTICAL_SHIFT 0 |
| |
| /* LVDS port control */ |
| #define LVDS 0x61180 |
| /* |
| * Enables the LVDS port. This bit must be set before DPLLs are enabled, as |
| * the DPLL semantics change when the LVDS is assigned to that pipe. |
| */ |
| #define LVDS_PORT_EN (1 << 31) |
| /* Selects pipe B for LVDS data. Must be set on pre-965. */ |
| #define LVDS_PIPEB_SELECT (1 << 30) |
| #define LVDS_PIPE_MASK (1 << 30) |
| #define LVDS_PIPE(pipe) ((pipe) << 30) |
| /* LVDS dithering flag on 965/g4x platform */ |
| #define LVDS_ENABLE_DITHER (1 << 25) |
| /* LVDS sync polarity flags. Set to invert (i.e. negative) */ |
| #define LVDS_VSYNC_POLARITY (1 << 21) |
| #define LVDS_HSYNC_POLARITY (1 << 20) |
| |
| /* Enable border for unscaled (or aspect-scaled) display */ |
| #define LVDS_BORDER_ENABLE (1 << 15) |
| /* |
| * Enables the A0-A2 data pairs and CLKA, containing 18 bits of color data per |
| * pixel. |
| */ |
| #define LVDS_A0A2_CLKA_POWER_MASK (3 << 8) |
| #define LVDS_A0A2_CLKA_POWER_DOWN (0 << 8) |
| #define LVDS_A0A2_CLKA_POWER_UP (3 << 8) |
| /* |
| * Controls the A3 data pair, which contains the additional LSBs for 24 bit |
| * mode. Only enabled if LVDS_A0A2_CLKA_POWER_UP also indicates it should be |
| * on. |
| */ |
| #define LVDS_A3_POWER_MASK (3 << 6) |
| #define LVDS_A3_POWER_DOWN (0 << 6) |
| #define LVDS_A3_POWER_UP (3 << 6) |
| /* |
| * Controls the CLKB pair. This should only be set when LVDS_B0B3_POWER_UP |
| * is set. |
| */ |
| #define LVDS_CLKB_POWER_MASK (3 << 4) |
| #define LVDS_CLKB_POWER_DOWN (0 << 4) |
| #define LVDS_CLKB_POWER_UP (3 << 4) |
| /* |
| * Controls the B0-B3 data pairs. This must be set to match the DPLL p2 |
| * setting for whether we are in dual-channel mode. The B3 pair will |
| * additionally only be powered up when LVDS_A3_POWER_UP is set. |
| */ |
| #define LVDS_B0B3_POWER_MASK (3 << 2) |
| #define LVDS_B0B3_POWER_DOWN (0 << 2) |
| #define LVDS_B0B3_POWER_UP (3 << 2) |
| |
| /* Video Data Island Packet control */ |
| #define VIDEO_DIP_DATA 0x61178 |
| #define VIDEO_DIP_CTL 0x61170 |
| /* Pre HSW: */ |
| #define VIDEO_DIP_ENABLE (1 << 31) |
| #define VIDEO_DIP_PORT_B (1 << 29) |
| #define VIDEO_DIP_PORT_C (2 << 29) |
| #define VIDEO_DIP_PORT_D (3 << 29) |
| #define VIDEO_DIP_PORT_MASK (3 << 29) |
| #define VIDEO_DIP_ENABLE_GCP (1 << 25) |
| #define VIDEO_DIP_ENABLE_AVI (1 << 21) |
| #define VIDEO_DIP_ENABLE_VENDOR (2 << 21) |
| #define VIDEO_DIP_ENABLE_GAMUT (4 << 21) |
| #define VIDEO_DIP_ENABLE_SPD (8 << 21) |
| #define VIDEO_DIP_SELECT_AVI (0 << 19) |
| #define VIDEO_DIP_SELECT_VENDOR (1 << 19) |
| #define VIDEO_DIP_SELECT_SPD (3 << 19) |
| #define VIDEO_DIP_SELECT_MASK (3 << 19) |
| #define VIDEO_DIP_FREQ_ONCE (0 << 16) |
| #define VIDEO_DIP_FREQ_VSYNC (1 << 16) |
| #define VIDEO_DIP_FREQ_2VSYNC (2 << 16) |
| #define VIDEO_DIP_FREQ_MASK (3 << 16) |
| /* HSW and later: */ |
| #define VIDEO_DIP_ENABLE_VSC_HSW (1 << 20) |
| #define VIDEO_DIP_ENABLE_GCP_HSW (1 << 16) |
| #define VIDEO_DIP_ENABLE_AVI_HSW (1 << 12) |
| #define VIDEO_DIP_ENABLE_VS_HSW (1 << 8) |
| #define VIDEO_DIP_ENABLE_GMP_HSW (1 << 4) |
| #define VIDEO_DIP_ENABLE_SPD_HSW (1 << 0) |
| |
| /* Panel power sequencing */ |
| #define PP_STATUS 0x61200 |
| #define PP_ON (1 << 31) |
| /* |
| * Indicates that all dependencies of the panel are on: |
| * |
| * - PLL enabled |
| * - pipe enabled |
| * - LVDS/DVOB/DVOC on |
| */ |
| #define PP_READY (1 << 30) |
| #define PP_SEQUENCE_NONE (0 << 28) |
| #define PP_SEQUENCE_POWER_UP (1 << 28) |
| #define PP_SEQUENCE_POWER_DOWN (2 << 28) |
| #define PP_SEQUENCE_MASK (3 << 28) |
| #define PP_SEQUENCE_SHIFT 28 |
| #define PP_CYCLE_DELAY_ACTIVE (1 << 27) |
| #define PP_SEQUENCE_STATE_MASK 0x0000000f |
| #define PP_SEQUENCE_STATE_OFF_IDLE (0x0 << 0) |
| #define PP_SEQUENCE_STATE_OFF_S0_1 (0x1 << 0) |
| #define PP_SEQUENCE_STATE_OFF_S0_2 (0x2 << 0) |
| #define PP_SEQUENCE_STATE_OFF_S0_3 (0x3 << 0) |
| #define PP_SEQUENCE_STATE_ON_IDLE (0x8 << 0) |
| #define PP_SEQUENCE_STATE_ON_S1_0 (0x9 << 0) |
| #define PP_SEQUENCE_STATE_ON_S1_2 (0xa << 0) |
| #define PP_SEQUENCE_STATE_ON_S1_3 (0xb << 0) |
| #define PP_SEQUENCE_STATE_RESET (0xf << 0) |
| #define PP_CONTROL 0x61204 |
| #define POWER_TARGET_ON (1 << 0) |
| #define PP_ON_DELAYS 0x61208 |
| #define PP_OFF_DELAYS 0x6120c |
| #define PP_DIVISOR 0x61210 |
| |
| /* Panel fitting */ |
| #define PFIT_CONTROL 0x61230 |
| #define PFIT_ENABLE (1 << 31) |
| #define PFIT_PIPE_MASK (3 << 29) |
| #define PFIT_PIPE_SHIFT 29 |
| #define VERT_INTERP_DISABLE (0 << 10) |
| #define VERT_INTERP_BILINEAR (1 << 10) |
| #define VERT_INTERP_MASK (3 << 10) |
| #define VERT_AUTO_SCALE (1 << 9) |
| #define HORIZ_INTERP_DISABLE (0 << 6) |
| #define HORIZ_INTERP_BILINEAR (1 << 6) |
| #define HORIZ_INTERP_MASK (3 << 6) |
| #define HORIZ_AUTO_SCALE (1 << 5) |
| #define PANEL_8TO6_DITHER_ENABLE (1 << 3) |
| #define PFIT_FILTER_FUZZY (0 << 24) |
| #define PFIT_SCALING_AUTO (0 << 26) |
| #define PFIT_SCALING_PROGRAMMED (1 << 26) |
| #define PFIT_SCALING_PILLAR (2 << 26) |
| #define PFIT_SCALING_LETTER (3 << 26) |
| #define PFIT_PGM_RATIOS 0x61234 |
| #define PFIT_VERT_SCALE_MASK 0xfff00000 |
| #define PFIT_HORIZ_SCALE_MASK 0x0000fff0 |
| /* Pre-965 */ |
| #define PFIT_VERT_SCALE_SHIFT 20 |
| #define PFIT_VERT_SCALE_MASK 0xfff00000 |
| #define PFIT_HORIZ_SCALE_SHIFT 4 |
| #define PFIT_HORIZ_SCALE_MASK 0x0000fff0 |
| /* 965+ */ |
| #define PFIT_VERT_SCALE_SHIFT_965 16 |
| #define PFIT_VERT_SCALE_MASK_965 0x1fff0000 |
| #define PFIT_HORIZ_SCALE_SHIFT_965 0 |
| #define PFIT_HORIZ_SCALE_MASK_965 0x00001fff |
| |
| #define PFIT_AUTO_RATIOS 0x61238 |
| |
| /* Backlight control */ |
| #define BLC_PWM_CTL2 0x61250 /* 965+ only */ |
| #define BLM_PWM_ENABLE (1 << 31) |
| #define BLM_COMBINATION_MODE (1 << 30) /* gen4 only */ |
| #define BLM_PIPE_SELECT (1 << 29) |
| #define BLM_PIPE_SELECT_IVB (3 << 29) |
| #define BLM_PIPE_A (0 << 29) |
| #define BLM_PIPE_B (1 << 29) |
| #define BLM_PIPE_C (2 << 29) /* ivb + */ |
| #define BLM_PIPE(pipe) ((pipe) << 29) |
| #define BLM_POLARITY_I965 (1 << 28) /* gen4 only */ |
| #define BLM_PHASE_IN_INTERUPT_STATUS (1 << 26) |
| #define BLM_PHASE_IN_ENABLE (1 << 25) |
| #define BLM_PHASE_IN_INTERUPT_ENABL (1 << 24) |
| #define BLM_PHASE_IN_TIME_BASE_SHIFT (16) |
| #define BLM_PHASE_IN_TIME_BASE_MASK (0xff << 16) |
| #define BLM_PHASE_IN_COUNT_SHIFT (8) |
| #define BLM_PHASE_IN_COUNT_MASK (0xff << 8) |
| #define BLM_PHASE_IN_INCR_SHIFT (0) |
| #define BLM_PHASE_IN_INCR_MASK (0xff << 0) |
| #define BLC_PWM_CTL 0x61254 |
| /* |
| * This is the most significant 15 bits of the number of backlight cycles in a |
| * complete cycle of the modulated backlight control. |
| * |
| * The actual value is this field multiplied by two. |
| */ |
| #define BACKLIGHT_MODULATION_FREQ_SHIFT (17) |
| #define BACKLIGHT_MODULATION_FREQ_MASK (0x7fff << 17) |
| #define BLM_LEGACY_MODE (1 << 16) /* gen2 only */ |
| /* |
| * This is the number of cycles out of the backlight modulation cycle for which |
| * the backlight is on. |
| * |
| * This field must be no greater than the number of cycles in the complete |
| * backlight modulation cycle. |
| */ |
| #define BACKLIGHT_DUTY_CYCLE_SHIFT (0) |
| #define BACKLIGHT_DUTY_CYCLE_MASK (0xffff) |
| #define BACKLIGHT_DUTY_CYCLE_MASK_PNV (0xfffe) |
| #define BLM_POLARITY_PNV (1 << 0) /* pnv only */ |
| |
| #define BLC_HIST_CTL 0x61260 |
| |
| /* New registers for PCH-split platforms. Safe where new bits show up, the |
| * register layout machtes with gen4 BLC_PWM_CTL[12]. */ |
| #define BLC_PWM_CPU_CTL2 0x48250 |
| #define BLC_PWM_CPU_CTL 0x48254 |
| |
| /* PCH CTL1 is totally different, all but the below bits are reserved. CTL2 is |
| * like the normal CTL from gen4 and earlier. Hooray for confusing naming. */ |
| #define BLC_PWM_PCH_CTL1 0xc8250 |
| #define BLM_PCH_PWM_ENABLE (1 << 31) |
| #define BLM_PCH_OVERRIDE_ENABLE (1 << 30) |
| #define BLM_PCH_POLARITY (1 << 29) |
| #define BLC_PWM_PCH_CTL2 0xc8254 |
| |
| /* TV port control */ |
| #define TV_CTL 0x68000 |
| /** Enables the TV encoder */ |
| # define TV_ENC_ENABLE (1 << 31) |
| /** Sources the TV encoder input from pipe B instead of A. */ |
| # define TV_ENC_PIPEB_SELECT (1 << 30) |
| /** Outputs composite video (DAC A only) */ |
| # define TV_ENC_OUTPUT_COMPOSITE (0 << 28) |
| /** Outputs SVideo video (DAC B/C) */ |
| # define TV_ENC_OUTPUT_SVIDEO (1 << 28) |
| /** Outputs Component video (DAC A/B/C) */ |
| # define TV_ENC_OUTPUT_COMPONENT (2 << 28) |
| /** Outputs Composite and SVideo (DAC A/B/C) */ |
| # define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28) |
| # define TV_TRILEVEL_SYNC (1 << 21) |
| /** Enables slow sync generation (945GM only) */ |
| # define TV_SLOW_SYNC (1 << 20) |
| /** Selects 4x oversampling for 480i and 576p */ |
| # define TV_OVERSAMPLE_4X (0 << 18) |
| /** Selects 2x oversampling for 720p and 1080i */ |
| # define TV_OVERSAMPLE_2X (1 << 18) |
| /** Selects no oversampling for 1080p */ |
| # define TV_OVERSAMPLE_NONE (2 << 18) |
| /** Selects 8x oversampling */ |
| # define TV_OVERSAMPLE_8X (3 << 18) |
| /** Selects progressive mode rather than interlaced */ |
| # define TV_PROGRESSIVE (1 << 17) |
| /** Sets the colorburst to PAL mode. Required for non-M PAL modes. */ |
| # define TV_PAL_BURST (1 << 16) |
| /** Field for setting delay of Y compared to C */ |
| # define TV_YC_SKEW_MASK (7 << 12) |
| /** Enables a fix for 480p/576p standard definition modes on the 915GM only */ |
| # define TV_ENC_SDP_FIX (1 << 11) |
| /** |
| * Enables a fix for the 915GM only. |
| * |
| * Not sure what it does. |
| */ |
| # define TV_ENC_C0_FIX (1 << 10) |
| /** Bits that must be preserved by software */ |
| # define TV_CTL_SAVE ((1 << 11) | (3 << 9) | (7 << 6) | 0xf) |
| # define TV_FUSE_STATE_MASK (3 << 4) |
| /** Read-only state that reports all features enabled */ |
| # define TV_FUSE_STATE_ENABLED (0 << 4) |
| /** Read-only state that reports that Macrovision is disabled in hardware*/ |
| # define TV_FUSE_STATE_NO_MACROVISION (1 << 4) |
| /** Read-only state that reports that TV-out is disabled in hardware. */ |
| # define TV_FUSE_STATE_DISABLED (2 << 4) |
| /** Normal operation */ |
| # define TV_TEST_MODE_NORMAL (0 << 0) |
| /** Encoder test pattern 1 - combo pattern */ |
| # define TV_TEST_MODE_PATTERN_1 (1 << 0) |
| /** Encoder test pattern 2 - full screen vertical 75% color bars */ |
| # define TV_TEST_MODE_PATTERN_2 (2 << 0) |
| /** Encoder test pattern 3 - full screen horizontal 75% color bars */ |
| # define TV_TEST_MODE_PATTERN_3 (3 << 0) |
| /** Encoder test pattern 4 - random noise */ |
| # define TV_TEST_MODE_PATTERN_4 (4 << 0) |
| /** Encoder test pattern 5 - linear color ramps */ |
| # define TV_TEST_MODE_PATTERN_5 (5 << 0) |
| /** |
| * This test mode forces the DACs to 50% of full output. |
| * |
| * This is used for load detection in combination with TVDAC_SENSE_MASK |
| */ |
| # define TV_TEST_MODE_MONITOR_DETECT (7 << 0) |
| # define TV_TEST_MODE_MASK (7 << 0) |
| |
| #define TV_DAC 0x68004 |
| # define TV_DAC_SAVE 0x00ffff00 |
| /** |
| * Reports that DAC state change logic has reported change (RO). |
| * |
| * This gets cleared when TV_DAC_STATE_EN is cleared |
| */ |
| # define TVDAC_STATE_CHG (1 << 31) |
| # define TVDAC_SENSE_MASK (7 << 28) |
| /** Reports that DAC A voltage is above the detect threshold */ |
| # define TVDAC_A_SENSE (1 << 30) |
| /** Reports that DAC B voltage is above the detect threshold */ |
| # define TVDAC_B_SENSE (1 << 29) |
| /** Reports that DAC C voltage is above the detect threshold */ |
| # define TVDAC_C_SENSE (1 << 28) |
| /** |
| * Enables DAC state detection logic, for load-based TV detection. |
| * |
| * The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set |
| * to off, for load detection to work. |
| */ |
| # define TVDAC_STATE_CHG_EN (1 << 27) |
| /** Sets the DAC A sense value to high */ |
| # define TVDAC_A_SENSE_CTL (1 << 26) |
| /** Sets the DAC B sense value to high */ |
| # define TVDAC_B_SENSE_CTL (1 << 25) |
| /** Sets the DAC C sense value to high */ |
| # define TVDAC_C_SENSE_CTL (1 << 24) |
| /** Overrides the ENC_ENABLE and DAC voltage levels */ |
| # define DAC_CTL_OVERRIDE (1 << 7) |
| /** Sets the slew rate. Must be preserved in software */ |
| # define ENC_TVDAC_SLEW_FAST (1 << 6) |
| # define DAC_A_1_3_V (0 << 4) |
| # define DAC_A_1_1_V (1 << 4) |
| # define DAC_A_0_7_V (2 << 4) |
| # define DAC_A_MASK (3 << 4) |
| # define DAC_B_1_3_V (0 << 2) |
| # define DAC_B_1_1_V (1 << 2) |
| # define DAC_B_0_7_V (2 << 2) |
| # define DAC_B_MASK (3 << 2) |
| # define DAC_C_1_3_V (0 << 0) |
| # define DAC_C_1_1_V (1 << 0) |
| # define DAC_C_0_7_V (2 << 0) |
| # define DAC_C_MASK (3 << 0) |
| |
| /** |
| * CSC coefficients are stored in a floating point format with 9 bits of |
| * mantissa and 2 or 3 bits of exponent. The exponent is represented as 2**-n, |
| * where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with |
| * -1 (0x3) being the only legal negative value. |
| */ |
| #define TV_CSC_Y 0x68010 |
| # define TV_RY_MASK 0x07ff0000 |
| # define TV_RY_SHIFT 16 |
| # define TV_GY_MASK 0x00000fff |
| # define TV_GY_SHIFT 0 |
| |
| #define TV_CSC_Y2 0x68014 |
| # define TV_BY_MASK 0x07ff0000 |
| # define TV_BY_SHIFT 16 |
| /** |
| * Y attenuation for component video. |
| * |
| * Stored in 1.9 fixed point. |
| */ |
| # define TV_AY_MASK 0x000003ff |
| # define TV_AY_SHIFT 0 |
| |
| #define TV_CSC_U 0x68018 |
| # define TV_RU_MASK 0x07ff0000 |
| # define TV_RU_SHIFT 16 |
| # define TV_GU_MASK 0x000007ff |
| # define TV_GU_SHIFT 0 |
| |
| #define TV_CSC_U2 0x6801c |
| # define TV_BU_MASK 0x07ff0000 |
| # define TV_BU_SHIFT 16 |
| /** |
| * U attenuation for component video. |
| * |
| * Stored in 1.9 fixed point. |
| */ |
| # define TV_AU_MASK 0x000003ff |
| # define TV_AU_SHIFT 0 |
| |
| #define TV_CSC_V 0x68020 |
| # define TV_RV_MASK 0x0fff0000 |
| # define TV_RV_SHIFT 16 |
| # define TV_GV_MASK 0x000007ff |
| # define TV_GV_SHIFT 0 |
| |
| #define TV_CSC_V2 0x68024 |
| # define TV_BV_MASK 0x07ff0000 |
| # define TV_BV_SHIFT 16 |
| /** |
| * V attenuation for component video. |
| * |
| * Stored in 1.9 fixed point. |
| */ |
| # define TV_AV_MASK 0x000007ff |
| # define TV_AV_SHIFT 0 |
| |
| #define TV_CLR_KNOBS 0x68028 |
| /** 2s-complement brightness adjustment */ |
| # define TV_BRIGHTNESS_MASK 0xff000000 |
| # define TV_BRIGHTNESS_SHIFT 24 |
| /** Contrast adjustment, as a 2.6 unsigned floating point number */ |
| # define TV_CONTRAST_MASK 0x00ff0000 |
| # define TV_CONTRAST_SHIFT 16 |
| /** Saturation adjustment, as a 2.6 unsigned floating point number */ |
| # define TV_SATURATION_MASK 0x0000ff00 |
| # define TV_SATURATION_SHIFT 8 |
| /** Hue adjustment, as an integer phase angle in degrees */ |
| # define TV_HUE_MASK 0x000000ff |
| # define TV_HUE_SHIFT 0 |
| |
| #define TV_CLR_LEVEL 0x6802c |
| /** Controls the DAC level for black */ |
| # define TV_BLACK_LEVEL_MASK 0x01ff0000 |
| # define TV_BLACK_LEVEL_SHIFT 16 |
| /** Controls the DAC level for blanking */ |
| # define TV_BLANK_LEVEL_MASK 0x000001ff |
| # define TV_BLANK_LEVEL_SHIFT 0 |
| |
| #define TV_H_CTL_1 0x68030 |
| /** Number of pixels in the hsync. */ |
| # define TV_HSYNC_END_MASK 0x1fff0000 |
| # define TV_HSYNC_END_SHIFT 16 |
| /** Total number of pixels minus one in the line (display and blanking). */ |
| # define TV_HTOTAL_MASK 0x00001fff |
| # define TV_HTOTAL_SHIFT 0 |
| |
| #define TV_H_CTL_2 0x68034 |
| /** Enables the colorburst (needed for non-component color) */ |
| # define TV_BURST_ENA (1 << 31) |
| /** Offset of the colorburst from the start of hsync, in pixels minus one. */ |
| # define TV_HBURST_START_SHIFT 16 |
| # define TV_HBURST_START_MASK 0x1fff0000 |
| /** Length of the colorburst */ |
| # define TV_HBURST_LEN_SHIFT 0 |
| # define TV_HBURST_LEN_MASK 0x0001fff |
| |
| #define TV_H_CTL_3 0x68038 |
| /** End of hblank, measured in pixels minus one from start of hsync */ |
| # define TV_HBLANK_END_SHIFT 16 |
| # define TV_HBLANK_END_MASK 0x1fff0000 |
| /** Start of hblank, measured in pixels minus one from start of hsync */ |
| # define TV_HBLANK_START_SHIFT 0 |
| # define TV_HBLANK_START_MASK 0x0001fff |
| |
| #define TV_V_CTL_1 0x6803c |
| /** XXX */ |
| # define TV_NBR_END_SHIFT 16 |
| # define TV_NBR_END_MASK 0x07ff0000 |
| /** XXX */ |
| # define TV_VI_END_F1_SHIFT 8 |
| # define TV_VI_END_F1_MASK 0x00003f00 |
| /** XXX */ |
| # define TV_VI_END_F2_SHIFT 0 |
| # define TV_VI_END_F2_MASK 0x0000003f |
| |
| #define TV_V_CTL_2 0x68040 |
| /** Length of vsync, in half lines */ |
| # define TV_VSYNC_LEN_MASK 0x07ff0000 |
| # define TV_VSYNC_LEN_SHIFT 16 |
| /** Offset of the start of vsync in field 1, measured in one less than the |
| * number of half lines. |
| */ |
| # define TV_VSYNC_START_F1_MASK 0x00007f00 |
| # define TV_VSYNC_START_F1_SHIFT 8 |
| /** |
| * Offset of the start of vsync in field 2, measured in one less than the |
| * number of half lines. |
| */ |
| # define TV_VSYNC_START_F2_MASK 0x0000007f |
| # define TV_VSYNC_START_F2_SHIFT 0 |
| |
| #define TV_V_CTL_3 0x68044 |
| /** Enables generation of the equalization signal */ |
| # define TV_EQUAL_ENA (1 << 31) |
| /** Length of vsync, in half lines */ |
| # define TV_VEQ_LEN_MASK 0x007f0000 |
| # define TV_VEQ_LEN_SHIFT 16 |
| /** Offset of the start of equalization in field 1, measured in one less than |
| * the number of half lines. |
| */ |
| # define TV_VEQ_START_F1_MASK 0x0007f00 |
| # define TV_VEQ_START_F1_SHIFT 8 |
| /** |
| * Offset of the start of equalization in field 2, measured in one less than |
| * the number of half lines. |
| */ |
| # define TV_VEQ_START_F2_MASK 0x000007f |
| # define TV_VEQ_START_F2_SHIFT 0 |
| |
| #define TV_V_CTL_4 0x68048 |
| /** |
| * Offset to start of vertical colorburst, measured in one less than the |
| * number of lines from vertical start. |
| */ |
| # define TV_VBURST_START_F1_MASK 0x003f0000 |
| # define TV_VBURST_START_F1_SHIFT 16 |
| /** |
| * Offset to the end of vertical colorburst, measured in one less than the |
| * number of lines from the start of NBR. |
| */ |
| # define TV_VBURST_END_F1_MASK 0x000000ff |
| # define TV_VBURST_END_F1_SHIFT 0 |
| |
| #define TV_V_CTL_5 0x6804c |
| /** |
| * Offset to start of vertical colorburst, measured in one less than the |
| * number of lines from vertical start. |
| */ |
| # define TV_VBURST_START_F2_MASK 0x003f0000 |
| # define TV_VBURST_START_F2_SHIFT 16 |
| /** |
| * Offset to the end of vertical colorburst, measured in one less than the |
| * number of lines from the start of NBR. |
| */ |
| # define TV_VBURST_END_F2_MASK 0x000000ff |
| # define TV_VBURST_END_F2_SHIFT 0 |
| |
| #define TV_V_CTL_6 0x68050 |
| /** |
| * Offset to start of vertical colorburst, measured in one less than the |
| * number of lines from vertical start. |
| */ |
| # define TV_VBURST_START_F3_MASK 0x003f0000 |
| # define TV_VBURST_START_F3_SHIFT 16 |
| /** |
| * Offset to the end of vertical colorburst, measured in one less than the |
| * number of lines from the start of NBR. |
| */ |
| # define TV_VBURST_END_F3_MASK 0x000000ff |
| # define TV_VBURST_END_F3_SHIFT 0 |
| |
| #define TV_V_CTL_7 0x68054 |
| /** |
| * Offset to start of vertical colorburst, measured in one less than the |
| * number of lines from vertical start. |
| */ |
| # define TV_VBURST_START_F4_MASK 0x003f0000 |
| # define TV_VBURST_START_F4_SHIFT 16 |
| /** |
| * Offset to the end of vertical colorburst, measured in one less than the |
| * number of lines from the start of NBR. |
| */ |
| # define TV_VBURST_END_F4_MASK 0x000000ff |
| # define TV_VBURST_END_F4_SHIFT 0 |
| |
| #define TV_SC_CTL_1 0x68060 |
| /** Turns on the first subcarrier phase generation DDA */ |
| # define TV_SC_DDA1_EN (1 << 31) |
| /** Turns on the first subcarrier phase generation DDA */ |
| # define TV_SC_DDA2_EN (1 << 30) |
| /** Turns on the first subcarrier phase generation DDA */ |
| # define TV_SC_DDA3_EN (1 << 29) |
| /** Sets the subcarrier DDA to reset frequency every other field */ |
| # define TV_SC_RESET_EVERY_2 (0 << 24) |
| /** Sets the subcarrier DDA to reset frequency every fourth field */ |
| # define TV_SC_RESET_EVERY_4 (1 << 24) |
| /** Sets the subcarrier DDA to reset frequency every eighth field */ |
| # define TV_SC_RESET_EVERY_8 (2 << 24) |
| /** Sets the subcarrier DDA to never reset the frequency */ |
| # define TV_SC_RESET_NEVER (3 << 24) |
| /** Sets the peak amplitude of the colorburst.*/ |
| # define TV_BURST_LEVEL_MASK 0x00ff0000 |
| # define TV_BURST_LEVEL_SHIFT 16 |
| /** Sets the increment of the first subcarrier phase generation DDA */ |
| # define TV_SCDDA1_INC_MASK 0x00000fff |
| # define TV_SCDDA1_INC_SHIFT 0 |
| |
| #define TV_SC_CTL_2 0x68064 |
| /** Sets the rollover for the second subcarrier phase generation DDA */ |
| # define TV_SCDDA2_SIZE_MASK 0x7fff0000 |
| # define TV_SCDDA2_SIZE_SHIFT 16 |
| /** Sets the increent of the second subcarrier phase generation DDA */ |
| # define TV_SCDDA2_INC_MASK 0x00007fff |
| # define TV_SCDDA2_INC_SHIFT 0 |
| |
| #define TV_SC_CTL_3 0x68068 |
| /** Sets the rollover for the third subcarrier phase generation DDA */ |
| # define TV_SCDDA3_SIZE_MASK 0x7fff0000 |
| # define TV_SCDDA3_SIZE_SHIFT 16 |
| /** Sets the increent of the third subcarrier phase generation DDA */ |
| # define TV_SCDDA3_INC_MASK 0x00007fff |
| # define TV_SCDDA3_INC_SHIFT 0 |
| |
| #define TV_WIN_POS 0x68070 |
| /** X coordinate of the display from the start of horizontal active */ |
| # define TV_XPOS_MASK 0x1fff0000 |
| # define TV_XPOS_SHIFT 16 |
| /** Y coordinate of the display from the start of vertical active (NBR) */ |
| # define TV_YPOS_MASK 0x00000fff |
| # define TV_YPOS_SHIFT 0 |
| |
| #define TV_WIN_SIZE 0x68074 |
| /** Horizontal size of the display window, measured in pixels*/ |
| # define TV_XSIZE_MASK 0x1fff0000 |
| # define TV_XSIZE_SHIFT 16 |
| /** |
| * Vertical size of the display window, measured in pixels. |
| * |
| * Must be even for interlaced modes. |
| */ |
| # define TV_YSIZE_MASK 0x00000fff |
| # define TV_YSIZE_SHIFT 0 |
| |
| #define TV_FILTER_CTL_1 0x68080 |
| /** |
| * Enables automatic scaling calculation. |
| * |
| * If set, the rest of the registers are ignored, and the calculated values can |
| * be read back from the register. |
| */ |
| # define TV_AUTO_SCALE (1 << 31) |
| /** |
| * Disables the vertical filter. |
| * |
| * This is required on modes more than 1024 pixels wide */ |
| # define TV_V_FILTER_BYPASS (1 << 29) |
| /** Enables adaptive vertical filtering */ |
| # define TV_VADAPT (1 << 28) |
| # define TV_VADAPT_MODE_MASK (3 << 26) |
| /** Selects the least adaptive vertical filtering mode */ |
| # define TV_VADAPT_MODE_LEAST (0 << 26) |
| /** Selects the moderately adaptive vertical filtering mode */ |
| # define TV_VADAPT_MODE_MODERATE (1 << 26) |
| /** Selects the most adaptive vertical filtering mode */ |
| # define TV_VADAPT_MODE_MOST (3 << 26) |
| /** |
| * Sets the horizontal scaling factor. |
| * |
| * This should be the fractional part of the horizontal scaling factor divided |
| * by the oversampling rate. TV_HSCALE should be less than 1, and set to: |
| * |
| * (src width - 1) / ((oversample * dest width) - 1) |
| */ |
| # define TV_HSCALE_FRAC_MASK 0x00003fff |
| # define TV_HSCALE_FRAC_SHIFT 0 |
| |
| #define TV_FILTER_CTL_2 0x68084 |
| /** |
| * Sets the integer part of the 3.15 fixed-point vertical scaling factor. |
| * |
| * TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1) |
| */ |
| # define TV_VSCALE_INT_MASK 0x00038000 |
| # define TV_VSCALE_INT_SHIFT 15 |
| /** |
| * Sets the fractional part of the 3.15 fixed-point vertical scaling factor. |
| * |
| * \sa TV_VSCALE_INT_MASK |
| */ |
| # define TV_VSCALE_FRAC_MASK 0x00007fff |
| # define TV_VSCALE_FRAC_SHIFT 0 |
| |
| #define TV_FILTER_CTL_3 0x68088 |
| /** |
| * Sets the integer part of the 3.15 fixed-point vertical scaling factor. |
| * |
| * TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1)) |
| * |
| * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes. |
| */ |
| # define TV_VSCALE_IP_INT_MASK 0x00038000 |
| # define TV_VSCALE_IP_INT_SHIFT 15 |
| /** |
| * Sets the fractional part of the 3.15 fixed-point vertical scaling factor. |
| * |
| * For progressive modes, TV_VSCALE_IP_INT should be set to zeroes. |
| * |
| * \sa TV_VSCALE_IP_INT_MASK |
| */ |
| # define TV_VSCALE_IP_FRAC_MASK 0x00007fff |
| # define TV_VSCALE_IP_FRAC_SHIFT 0 |
| |
| #define TV_CC_CONTROL 0x68090 |
| # define TV_CC_ENABLE (1 << 31) |
| /** |
| * Specifies which field to send the CC data in. |
| * |
| * CC data is usually sent in field 0. |
| */ |
| # define TV_CC_FID_MASK (1 << 27) |
| # define TV_CC_FID_SHIFT 27 |
| /** Sets the horizontal position of the CC data. Usually 135. */ |
| # define TV_CC_HOFF_MASK 0x03ff0000 |
| # define TV_CC_HOFF_SHIFT 16 |
| /** Sets the vertical position of the CC data. Usually 21 */ |
| # define TV_CC_LINE_MASK 0x0000003f |
| # define TV_CC_LINE_SHIFT 0 |
| |
| #define TV_CC_DATA 0x68094 |
| # define TV_CC_RDY (1 << 31) |
| /** Second word of CC data to be transmitted. */ |
| # define TV_CC_DATA_2_MASK 0x007f0000 |
| # define TV_CC_DATA_2_SHIFT 16 |
| /** First word of CC data to be transmitted. */ |
| # define TV_CC_DATA_1_MASK 0x0000007f |
| # define TV_CC_DATA_1_SHIFT 0 |
| |
| #define TV_H_LUMA_0 0x68100 |
| #define TV_H_LUMA_59 0x681ec |
| #define TV_H_CHROMA_0 0x68200 |
| #define TV_H_CHROMA_59 0x682ec |
| #define TV_V_LUMA_0 0x68300 |
| #define TV_V_LUMA_42 0x683a8 |
| #define TV_V_CHROMA_0 0x68400 |
| #define TV_V_CHROMA_42 0x684a8 |
| |
| /* Display Port */ |
| #define DP_A 0x64000 /* eDP */ |
| #define DP_B 0x64100 |
| #define DP_C 0x64200 |
| #define DP_D 0x64300 |
| |
| #define DP_PORT_EN (1 << 31) |
| #define DP_PIPEB_SELECT (1 << 30) |
| #define DP_PIPE_MASK (1 << 30) |
| |
| /* Link training mode - select a suitable mode for each stage */ |
| #define DP_LINK_TRAIN_PAT_1 (0 << 28) |
| #define DP_LINK_TRAIN_PAT_2 (1 << 28) |
| #define DP_LINK_TRAIN_PAT_IDLE (2 << 28) |
| #define DP_LINK_TRAIN_OFF (3 << 28) |
| #define DP_LINK_TRAIN_MASK (3 << 28) |
| #define DP_LINK_TRAIN_SHIFT 28 |
| |
| /* CPT Link training mode */ |
| #define DP_LINK_TRAIN_PAT_1_CPT (0 << 8) |
| #define DP_LINK_TRAIN_PAT_2_CPT (1 << 8) |
| #define DP_LINK_TRAIN_PAT_IDLE_CPT (2 << 8) |
| #define DP_LINK_TRAIN_OFF_CPT (3 << 8) |
| #define DP_LINK_TRAIN_MASK_CPT (7 << 8) |
| #define DP_LINK_TRAIN_SHIFT_CPT 8 |
| |
| /* Signal voltages. These are mostly controlled by the other end */ |
| #define DP_VOLTAGE_0_4 (0 << 25) |
| #define DP_VOLTAGE_0_6 (1 << 25) |
| #define DP_VOLTAGE_0_8 (2 << 25) |
| #define DP_VOLTAGE_1_2 (3 << 25) |
| #define DP_VOLTAGE_MASK (7 << 25) |
| #define DP_VOLTAGE_SHIFT 25 |
| |
| /* Signal pre-emphasis levels, like voltages, the other end tells us what |
| * they want |
| */ |
| #define DP_PRE_EMPHASIS_0 (0 << 22) |
| #define DP_PRE_EMPHASIS_3_5 (1 << 22) |
| #define DP_PRE_EMPHASIS_6 (2 << 22) |
| #define DP_PRE_EMPHASIS_9_5 (3 << 22) |
| #define DP_PRE_EMPHASIS_MASK (7 << 22) |
| #define DP_PRE_EMPHASIS_SHIFT 22 |
| |
| /* How many wires to use. I guess 3 was too hard */ |
| #define DP_PORT_WIDTH_1 (0 << 19) |
| #define DP_PORT_WIDTH_2 (1 << 19) |
| #define DP_PORT_WIDTH_4 (3 << 19) |
| #define DP_PORT_WIDTH_MASK (7 << 19) |
| |
| /* Mystic DPCD version 1.1 special mode */ |
| #define DP_ENHANCED_FRAMING (1 << 18) |
| |
| /* eDP */ |
| #define DP_PLL_FREQ_270MHZ (0 << 16) |
| #define DP_PLL_FREQ_160MHZ (1 << 16) |
| #define DP_PLL_FREQ_MASK (3 << 16) |
| |
| /** locked once port is enabled */ |
| #define DP_PORT_REVERSAL (1 << 15) |
| |
| /* eDP */ |
| #define DP_PLL_ENABLE (1 << 14) |
| |
| /** sends the clock on lane 15 of the PEG for debug */ |
| #define DP_CLOCK_OUTPUT_ENABLE (1 << 13) |
| |
| #define DP_SCRAMBLING_DISABLE (1 << 12) |
| #define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7) |
| |
| /** limit RGB values to avoid confusing TVs */ |
| #define DP_COLOR_RANGE_16_235 (1 << 8) |
| |
| /** Turn on the audio link */ |
| #define DP_AUDIO_OUTPUT_ENABLE (1 << 6) |
| |
| /** vs and hs sync polarity */ |
| #define DP_SYNC_VS_HIGH (1 << 4) |
| #define DP_SYNC_HS_HIGH (1 << 3) |
| |
| /** A fantasy */ |
| #define DP_DETECTED (1 << 2) |
| |
| /** The aux channel provides a way to talk to the |
| * signal sink for DDC etc. Max packet size supported |
| * is 20 bytes in each direction, hence the 5 fixed |
| * data registers |
| */ |
| #define DPA_AUX_CH_CTL 0x64010 |
| #define DPA_AUX_CH_DATA1 0x64014 |
| #define DPA_AUX_CH_DATA2 0x64018 |
| #define DPA_AUX_CH_DATA3 0x6401c |
| #define DPA_AUX_CH_DATA4 0x64020 |
| #define DPA_AUX_CH_DATA5 0x64024 |
| |
| #define DPB_AUX_CH_CTL 0x64110 |
| #define DPB_AUX_CH_DATA1 0x64114 |
| #define DPB_AUX_CH_DATA2 0x64118 |
| #define DPB_AUX_CH_DATA3 0x6411c |
| #define DPB_AUX_CH_DATA4 0x64120 |
| #define DPB_AUX_CH_DATA5 0x64124 |
| |
| #define DPC_AUX_CH_CTL 0x64210 |
| #define DPC_AUX_CH_DATA1 0x64214 |
| #define DPC_AUX_CH_DATA2 0x64218 |
| #define DPC_AUX_CH_DATA3 0x6421c |
| #define DPC_AUX_CH_DATA4 0x64220 |
| #define DPC_AUX_CH_DATA5 0x64224 |
| |
| #define DPD_AUX_CH_CTL 0x64310 |
| #define DPD_AUX_CH_DATA1 0x64314 |
| #define DPD_AUX_CH_DATA2 0x64318 |
| #define DPD_AUX_CH_DATA3 0x6431c |
| #define DPD_AUX_CH_DATA4 0x64320 |
| #define DPD_AUX_CH_DATA5 0x64324 |
| |
| #define DP_AUX_CH_CTL_SEND_BUSY (1 << 31) |
| #define DP_AUX_CH_CTL_DONE (1 << 30) |
| #define DP_AUX_CH_CTL_INTERRUPT (1 << 29) |
| #define DP_AUX_CH_CTL_TIME_OUT_ERROR (1 << 28) |
| #define DP_AUX_CH_CTL_TIME_OUT_400us (0 << 26) |
| #define DP_AUX_CH_CTL_TIME_OUT_600us (1 << 26) |
| #define DP_AUX_CH_CTL_TIME_OUT_800us (2 << 26) |
| #define DP_AUX_CH_CTL_TIME_OUT_1600us (3 << 26) |
| #define DP_AUX_CH_CTL_TIME_OUT_MASK (3 << 26) |
| #define DP_AUX_CH_CTL_RECEIVE_ERROR (1 << 25) |
| #define DP_AUX_CH_CTL_MESSAGE_SIZE_MASK (0x1f << 20) |
| #define DP_AUX_CH_CTL_MESSAGE_SIZE_SHIFT 20 |
| #define DP_AUX_CH_CTL_PRECHARGE_2US_MASK (0xf << 16) |
| #define DP_AUX_CH_CTL_PRECHARGE_2US_SHIFT 16 |
| #define DP_AUX_CH_CTL_AUX_AKSV_SELECT (1 << 15) |
| #define DP_AUX_CH_CTL_MANCHESTER_TEST (1 << 14) |
| #define DP_AUX_CH_CTL_SYNC_TEST (1 << 13) |
| #define DP_AUX_CH_CTL_DEGLITCH_TEST (1 << 12) |
| #define DP_AUX_CH_CTL_PRECHARGE_TEST (1 << 11) |
| #define DP_AUX_CH_CTL_BIT_CLOCK_2X_MASK (0x7ff) |
| #define DP_AUX_CH_CTL_BIT_CLOCK_2X_SHIFT 0 |
| |
| /* |
| * Computing GMCH M and N values for the Display Port link |
| * |
| * GMCH M/N = dot clock * bytes per pixel / ls_clk * # of lanes |
| * |
| * ls_clk (we assume) is the DP link clock (1.62 or 2.7 GHz) |
| * |
| * The GMCH value is used internally |
| * |
| * bytes_per_pixel is the number of bytes coming out of the plane, |
| * which is after the LUTs, so we want the bytes for our color format. |
| * For our current usage, this is always 3, one byte for R, G and B. |
| */ |
| #define _PIPEA_GMCH_DATA_M 0x70050 |
| #define _PIPEB_GMCH_DATA_M 0x71050 |
| |
| /* Transfer unit size for display port - 1, default is 0x3f (for TU size 64) */ |
| #define PIPE_GMCH_DATA_M_TU_SIZE_MASK (0x3f << 25) |
| #define PIPE_GMCH_DATA_M_TU_SIZE_SHIFT 25 |
| |
| #define PIPE_GMCH_DATA_M_MASK (0xffffff) |
| |
| #define _PIPEA_GMCH_DATA_N 0x70054 |
| #define _PIPEB_GMCH_DATA_N 0x71054 |
| #define PIPE_GMCH_DATA_N_MASK (0xffffff) |
| |
| /* |
| * Computing Link M and N values for the Display Port link |
| * |
| * Link M / N = pixel_clock / ls_clk |
| * |
| * (the DP spec calls pixel_clock the 'strm_clk') |
| * |
| * The Link value is transmitted in the Main Stream |
| * Attributes and VB-ID. |
| */ |
| |
| #define _PIPEA_DP_LINK_M 0x70060 |
| #define _PIPEB_DP_LINK_M 0x71060 |
| #define PIPEA_DP_LINK_M_MASK (0xffffff) |
| |
| #define _PIPEA_DP_LINK_N 0x70064 |
| #define _PIPEB_DP_LINK_N 0x71064 |
| #define PIPEA_DP_LINK_N_MASK (0xffffff) |
| |
| #define PIPE_GMCH_DATA_M(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_M, _PIPEB_GMCH_DATA_M) |
| #define PIPE_GMCH_DATA_N(pipe) _PIPE(pipe, _PIPEA_GMCH_DATA_N, _PIPEB_GMCH_DATA_N) |
| #define PIPE_DP_LINK_M(pipe) _PIPE(pipe, _PIPEA_DP_LINK_M, _PIPEB_DP_LINK_M) |
| #define PIPE_DP_LINK_N(pipe) _PIPE(pipe, _PIPEA_DP_LINK_N, _PIPEB_DP_LINK_N) |
| |
| /* Display & cursor control */ |
| |
| /* Pipe A */ |
| #define _PIPEADSL 0x70000 |
| #define DSL_LINEMASK_GEN2 0x00000fff |
| #define DSL_LINEMASK_GEN3 0x00001fff |
| #define _PIPEACONF 0x70008 |
| #define PIPECONF_ENABLE (1<<31) |
| #define PIPECONF_DISABLE 0 |
| #define PIPECONF_DOUBLE_WIDE (1<<30) |
| #define I965_PIPECONF_ACTIVE (1<<30) |
| #define PIPECONF_FRAME_START_DELAY_MASK (3<<27) |
| #define PIPECONF_SINGLE_WIDE 0 |
| #define PIPECONF_PIPE_UNLOCKED 0 |
| #define PIPECONF_PIPE_LOCKED (1<<25) |
| #define PIPECONF_PALETTE 0 |
| #define PIPECONF_GAMMA (1<<24) |
| #define PIPECONF_FORCE_BORDER (1<<25) |
| #define PIPECONF_INTERLACE_MASK (7 << 21) |
| /* Note that pre-gen3 does not support interlaced display directly. Panel |
| * fitting must be disabled on pre-ilk for interlaced. */ |
| #define PIPECONF_PROGRESSIVE (0 << 21) |
| #define PIPECONF_INTERLACE_W_SYNC_SHIFT_PANEL (4 << 21) /* gen4 only */ |
| #define PIPECONF_INTERLACE_W_SYNC_SHIFT (5 << 21) /* gen4 only */ |
| #define PIPECONF_INTERLACE_W_FIELD_INDICATION (6 << 21) |
| #define PIPECONF_INTERLACE_FIELD_0_ONLY (7 << 21) /* gen3 only */ |
| /* Ironlake and later have a complete new set of values for interlaced. PFIT |
| * means panel fitter required, PF means progressive fetch, DBL means power |
| * saving pixel doubling. */ |
| #define PIPECONF_PFIT_PF_INTERLACED_ILK (1 << 21) |
| #define PIPECONF_INTERLACED_ILK (3 << 21) |
| #define PIPECONF_INTERLACED_DBL_ILK (4 << 21) /* ilk/snb only */ |
| #define PIPECONF_PFIT_PF_INTERLACED_DBL_ILK (5 << 21) /* ilk/snb only */ |
| #define PIPECONF_CXSR_DOWNCLOCK (1<<16) |
| #define PIPECONF_BPP_MASK (0x000000e0) |
| #define PIPECONF_BPP_8 (0<<5) |
| #define PIPECONF_BPP_10 (1<<5) |
| #define PIPECONF_BPP_6 (2<<5) |
| #define PIPECONF_BPP_12 (3<<5) |
| #define PIPECONF_DITHER_EN (1<<4) |
| #define PIPECONF_DITHER_TYPE_MASK (0x0000000c) |
| #define PIPECONF_DITHER_TYPE_SP (0<<2) |
| #define PIPECONF_DITHER_TYPE_ST1 (1<<2) |
| #define PIPECONF_DITHER_TYPE_ST2 (2<<2) |
| #define PIPECONF_DITHER_TYPE_TEMP (3<<2) |
| #define _PIPEASTAT 0x70024 |
| #define PIPE_FIFO_UNDERRUN_STATUS (1UL<<31) |
| #define SPRITE1_FLIPDONE_INT_EN_VLV (1UL<<30) |
| #define PIPE_CRC_ERROR_ENABLE (1UL<<29) |
| #define PIPE_CRC_DONE_ENABLE (1UL<<28) |
| #define PIPE_GMBUS_EVENT_ENABLE (1UL<<27) |
| #define PLANE_FLIP_DONE_INT_EN_VLV (1UL<<26) |
| #define PIPE_HOTPLUG_INTERRUPT_ENABLE (1UL<<26) |
| #define PIPE_VSYNC_INTERRUPT_ENABLE (1UL<<25) |
| #define PIPE_DISPLAY_LINE_COMPARE_ENABLE (1UL<<24) |
| #define PIPE_DPST_EVENT_ENABLE (1UL<<23) |
| #define SPRITE0_FLIP_DONE_INT_EN_VLV (1UL<<26) |
| #define PIPE_LEGACY_BLC_EVENT_ENABLE (1UL<<22) |
| #define PIPE_ODD_FIELD_INTERRUPT_ENABLE (1UL<<21) |
| #define PIPE_EVEN_FIELD_INTERRUPT_ENABLE (1UL<<20) |
| #define PIPE_HOTPLUG_TV_INTERRUPT_ENABLE (1UL<<18) /* pre-965 */ |
| #define PIPE_START_VBLANK_INTERRUPT_ENABLE (1UL<<18) /* 965 or later */ |
| #define PIPE_VBLANK_INTERRUPT_ENABLE (1UL<<17) |
| #define PIPEA_HBLANK_INT_EN_VLV (1UL<<16) |
| #define PIPE_OVERLAY_UPDATED_ENABLE (1UL<<16) |
| #define SPRITE1_FLIPDONE_INT_STATUS_VLV (1UL<<15) |
| #define SPRITE0_FLIPDONE_INT_STATUS_VLV (1UL<<15) |
| #define PIPE_CRC_ERROR_INTERRUPT_STATUS (1UL<<13) |
| #define PIPE_CRC_DONE_INTERRUPT_STATUS (1UL<<12) |
| #define PIPE_GMBUS_INTERRUPT_STATUS (1UL<<11) |
| #define PLANE_FLIPDONE_INT_STATUS_VLV (1UL<<10) |
| #define PIPE_HOTPLUG_INTERRUPT_STATUS (1UL<<10) |
| #define PIPE_VSYNC_INTERRUPT_STATUS (1UL<<9) |
| #define PIPE_DISPLAY_LINE_COMPARE_STATUS (1UL<<8) |
| #define PIPE_DPST_EVENT_STATUS (1UL<<7) |
| #define PIPE_LEGACY_BLC_EVENT_STATUS (1UL<<6) |
| #define PIPE_ODD_FIELD_INTERRUPT_STATUS (1UL<<5) |
| #define PIPE_EVEN_FIELD_INTERRUPT_STATUS (1UL<<4) |
| #define PIPE_HOTPLUG_TV_INTERRUPT_STATUS (1UL<<2) /* pre-965 */ |
| #define PIPE_START_VBLANK_INTERRUPT_STATUS (1UL<<2) /* 965 or later */ |
| #define PIPE_VBLANK_INTERRUPT_STATUS (1UL<<1) |
| #define PIPE_OVERLAY_UPDATED_STATUS (1UL<<0) |
| #define PIPE_BPC_MASK (7 << 5) /* Ironlake */ |
| #define PIPE_8BPC (0 << 5) |
| #define PIPE_10BPC (1 << 5) |
| #define PIPE_6BPC (2 << 5) |
| #define PIPE_12BPC (3 << 5) |
| |
| #define PIPESRC(pipe) _PIPE(pipe, _PIPEASRC, _PIPEBSRC) |
| #define PIPECONF(pipe) _PIPE(pipe, _PIPEACONF, _PIPEBCONF) |
| #define PIPEDSL(pipe) _PIPE(pipe, _PIPEADSL, _PIPEBDSL) |
| #define PIPEFRAME(pipe) _PIPE(pipe, _PIPEAFRAMEHIGH, _PIPEBFRAMEHIGH) |
| #define PIPEFRAMEPIXEL(pipe) _PIPE(pipe, _PIPEAFRAMEPIXEL, _PIPEBFRAMEPIXEL) |
| #define PIPESTAT(pipe) _PIPE(pipe, _PIPEASTAT, _PIPEBSTAT) |
| |
| #define VLV_DPFLIPSTAT 0x70028 |
| #define PIPEB_LINE_COMPARE_INT_EN (1<<29) |
| #define PIPEB_HLINE_INT_EN (1<<28) |
| #define PIPEB_VBLANK_INT_EN (1<<27) |
| #define SPRITED_FLIPDONE_INT_EN (1<<26) |
| #define SPRITEC_FLIPDONE_INT_EN (1<<25) |
| #define PLANEB_FLIPDONE_INT_EN (1<<24) |
| #define PIPEA_LINE_COMPARE_INT_EN (1<<21) |
| #define PIPEA_HLINE_INT_EN (1<<20) |
| #define PIPEA_VBLANK_INT_EN (1<<19) |
| #define SPRITEB_FLIPDONE_INT_EN (1<<18) |
| #define SPRITEA_FLIPDONE_INT_EN (1<<17) |
| #define PLANEA_FLIPDONE_INT_EN (1<<16) |
| |
| #define DPINVGTT 0x7002c /* VLV only */ |
| #define CURSORB_INVALID_GTT_INT_EN (1<<23) |
| #define CURSORA_INVALID_GTT_INT_EN (1<<22) |
| #define SPRITED_INVALID_GTT_INT_EN (1<<21) |
| #define SPRITEC_INVALID_GTT_INT_EN (1<<20) |
| #define PLANEB_INVALID_GTT_INT_EN (1<<19) |
| #define SPRITEB_INVALID_GTT_INT_EN (1<<18) |
| #define SPRITEA_INVALID_GTT_INT_EN (1<<17) |
| #define PLANEA_INVALID_GTT_INT_EN (1<<16) |
| #define DPINVGTT_EN_MASK 0xff0000 |
| #define CURSORB_INVALID_GTT_STATUS (1<<7) |
| #define CURSORA_INVALID_GTT_STATUS (1<<6) |
| #define SPRITED_INVALID_GTT_STATUS (1<<5) |
| #define SPRITEC_INVALID_GTT_STATUS (1<<4) |
| #define PLANEB_INVALID_GTT_STATUS (1<<3) |
| #define SPRITEB_INVALID_GTT_STATUS (1<<2) |
| #define SPRITEA_INVALID_GTT_STATUS (1<<1) |
| #define PLANEA_INVALID_GTT_STATUS (1<<0) |
| #define DPINVGTT_STATUS_MASK 0xff |
| |
| #define DSPARB 0x70030 |
| #define DSPARB_CSTART_MASK (0x7f << 7) |
| #define DSPARB_CSTART_SHIFT 7 |
| #define DSPARB_BSTART_MASK (0x7f) |
| #define DSPARB_BSTART_SHIFT 0 |
| #define DSPARB_BEND_SHIFT 9 /* on 855 */ |
| #define DSPARB_AEND_SHIFT 0 |
| |
| #define DSPFW1 0x70034 |
| #define DSPFW_SR_SHIFT 23 |
| #define DSPFW_SR_MASK (0x1ff<<23) |
| #define DSPFW_CURSORB_SHIFT 16 |
| #define DSPFW_CURSORB_MASK (0x3f<<16) |
| #define DSPFW_PLANEB_SHIFT 8 |
| #define DSPFW_PLANEB_MASK (0x7f<<8) |
| #define DSPFW_PLANEA_MASK (0x7f) |
| #define DSPFW2 0x70038 |
| #define DSPFW_CURSORA_MASK 0x00003f00 |
| #define DSPFW_CURSORA_SHIFT 8 |
| #define DSPFW_PLANEC_MASK (0x7f) |
| #define DSPFW3 0x7003c |
| #define DSPFW_HPLL_SR_EN (1<<31) |
| #define DSPFW_CURSOR_SR_SHIFT 24 |
| #define PINEVIEW_SELF_REFRESH_EN (1<<30) |
| #define DSPFW_CURSOR_SR_MASK (0x3f<<24) |
| #define DSPFW_HPLL_CURSOR_SHIFT 16 |
| #define DSPFW_HPLL_CURSOR_MASK (0x3f<<16) |
| #define DSPFW_HPLL_SR_MASK (0x1ff) |
| |
| /* drain latency register values*/ |
| #define DRAIN_LATENCY_PRECISION_32 32 |
| #define DRAIN_LATENCY_PRECISION_16 16 |
| #define VLV_DDL1 0x70050 |
| #define DDL_CURSORA_PRECISION_32 (1<<31) |
| #define DDL_CURSORA_PRECISION_16 (0<<31) |
| #define DDL_CURSORA_SHIFT 24 |
| #define DDL_PLANEA_PRECISION_32 (1<<7) |
| #define DDL_PLANEA_PRECISION_16 (0<<7) |
| #define VLV_DDL2 0x70054 |
| #define DDL_CURSORB_PRECISION_32 (1<<31) |
| #define DDL_CURSORB_PRECISION_16 (0<<31) |
| #define DDL_CURSORB_SHIFT 24 |
| #define DDL_PLANEB_PRECISION_32 (1<<7) |
| #define DDL_PLANEB_PRECISION_16 (0<<7) |
| |
| /* FIFO watermark sizes etc */ |
| #define G4X_FIFO_LINE_SIZE 64 |
| #define I915_FIFO_LINE_SIZE 64 |
| #define I830_FIFO_LINE_SIZE 32 |
| |
| #define VALLEYVIEW_FIFO_SIZE 255 |
| #define G4X_FIFO_SIZE 127 |
| #define I965_FIFO_SIZE 512 |
| #define I945_FIFO_SIZE 127 |
| #define I915_FIFO_SIZE 95 |
| #define I855GM_FIFO_SIZE 127 /* In cachelines */ |
| #define I830_FIFO_SIZE 95 |
| |
| #define VALLEYVIEW_MAX_WM 0xff |
| #define G4X_MAX_WM 0x3f |
| #define I915_MAX_WM 0x3f |
| |
| #define PINEVIEW_DISPLAY_FIFO 512 /* in 64byte unit */ |
| #define PINEVIEW_FIFO_LINE_SIZE 64 |
| #define PINEVIEW_MAX_WM 0x1ff |
| #define PINEVIEW_DFT_WM 0x3f |
| #define PINEVIEW_DFT_HPLLOFF_WM 0 |
| #define PINEVIEW_GUARD_WM 10 |
| #define PINEVIEW_CURSOR_FIFO 64 |
| #define PINEVIEW_CURSOR_MAX_WM 0x3f |
| #define PINEVIEW_CURSOR_DFT_WM 0 |
| #define PINEVIEW_CURSOR_GUARD_WM 5 |
| |
| #define VALLEYVIEW_CURSOR_MAX_WM 64 |
| #define I965_CURSOR_FIFO 64 |
| #define I965_CURSOR_MAX_WM 32 |
| #define I965_CURSOR_DFT_WM 8 |
| |
| /* define the Watermark register on Ironlake */ |
| #define WM0_PIPEA_ILK 0x45100 |
| #define WM0_PIPE_PLANE_MASK (0x7f<<16) |
| #define WM0_PIPE_PLANE_SHIFT 16 |
| #define WM0_PIPE_SPRITE_MASK (0x3f<<8) |
| #define WM0_PIPE_SPRITE_SHIFT 8 |
| #define WM0_PIPE_CURSOR_MASK (0x1f) |
| |
| #define WM0_PIPEB_ILK 0x45104 |
| #define WM0_PIPEC_IVB 0x45200 |
| #define WM1_LP_ILK 0x45108 |
| #define WM1_LP_SR_EN (1<<31) |
| #define WM1_LP_LATENCY_SHIFT 24 |
| #define WM1_LP_LATENCY_MASK (0x7f<<24) |
| #define WM1_LP_FBC_MASK (0xf<<20) |
| #define WM1_LP_FBC_SHIFT 20 |
| #define WM1_LP_SR_MASK (0x1ff<<8) |
| #define WM1_LP_SR_SHIFT 8 |
| #define WM1_LP_CURSOR_MASK (0x3f) |
| #define WM2_LP_ILK 0x4510c |
| #define WM2_LP_EN (1<<31) |
| #define WM3_LP_ILK 0x45110 |
| #define WM3_LP_EN (1<<31) |
| #define WM1S_LP_ILK 0x45120 |
| #define WM2S_LP_IVB 0x45124 |
| #define WM3S_LP_IVB 0x45128 |
| #define WM1S_LP_EN (1<<31) |
| |
| /* Memory latency timer register */ |
| #define MLTR_ILK 0x11222 |
| #define MLTR_WM1_SHIFT 0 |
| #define MLTR_WM2_SHIFT 8 |
| /* the unit of memory self-refresh latency time is 0.5us */ |
| #define ILK_SRLT_MASK 0x3f |
| #define ILK_LATENCY(shift) (I915_READ(MLTR_ILK) >> (shift) & ILK_SRLT_MASK) |
| #define ILK_READ_WM1_LATENCY() ILK_LATENCY(MLTR_WM1_SHIFT) |
| #define ILK_READ_WM2_LATENCY() ILK_LATENCY(MLTR_WM2_SHIFT) |
| |
| /* define the fifo size on Ironlake */ |
| #define ILK_DISPLAY_FIFO 128 |
| #define ILK_DISPLAY_MAXWM 64 |
| #define ILK_DISPLAY_DFTWM 8 |
| #define ILK_CURSOR_FIFO 32 |
| #define ILK_CURSOR_MAXWM 16 |
| #define ILK_CURSOR_DFTWM 8 |
| |
| #define ILK_DISPLAY_SR_FIFO 512 |
| #define ILK_DISPLAY_MAX_SRWM 0x1ff |
| #define ILK_DISPLAY_DFT_SRWM 0x3f |
| #define ILK_CURSOR_SR_FIFO 64 |
| #define ILK_CURSOR_MAX_SRWM 0x3f |
| #define ILK_CURSOR_DFT_SRWM 8 |
| |
| #define ILK_FIFO_LINE_SIZE 64 |
| |
| /* define the WM info on Sandybridge */ |
| #define SNB_DISPLAY_FIFO 128 |
| #define SNB_DISPLAY_MAXWM 0x7f /* bit 16:22 */ |
| #define SNB_DISPLAY_DFTWM 8 |
| #define SNB_CURSOR_FIFO 32 |
| #define SNB_CURSOR_MAXWM 0x1f /* bit 4:0 */ |
| #define SNB_CURSOR_DFTWM 8 |
| |
| #define SNB_DISPLAY_SR_FIFO 512 |
| #define SNB_DISPLAY_MAX_SRWM 0x1ff /* bit 16:8 */ |
| #define SNB_DISPLAY_DFT_SRWM 0x3f |
| #define SNB_CURSOR_SR_FIFO 64 |
| #define SNB_CURSOR_MAX_SRWM 0x3f /* bit 5:0 */ |
| #define SNB_CURSOR_DFT_SRWM 8 |
| |
| #define SNB_FBC_MAX_SRWM 0xf /* bit 23:20 */ |
| |
| #define SNB_FIFO_LINE_SIZE 64 |
| |
| |
| /* the address where we get all kinds of latency value */ |
| #define SSKPD 0x5d10 |
| #define SSKPD_WM_MASK 0x3f |
| #define SSKPD_WM0_SHIFT 0 |
| #define SSKPD_WM1_SHIFT 8 |
| #define SSKPD_WM2_SHIFT 16 |
| #define SSKPD_WM3_SHIFT 24 |
| |
| #define SNB_LATENCY(shift) (I915_READ(MCHBAR_MIRROR_BASE_SNB + SSKPD) >> (shift) & SSKPD_WM_MASK) |
| #define SNB_READ_WM0_LATENCY() SNB_LATENCY(SSKPD_WM0_SHIFT) |
| #define SNB_READ_WM1_LATENCY() SNB_LATENCY(SSKPD_WM1_SHIFT) |
| #define SNB_READ_WM2_LATENCY() SNB_LATENCY(SSKPD_WM2_SHIFT) |
| #define SNB_READ_WM3_LATENCY() SNB_LATENCY(SSKPD_WM3_SHIFT) |
| |
| /* |
| * The two pipe frame counter registers are not synchronized, so |
| * reading a stable value is somewhat tricky. The following code |
| * should work: |
| * |
| * do { |
| * high1 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >> |
| * PIPE_FRAME_HIGH_SHIFT; |
| * low1 = ((INREG(PIPEAFRAMEPIXEL) & PIPE_FRAME_LOW_MASK) >> |
| * PIPE_FRAME_LOW_SHIFT); |
| * high2 = ((INREG(PIPEAFRAMEHIGH) & PIPE_FRAME_HIGH_MASK) >> |
| * PIPE_FRAME_HIGH_SHIFT); |
| * } while (high1 != high2); |
| * frame = (high1 << 8) | low1; |
| */ |
| #define _PIPEAFRAMEHIGH 0x70040 |
| #define PIPE_FRAME_HIGH_MASK 0x0000ffff |
| #define PIPE_FRAME_HIGH_SHIFT 0 |
| #define _PIPEAFRAMEPIXEL 0x70044 |
| #define PIPE_FRAME_LOW_MASK 0xff000000 |
| #define PIPE_FRAME_LOW_SHIFT 24 |
| #define PIPE_PIXEL_MASK 0x00ffffff |
| #define PIPE_PIXEL_SHIFT 0 |
| /* GM45+ just has to be different */ |
| #define _PIPEA_FRMCOUNT_GM45 0x70040 |
| #define _PIPEA_FLIPCOUNT_GM45 0x70044 |
| #define PIPE_FRMCOUNT_GM45(pipe) _PIPE(pipe, _PIPEA_FRMCOUNT_GM45, _PIPEB_FRMCOUNT_GM45) |
| |
| /* Cursor A & B regs */ |
| #define _CURACNTR 0x70080 |
| /* Old style CUR*CNTR flags (desktop 8xx) */ |
| #define CURSOR_ENABLE 0x80000000 |
| #define CURSOR_GAMMA_ENABLE 0x40000000 |
| #define CURSOR_STRIDE_MASK 0x30000000 |
| #define CURSOR_FORMAT_SHIFT 24 |
| #define CURSOR_FORMAT_MASK (0x07 << CURSOR_FORMAT_SHIFT) |
| #define CURSOR_FORMAT_2C (0x00 << CURSOR_FORMAT_SHIFT) |
| #define CURSOR_FORMAT_3C (0x01 << CURSOR_FORMAT_SHIFT) |
| #define CURSOR_FORMAT_4C (0x02 << CURSOR_FORMAT_SHIFT) |
| #define CURSOR_FORMAT_ARGB (0x04 << CURSOR_FORMAT_SHIFT) |
| #define CURSOR_FORMAT_XRGB (0x05 << CURSOR_FORMAT_SHIFT) |
| /* New style CUR*CNTR flags */ |
| #define CURSOR_MODE 0x27 |
| #define CURSOR_MODE_DISABLE 0x00 |
| #define CURSOR_MODE_64_32B_AX 0x07 |
| #define CURSOR_MODE_64_ARGB_AX ((1 << 5) | CURSOR_MODE_64_32B_AX) |
| #define MCURSOR_PIPE_SELECT (1 << 28) |
| #define MCURSOR_PIPE_A 0x00 |
| #define MCURSOR_PIPE_B (1 << 28) |
| #define MCURSOR_GAMMA_ENABLE (1 << 26) |
| #define _CURABASE 0x70084 |
| #define _CURAPOS 0x70088 |
| #define CURSOR_POS_MASK 0x007FF |
| #define CURSOR_POS_SIGN 0x8000 |
| #define CURSOR_X_SHIFT 0 |
| #define CURSOR_Y_SHIFT 16 |
| #define CURSIZE 0x700a0 |
| #define _CURBCNTR 0x700c0 |
| #define _CURBBASE 0x700c4 |
| #define _CURBPOS 0x700c8 |
| |
| #define _CURBCNTR_IVB 0x71080 |
| #define _CURBBASE_IVB 0x71084 |
| #define _CURBPOS_IVB 0x71088 |
| |
| #define CURCNTR(pipe) _PIPE(pipe, _CURACNTR, _CURBCNTR) |
| #define CURBASE(pipe) _PIPE(pipe, _CURABASE, _CURBBASE) |
| #define CURPOS(pipe) _PIPE(pipe, _CURAPOS, _CURBPOS) |
| |
| #define CURCNTR_IVB(pipe) _PIPE(pipe, _CURACNTR, _CURBCNTR_IVB) |
| #define CURBASE_IVB(pipe) _PIPE(pipe, _CURABASE, _CURBBASE_IVB) |
| #define CURPOS_IVB(pipe) _PIPE(pipe, _CURAPOS, _CURBPOS_IVB) |
| |
| /* Display A control */ |
| #define _DSPACNTR 0x70180 |
| #define DISPLAY_PLANE_ENABLE (1<<31) |
| #define DISPLAY_PLANE_DISABLE 0 |
| #define DISPPLANE_GAMMA_ENABLE (1<<30) |
| #define DISPPLANE_GAMMA_DISABLE 0 |
| #define DISPPLANE_PIXFORMAT_MASK (0xf<<26) |
| #define DISPPLANE_8BPP (0x2<<26) |
| #define DISPPLANE_15_16BPP (0x4<<26) |
| #define DISPPLANE_16BPP (0x5<<26) |
| #define DISPPLANE_32BPP_NO_ALPHA (0x6<<26) |
| #define DISPPLANE_32BPP (0x7<<26) |
| #define DISPPLANE_32BPP_30BIT_NO_ALPHA (0xa<<26) |
| #define DISPPLANE_STEREO_ENABLE (1<<25) |
| #define DISPPLANE_STEREO_DISABLE 0 |
| #define DISPPLANE_SEL_PIPE_SHIFT 24 |
| #define DISPPLANE_SEL_PIPE_MASK (3<<DISPPLANE_SEL_PIPE_SHIFT) |
| #define DISPPLANE_SEL_PIPE_A 0 |
| #define DISPPLANE_SEL_PIPE_B (1<<DISPPLANE_SEL_PIPE_SHIFT) |
| #define DISPPLANE_SRC_KEY_ENABLE (1<<22) |
| #define DISPPLANE_SRC_KEY_DISABLE 0 |
| #define DISPPLANE_LINE_DOUBLE (1<<20) |
| #define DISPPLANE_NO_LINE_DOUBLE 0 |
| #define DISPPLANE_STEREO_POLARITY_FIRST 0 |
| #define DISPPLANE_STEREO_POLARITY_SECOND (1<<18) |
| #define DISPPLANE_TRICKLE_FEED_DISABLE (1<<14) /* Ironlake */ |
| #define DISPPLANE_TILED (1<<10) |
| #define _DSPAADDR 0x70184 |
| #define _DSPASTRIDE 0x70188 |
| #define _DSPAPOS 0x7018C /* reserved */ |
| #define _DSPASIZE 0x70190 |
| #define _DSPASURF 0x7019C /* 965+ only */ |
| #define _DSPATILEOFF 0x701A4 /* 965+ only */ |
| |
| #define DSPCNTR(plane) _PIPE(plane, _DSPACNTR, _DSPBCNTR) |
| #define DSPADDR(plane) _PIPE(plane, _DSPAADDR, _DSPBADDR) |
| #define DSPSTRIDE(plane) _PIPE(plane, _DSPASTRIDE, _DSPBSTRIDE) |
| #define DSPPOS(plane) _PIPE(plane, _DSPAPOS, _DSPBPOS) |
| #define DSPSIZE(plane) _PIPE(plane, _DSPASIZE, _DSPBSIZE) |
| #define DSPSURF(plane) _PIPE(plane, _DSPASURF, _DSPBSURF) |
| #define DSPTILEOFF(plane) _PIPE(plane, _DSPATILEOFF, _DSPBTILEOFF) |
| #define DSPLINOFF(plane) DSPADDR(plane) |
| |
| /* Display/Sprite base address macros */ |
| #define DISP_BASEADDR_MASK (0xfffff000) |
| #define I915_LO_DISPBASE(val) (val & ~DISP_BASEADDR_MASK) |
| #define I915_HI_DISPBASE(val) (val & DISP_BASEADDR_MASK) |
| #define I915_MODIFY_DISPBASE(reg, gfx_addr) \ |
| (I915_WRITE((reg), (gfx_addr) | I915_LO_DISPBASE(I915_READ(reg)))) |
| |
| /* VBIOS flags */ |
| #define SWF00 0x71410 |
| #define SWF01 0x71414 |
| #define SWF02 0x71418 |
| #define SWF03 0x7141c |
| #define SWF04 0x71420 |
| #define SWF05 0x71424 |
| #define SWF06 0x71428 |
| #define SWF10 0x70410 |
| #define SWF11 0x70414 |
| #define SWF14 0x71420 |
| #define SWF30 0x72414 |
| #define SWF31 0x72418 |
| #define SWF32 0x7241c |
| |
| /* Pipe B */ |
| #define _PIPEBDSL 0x71000 |
| #define _PIPEBCONF 0x71008 |
| #define _PIPEBSTAT 0x71024 |
| #define _PIPEBFRAMEHIGH 0x71040 |
| #define _PIPEBFRAMEPIXEL 0x71044 |
| #define _PIPEB_FRMCOUNT_GM45 0x71040 |
| #define _PIPEB_FLIPCOUNT_GM45 0x71044 |
| |
| |
| /* Display B control */ |
| #define _DSPBCNTR 0x71180 |
| #define DISPPLANE_ALPHA_TRANS_ENABLE (1<<15) |
| #define DISPPLANE_ALPHA_TRANS_DISABLE 0 |
| #define DISPPLANE_SPRITE_ABOVE_DISPLAY 0 |
| #define DISPPLANE_SPRITE_ABOVE_OVERLAY (1) |
| #define _DSPBADDR 0x71184 |
| #define _DSPBSTRIDE 0x71188 |
| #define _DSPBPOS 0x7118C |
| #define _DSPBSIZE 0x71190 |
| #define _DSPBSURF 0x7119C |
| #define _DSPBTILEOFF 0x711A4 |
| |
| /* Sprite A control */ |
| #define _DVSACNTR 0x72180 |
| #define DVS_ENABLE (1<<31) |
| #define DVS_GAMMA_ENABLE (1<<30) |
| #define DVS_PIXFORMAT_MASK (3<<25) |
| #define DVS_FORMAT_YUV422 (0<<25) |
| #define DVS_FORMAT_RGBX101010 (1<<25) |
| #define DVS_FORMAT_RGBX888 (2<<25) |
| #define DVS_FORMAT_RGBX161616 (3<<25) |
| #define DVS_SOURCE_KEY (1<<22) |
| #define DVS_RGB_ORDER_XBGR (1<<20) |
| #define DVS_YUV_BYTE_ORDER_MASK (3<<16) |
| #define DVS_YUV_ORDER_YUYV (0<<16) |
| #define DVS_YUV_ORDER_UYVY (1<<16) |
| #define DVS_YUV_ORDER_YVYU (2<<16) |
| #define DVS_YUV_ORDER_VYUY (3<<16) |
| #define DVS_DEST_KEY (1<<2) |
| #define DVS_TRICKLE_FEED_DISABLE (1<<14) |
| #define DVS_TILED (1<<10) |
| #define _DVSALINOFF 0x72184 |
| #define _DVSASTRIDE 0x72188 |
| #define _DVSAPOS 0x7218c |
| #define _DVSASIZE 0x72190 |
| #define _DVSAKEYVAL 0x72194 |
| #define _DVSAKEYMSK 0x72198 |
| #define _DVSASURF 0x7219c |
| #define _DVSAKEYMAXVAL 0x721a0 |
| #define _DVSATILEOFF 0x721a4 |
| #define _DVSASURFLIVE 0x721ac |
| #define _DVSASCALE 0x72204 |
| #define DVS_SCALE_ENABLE (1<<31) |
| #define DVS_FILTER_MASK (3<<29) |
| #define DVS_FILTER_MEDIUM (0<<29) |
| #define DVS_FILTER_ENHANCING (1<<29) |
| #define DVS_FILTER_SOFTENING (2<<29) |
| #define DVS_VERTICAL_OFFSET_HALF (1<<28) /* must be enabled below */ |
| #define DVS_VERTICAL_OFFSET_ENABLE (1<<27) |
| #define _DVSAGAMC 0x72300 |
| |
| #define _DVSBCNTR 0x73180 |
| #define _DVSBLINOFF 0x73184 |
| #define _DVSBSTRIDE 0x73188 |
| #define _DVSBPOS 0x7318c |
| #define _DVSBSIZE 0x73190 |
| #define _DVSBKEYVAL 0x73194 |
| #define _DVSBKEYMSK 0x73198 |
| #define _DVSBSURF 0x7319c |
| #define _DVSBKEYMAXVAL 0x731a0 |
| #define _DVSBTILEOFF 0x731a4 |
| #define _DVSBSURFLIVE 0x731ac |
| #define _DVSBSCALE 0x73204 |
| #define _DVSBGAMC 0x73300 |
| |
| #define DVSCNTR(pipe) _PIPE(pipe, _DVSACNTR, _DVSBCNTR) |
| #define DVSLINOFF(pipe) _PIPE(pipe, _DVSALINOFF, _DVSBLINOFF) |
| #define DVSSTRIDE(pipe) _PIPE(pipe, _DVSASTRIDE, _DVSBSTRIDE) |
| #define DVSPOS(pipe) _PIPE(pipe, _DVSAPOS, _DVSBPOS) |
| #define DVSSURF(pipe) _PIPE(pipe, _DVSASURF, _DVSBSURF) |
| #define DVSKEYMAX(pipe) _PIPE(pipe, _DVSAKEYMAXVAL, _DVSBKEYMAXVAL) |
| #define DVSSIZE(pipe) _PIPE(pipe, _DVSASIZE, _DVSBSIZE) |
| #define DVSSCALE(pipe) _PIPE(pipe, _DVSASCALE, _DVSBSCALE) |
| #define DVSTILEOFF(pipe) _PIPE(pipe, _DVSATILEOFF, _DVSBTILEOFF) |
| #define DVSKEYVAL(pipe) _PIPE(pipe, _DVSAKEYVAL, _DVSBKEYVAL) |
| #define DVSKEYMSK(pipe) _PIPE(pipe, _DVSAKEYMSK, _DVSBKEYMSK) |
| |
| #define _SPRA_CTL 0x70280 |
| #define SPRITE_ENABLE (1<<31) |
| #define SPRITE_GAMMA_ENABLE (1<<30) |
| #define SPRITE_PIXFORMAT_MASK (7<<25) |
| #define SPRITE_FORMAT_YUV422 (0<<25) |
| #define SPRITE_FORMAT_RGBX101010 (1<<25) |
| #define SPRITE_FORMAT_RGBX888 (2<<25) |
| #define SPRITE_FORMAT_RGBX161616 (3<<25) |
| #define SPRITE_FORMAT_YUV444 (4<<25) |
| #define SPRITE_FORMAT_XR_BGR101010 (5<<25) /* Extended range */ |
| #define SPRITE_CSC_ENABLE (1<<24) |
| #define SPRITE_SOURCE_KEY (1<<22) |
| #define SPRITE_RGB_ORDER_RGBX (1<<20) /* only for 888 and 161616 */ |
| #define SPRITE_YUV_TO_RGB_CSC_DISABLE (1<<19) |
| #define SPRITE_YUV_CSC_FORMAT_BT709 (1<<18) /* 0 is BT601 */ |
| #define SPRITE_YUV_BYTE_ORDER_MASK (3<<16) |
| #define SPRITE_YUV_ORDER_YUYV (0<<16) |
| #define SPRITE_YUV_ORDER_UYVY (1<<16) |
| #define SPRITE_YUV_ORDER_YVYU (2<<16) |
| #define SPRITE_YUV_ORDER_VYUY (3<<16) |
| #define SPRITE_TRICKLE_FEED_DISABLE (1<<14) |
| #define SPRITE_INT_GAMMA_ENABLE (1<<13) |
| #define SPRITE_TILED (1<<10) |
| #define SPRITE_DEST_KEY (1<<2) |
| #define _SPRA_LINOFF 0x70284 |
| #define _SPRA_STRIDE 0x70288 |
| #define _SPRA_POS 0x7028c |
| #define _SPRA_SIZE 0x70290 |
| #define _SPRA_KEYVAL 0x70294 |
| #define _SPRA_KEYMSK 0x70298 |
| #define _SPRA_SURF 0x7029c |
| #define _SPRA_KEYMAX 0x702a0 |
| #define _SPRA_TILEOFF 0x702a4 |
| #define _SPRA_SCALE 0x70304 |
| #define SPRITE_SCALE_ENABLE (1<<31) |
| #define SPRITE_FILTER_MASK (3<<29) |
| #define SPRITE_FILTER_MEDIUM (0<<29) |
| #define SPRITE_FILTER_ENHANCING (1<<29) |
| #define SPRITE_FILTER_SOFTENING (2<<29) |
| #define SPRITE_VERTICAL_OFFSET_HALF (1<<28) /* must be enabled below */ |
| #define SPRITE_VERTICAL_OFFSET_ENABLE (1<<27) |
| #define _SPRA_GAMC 0x70400 |
| |
| #define _SPRB_CTL 0x71280 |
| #define _SPRB_LINOFF 0x71284 |
| #define _SPRB_STRIDE 0x71288 |
| #define _SPRB_POS 0x7128c |
| #define _SPRB_SIZE 0x71290 |
| #define _SPRB_KEYVAL 0x71294 |
| #define _SPRB_KEYMSK 0x71298 |
| #define _SPRB_SURF 0x7129c |
| #define _SPRB_KEYMAX 0x712a0 |
| #define _SPRB_TILEOFF 0x712a4 |
| #define _SPRB_SCALE 0x71304 |
| #define _SPRB_GAMC 0x71400 |
| |
| #define SPRCTL(pipe) _PIPE(pipe, _SPRA_CTL, _SPRB_CTL) |
| #define SPRLINOFF(pipe) _PIPE(pipe, _SPRA_LINOFF, _SPRB_LINOFF) |
| #define SPRSTRIDE(pipe) _PIPE(pipe, _SPRA_STRIDE, _SPRB_STRIDE) |
| #define SPRPOS(pipe) _PIPE(pipe, _SPRA_POS, _SPRB_POS) |
| #define SPRSIZE(pipe) _PIPE(pipe, _SPRA_SIZE, _SPRB_SIZE) |
| #define SPRKEYVAL(pipe) _PIPE(pipe, _SPRA_KEYVAL, _SPRB_KEYVAL) |
| #define SPRKEYMSK(pipe) _PIPE(pipe, _SPRA_KEYMSK, _SPRB_KEYMSK) |
| #define SPRSURF(pipe) _PIPE(pipe, _SPRA_SURF, _SPRB_SURF) |
| #define SPRKEYMAX(pipe) _PIPE(pipe, _SPRA_KEYMAX, _SPRB_KEYMAX) |
| #define SPRTILEOFF(pipe) _PIPE(pipe, _SPRA_TILEOFF, _SPRB_TILEOFF) |
| #define SPRSCALE(pipe) _PIPE(pipe, _SPRA_SCALE, _SPRB_SCALE) |
| #define SPRGAMC(pipe) _PIPE(pipe, _SPRA_GAMC, _SPRB_GAMC) |
| |
| /* VBIOS regs */ |
| #define VGACNTRL 0x71400 |
| # define VGA_DISP_DISABLE (1 << 31) |
| # define VGA_2X_MODE (1 << 30) |
| # define VGA_PIPE_B_SELECT (1 << 29) |
| |
| /* Ironlake */ |
| |
| #define CPU_VGACNTRL 0x41000 |
| |
| #define DIGITAL_PORT_HOTPLUG_CNTRL 0x44030 |
| #define DIGITAL_PORTA_HOTPLUG_ENABLE (1 << 4) |
| #define DIGITAL_PORTA_SHORT_PULSE_2MS (0 << 2) |
| #define DIGITAL_PORTA_SHORT_PULSE_4_5MS (1 << 2) |
| #define DIGITAL_PORTA_SHORT_PULSE_6MS (2 << 2) |
| #define DIGITAL_PORTA_SHORT_PULSE_100MS (3 << 2) |
| #define DIGITAL_PORTA_NO_DETECT (0 << 0) |
| #define DIGITAL_PORTA_LONG_PULSE_DETECT_MASK (1 << 1) |
| #define DIGITAL_PORTA_SHORT_PULSE_DETECT_MASK (1 << 0) |
| |
| /* refresh rate hardware control */ |
| #define RR_HW_CTL 0x45300 |
| #define RR_HW_LOW_POWER_FRAMES_MASK 0xff |
| #define RR_HW_HIGH_POWER_FRAMES_MASK 0xff00 |
| |
| #define FDI_PLL_BIOS_0 0x46000 |
| #define FDI_PLL_FB_CLOCK_MASK 0xff |
| #define FDI_PLL_BIOS_1 0x46004 |
| #define FDI_PLL_BIOS_2 0x46008 |
| #define DISPLAY_PORT_PLL_BIOS_0 0x4600c |
| #define DISPLAY_PORT_PLL_BIOS_1 0x46010 |
| #define DISPLAY_PORT_PLL_BIOS_2 0x46014 |
| |
| #define PCH_DSPCLK_GATE_D 0x42020 |
| # define DPFCUNIT_CLOCK_GATE_DISABLE (1 << 9) |
| # define DPFCRUNIT_CLOCK_GATE_DISABLE (1 << 8) |
| # define DPFDUNIT_CLOCK_GATE_DISABLE (1 << 7) |
| # define DPARBUNIT_CLOCK_GATE_DISABLE (1 << 5) |
| |
| #define PCH_3DCGDIS0 0x46020 |
| # define MARIUNIT_CLOCK_GATE_DISABLE (1 << 18) |
| # define SVSMUNIT_CLOCK_GATE_DISABLE (1 << 1) |
| |
| #define PCH_3DCGDIS1 0x46024 |
| # define VFMUNIT_CLOCK_GATE_DISABLE (1 << 11) |
| |
| #define FDI_PLL_FREQ_CTL 0x46030 |
| #define FDI_PLL_FREQ_CHANGE_REQUEST (1<<24) |
| #define FDI_PLL_FREQ_LOCK_LIMIT_MASK 0xfff00 |
| #define FDI_PLL_FREQ_DISABLE_COUNT_LIMIT_MASK 0xff |
| |
| |
| #define _PIPEA_DATA_M1 0x60030 |
| #define TU_SIZE(x) (((x)-1) << 25) /* default size 64 */ |
| #define TU_SIZE_MASK 0x7e000000 |
| #define PIPE_DATA_M1_OFFSET 0 |
| #define _PIPEA_DATA_N1 0x60034 |
| #define PIPE_DATA_N1_OFFSET 0 |
| |
| #define _PIPEA_DATA_M2 0x60038 |
| #define PIPE_DATA_M2_OFFSET 0 |
| #define _PIPEA_DATA_N2 0x6003c |
| #define PIPE_DATA_N2_OFFSET 0 |
| |
| #define _PIPEA_LINK_M1 0x60040 |
| #define PIPE_LINK_M1_OFFSET 0 |
| #define _PIPEA_LINK_N1 0x60044 |
| #define PIPE_LINK_N1_OFFSET 0 |
| |
| #define _PIPEA_LINK_M2 0x60048 |
| #define PIPE_LINK_M2_OFFSET 0 |
| #define _PIPEA_LINK_N2 0x6004c |
| #define PIPE_LINK_N2_OFFSET 0 |
| |
| /* PIPEB timing regs are same start from 0x61000 */ |
| |
| #define _PIPEB_DATA_M1 0x61030 |
| #define _PIPEB_DATA_N1 0x61034 |
| |
| #define _PIPEB_DATA_M2 0x61038 |
| #define _PIPEB_DATA_N2 0x6103c |
| |
| #define _PIPEB_LINK_M1 0x61040 |
| #define _PIPEB_LINK_N1 0x61044 |
| |
| #define _PIPEB_LINK_M2 0x61048 |
| #define _PIPEB_LINK_N2 0x6104c |
| |
| #define PIPE_DATA_M1(pipe) _PIPE(pipe, _PIPEA_DATA_M1, _PIPEB_DATA_M1) |
| #define PIPE_DATA_N1(pipe) _PIPE(pipe, _PIPEA_DATA_N1, _PIPEB_DATA_N1) |
| #define PIPE_DATA_M2(pipe) _PIPE(pipe, _PIPEA_DATA_M2, _PIPEB_DATA_M2) |
| #define PIPE_DATA_N2(pipe) _PIPE(pipe, _PIPEA_DATA_N2, _PIPEB_DATA_N2) |
| #define PIPE_LINK_M1(pipe) _PIPE(pipe, _PIPEA_LINK_M1, _PIPEB_LINK_M1) |
| #define PIPE_LINK_N1(pipe) _PIPE(pipe, _PIPEA_LINK_N1, _PIPEB_LINK_N1) |
| #define PIPE_LINK_M2(pipe) _PIPE(pipe, _PIPEA_LINK_M2, _PIPEB_LINK_M2) |
| #define PIPE_LINK_N2(pipe) _PIPE(pipe, _PIPEA_LINK_N2, _PIPEB_LINK_N2) |
| |
| /* CPU panel fitter */ |
| /* IVB+ has 3 fitters, 0 is 7x5 capable, the other two only 3x3 */ |
| #define _PFA_CTL_1 0x68080 |
| #define _PFB_CTL_1 0x68880 |
| #define PF_ENABLE (1<<31) |
| #define PF_FILTER_MASK (3<<23) |
| #define PF_FILTER_PROGRAMMED (0<<23) |
| #define PF_FILTER_MED_3x3 (1<<23) |
| #define PF_FILTER_EDGE_ENHANCE (2<<23) |
| #define PF_FILTER_EDGE_SOFTEN (3<<23) |
| #define _PFA_WIN_SZ 0x68074 |
| #define _PFB_WIN_SZ 0x68874 |
| #define _PFA_WIN_POS 0x68070 |
| #define _PFB_WIN_POS 0x68870 |
| #define _PFA_VSCALE 0x68084 |
| #define _PFB_VSCALE 0x68884 |
| #define _PFA_HSCALE 0x68090 |
| #define _PFB_HSCALE 0x68890 |
| |
| #define PF_CTL(pipe) _PIPE(pipe, _PFA_CTL_1, _PFB_CTL_1) |
| #define PF_WIN_SZ(pipe) _PIPE(pipe, _PFA_WIN_SZ, _PFB_WIN_SZ) |
| #define PF_WIN_POS(pipe) _PIPE(pipe, _PFA_WIN_POS, _PFB_WIN_POS) |
| #define PF_VSCALE(pipe) _PIPE(pipe, _PFA_VSCALE, _PFB_VSCALE) |
| #define PF_HSCALE(pipe) _PIPE(pipe, _PFA_HSCALE, _PFB_HSCALE) |
| |
| /* legacy palette */ |
| #define _LGC_PALETTE_A 0x4a000 |
| #define _LGC_PALETTE_B 0x4a800 |
| #define LGC_PALETTE(pipe) _PIPE(pipe, _LGC_PALETTE_A, _LGC_PALETTE_B) |
| |
| /* interrupts */ |
| #define DE_MASTER_IRQ_CONTROL (1 << 31) |
| #define DE_SPRITEB_FLIP_DONE (1 << 29) |
| #define DE_SPRITEA_FLIP_DONE (1 << 28) |
| #define DE_PLANEB_FLIP_DONE (1 << 27) |
| #define DE_PLANEA_FLIP_DONE (1 << 26) |
| #define DE_PCU_EVENT (1 << 25) |
| #define DE_GTT_FAULT (1 << 24) |
| #define DE_POISON (1 << 23) |
| #define DE_PERFORM_COUNTER (1 << 22) |
| #define DE_PCH_EVENT (1 << 21) |
| #define DE_AUX_CHANNEL_A (1 << 20) |
| #define DE_DP_A_HOTPLUG (1 << 19) |
| #define DE_GSE (1 << 18) |
| #define DE_PIPEB_VBLANK (1 << 15) |
| #define DE_PIPEB_EVEN_FIELD (1 << 14) |
| #define DE_PIPEB_ODD_FIELD (1 << 13) |
| #define DE_PIPEB_LINE_COMPARE (1 << 12) |
| #define DE_PIPEB_VSYNC (1 << 11) |
| #define DE_PIPEB_FIFO_UNDERRUN (1 << 8) |
| #define DE_PIPEA_VBLANK (1 << 7) |
| #define DE_PIPEA_EVEN_FIELD (1 << 6) |
| #define DE_PIPEA_ODD_FIELD (1 << 5) |
| #define DE_PIPEA_LINE_COMPARE (1 << 4) |
| #define DE_PIPEA_VSYNC (1 << 3) |
| #define DE_PIPEA_FIFO_UNDERRUN (1 << 0) |
| |
| /* More Ivybridge lolz */ |
| #define DE_ERR_DEBUG_IVB (1<<30) |
| #define DE_GSE_IVB (1<<29) |
| #define DE_PCH_EVENT_IVB (1<<28) |
| #define DE_DP_A_HOTPLUG_IVB (1<<27) |
| #define DE_AUX_CHANNEL_A_IVB (1<<26) |
| #define DE_SPRITEC_FLIP_DONE_IVB (1<<14) |
| #define DE_PLANEC_FLIP_DONE_IVB (1<<13) |
| #define DE_PIPEC_VBLANK_IVB (1<<10) |
| #define DE_SPRITEB_FLIP_DONE_IVB (1<<9) |
| #define DE_PLANEB_FLIP_DONE_IVB (1<<8) |
| #define DE_PIPEB_VBLANK_IVB (1<<5) |
| #define DE_SPRITEA_FLIP_DONE_IVB (1<<4) |
| #define DE_PLANEA_FLIP_DONE_IVB (1<<3) |
| #define DE_PIPEA_VBLANK_IVB (1<<0) |
| |
| #define VLV_MASTER_IER 0x4400c /* Gunit master IER */ |
| #define MASTER_INTERRUPT_ENABLE (1<<31) |
| |
| #define DEISR 0x44000 |
| #define DEIMR 0x44004 |
| #define DEIIR 0x44008 |
| #define DEIER 0x4400c |
| |
| /* GT interrupt. |
| * Note that for gen6+ the ring-specific interrupt bits do alias with the |
| * corresponding bits in the per-ring interrupt control registers. */ |
| #define GT_GEN6_BLT_FLUSHDW_NOTIFY_INTERRUPT (1 << 26) |
| #define GT_GEN6_BLT_CS_ERROR_INTERRUPT (1 << 25) |
| #define GT_GEN6_BLT_USER_INTERRUPT (1 << 22) |
| #define GT_GEN6_BSD_CS_ERROR_INTERRUPT (1 << 15) |
| #define GT_GEN6_BSD_USER_INTERRUPT (1 << 12) |
| #define GT_BSD_USER_INTERRUPT (1 << 5) /* ilk only */ |
| #define GT_GEN7_L3_PARITY_ERROR_INTERRUPT (1 << 5) |
| #define GT_PIPE_NOTIFY (1 << 4) |
| #define GT_RENDER_CS_ERROR_INTERRUPT (1 << 3) |
| #define GT_SYNC_STATUS (1 << 2) |
| #define GT_USER_INTERRUPT (1 << 0) |
| |
| #define GTISR 0x44010 |
| #define GTIMR 0x44014 |
| #define GTIIR 0x44018 |
| #define GTIER 0x4401c |
| |
| #define ILK_DISPLAY_CHICKEN2 0x42004 |
| /* Required on all Ironlake and Sandybridge according to the B-Spec. */ |
| #define ILK_ELPIN_409_SELECT (1 << 25) |
| #define ILK_DPARB_GATE (1<<22) |
| #define ILK_VSDPFD_FULL (1<<21) |
| #define ILK_DISPLAY_CHICKEN_FUSES 0x42014 |
| #define ILK_INTERNAL_GRAPHICS_DISABLE (1<<31) |
| #define ILK_INTERNAL_DISPLAY_DISABLE (1<<30) |
| #define ILK_DISPLAY_DEBUG_DISABLE (1<<29) |
| #define ILK_HDCP_DISABLE (1<<25) |
| #define ILK_eDP_A_DISABLE (1<<24) |
| #define ILK_DESKTOP (1<<23) |
| #define ILK_DSPCLK_GATE 0x42020 |
| #define IVB_VRHUNIT_CLK_GATE (1<<28) |
| #define ILK_DPARB_CLK_GATE (1<<5) |
| #define ILK_DPFD_CLK_GATE (1<<7) |
| |
| /* According to spec this bit 7/8/9 of 0x42020 should be set to enable FBC */ |
| #define ILK_CLK_FBC (1<<7) |
| #define ILK_DPFC_DIS1 (1<<8) |
| #define ILK_DPFC_DIS2 (1<<9) |
| |
| #define IVB_CHICKEN3 0x4200c |
| # define CHICKEN3_DGMG_REQ_OUT_FIX_DISABLE (1 << 5) |
| # define CHICKEN3_DGMG_DONE_FIX_DISABLE (1 << 2) |
| |
| #define DISP_ARB_CTL 0x45000 |
| #define DISP_TILE_SURFACE_SWIZZLING (1<<13) |
| #define DISP_FBC_WM_DIS (1<<15) |
| |
| /* GEN7 chicken */ |
| #define GEN7_COMMON_SLICE_CHICKEN1 0x7010 |
| # define GEN7_CSC1_RHWO_OPT_DISABLE_IN_RCC ((1<<10) | (1<<26)) |
| |
| #define GEN7_L3CNTLREG1 0xB01C |
| #define GEN7_WA_FOR_GEN7_L3_CONTROL 0x3C4FFF8C |
| |
| #define GEN7_L3_CHICKEN_MODE_REGISTER 0xB030 |
| #define GEN7_WA_L3_CHICKEN_MODE 0x20000000 |
| |
| /* WaCatErrorRejectionIssue */ |
| #define GEN7_SQ_CHICKEN_MBCUNIT_CONFIG 0x9030 |
| #define GEN7_SQ_CHICKEN_MBCUNIT_SQINTMOB (1<<11) |
| |
| /* PCH */ |
| |
| /* south display engine interrupt: IBX */ |
| #define SDE_AUDIO_POWER_D (1 << 27) |
| #define SDE_AUDIO_POWER_C (1 << 26) |
| #define SDE_AUDIO_POWER_B (1 << 25) |
| #define SDE_AUDIO_POWER_SHIFT (25) |
| #define SDE_AUDIO_POWER_MASK (7 << SDE_AUDIO_POWER_SHIFT) |
| #define SDE_GMBUS (1 << 24) |
| #define SDE_AUDIO_HDCP_TRANSB (1 << 23) |
| #define SDE_AUDIO_HDCP_TRANSA (1 << 22) |
| #define SDE_AUDIO_HDCP_MASK (3 << 22) |
| #define SDE_AUDIO_TRANSB (1 << 21) |
| #define SDE_AUDIO_TRANSA (1 << 20) |
| #define SDE_AUDIO_TRANS_MASK (3 << 20) |
| #define SDE_POISON (1 << 19) |
| /* 18 reserved */ |
| #define SDE_FDI_RXB (1 << 17) |
| #define SDE_FDI_RXA (1 << 16) |
| #define SDE_FDI_MASK (3 << 16) |
| #define SDE_AUXD (1 << 15) |
| #define SDE_AUXC (1 << 14) |
| #define SDE_AUXB (1 << 13) |
| #define SDE_AUX_MASK (7 << 13) |
| /* 12 reserved */ |
| #define SDE_CRT_HOTPLUG (1 << 11) |
| #define SDE_PORTD_HOTPLUG (1 << 10) |
| #define SDE_PORTC_HOTPLUG (1 << 9) |
| #define SDE_PORTB_HOTPLUG (1 << 8) |
| #define SDE_SDVOB_HOTPLUG (1 << 6) |
| #define SDE_HOTPLUG_MASK (0xf << 8) |
| #define SDE_TRANSB_CRC_DONE (1 << 5) |
| #define SDE_TRANSB_CRC_ERR (1 << 4) |
| #define SDE_TRANSB_FIFO_UNDER (1 << 3) |
| #define SDE_TRANSA_CRC_DONE (1 << 2) |
| #define SDE_TRANSA_CRC_ERR (1 << 1) |
| #define SDE_TRANSA_FIFO_UNDER (1 << 0) |
| #define SDE_TRANS_MASK (0x3f) |
| |
| /* south display engine interrupt: CPT/PPT */ |
| #define SDE_AUDIO_POWER_D_CPT (1 << 31) |
| #define SDE_AUDIO_POWER_C_CPT (1 << 30) |
| #define SDE_AUDIO_POWER_B_CPT (1 << 29) |
| #define SDE_AUDIO_POWER_SHIFT_CPT 29 |
| #define SDE_AUDIO_POWER_MASK_CPT (7 << 29) |
| #define SDE_AUXD_CPT (1 << 27) |
| #define SDE_AUXC_CPT (1 << 26) |
| #define SDE_AUXB_CPT (1 << 25) |
| #define SDE_AUX_MASK_CPT (7 << 25) |
| #define SDE_PORTD_HOTPLUG_CPT (1 << 23) |
| #define SDE_PORTC_HOTPLUG_CPT (1 << 22) |
| #define SDE_PORTB_HOTPLUG_CPT (1 << 21) |
| #define SDE_CRT_HOTPLUG_CPT (1 << 19) |
| #define SDE_HOTPLUG_MASK_CPT (SDE_CRT_HOTPLUG_CPT | \ |
| SDE_PORTD_HOTPLUG_CPT | \ |
| SDE_PORTC_HOTPLUG_CPT | \ |
| SDE_PORTB_HOTPLUG_CPT) |
| #define SDE_GMBUS_CPT (1 << 17) |
| #define SDE_AUDIO_CP_REQ_C_CPT (1 << 10) |
| #define SDE_AUDIO_CP_CHG_C_CPT (1 << 9) |
| #define SDE_FDI_RXC_CPT (1 << 8) |
| #define SDE_AUDIO_CP_REQ_B_CPT (1 << 6) |
| #define SDE_AUDIO_CP_CHG_B_CPT (1 << 5) |
| #define SDE_FDI_RXB_CPT (1 << 4) |
| #define SDE_AUDIO_CP_REQ_A_CPT (1 << 2) |
| #define SDE_AUDIO_CP_CHG_A_CPT (1 << 1) |
| #define SDE_FDI_RXA_CPT (1 << 0) |
| #define SDE_AUDIO_CP_REQ_CPT (SDE_AUDIO_CP_REQ_C_CPT | \ |
| SDE_AUDIO_CP_REQ_B_CPT | \ |
| SDE_AUDIO_CP_REQ_A_CPT) |
| #define SDE_AUDIO_CP_CHG_CPT (SDE_AUDIO_CP_CHG_C_CPT | \ |
| SDE_AUDIO_CP_CHG_B_CPT | \ |
| SDE_AUDIO_CP_CHG_A_CPT) |
| #define SDE_FDI_MASK_CPT (SDE_FDI_RXC_CPT | \ |
| SDE_FDI_RXB_CPT | \ |
| SDE_FDI_RXA_CPT) |
| |
| #define SDEISR 0xc4000 |
| #define SDEIMR 0xc4004 |
| #define SDEIIR 0xc4008 |
| #define SDEIER 0xc400c |
| |
| /* digital port hotplug */ |
| #define PCH_PORT_HOTPLUG 0xc4030 /* SHOTPLUG_CTL */ |
| #define PORTD_HOTPLUG_ENABLE (1 << 20) |
| #define PORTD_PULSE_DURATION_2ms (0) |
| #define PORTD_PULSE_DURATION_4_5ms (1 << 18) |
| #define PORTD_PULSE_DURATION_6ms (2 << 18) |
| #define PORTD_PULSE_DURATION_100ms (3 << 18) |
| #define PORTD_PULSE_DURATION_MASK (3 << 18) |
| #define PORTD_HOTPLUG_NO_DETECT (0) |
| #define PORTD_HOTPLUG_SHORT_DETECT (1 << 16) |
| #define PORTD_HOTPLUG_LONG_DETECT (1 << 17) |
| #define PORTC_HOTPLUG_ENABLE (1 << 12) |
| #define PORTC_PULSE_DURATION_2ms (0) |
| #define PORTC_PULSE_DURATION_4_5ms (1 << 10) |
| #define PORTC_PULSE_DURATION_6ms (2 << 10) |
| #define PORTC_PULSE_DURATION_100ms (3 << 10) |
| #define PORTC_PULSE_DURATION_MASK (3 << 10) |
| #define PORTC_HOTPLUG_NO_DETECT (0) |
| #define PORTC_HOTPLUG_SHORT_DETECT (1 << 8) |
| #define PORTC_HOTPLUG_LONG_DETECT (1 << 9) |
| #define PORTB_HOTPLUG_ENABLE (1 << 4) |
| #define PORTB_PULSE_DURATION_2ms (0) |
| #define PORTB_PULSE_DURATION_4_5ms (1 << 2) |
| #define PORTB_PULSE_DURATION_6ms (2 << 2) |
| #define PORTB_PULSE_DURATION_100ms (3 << 2) |
| #define PORTB_PULSE_DURATION_MASK (3 << 2) |
| #define PORTB_HOTPLUG_NO_DETECT (0) |
| #define PORTB_HOTPLUG_SHORT_DETECT (1 << 0) |
| #define PORTB_HOTPLUG_LONG_DETECT (1 << 1) |
| |
| #define PCH_GPIOA 0xc5010 |
| #define PCH_GPIOB 0xc5014 |
| #define PCH_GPIOC 0xc5018 |
| #define PCH_GPIOD 0xc501c |
| #define PCH_GPIOE 0xc5020 |
| #define PCH_GPIOF 0xc5024 |
| |
| #define PCH_GMBUS0 0xc5100 |
| #define PCH_GMBUS1 0xc5104 |
| #define PCH_GMBUS2 0xc5108 |
| #define PCH_GMBUS3 0xc510c |
| #define PCH_GMBUS4 0xc5110 |
| #define PCH_GMBUS5 0xc5120 |
| |
| #define _PCH_DPLL_A 0xc6014 |
| #define _PCH_DPLL_B 0xc6018 |
| #define _PCH_DPLL(pll) (pll == 0 ? _PCH_DPLL_A : _PCH_DPLL_B) |
| |
| #define _PCH_FPA0 0xc6040 |
| #define FP_CB_TUNE (0x3<<22) |
| #define _PCH_FPA1 0xc6044 |
| #define _PCH_FPB0 0xc6048 |
| #define _PCH_FPB1 0xc604c |
| #define _PCH_FP0(pll) (pll == 0 ? _PCH_FPA0 : _PCH_FPB0) |
| #define _PCH_FP1(pll) (pll == 0 ? _PCH_FPA1 : _PCH_FPB1) |
| |
| #define PCH_DPLL_TEST 0xc606c |
| |
| #define PCH_DREF_CONTROL 0xC6200 |
| #define DREF_CONTROL_MASK 0x7fc3 |
| #define DREF_CPU_SOURCE_OUTPUT_DISABLE (0<<13) |
| #define DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD (2<<13) |
| #define DREF_CPU_SOURCE_OUTPUT_NONSPREAD (3<<13) |
| #define DREF_CPU_SOURCE_OUTPUT_MASK (3<<13) |
| #define DREF_SSC_SOURCE_DISABLE (0<<11) |
| #define DREF_SSC_SOURCE_ENABLE (2<<11) |
| #define DREF_SSC_SOURCE_MASK (3<<11) |
| #define DREF_NONSPREAD_SOURCE_DISABLE (0<<9) |
| #define DREF_NONSPREAD_CK505_ENABLE (1<<9) |
| #define DREF_NONSPREAD_SOURCE_ENABLE (2<<9) |
| #define DREF_NONSPREAD_SOURCE_MASK (3<<9) |
| #define DREF_SUPERSPREAD_SOURCE_DISABLE (0<<7) |
| #define DREF_SUPERSPREAD_SOURCE_ENABLE (2<<7) |
| #define DREF_SUPERSPREAD_SOURCE_MASK (3<<7) |
| #define DREF_SSC4_DOWNSPREAD (0<<6) |
| #define DREF_SSC4_CENTERSPREAD (1<<6) |
| #define DREF_SSC1_DISABLE (0<<1) |
| #define DREF_SSC1_ENABLE (1<<1) |
| #define DREF_SSC4_DISABLE (0) |
| #define DREF_SSC4_ENABLE (1) |
| |
| #define PCH_RAWCLK_FREQ 0xc6204 |
| #define FDL_TP1_TIMER_SHIFT 12 |
| #define FDL_TP1_TIMER_MASK (3<<12) |
| #define FDL_TP2_TIMER_SHIFT 10 |
| #define FDL_TP2_TIMER_MASK (3<<10) |
| #define RAWCLK_FREQ_MASK 0x3ff |
| |
| #define PCH_DPLL_TMR_CFG 0xc6208 |
| |
| #define PCH_SSC4_PARMS 0xc6210 |
| #define PCH_SSC4_AUX_PARMS 0xc6214 |
| |
| #define PCH_DPLL_SEL 0xc7000 |
| #define TRANSA_DPLL_ENABLE (1<<3) |
| #define TRANSA_DPLLB_SEL (1<<0) |
| #define TRANSA_DPLLA_SEL 0 |
| #define TRANSB_DPLL_ENABLE (1<<7) |
| #define TRANSB_DPLLB_SEL (1<<4) |
| #define TRANSB_DPLLA_SEL (0) |
| #define TRANSC_DPLL_ENABLE (1<<11) |
| #define TRANSC_DPLLB_SEL (1<<8) |
| #define TRANSC_DPLLA_SEL (0) |
| |
| /* transcoder */ |
| |
| #define _TRANS_HTOTAL_A 0xe0000 |
| #define TRANS_HTOTAL_SHIFT 16 |
| #define TRANS_HACTIVE_SHIFT 0 |
| #define _TRANS_HBLANK_A 0xe0004 |
| #define TRANS_HBLANK_END_SHIFT 16 |
| #define TRANS_HBLANK_START_SHIFT 0 |
| #define _TRANS_HSYNC_A 0xe0008 |
| #define TRANS_HSYNC_END_SHIFT 16 |
| #define TRANS_HSYNC_START_SHIFT 0 |
| #define _TRANS_VTOTAL_A 0xe000c |
| #define TRANS_VTOTAL_SHIFT 16 |
| #define TRANS_VACTIVE_SHIFT 0 |
| #define _TRANS_VBLANK_A 0xe0010 |
| #define TRANS_VBLANK_END_SHIFT 16 |
| #define TRANS_VBLANK_START_SHIFT 0 |
| #define _TRANS_VSYNC_A 0xe0014 |
| #define TRANS_VSYNC_END_SHIFT 16 |
| #define TRANS_VSYNC_START_SHIFT 0 |
| #define _TRANS_VSYNCSHIFT_A 0xe0028 |
| |
| #define _TRANSA_DATA_M1 0xe0030 |
| #define _TRANSA_DATA_N1 0xe0034 |
| #define _TRANSA_DATA_M2 0xe0038 |
| #define _TRANSA_DATA_N2 0xe003c |
| #define _TRANSA_DP_LINK_M1 0xe0040 |
| #define _TRANSA_DP_LINK_N1 0xe0044 |
| #define _TRANSA_DP_LINK_M2 0xe0048 |
| #define _TRANSA_DP_LINK_N2 0xe004c |
| |
| /* Per-transcoder DIP controls */ |
| |
| #define _VIDEO_DIP_CTL_A 0xe0200 |
| #define _VIDEO_DIP_DATA_A 0xe0208 |
| #define _VIDEO_DIP_GCP_A 0xe0210 |
| |
| #define _VIDEO_DIP_CTL_B 0xe1200 |
| #define _VIDEO_DIP_DATA_B 0xe1208 |
| #define _VIDEO_DIP_GCP_B 0xe1210 |
| |
| #define TVIDEO_DIP_CTL(pipe) _PIPE(pipe, _VIDEO_DIP_CTL_A, _VIDEO_DIP_CTL_B) |
| #define TVIDEO_DIP_DATA(pipe) _PIPE(pipe, _VIDEO_DIP_DATA_A, _VIDEO_DIP_DATA_B) |
| #define TVIDEO_DIP_GCP(pipe) _PIPE(pipe, _VIDEO_DIP_GCP_A, _VIDEO_DIP_GCP_B) |
| |
| #define VLV_VIDEO_DIP_CTL_A 0x60220 |
| #define VLV_VIDEO_DIP_DATA_A 0x60208 |
| #define VLV_VIDEO_DIP_GDCP_PAYLOAD_A 0x60210 |
| |
| #define VLV_VIDEO_DIP_CTL_B 0x61170 |
| #define VLV_VIDEO_DIP_DATA_B 0x61174 |
| #define VLV_VIDEO_DIP_GDCP_PAYLOAD_B 0x61178 |
| |
| #define VLV_TVIDEO_DIP_CTL(pipe) \ |
| _PIPE(pipe, VLV_VIDEO_DIP_CTL_A, VLV_VIDEO_DIP_CTL_B) |
| #define VLV_TVIDEO_DIP_DATA(pipe) \ |
| _PIPE(pipe, VLV_VIDEO_DIP_DATA_A, VLV_VIDEO_DIP_DATA_B) |
| #define VLV_TVIDEO_DIP_GCP(pipe) \ |
| _PIPE(pipe, VLV_VIDEO_DIP_GDCP_PAYLOAD_A, VLV_VIDEO_DIP_GDCP_PAYLOAD_B) |
| |
| /* Haswell DIP controls */ |
| #define HSW_VIDEO_DIP_CTL_A 0x60200 |
| #define HSW_VIDEO_DIP_AVI_DATA_A 0x60220 |
| #define HSW_VIDEO_DIP_VS_DATA_A 0x60260 |
| #define HSW_VIDEO_DIP_SPD_DATA_A 0x602A0 |
| #define HSW_VIDEO_DIP_GMP_DATA_A 0x602E0 |
| #define HSW_VIDEO_DIP_VSC_DATA_A 0x60320 |
| #define HSW_VIDEO_DIP_AVI_ECC_A 0x60240 |
| #define HSW_VIDEO_DIP_VS_ECC_A 0x60280 |
| #define HSW_VIDEO_DIP_SPD_ECC_A 0x602C0 |
| #define HSW_VIDEO_DIP_GMP_ECC_A 0x60300 |
| #define HSW_VIDEO_DIP_VSC_ECC_A 0x60344 |
| #define HSW_VIDEO_DIP_GCP_A 0x60210 |
| |
| #define HSW_VIDEO_DIP_CTL_B 0x61200 |
| #define HSW_VIDEO_DIP_AVI_DATA_B 0x61220 |
| #define HSW_VIDEO_DIP_VS_DATA_B 0x61260 |
| #define HSW_VIDEO_DIP_SPD_DATA_B 0x612A0 |
| #define HSW_VIDEO_DIP_GMP_DATA_B 0x612E0 |
| #define HSW_VIDEO_DIP_VSC_DATA_B 0x61320 |
| #define HSW_VIDEO_DIP_BVI_ECC_B 0x61240 |
| #define HSW_VIDEO_DIP_VS_ECC_B 0x61280 |
| #define HSW_VIDEO_DIP_SPD_ECC_B 0x612C0 |
| #define HSW_VIDEO_DIP_GMP_ECC_B 0x61300 |
| #define HSW_VIDEO_DIP_VSC_ECC_B 0x61344 |
| #define HSW_VIDEO_DIP_GCP_B 0x61210 |
| |
| #define HSW_TVIDEO_DIP_CTL(pipe) \ |
| _PIPE(pipe, HSW_VIDEO_DIP_CTL_A, HSW_VIDEO_DIP_CTL_B) |
| #define HSW_TVIDEO_DIP_AVI_DATA(pipe) \ |
| _PIPE(pipe, HSW_VIDEO_DIP_AVI_DATA_A, HSW_VIDEO_DIP_AVI_DATA_B) |
| #define HSW_TVIDEO_DIP_SPD_DATA(pipe) \ |
| _PIPE(pipe, HSW_VIDEO_DIP_SPD_DATA_A, HSW_VIDEO_DIP_SPD_DATA_B) |
| #define HSW_TVIDEO_DIP_GCP(pipe) \ |
| _PIPE(pipe, HSW_VIDEO_DIP_GCP_A, HSW_VIDEO_DIP_GCP_B) |
| |
| #define _TRANS_HTOTAL_B 0xe1000 |
| #define _TRANS_HBLANK_B 0xe1004 |
| #define _TRANS_HSYNC_B 0xe1008 |
| #define _TRANS_VTOTAL_B 0xe100c |
| #define _TRANS_VBLANK_B 0xe1010 |
| #define _TRANS_VSYNC_B 0xe1014 |
| #define _TRANS_VSYNCSHIFT_B 0xe1028 |
| |
| #define TRANS_HTOTAL(pipe) _PIPE(pipe, _TRANS_HTOTAL_A, _TRANS_HTOTAL_B) |
| #define TRANS_HBLANK(pipe) _PIPE(pipe, _TRANS_HBLANK_A, _TRANS_HBLANK_B) |
| #define TRANS_HSYNC(pipe) _PIPE(pipe, _TRANS_HSYNC_A, _TRANS_HSYNC_B) |
| #define TRANS_VTOTAL(pipe) _PIPE(pipe, _TRANS_VTOTAL_A, _TRANS_VTOTAL_B) |
| #define TRANS_VBLANK(pipe) _PIPE(pipe, _TRANS_VBLANK_A, _TRANS_VBLANK_B) |
| #define TRANS_VSYNC(pipe) _PIPE(pipe, _TRANS_VSYNC_A, _TRANS_VSYNC_B) |
| #define TRANS_VSYNCSHIFT(pipe) _PIPE(pipe, _TRANS_VSYNCSHIFT_A, \ |
| _TRANS_VSYNCSHIFT_B) |
| |
| #define _TRANSB_DATA_M1 0xe1030 |
| #define _TRANSB_DATA_N1 0xe1034 |
| #define _TRANSB_DATA_M2 0xe1038 |
| #define _TRANSB_DATA_N2 0xe103c |
| #define _TRANSB_DP_LINK_M1 0xe1040 |
| #define _TRANSB_DP_LINK_N1 0xe1044 |
| #define _TRANSB_DP_LINK_M2 0xe1048 |
| #define _TRANSB_DP_LINK_N2 0xe104c |
| |
| #define TRANSDATA_M1(pipe) _PIPE(pipe, _TRANSA_DATA_M1, _TRANSB_DATA_M1) |
| #define TRANSDATA_N1(pipe) _PIPE(pipe, _TRANSA_DATA_N1, _TRANSB_DATA_N1) |
| #define TRANSDATA_M2(pipe) _PIPE(pipe, _TRANSA_DATA_M2, _TRANSB_DATA_M2) |
| #define TRANSDATA_N2(pipe) _PIPE(pipe, _TRANSA_DATA_N2, _TRANSB_DATA_N2) |
| #define TRANSDPLINK_M1(pipe) _PIPE(pipe, _TRANSA_DP_LINK_M1, _TRANSB_DP_LINK_M1) |
| #define TRANSDPLINK_N1(pipe) _PIPE(pipe, _TRANSA_DP_LINK_N1, _TRANSB_DP_LINK_N1) |
| #define TRANSDPLINK_M2(pipe) _PIPE(pipe, _TRANSA_DP_LINK_M2, _TRANSB_DP_LINK_M2) |
| #define TRANSDPLINK_N2(pipe) _PIPE(pipe, _TRANSA_DP_LINK_N2, _TRANSB_DP_LINK_N2) |
| |
| #define _TRANSACONF 0xf0008 |
| #define _TRANSBCONF 0xf1008 |
| #define TRANSCONF(plane) _PIPE(plane, _TRANSACONF, _TRANSBCONF) |
| #define TRANS_DISABLE (0<<31) |
| #define TRANS_ENABLE (1<<31) |
| #define TRANS_STATE_MASK (1<<30) |
| #define TRANS_STATE_DISABLE (0<<30) |
| #define TRANS_STATE_ENABLE (1<<30) |
| #define TRANS_FSYNC_DELAY_HB1 (0<<27) |
| #define TRANS_FSYNC_DELAY_HB2 (1<<27) |
| #define TRANS_FSYNC_DELAY_HB3 (2<<27) |
| #define TRANS_FSYNC_DELAY_HB4 (3<<27) |
| #define TRANS_DP_AUDIO_ONLY (1<<26) |
| #define TRANS_DP_VIDEO_AUDIO (0<<26) |
| #define TRANS_INTERLACE_MASK (7<<21) |
| #define TRANS_PROGRESSIVE (0<<21) |
| #define TRANS_INTERLACED (3<<21) |
| #define TRANS_LEGACY_INTERLACED_ILK (2<<21) |
| #define TRANS_8BPC (0<<5) |
| #define TRANS_10BPC (1<<5) |
| #define TRANS_6BPC (2<<5) |
| #define TRANS_12BPC (3<<5) |
| |
| #define _TRANSA_CHICKEN2 0xf0064 |
| #define _TRANSB_CHICKEN2 0xf1064 |
| #define TRANS_CHICKEN2(pipe) _PIPE(pipe, _TRANSA_CHICKEN2, _TRANSB_CHICKEN2) |
| #define TRANS_AUTOTRAIN_GEN_STALL_DIS (1<<31) |
| |
| #define SOUTH_CHICKEN1 0xc2000 |
| #define FDIA_PHASE_SYNC_SHIFT_OVR 19 |
| #define FDIA_PHASE_SYNC_SHIFT_EN 18 |
| #define FDI_PHASE_SYNC_OVR(pipe) (1<<(FDIA_PHASE_SYNC_SHIFT_OVR - ((pipe) * 2))) |
| #define FDI_PHASE_SYNC_EN(pipe) (1<<(FDIA_PHASE_SYNC_SHIFT_EN - ((pipe) * 2))) |
| #define SOUTH_CHICKEN2 0xc2004 |
| #define DPLS_EDP_PPS_FIX_DIS (1<<0) |
| |
| #define _FDI_RXA_CHICKEN 0xc200c |
| #define _FDI_RXB_CHICKEN 0xc2010 |
| #define FDI_RX_PHASE_SYNC_POINTER_OVR (1<<1) |
| #define FDI_RX_PHASE_SYNC_POINTER_EN (1<<0) |
| #define FDI_RX_CHICKEN(pipe) _PIPE(pipe, _FDI_RXA_CHICKEN, _FDI_RXB_CHICKEN) |
| |
| #define SOUTH_DSPCLK_GATE_D 0xc2020 |
| #define PCH_DPLSUNIT_CLOCK_GATE_DISABLE (1<<29) |
| |
| /* CPU: FDI_TX */ |
| #define _FDI_TXA_CTL 0x60100 |
| #define _FDI_TXB_CTL 0x61100 |
| #define FDI_TX_CTL(pipe) _PIPE(pipe, _FDI_TXA_CTL, _FDI_TXB_CTL) |
| #define FDI_TX_DISABLE (0<<31) |
| #define FDI_TX_ENABLE (1<<31) |
| #define FDI_LINK_TRAIN_PATTERN_1 (0<<28) |
| #define FDI_LINK_TRAIN_PATTERN_2 (1<<28) |
| #define FDI_LINK_TRAIN_PATTERN_IDLE (2<<28) |
| #define FDI_LINK_TRAIN_NONE (3<<28) |
| #define FDI_LINK_TRAIN_VOLTAGE_0_4V (0<<25) |
| #define FDI_LINK_TRAIN_VOLTAGE_0_6V (1<<25) |
| #define FDI_LINK_TRAIN_VOLTAGE_0_8V (2<<25) |
| #define FDI_LINK_TRAIN_VOLTAGE_1_2V (3<<25) |
| #define FDI_LINK_TRAIN_PRE_EMPHASIS_NONE (0<<22) |
| #define FDI_LINK_TRAIN_PRE_EMPHASIS_1_5X (1<<22) |
| #define FDI_LINK_TRAIN_PRE_EMPHASIS_2X (2<<22) |
| #define FDI_LINK_TRAIN_PRE_EMPHASIS_3X (3<<22) |
| /* ILK always use 400mV 0dB for voltage swing and pre-emphasis level. |
| SNB has different settings. */ |
| /* SNB A-stepping */ |
| #define FDI_LINK_TRAIN_400MV_0DB_SNB_A (0x38<<22) |
| #define FDI_LINK_TRAIN_400MV_6DB_SNB_A (0x02<<22) |
| #define FDI_LINK_TRAIN_600MV_3_5DB_SNB_A (0x01<<22) |
| #define FDI_LINK_TRAIN_800MV_0DB_SNB_A (0x0<<22) |
| /* SNB B-stepping */ |
| #define FDI_LINK_TRAIN_400MV_0DB_SNB_B (0x0<<22) |
| #define FDI_LINK_TRAIN_400MV_6DB_SNB_B (0x3a<<22) |
| #define FDI_LINK_TRAIN_600MV_3_5DB_SNB_B (0x39<<22) |
| #define FDI_LINK_TRAIN_800MV_0DB_SNB_B (0x38<<22) |
| #define FDI_LINK_TRAIN_VOL_EMP_MASK (0x3f<<22) |
| #define FDI_DP_PORT_WIDTH_X1 (0<<19) |
| #define FDI_DP_PORT_WIDTH_X2 (1<<19) |
| #define FDI_DP_PORT_WIDTH_X3 (2<<19) |
| #define FDI_DP_PORT_WIDTH_X4 (3<<19) |
| #define FDI_TX_ENHANCE_FRAME_ENABLE (1<<18) |
| /* Ironlake: hardwired to 1 */ |
| #define FDI_TX_PLL_ENABLE (1<<14) |
| |
| /* Ivybridge has different bits for lolz */ |
| #define FDI_LINK_TRAIN_PATTERN_1_IVB (0<<8) |
| #define FDI_LINK_TRAIN_PATTERN_2_IVB (1<<8) |
| #define FDI_LINK_TRAIN_PATTERN_IDLE_IVB (2<<8) |
| #define FDI_LINK_TRAIN_NONE_IVB (3<<8) |
| |
| /* both Tx and Rx */ |
| #define FDI_COMPOSITE_SYNC (1<<11) |
| #define FDI_LINK_TRAIN_AUTO (1<<10) |
| #define FDI_SCRAMBLING_ENABLE (0<<7) |
| #define FDI_SCRAMBLING_DISABLE (1<<7) |
| |
| /* FDI_RX, FDI_X is hard-wired to Transcoder_X */ |
| #define _FDI_RXA_CTL 0xf000c |
| #define _FDI_RXB_CTL 0xf100c |
| #define FDI_RX_CTL(pipe) _PIPE(pipe, _FDI_RXA_CTL, _FDI_RXB_CTL) |
| #define FDI_RX_ENABLE (1<<31) |
| /* train, dp width same as FDI_TX */ |
| #define FDI_FS_ERRC_ENABLE (1<<27) |
| #define FDI_FE_ERRC_ENABLE (1<<26) |
| #define FDI_DP_PORT_WIDTH_X8 (7<<19) |
| #define FDI_8BPC (0<<16) |
| #define FDI_10BPC (1<<16) |
| #define FDI_6BPC (2<<16) |
| #define FDI_12BPC (3<<16) |
| #define FDI_LINK_REVERSE_OVERWRITE (1<<15) |
| #define FDI_DMI_LINK_REVERSE_MASK (1<<14) |
| #define FDI_RX_PLL_ENABLE (1<<13) |
| #define FDI_FS_ERR_CORRECT_ENABLE (1<<11) |
| #define FDI_FE_ERR_CORRECT_ENABLE (1<<10) |
| #define FDI_FS_ERR_REPORT_ENABLE (1<<9) |
| #define FDI_FE_ERR_REPORT_ENABLE (1<<8) |
| #define FDI_RX_ENHANCE_FRAME_ENABLE (1<<6) |
| #define FDI_PCDCLK (1<<4) |
| /* CPT */ |
| #define FDI_AUTO_TRAINING (1<<10) |
| #define FDI_LINK_TRAIN_PATTERN_1_CPT (0<<8) |
| #define FDI_LINK_TRAIN_PATTERN_2_CPT (1<<8) |
| #define FDI_LINK_TRAIN_PATTERN_IDLE_CPT (2<<8) |
| #define FDI_LINK_TRAIN_NORMAL_CPT (3<<8) |
| #define FDI_LINK_TRAIN_PATTERN_MASK_CPT (3<<8) |
| /* LPT */ |
| #define FDI_PORT_WIDTH_2X_LPT (1<<19) |
| #define FDI_PORT_WIDTH_1X_LPT (0<<19) |
| |
| #define _FDI_RXA_MISC 0xf0010 |
| #define _FDI_RXB_MISC 0xf1010 |
| #define _FDI_RXA_TUSIZE1 0xf0030 |
| #define _FDI_RXA_TUSIZE2 0xf0038 |
| #define _FDI_RXB_TUSIZE1 0xf1030 |
| #define _FDI_RXB_TUSIZE2 0xf1038 |
| #define FDI_RX_TP1_TO_TP2_48 (2<<20) |
| #define FDI_RX_TP1_TO_TP2_64 (3<<20) |
| #define FDI_RX_FDI_DELAY_90 (0x90<<0) |
| #define FDI_RX_MISC(pipe) _PIPE(pipe, _FDI_RXA_MISC, _FDI_RXB_MISC) |
| #define FDI_RX_TUSIZE1(pipe) _PIPE(pipe, _FDI_RXA_TUSIZE1, _FDI_RXB_TUSIZE1) |
| #define FDI_RX_TUSIZE2(pipe) _PIPE(pipe, _FDI_RXA_TUSIZE2, _FDI_RXB_TUSIZE2) |
| |
| /* FDI_RX interrupt register format */ |
| #define FDI_RX_INTER_LANE_ALIGN (1<<10) |
| #define FDI_RX_SYMBOL_LOCK (1<<9) /* train 2 */ |
| #define FDI_RX_BIT_LOCK (1<<8) /* train 1 */ |
| #define FDI_RX_TRAIN_PATTERN_2_FAIL (1<<7) |
| #define FDI_RX_FS_CODE_ERR (1<<6) |
| #define FDI_RX_FE_CODE_ERR (1<<5) |
| #define FDI_RX_SYMBOL_ERR_RATE_ABOVE (1<<4) |
| #define FDI_RX_HDCP_LINK_FAIL (1<<3) |
| #define FDI_RX_PIXEL_FIFO_OVERFLOW (1<<2) |
| #define FDI_RX_CROSS_CLOCK_OVERFLOW (1<<1) |
| #define FDI_RX_SYMBOL_QUEUE_OVERFLOW (1<<0) |
| |
| #define _FDI_RXA_IIR 0xf0014 |
| #define _FDI_RXA_IMR 0xf0018 |
| #define _FDI_RXB_IIR 0xf1014 |
| #define _FDI_RXB_IMR 0xf1018 |
| #define FDI_RX_IIR(pipe) _PIPE(pipe, _FDI_RXA_IIR, _FDI_RXB_IIR) |
| #define FDI_RX_IMR(pipe) _PIPE(pipe, _FDI_RXA_IMR, _FDI_RXB_IMR) |
| |
| #define FDI_PLL_CTL_1 0xfe000 |
| #define FDI_PLL_CTL_2 0xfe004 |
| |
| /* or SDVOB */ |
| #define HDMIB 0xe1140 |
| #define PORT_ENABLE (1 << 31) |
| #define TRANSCODER(pipe) ((pipe) << 30) |
| #define TRANSCODER_CPT(pipe) ((pipe) << 29) |
| #define TRANSCODER_MASK (1 << 30) |
| #define TRANSCODER_MASK_CPT (3 << 29) |
| #define COLOR_FORMAT_8bpc (0) |
| #define COLOR_FORMAT_12bpc (3 << 26) |
| #define SDVOB_HOTPLUG_ENABLE (1 << 23) |
| #define SDVO_ENCODING (0) |
| #define TMDS_ENCODING (2 << 10) |
| #define NULL_PACKET_VSYNC_ENABLE (1 << 9) |
| /* CPT */ |
| #define HDMI_MODE_SELECT (1 << 9) |
| #define DVI_MODE_SELECT (0) |
| #define SDVOB_BORDER_ENABLE (1 << 7) |
| #define AUDIO_ENABLE (1 << 6) |
| #define VSYNC_ACTIVE_HIGH (1 << 4) |
| #define HSYNC_ACTIVE_HIGH (1 << 3) |
| #define PORT_DETECTED (1 << 2) |
| |
| /* PCH SDVOB multiplex with HDMIB */ |
| #define PCH_SDVOB HDMIB |
| |
| #define HDMIC 0xe1150 |
| #define HDMID 0xe1160 |
| |
| #define PCH_LVDS 0xe1180 |
| #define LVDS_DETECTED (1 << 1) |
| |
| /* vlv has 2 sets of panel control regs. */ |
| #define PIPEA_PP_STATUS 0x61200 |
| #define PIPEA_PP_CONTROL 0x61204 |
| #define PIPEA_PP_ON_DELAYS 0x61208 |
| #define PIPEA_PP_OFF_DELAYS 0x6120c |
| #define PIPEA_PP_DIVISOR 0x61210 |
| |
| #define PIPEB_PP_STATUS 0x61300 |
| #define PIPEB_PP_CONTROL 0x61304 |
| #define PIPEB_PP_ON_DELAYS 0x61308 |
| #define PIPEB_PP_OFF_DELAYS 0x6130c |
| #define PIPEB_PP_DIVISOR 0x61310 |
| |
| #define PCH_PP_STATUS 0xc7200 |
| #define PCH_PP_CONTROL 0xc7204 |
| #define PANEL_UNLOCK_REGS (0xabcd << 16) |
| #define PANEL_UNLOCK_MASK (0xffff << 16) |
| #define EDP_FORCE_VDD (1 << 3) |
| #define EDP_BLC_ENABLE (1 << 2) |
| #define PANEL_POWER_RESET (1 << 1) |
| #define PANEL_POWER_OFF (0 << 0) |
| #define PANEL_POWER_ON (1 << 0) |
| #define PCH_PP_ON_DELAYS 0xc7208 |
| #define PANEL_PORT_SELECT_MASK (3 << 30) |
| #define PANEL_PORT_SELECT_LVDS (0 << 30) |
| #define PANEL_PORT_SELECT_DPA (1 << 30) |
| #define EDP_PANEL (1 << 30) |
| #define PANEL_PORT_SELECT_DPC (2 << 30) |
| #define PANEL_PORT_SELECT_DPD (3 << 30) |
| #define PANEL_POWER_UP_DELAY_MASK (0x1fff0000) |
| #define PANEL_POWER_UP_DELAY_SHIFT 16 |
| #define PANEL_LIGHT_ON_DELAY_MASK (0x1fff) |
| #define PANEL_LIGHT_ON_DELAY_SHIFT 0 |
| |
| #define PCH_PP_OFF_DELAYS 0xc720c |
| #define PANEL_POWER_DOWN_DELAY_MASK (0x1fff0000) |
| #define PANEL_POWER_DOWN_DELAY_SHIFT 16 |
| #define PANEL_LIGHT_OFF_DELAY_MASK (0x1fff) |
| #define PANEL_LIGHT_OFF_DELAY_SHIFT 0 |
| |
| #define PCH_PP_DIVISOR 0xc7210 |
| #define PP_REFERENCE_DIVIDER_MASK (0xffffff00) |
| #define PP_REFERENCE_DIVIDER_SHIFT 8 |
| #define PANEL_POWER_CYCLE_DELAY_MASK (0x1f) |
| #define PANEL_POWER_CYCLE_DELAY_SHIFT 0 |
| |
| #define PCH_DP_B 0xe4100 |
| #define PCH_DPB_AUX_CH_CTL 0xe4110 |
| #define PCH_DPB_AUX_CH_DATA1 0xe4114 |
| #define PCH_DPB_AUX_CH_DATA2 0xe4118 |
| #define PCH_DPB_AUX_CH_DATA3 0xe411c |
| #define PCH_DPB_AUX_CH_DATA4 0xe4120 |
| #define PCH_DPB_AUX_CH_DATA5 0xe4124 |
| |
| #define PCH_DP_C 0xe4200 |
| #define PCH_DPC_AUX_CH_CTL 0xe4210 |
| #define PCH_DPC_AUX_CH_DATA1 0xe4214 |
| #define PCH_DPC_AUX_CH_DATA2 0xe4218 |
| #define PCH_DPC_AUX_CH_DATA3 0xe421c |
| #define PCH_DPC_AUX_CH_DATA4 0xe4220 |
| #define PCH_DPC_AUX_CH_DATA5 0xe4224 |
| |
| #define PCH_DP_D 0xe4300 |
| #define PCH_DPD_AUX_CH_CTL 0xe4310 |
| #define PCH_DPD_AUX_CH_DATA1 0xe4314 |
| #define PCH_DPD_AUX_CH_DATA2 0xe4318 |
| #define PCH_DPD_AUX_CH_DATA3 0xe431c |
| #define PCH_DPD_AUX_CH_DATA4 0xe4320 |
| #define PCH_DPD_AUX_CH_DATA5 0xe4324 |
| |
| /* CPT */ |
| #define PORT_TRANS_A_SEL_CPT 0 |
| #define PORT_TRANS_B_SEL_CPT (1<<29) |
| #define PORT_TRANS_C_SEL_CPT (2<<29) |
| #define PORT_TRANS_SEL_MASK (3<<29) |
| #define PORT_TRANS_SEL_CPT(pipe) ((pipe) << 29) |
| |
| #define TRANS_DP_CTL_A 0xe0300 |
| #define TRANS_DP_CTL_B 0xe1300 |
| #define TRANS_DP_CTL_C 0xe2300 |
| #define TRANS_DP_CTL(pipe) (TRANS_DP_CTL_A + (pipe) * 0x01000) |
| #define TRANS_DP_OUTPUT_ENABLE (1<<31) |
| #define TRANS_DP_PORT_SEL_B (0<<29) |
| #define TRANS_DP_PORT_SEL_C (1<<29) |
| #define TRANS_DP_PORT_SEL_D (2<<29) |
| #define TRANS_DP_PORT_SEL_NONE (3<<29) |
| #define TRANS_DP_PORT_SEL_MASK (3<<29) |
| #define TRANS_DP_AUDIO_ONLY (1<<26) |
| #define TRANS_DP_ENH_FRAMING (1<<18) |
| #define TRANS_DP_8BPC (0<<9) |
| #define TRANS_DP_10BPC (1<<9) |
| #define TRANS_DP_6BPC (2<<9) |
| #define TRANS_DP_12BPC (3<<9) |
| #define TRANS_DP_BPC_MASK (3<<9) |
| #define TRANS_DP_VSYNC_ACTIVE_HIGH (1<<4) |
| #define TRANS_DP_VSYNC_ACTIVE_LOW 0 |
| #define TRANS_DP_HSYNC_ACTIVE_HIGH (1<<3) |
| #define TRANS_DP_HSYNC_ACTIVE_LOW 0 |
| #define TRANS_DP_SYNC_MASK (3<<3) |
| |
| /* SNB eDP training params */ |
| /* SNB A-stepping */ |
| #define EDP_LINK_TRAIN_400MV_0DB_SNB_A (0x38<<22) |
| #define EDP_LINK_TRAIN_400MV_6DB_SNB_A (0x02<<22) |
| #define EDP_LINK_TRAIN_600MV_3_5DB_SNB_A (0x01<<22) |
| #define EDP_LINK_TRAIN_800MV_0DB_SNB_A (0x0<<22) |
| /* SNB B-stepping */ |
| #define EDP_LINK_TRAIN_400_600MV_0DB_SNB_B (0x0<<22) |
| #define EDP_LINK_TRAIN_400MV_3_5DB_SNB_B (0x1<<22) |
| #define EDP_LINK_TRAIN_400_600MV_6DB_SNB_B (0x3a<<22) |
| #define EDP_LINK_TRAIN_600_800MV_3_5DB_SNB_B (0x39<<22) |
| #define EDP_LINK_TRAIN_800_1200MV_0DB_SNB_B (0x38<<22) |
| #define EDP_LINK_TRAIN_VOL_EMP_MASK_SNB (0x3f<<22) |
| |
| /* IVB */ |
| #define EDP_LINK_TRAIN_400MV_0DB_IVB (0x24 <<22) |
| #define EDP_LINK_TRAIN_400MV_3_5DB_IVB (0x2a <<22) |
| #define EDP_LINK_TRAIN_400MV_6DB_IVB (0x2f <<22) |
| #define EDP_LINK_TRAIN_600MV_0DB_IVB (0x30 <<22) |
| #define EDP_LINK_TRAIN_600MV_3_5DB_IVB (0x36 <<22) |
| #define EDP_LINK_TRAIN_800MV_0DB_IVB (0x38 <<22) |
| #define EDP_LINK_TRAIN_800MV_3_5DB_IVB (0x33 <<22) |
| |
| /* legacy values */ |
| #define EDP_LINK_TRAIN_500MV_0DB_IVB (0x00 <<22) |
| #define EDP_LINK_TRAIN_1000MV_0DB_IVB (0x20 <<22) |
| #define EDP_LINK_TRAIN_500MV_3_5DB_IVB (0x02 <<22) |
| #define EDP_LINK_TRAIN_1000MV_3_5DB_IVB (0x22 <<22) |
| #define EDP_LINK_TRAIN_1000MV_6DB_IVB (0x23 <<22) |
| |
| #define EDP_LINK_TRAIN_VOL_EMP_MASK_IVB (0x3f<<22) |
| |
| #define FORCEWAKE 0xA18C |
| #define FORCEWAKE_VLV 0x1300b0 |
| #define FORCEWAKE_ACK_VLV 0x1300b4 |
| #define FORCEWAKE_ACK_HSW 0x130044 |
| #define FORCEWAKE_ACK 0x130090 |
| #define FORCEWAKE_MT 0xa188 /* multi-threaded */ |
| #define FORCEWAKE_MT_ACK 0x130040 |
| #define ECOBUS 0xa180 |
| #define FORCEWAKE_MT_ENABLE (1<<5) |
| |
| #define GTFIFODBG 0x120000 |
| #define GT_FIFO_CPU_ERROR_MASK 7 |
| #define GT_FIFO_OVFERR (1<<2) |
| #define GT_FIFO_IAWRERR (1<<1) |
| #define GT_FIFO_IARDERR (1<<0) |
| |
| #define GT_FIFO_FREE_ENTRIES 0x120008 |
| #define GT_FIFO_NUM_RESERVED_ENTRIES 20 |
| |
| #define GEN6_UCGCTL1 0x9400 |
| # define GEN6_BLBUNIT_CLOCK_GATE_DISABLE (1 << 5) |
| # define GEN6_CSUNIT_CLOCK_GATE_DISABLE (1 << 7) |
| |
| #define GEN6_UCGCTL2 0x9404 |
| # define GEN7_VDSUNIT_CLOCK_GATE_DISABLE (1 << 30) |
| # define GEN7_TDLUNIT_CLOCK_GATE_DISABLE (1 << 22) |
| # define GEN6_RCZUNIT_CLOCK_GATE_DISABLE (1 << 13) |
| # define GEN6_RCPBUNIT_CLOCK_GATE_DISABLE (1 << 12) |
| # define GEN6_RCCUNIT_CLOCK_GATE_DISABLE (1 << 11) |
| |
| #define GEN7_UCGCTL4 0x940c |
| #define GEN7_L3BANK2X_CLOCK_GATE_DISABLE (1<<25) |
| |
| #define GEN6_RPNSWREQ 0xA008 |
| #define GEN6_TURBO_DISABLE (1<<31) |
| #define GEN6_FREQUENCY(x) ((x)<<25) |
| #define GEN6_OFFSET(x) ((x)<<19) |
| #define GEN6_AGGRESSIVE_TURBO (0<<15) |
| #define GEN6_RC_VIDEO_FREQ 0xA00C |
| #define GEN6_RC_CONTROL 0xA090 |
| #define GEN6_RC_CTL_RC6pp_ENABLE (1<<16) |
| #define GEN6_RC_CTL_RC6p_ENABLE (1<<17) |
| #define GEN6_RC_CTL_RC6_ENABLE (1<<18) |
| #define GEN6_RC_CTL_RC1e_ENABLE (1<<20) |
| #define GEN6_RC_CTL_RC7_ENABLE (1<<22) |
| #define GEN6_RC_CTL_EI_MODE(x) ((x)<<27) |
| #define GEN6_RC_CTL_HW_ENABLE (1<<31) |
| #define GEN6_RP_DOWN_TIMEOUT 0xA010 |
| #define GEN6_RP_INTERRUPT_LIMITS 0xA014 |
| #define GEN6_RPSTAT1 0xA01C |
| #define GEN6_CAGF_SHIFT 8 |
| #define GEN6_CAGF_MASK (0x7f << GEN6_CAGF_SHIFT) |
| #define GEN6_RP_CONTROL 0xA024 |
| #define GEN6_RP_MEDIA_TURBO (1<<11) |
| #define GEN6_RP_MEDIA_MODE_MASK (3<<9) |
| #define GEN6_RP_MEDIA_HW_TURBO_MODE (3<<9) |
| #define GEN6_RP_MEDIA_HW_NORMAL_MODE (2<<9) |
| #define GEN6_RP_MEDIA_HW_MODE (1<<9) |
| #define GEN6_RP_MEDIA_SW_MODE (0<<9) |
| #define GEN6_RP_MEDIA_IS_GFX (1<<8) |
| #define GEN6_RP_ENABLE (1<<7) |
| #define GEN6_RP_UP_IDLE_MIN (0x1<<3) |
| #define GEN6_RP_UP_BUSY_AVG (0x2<<3) |
| #define GEN6_RP_UP_BUSY_CONT (0x4<<3) |
| #define GEN7_RP_DOWN_IDLE_AVG (0x2<<0) |
| #define GEN6_RP_DOWN_IDLE_CONT (0x1<<0) |
| #define GEN6_RP_UP_THRESHOLD 0xA02C |
| #define GEN6_RP_DOWN_THRESHOLD 0xA030 |
| #define GEN6_RP_CUR_UP_EI 0xA050 |
| #define GEN6_CURICONT_MASK 0xffffff |
| #define GEN6_RP_CUR_UP 0xA054 |
| #define GEN6_CURBSYTAVG_MASK 0xffffff |
| #define GEN6_RP_PREV_UP 0xA058 |
| #define GEN6_RP_CUR_DOWN_EI 0xA05C |
| #define GEN6_CURIAVG_MASK 0xffffff |
| #define GEN6_RP_CUR_DOWN 0xA060 |
| #define GEN6_RP_PREV_DOWN 0xA064 |
| #define GEN6_RP_UP_EI 0xA068 |
| #define GEN6_RP_DOWN_EI 0xA06C |
| #define GEN6_RP_IDLE_HYSTERSIS 0xA070 |
| #define GEN6_RC_STATE 0xA094 |
| #define GEN6_RC1_WAKE_RATE_LIMIT 0xA098 |
| #define GEN6_RC6_WAKE_RATE_LIMIT 0xA09C |
| #define GEN6_RC6pp_WAKE_RATE_LIMIT 0xA0A0 |
| #define GEN6_RC_EVALUATION_INTERVAL 0xA0A8 |
| #define GEN6_RC_IDLE_HYSTERSIS 0xA0AC |
| #define GEN6_RC_SLEEP 0xA0B0 |
| #define GEN6_RC1e_THRESHOLD 0xA0B4 |
| #define GEN6_RC6_THRESHOLD 0xA0B8 |
| #define GEN6_RC6p_THRESHOLD 0xA0BC |
| #define GEN6_RC6pp_THRESHOLD 0xA0C0 |
| #define GEN6_PMINTRMSK 0xA168 |
| |
| #define GEN6_PMISR 0x44020 |
| #define GEN6_PMIMR 0x44024 /* rps_lock */ |
| #define GEN6_PMIIR 0x44028 |
| #define GEN6_PMIER 0x4402C |
| #define GEN6_PM_MBOX_EVENT (1<<25) |
| #define GEN6_PM_THERMAL_EVENT (1<<24) |
| #define GEN6_PM_RP_DOWN_TIMEOUT (1<<6) |
| #define GEN6_PM_RP_UP_THRESHOLD (1<<5) |
| #define GEN6_PM_RP_DOWN_THRESHOLD (1<<4) |
| #define GEN6_PM_RP_UP_EI_EXPIRED (1<<2) |
| #define GEN6_PM_RP_DOWN_EI_EXPIRED (1<<1) |
| #define GEN6_PM_DEFERRED_EVENTS (GEN6_PM_RP_UP_THRESHOLD | \ |
| GEN6_PM_RP_DOWN_THRESHOLD | \ |
| GEN6_PM_RP_DOWN_TIMEOUT) |
| |
| #define GEN6_GT_GFX_RC6_LOCKED 0x138104 |
| #define GEN6_GT_GFX_RC6 0x138108 |
| #define GEN6_GT_GFX_RC6p 0x13810C |
| #define GEN6_GT_GFX_RC6pp 0x138110 |
| |
| #define GEN6_PCODE_MAILBOX 0x138124 |
| #define GEN6_PCODE_READY (1<<31) |
| #define GEN6_READ_OC_PARAMS 0xc |
| #define GEN6_PCODE_WRITE_MIN_FREQ_TABLE 0x8 |
| #define GEN6_PCODE_READ_MIN_FREQ_TABLE 0x9 |
| #define GEN6_PCODE_DATA 0x138128 |
| #define GEN6_PCODE_FREQ_IA_RATIO_SHIFT 8 |
| |
| #define GEN6_GT_CORE_STATUS 0x138060 |
| #define GEN6_CORE_CPD_STATE_MASK (7<<4) |
| #define GEN6_RCn_MASK 7 |
| #define GEN6_RC0 0 |
| #define GEN6_RC3 2 |
| #define GEN6_RC6 3 |
| #define GEN6_RC7 4 |
| |
| #define GEN7_MISCCPCTL (0x9424) |
| #define GEN7_DOP_CLOCK_GATE_ENABLE (1<<0) |
| |
| /* IVYBRIDGE DPF */ |
| #define GEN7_L3CDERRST1 0xB008 /* L3CD Error Status 1 */ |
| #define GEN7_L3CDERRST1_ROW_MASK (0x7ff<<14) |
| #define GEN7_PARITY_ERROR_VALID (1<<13) |
| #define GEN7_L3CDERRST1_BANK_MASK (3<<11) |
| #define GEN7_L3CDERRST1_SUBBANK_MASK (7<<8) |
| #define GEN7_PARITY_ERROR_ROW(reg) \ |
| ((reg & GEN7_L3CDERRST1_ROW_MASK) >> 14) |
| #define GEN7_PARITY_ERROR_BANK(reg) \ |
| ((reg & GEN7_L3CDERRST1_BANK_MASK) >> 11) |
| #define GEN7_PARITY_ERROR_SUBBANK(reg) \ |
| ((reg & GEN7_L3CDERRST1_SUBBANK_MASK) >> 8) |
| #define GEN7_L3CDERRST1_ENABLE (1<<7) |
| |
| #define GEN7_L3LOG_BASE 0xB070 |
| #define GEN7_L3LOG_SIZE 0x80 |
| |
| #define G4X_AUD_VID_DID 0x62020 |
| #define INTEL_AUDIO_DEVCL 0x808629FB |
| #define INTEL_AUDIO_DEVBLC 0x80862801 |
| #define INTEL_AUDIO_DEVCTG 0x80862802 |
| |
| #define G4X_AUD_CNTL_ST 0x620B4 |
| #define G4X_ELDV_DEVCL_DEVBLC (1 << 13) |
| #define G4X_ELDV_DEVCTG (1 << 14) |
| #define G4X_ELD_ADDR (0xf << 5) |
| #define G4X_ELD_ACK (1 << 4) |
| #define G4X_HDMIW_HDMIEDID 0x6210C |
| |
| #define IBX_HDMIW_HDMIEDID_A 0xE2050 |
| #define IBX_HDMIW_HDMIEDID_B 0xE2150 |
| #define IBX_HDMIW_HDMIEDID(pipe) _PIPE(pipe, \ |
| IBX_HDMIW_HDMIEDID_A, \ |
| IBX_HDMIW_HDMIEDID_B) |
| #define IBX_AUD_CNTL_ST_A 0xE20B4 |
| #define IBX_AUD_CNTL_ST_B 0xE21B4 |
| #define IBX_AUD_CNTL_ST(pipe) _PIPE(pipe, \ |
| IBX_AUD_CNTL_ST_A, \ |
| IBX_AUD_CNTL_ST_B) |
| #define IBX_ELD_BUFFER_SIZE (0x1f << 10) |
| #define IBX_ELD_ADDRESS (0x1f << 5) |
| #define IBX_ELD_ACK (1 << 4) |
| #define IBX_AUD_CNTL_ST2 0xE20C0 |
| #define IBX_ELD_VALIDB (1 << 0) |
| #define IBX_CP_READYB (1 << 1) |
| |
| #define CPT_HDMIW_HDMIEDID_A 0xE5050 |
| #define CPT_HDMIW_HDMIEDID_B 0xE5150 |
| #define CPT_HDMIW_HDMIEDID(pipe) _PIPE(pipe, \ |
| CPT_HDMIW_HDMIEDID_A, \ |
| CPT_HDMIW_HDMIEDID_B) |
| #define CPT_AUD_CNTL_ST_A 0xE50B4 |
| #define CPT_AUD_CNTL_ST_B 0xE51B4 |
| #define CPT_AUD_CNTL_ST(pipe) _PIPE(pipe, \ |
| CPT_AUD_CNTL_ST_A, \ |
| CPT_AUD_CNTL_ST_B) |
| #define CPT_AUD_CNTRL_ST2 0xE50C0 |
| |
| /* These are the 4 32-bit write offset registers for each stream |
| * output buffer. It determines the offset from the |
| * 3DSTATE_SO_BUFFERs that the next streamed vertex output goes to. |
| */ |
| #define GEN7_SO_WRITE_OFFSET(n) (0x5280 + (n) * 4) |
| |
| #define IBX_AUD_CONFIG_A 0xe2000 |
| #define IBX_AUD_CONFIG_B 0xe2100 |
| #define IBX_AUD_CFG(pipe) _PIPE(pipe, \ |
| IBX_AUD_CONFIG_A, \ |
| IBX_AUD_CONFIG_B) |
| #define CPT_AUD_CONFIG_A 0xe5000 |
| #define CPT_AUD_CONFIG_B 0xe5100 |
| #define CPT_AUD_CFG(pipe) _PIPE(pipe, \ |
| CPT_AUD_CONFIG_A, \ |
| CPT_AUD_CONFIG_B) |
| #define AUD_CONFIG_N_VALUE_INDEX (1 << 29) |
| #define AUD_CONFIG_N_PROG_ENABLE (1 << 28) |
| #define AUD_CONFIG_UPPER_N_SHIFT 20 |
| #define AUD_CONFIG_UPPER_N_VALUE (0xff << 20) |
| #define AUD_CONFIG_LOWER_N_SHIFT 4 |
| #define AUD_CONFIG_LOWER_N_VALUE (0xfff << 4) |
| #define AUD_CONFIG_PIXEL_CLOCK_HDMI_SHIFT 16 |
| #define AUD_CONFIG_PIXEL_CLOCK_HDMI (0xf << 16) |
| #define AUD_CONFIG_DISABLE_NCTS (1 << 3) |
| |
| /* HSW Audio */ |
| #define HSW_AUD_CONFIG_A 0x65000 /* Audio Configuration Transcoder A */ |
| #define HSW_AUD_CONFIG_B 0x65100 /* Audio Configuration Transcoder B */ |
| #define HSW_AUD_CFG(pipe) _PIPE(pipe, \ |
| HSW_AUD_CONFIG_A, \ |
| HSW_AUD_CONFIG_B) |
| |
| #define HSW_AUD_MISC_CTRL_A 0x65010 /* Audio Misc Control Convert 1 */ |
| #define HSW_AUD_MISC_CTRL_B 0x65110 /* Audio Misc Control Convert 2 */ |
| #define HSW_AUD_MISC_CTRL(pipe) _PIPE(pipe, \ |
| HSW_AUD_MISC_CTRL_A, \ |
| HSW_AUD_MISC_CTRL_B) |
| |
| #define HSW_AUD_DIP_ELD_CTRL_ST_A 0x650b4 /* Audio DIP and ELD Control State Transcoder A */ |
| #define HSW_AUD_DIP_ELD_CTRL_ST_B 0x651b4 /* Audio DIP and ELD Control State Transcoder B */ |
| #define HSW_AUD_DIP_ELD_CTRL(pipe) _PIPE(pipe, \ |
| HSW_AUD_DIP_ELD_CTRL_ST_A, \ |
| HSW_AUD_DIP_ELD_CTRL_ST_B) |
| |
| /* Audio Digital Converter */ |
| #define HSW_AUD_DIG_CNVT_1 0x65080 /* Audio Converter 1 */ |
| #define HSW_AUD_DIG_CNVT_2 0x65180 /* Audio Converter 1 */ |
| #define AUD_DIG_CNVT(pipe) _PIPE(pipe, \ |
| HSW_AUD_DIG_CNVT_1, \ |
| HSW_AUD_DIG_CNVT_2) |
| #define DIP_PORT_SEL_MASK 0x3 |
| |
| #define HSW_AUD_EDID_DATA_A 0x65050 |
| #define HSW_AUD_EDID_DATA_B 0x65150 |
| #define HSW_AUD_EDID_DATA(pipe) _PIPE(pipe, \ |
| HSW_AUD_EDID_DATA_A, \ |
| HSW_AUD_EDID_DATA_B) |
| |
| #define HSW_AUD_PIPE_CONV_CFG 0x6507c /* Audio pipe and converter configs */ |
| #define HSW_AUD_PIN_ELD_CP_VLD 0x650c0 /* Audio ELD and CP Ready Status */ |
| #define AUDIO_INACTIVE_C (1<<11) |
| #define AUDIO_INACTIVE_B (1<<7) |
| #define AUDIO_INACTIVE_A (1<<3) |
| #define AUDIO_OUTPUT_ENABLE_A (1<<2) |
| #define AUDIO_OUTPUT_ENABLE_B (1<<6) |
| #define AUDIO_OUTPUT_ENABLE_C (1<<10) |
| #define AUDIO_ELD_VALID_A (1<<0) |
| #define AUDIO_ELD_VALID_B (1<<4) |
| #define AUDIO_ELD_VALID_C (1<<8) |
| #define AUDIO_CP_READY_A (1<<1) |
| #define AUDIO_CP_READY_B (1<<5) |
| #define AUDIO_CP_READY_C (1<<9) |
| |
| /* HSW Power Wells */ |
| #define HSW_PWR_WELL_CTL1 0x45400 /* BIOS */ |
| #define HSW_PWR_WELL_CTL2 0x45404 /* Driver */ |
| #define HSW_PWR_WELL_CTL3 0x45408 /* KVMR */ |
| #define HSW_PWR_WELL_CTL4 0x4540C /* Debug */ |
| #define HSW_PWR_WELL_ENABLE (1<<31) |
| #define HSW_PWR_WELL_STATE (1<<30) |
| #define HSW_PWR_WELL_CTL5 0x45410 |
| #define HSW_PWR_WELL_ENABLE_SINGLE_STEP (1<<31) |
| #define HSW_PWR_WELL_PWR_GATE_OVERRIDE (1<<20) |
| #define HSW_PWR_WELL_FORCE_ON (1<<19) |
| #define HSW_PWR_WELL_CTL6 0x45414 |
| |
| /* Per-pipe DDI Function Control */ |
| #define PIPE_DDI_FUNC_CTL_A 0x60400 |
| #define PIPE_DDI_FUNC_CTL_B 0x61400 |
| #define PIPE_DDI_FUNC_CTL_C 0x62400 |
| #define PIPE_DDI_FUNC_CTL_EDP 0x6F400 |
| #define DDI_FUNC_CTL(pipe) _PIPE(pipe, PIPE_DDI_FUNC_CTL_A, \ |
| PIPE_DDI_FUNC_CTL_B) |
| #define PIPE_DDI_FUNC_ENABLE (1<<31) |
| /* Those bits are ignored by pipe EDP since it can only connect to DDI A */ |
| #define PIPE_DDI_PORT_MASK (7<<28) |
| #define PIPE_DDI_SELECT_PORT(x) ((x)<<28) |
| #define PIPE_DDI_MODE_SELECT_MASK (7<<24) |
| #define PIPE_DDI_MODE_SELECT_HDMI (0<<24) |
| #define PIPE_DDI_MODE_SELECT_DVI (1<<24) |
| #define PIPE_DDI_MODE_SELECT_DP_SST (2<<24) |
| #define PIPE_DDI_MODE_SELECT_DP_MST (3<<24) |
| #define PIPE_DDI_MODE_SELECT_FDI (4<<24) |
| #define PIPE_DDI_BPC_MASK (7<<20) |
| #define PIPE_DDI_BPC_8 (0<<20) |
| #define PIPE_DDI_BPC_10 (1<<20) |
| #define PIPE_DDI_BPC_6 (2<<20) |
| #define PIPE_DDI_BPC_12 (3<<20) |
| #define PIPE_DDI_PVSYNC (1<<17) |
| #define PIPE_DDI_PHSYNC (1<<16) |
| #define PIPE_DDI_BFI_ENABLE (1<<4) |
| #define PIPE_DDI_PORT_WIDTH_X1 (0<<1) |
| #define PIPE_DDI_PORT_WIDTH_X2 (1<<1) |
| #define PIPE_DDI_PORT_WIDTH_X4 (3<<1) |
| |
| /* DisplayPort Transport Control */ |
| #define DP_TP_CTL_A 0x64040 |
| #define DP_TP_CTL_B 0x64140 |
| #define DP_TP_CTL(port) _PORT(port, DP_TP_CTL_A, DP_TP_CTL_B) |
| #define DP_TP_CTL_ENABLE (1<<31) |
| #define DP_TP_CTL_MODE_SST (0<<27) |
| #define DP_TP_CTL_MODE_MST (1<<27) |
| #define DP_TP_CTL_ENHANCED_FRAME_ENABLE (1<<18) |
| #define DP_TP_CTL_FDI_AUTOTRAIN (1<<15) |
| #define DP_TP_CTL_LINK_TRAIN_MASK (7<<8) |
| #define DP_TP_CTL_LINK_TRAIN_PAT1 (0<<8) |
| #define DP_TP_CTL_LINK_TRAIN_PAT2 (1<<8) |
| #define DP_TP_CTL_LINK_TRAIN_NORMAL (3<<8) |
| |
| /* DisplayPort Transport Status */ |
| #define DP_TP_STATUS_A 0x64044 |
| #define DP_TP_STATUS_B 0x64144 |
| #define DP_TP_STATUS(port) _PORT(port, DP_TP_STATUS_A, DP_TP_STATUS_B) |
| #define DP_TP_STATUS_AUTOTRAIN_DONE (1<<12) |
| |
| /* DDI Buffer Control */ |
| #define DDI_BUF_CTL_A 0x64000 |
| #define DDI_BUF_CTL_B 0x64100 |
| #define DDI_BUF_CTL(port) _PORT(port, DDI_BUF_CTL_A, DDI_BUF_CTL_B) |
| #define DDI_BUF_CTL_ENABLE (1<<31) |
| #define DDI_BUF_EMP_400MV_0DB_HSW (0<<24) /* Sel0 */ |
| #define DDI_BUF_EMP_400MV_3_5DB_HSW (1<<24) /* Sel1 */ |
| #define DDI_BUF_EMP_400MV_6DB_HSW (2<<24) /* Sel2 */ |
| #define DDI_BUF_EMP_400MV_9_5DB_HSW (3<<24) /* Sel3 */ |
| #define DDI_BUF_EMP_600MV_0DB_HSW (4<<24) /* Sel4 */ |
| #define DDI_BUF_EMP_600MV_3_5DB_HSW (5<<24) /* Sel5 */ |
| #define DDI_BUF_EMP_600MV_6DB_HSW (6<<24) /* Sel6 */ |
| #define DDI_BUF_EMP_800MV_0DB_HSW (7<<24) /* Sel7 */ |
| #define DDI_BUF_EMP_800MV_3_5DB_HSW (8<<24) /* Sel8 */ |
| #define DDI_BUF_EMP_MASK (0xf<<24) |
| #define DDI_BUF_IS_IDLE (1<<7) |
| #define DDI_PORT_WIDTH_X1 (0<<1) |
| #define DDI_PORT_WIDTH_X2 (1<<1) |
| #define DDI_PORT_WIDTH_X4 (3<<1) |
| #define DDI_INIT_DISPLAY_DETECTED (1<<0) |
| |
| /* DDI Buffer Translations */ |
| #define DDI_BUF_TRANS_A 0x64E00 |
| #define DDI_BUF_TRANS_B 0x64E60 |
| #define DDI_BUF_TRANS(port) _PORT(port, DDI_BUF_TRANS_A, DDI_BUF_TRANS_B) |
| |
| /* Sideband Interface (SBI) is programmed indirectly, via |
| * SBI_ADDR, which contains the register offset; and SBI_DATA, |
| * which contains the payload */ |
| #define SBI_ADDR 0xC6000 |
| #define SBI_DATA 0xC6004 |
| #define SBI_CTL_STAT 0xC6008 |
| #define SBI_CTL_OP_CRRD (0x6<<8) |
| #define SBI_CTL_OP_CRWR (0x7<<8) |
| #define SBI_RESPONSE_FAIL (0x1<<1) |
| #define SBI_RESPONSE_SUCCESS (0x0<<1) |
| #define SBI_BUSY (0x1<<0) |
| #define SBI_READY (0x0<<0) |
| |
| /* SBI offsets */ |
| #define SBI_SSCDIVINTPHASE6 0x0600 |
| #define SBI_SSCDIVINTPHASE_DIVSEL_MASK ((0x7f)<<1) |
| #define SBI_SSCDIVINTPHASE_DIVSEL(x) ((x)<<1) |
| #define SBI_SSCDIVINTPHASE_INCVAL_MASK ((0x7f)<<8) |
| #define SBI_SSCDIVINTPHASE_INCVAL(x) ((x)<<8) |
| #define SBI_SSCDIVINTPHASE_DIR(x) ((x)<<15) |
| #define SBI_SSCDIVINTPHASE_PROPAGATE (1<<0) |
| #define SBI_SSCCTL 0x020c |
| #define SBI_SSCCTL6 0x060C |
| #define SBI_SSCCTL_DISABLE (1<<0) |
| #define SBI_SSCAUXDIV6 0x0610 |
| #define SBI_SSCAUXDIV_FINALDIV2SEL(x) ((x)<<4) |
| #define SBI_DBUFF0 0x2a00 |
| |
| /* LPT PIXCLK_GATE */ |
| #define PIXCLK_GATE 0xC6020 |
| #define PIXCLK_GATE_UNGATE (1<<0) |
| #define PIXCLK_GATE_GATE (0<<0) |
| |
| /* SPLL */ |
| #define SPLL_CTL 0x46020 |
| #define SPLL_PLL_ENABLE (1<<31) |
| #define SPLL_PLL_SCC (1<<28) |
| #define SPLL_PLL_NON_SCC (2<<28) |
| #define SPLL_PLL_FREQ_810MHz (0<<26) |
| #define SPLL_PLL_FREQ_1350MHz (1<<26) |
| |
| /* WRPLL */ |
| #define WRPLL_CTL1 0x46040 |
| #define WRPLL_CTL2 0x46060 |
| #define WRPLL_PLL_ENABLE (1<<31) |
| #define WRPLL_PLL_SELECT_SSC (0x01<<28) |
| #define WRPLL_PLL_SELECT_NON_SCC (0x02<<28) |
| #define WRPLL_PLL_SELECT_LCPLL_2700 (0x03<<28) |
| /* WRPLL divider programming */ |
| #define WRPLL_DIVIDER_REFERENCE(x) ((x)<<0) |
| #define WRPLL_DIVIDER_POST(x) ((x)<<8) |
| #define WRPLL_DIVIDER_FEEDBACK(x) ((x)<<16) |
| |
| /* Port clock selection */ |
| #define PORT_CLK_SEL_A 0x46100 |
| #define PORT_CLK_SEL_B 0x46104 |
| #define PORT_CLK_SEL(port) _PORT(port, PORT_CLK_SEL_A, PORT_CLK_SEL_B) |
| #define PORT_CLK_SEL_LCPLL_2700 (0<<29) |
| #define PORT_CLK_SEL_LCPLL_1350 (1<<29) |
| #define PORT_CLK_SEL_LCPLL_810 (2<<29) |
| #define PORT_CLK_SEL_SPLL (3<<29) |
| #define PORT_CLK_SEL_WRPLL1 (4<<29) |
| #define PORT_CLK_SEL_WRPLL2 (5<<29) |
| |
| /* Pipe clock selection */ |
| #define PIPE_CLK_SEL_A 0x46140 |
| #define PIPE_CLK_SEL_B 0x46144 |
| #define PIPE_CLK_SEL(pipe) _PIPE(pipe, PIPE_CLK_SEL_A, PIPE_CLK_SEL_B) |
| /* For each pipe, we need to select the corresponding port clock */ |
| #define PIPE_CLK_SEL_DISABLED (0x0<<29) |
| #define PIPE_CLK_SEL_PORT(x) ((x+1)<<29) |
| |
| /* LCPLL Control */ |
| #define LCPLL_CTL 0x130040 |
| #define LCPLL_PLL_DISABLE (1<<31) |
| #define LCPLL_PLL_LOCK (1<<30) |
| #define LCPLL_CD_CLOCK_DISABLE (1<<25) |
| #define LCPLL_CD2X_CLOCK_DISABLE (1<<23) |
| |
| /* Pipe WM_LINETIME - watermark line time */ |
| #define PIPE_WM_LINETIME_A 0x45270 |
| #define PIPE_WM_LINETIME_B 0x45274 |
| #define PIPE_WM_LINETIME(pipe) _PIPE(pipe, PIPE_WM_LINETIME_A, \ |
| PIPE_WM_LINETIME_B) |
| #define PIPE_WM_LINETIME_MASK (0x1ff) |
| #define PIPE_WM_LINETIME_TIME(x) ((x)) |
| #define PIPE_WM_LINETIME_IPS_LINETIME_MASK (0x1ff<<16) |
| #define PIPE_WM_LINETIME_IPS_LINETIME(x) ((x)<<16) |
| |
| /* SFUSE_STRAP */ |
| #define SFUSE_STRAP 0xc2014 |
| #define SFUSE_STRAP_DDIB_DETECTED (1<<2) |
| #define SFUSE_STRAP_DDIC_DETECTED (1<<1) |
| #define SFUSE_STRAP_DDID_DETECTED (1<<0) |
| |
| #define WM_DBG 0x45280 |
| #define WM_DBG_DISALLOW_MULTIPLE_LP (1<<0) |
| #define WM_DBG_DISALLOW_MAXFIFO (1<<1) |
| #define WM_DBG_DISALLOW_SPRITE (1<<2) |
| |
| #endif /* _I915_REG_H_ */ |