ARM: pxa: Push Colibri evalboard MFP into module files
This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.
(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
diff --git a/arch/arm/mach-pxa/colibri-pxa270-evalboard.c b/arch/arm/mach-pxa/colibri-pxa270-evalboard.c
index 6177ff5..e1a2b52 100644
--- a/arch/arm/mach-pxa/colibri-pxa270-evalboard.c
+++ b/arch/arm/mach-pxa/colibri-pxa270-evalboard.c
@@ -30,61 +30,28 @@
#include "devices.h"
/******************************************************************************
- * Pin configuration
- ******************************************************************************/
-static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {
- /* MMC */
- GPIO32_MMC_CLK,
- GPIO92_MMC_DAT_0,
- GPIO109_MMC_DAT_1,
- GPIO110_MMC_DAT_2,
- GPIO111_MMC_DAT_3,
- GPIO112_MMC_CMD,
- GPIO0_GPIO, /* SD detect */
-
- /* FFUART */
- GPIO39_FFUART_TXD,
- GPIO34_FFUART_RXD,
-
- /* UHC */
- GPIO88_USBH1_PWR,
- GPIO89_USBH1_PEN,
- GPIO119_USBH2_PWR,
- GPIO120_USBH2_PEN,
-
- /* PCMCIA */
- GPIO85_nPCE_1,
- GPIO54_nPCE_2,
- GPIO55_nPREG,
- GPIO50_nPIOR,
- GPIO51_nPIOW,
- GPIO49_nPWE,
- GPIO48_nPOE,
- GPIO57_nIOIS16,
- GPIO56_nPWAIT,
- GPIO104_PSKTSEL,
- GPIO53_GPIO, /* RESET */
- GPIO83_GPIO, /* BVD1 */
- GPIO82_GPIO, /* BVD2 */
- GPIO1_GPIO, /* READY */
- GPIO84_GPIO, /* DETECT */
- GPIO107_GPIO, /* PPEN */
-};
-
-/******************************************************************************
* SD/MMC card controller
******************************************************************************/
#if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
static struct pxamci_platform_data colibri_pxa270_mci_platform_data = {
.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
.gpio_power = -1,
- .gpio_card_detect = GPIO0_COLIBRI_PXA270_SD_DETECT,
.gpio_card_ro = -1,
.detect_delay_ms = 200,
};
static void __init colibri_pxa270_mmc_init(void)
{
+ if (machine_is_colibri()) /* PXA270 Colibri */
+ colibri_pxa270_mci_platform_data.gpio_card_detect =
+ GPIO0_COLIBRI_PXA270_SD_DETECT;
+ if (machine_is_colibri300()) /* PXA300 Colibri */
+ colibri_pxa270_mci_platform_data.gpio_card_detect =
+ GPIO39_COLIBRI_PXA300_SD_DETECT;
+ else /* PXA320 Colibri */
+ colibri_pxa270_mci_platform_data.gpio_card_detect =
+ GPIO28_COLIBRI_PXA320_SD_DETECT;
+
pxa_set_mci_info(&colibri_pxa270_mci_platform_data);
}
#else
@@ -103,13 +70,17 @@
static struct pxaohci_platform_data colibri_pxa270_ohci_info = {
.port_mode = PMM_PERPORT_MODE,
- .flags = ENABLE_PORT1 | ENABLE_PORT2 |
+ .flags = ENABLE_PORT1 |
POWER_CONTROL_LOW | POWER_SENSE_LOW,
.init = colibri_pxa270_ohci_init,
};
static void __init colibri_pxa270_uhc_init(void)
{
+ /* Colibri PXA270 has two usb ports, TBA for 320 */
+ if (machine_is_colibri())
+ colibri_pxa270_ohci_info.flags |= ENABLE_PORT2;
+
pxa_set_ohci_info(&colibri_pxa270_ohci_info);
}
#else
@@ -118,7 +89,6 @@
void __init colibri_pxa270_evalboard_init(void)
{
- pxa2xx_mfp_config(ARRAY_AND_SIZE(colibri_pxa270_evalboard_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
@@ -126,4 +96,3 @@
colibri_pxa270_mmc_init();
colibri_pxa270_uhc_init();
}
-