atari_NCR5380: Remove RESET_BOOT, CONFIG_ATARI_SCSI_TOSHIBA_DELAY and CONFIG_ATARI_SCSI_RESET_BOOT
The atari_NCR5380.c core driver now takes care of bus reset upon driver
initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM
support into the core driver, enabled with a host flag, so that all
NCR5380 drivers can make use of it.
Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and
ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant.
Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and
sun3_scsi_reset_boot() routines. None of this duplicated code is needed
now that all drivers can use NCR5380_maybe_reset_bus().
This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the
other NCR5380 drivers.
The bus reset may raise an interrupt. That would be new behaviour for
atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt
is not assigned to atari_scsi at this stage, so
CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already.
Regardless, do_reset() now raises and clears the interrupt within
local_irq_save/restore which should avoid problems.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
diff --git a/drivers/scsi/atari_NCR5380.c b/drivers/scsi/atari_NCR5380.c
index a15b655..de53cda 100644
--- a/drivers/scsi/atari_NCR5380.c
+++ b/drivers/scsi/atari_NCR5380.c
@@ -674,13 +674,14 @@
"base 0x%lx, irq %d, "
"can_queue %d, cmd_per_lun %d, "
"sg_tablesize %d, this_id %d, "
- "flags { %s}, "
+ "flags { %s%s}, "
"options { %s} ",
instance->hostt->name, instance->io_port, instance->n_io_port,
instance->base, instance->irq,
instance->can_queue, instance->cmd_per_lun,
instance->sg_tablesize, instance->this_id,
hostdata->flags & FLAG_TAGGED_QUEUING ? "TAGGED_QUEUING " : "",
+ hostdata->flags & FLAG_TOSHIBA_DELAY ? "TOSHIBA_DELAY " : "",
#ifdef DIFFERENTIAL
"DIFFERENTIAL "
#endif
@@ -860,6 +861,7 @@
static int NCR5380_maybe_reset_bus(struct Scsi_Host *instance)
{
+ struct NCR5380_hostdata *hostdata = shost_priv(instance);
int pass;
for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) {
@@ -878,6 +880,14 @@
case 4:
shost_printk(KERN_ERR, instance, "bus busy, attempting reset\n");
do_reset(instance);
+ /* Wait after a reset; the SCSI standard calls for
+ * 250ms, we wait 500ms to be on the safe side.
+ * But some Toshiba CD-ROMs need ten times that.
+ */
+ if (hostdata->flags & FLAG_TOSHIBA_DELAY)
+ msleep(2500);
+ else
+ msleep(500);
break;
case 6:
shost_printk(KERN_ERR, instance, "bus locked solid\n");
@@ -1493,12 +1503,10 @@
* a minimum so we'll udelay ceil(1.2)
*/
-#ifdef CONFIG_ATARI_SCSI_TOSHIBA_DELAY
- /* ++roman: But some targets (see above :-) seem to need a bit more... */
- udelay(15);
-#else
- udelay(2);
-#endif
+ if (hostdata->flags & FLAG_TOSHIBA_DELAY)
+ udelay(15);
+ else
+ udelay(2);
if (hostdata->connected) {
NCR5380_write(MODE_REG, MR_BASE);