iio: add LM3533 ambient-light-sensor driver
Add sub-driver for the ambient-light-sensor interface on National
Semiconductor / TI LM3533 lighting power chips.
The sensor interface can be used to control the LEDs and backlights of
the chip through defining five light zones and three sets of
corresponding output-current values.
The driver provides raw and mean adc readings along with the current
light zone through sysfs. A threshold event can be generated on zone
changes. The ALS-control output values can be set per zone for the three
current output channels.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als b/Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als
new file mode 100644
index 0000000..694a52c
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als
@@ -0,0 +1,62 @@
+What: /sys/.../events/in_illuminance0_thresh_either_en
+Date: April 2012
+KernelVersion: 3.5
+Contact: Johan Hovold <jhovold@gmail.com>
+Description:
+ Event generated when channel passes one of the four thresholds
+ in each direction (rising|falling) and a zone change occurs.
+ The corresponding light zone can be read from
+ in_illuminance0_zone.
+
+What: /sys/.../events/in_illuminance0_threshY_hysteresis
+Date: May 2012
+KernelVersion: 3.5
+Contact: Johan Hovold <jhovold@gmail.com>
+Description:
+ Get the hysteresis for thresholds Y, that is,
+
+ threshY_hysteresis = threshY_raising - threshY_falling
+
+What: /sys/.../events/illuminance_threshY_falling_value
+What: /sys/.../events/illuminance_threshY_raising_value
+Date: April 2012
+KernelVersion: 3.5
+Contact: Johan Hovold <jhovold@gmail.com>
+Description:
+ Specifies the value of threshold that the device is comparing
+ against for the events enabled by
+ in_illuminance0_thresh_either_en (0..255), where Y in 0..3.
+
+ Note that threshY_falling must be less than or equal to
+ threshY_raising.
+
+ These thresholds correspond to the eight zone-boundary
+ registers (boundaryY_{low,high}) and defines the five light
+ zones.
+
+What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_zone
+Date: April 2012
+KernelVersion: 3.5
+Contact: Johan Hovold <jhovold@gmail.com>
+Description:
+ Get the current light zone (0..4) as defined by the
+ in_illuminance0_threshY_{falling,rising} thresholds.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_currentY_raw
+Date: May 2012
+KernelVersion: 3.5
+Contact: Johan Hovold <jhovold@gmail.com>
+Description:
+ Get output current for channel Y (0..255), that is,
+ out_currentY_currentZ_raw, where Z is the current zone.
+
+What: /sys/bus/iio/devices/iio:deviceX/out_currentY_currentZ_raw
+Date: May 2012
+KernelVersion: 3.5
+Contact: Johan Hovold <jhovold@gmail.com>
+Description:
+ Set the output current for channel out_currentY when in zone
+ Z (0..255), where Y in 0..2 and Z in 0..4.
+
+ These values correspond to the ALS-mapper target registers for
+ ALS-mapper Y + 1.