[ARM] 4124/1: Rename mach-at91rm9200 and arch-at91rm9200 directories
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/board-csb637.c b/arch/arm/mach-at91/board-csb637.c
new file mode 100644
index 0000000..7746094
--- /dev/null
+++ b/arch/arm/mach-at91/board-csb637.c
@@ -0,0 +1,109 @@
+/*
+ * linux/arch/arm/mach-at91/board-csb637.c
+ *
+ * Copyright (C) 2005 SAN People
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+/*
+ * Serial port configuration.
+ * 0 .. 3 = USART0 .. USART3
+ * 4 = DBGU
+ */
+static struct at91_uart_config __initdata csb637_uart_config = {
+ .console_tty = 0, /* ttyS0 */
+ .nr_tty = 2,
+ .tty_map = { 4, 1, -1, -1, -1 } /* ttyS0, ..., ttyS4 */
+};
+
+static void __init csb637_map_io(void)
+{
+ /* Initialize processor: 3.6864 MHz crystal */
+ at91rm9200_initialize(3686400, AT91RM9200_BGA);
+
+ /* Setup the LEDs */
+ at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
+
+ /* Setup the serial ports and console */
+ at91_init_serial(&csb637_uart_config);
+}
+
+static void __init csb637_init_irq(void)
+{
+ at91rm9200_init_interrupts(NULL);
+}
+
+static struct at91_eth_data __initdata csb637_eth_data = {
+ .phy_irq_pin = AT91_PIN_PC0,
+ .is_rmii = 0,
+};
+
+static struct at91_usbh_data __initdata csb637_usbh_data = {
+ .ports = 2,
+};
+
+static struct at91_udc_data __initdata csb637_udc_data = {
+ .vbus_pin = AT91_PIN_PB28,
+ .pullup_pin = AT91_PIN_PB1,
+};
+
+static void __init csb637_board_init(void)
+{
+ /* Serial */
+ at91_add_device_serial();
+ /* Ethernet */
+ at91_add_device_eth(&csb637_eth_data);
+ /* USB Host */
+ at91_add_device_usbh(&csb637_usbh_data);
+ /* USB Device */
+ at91_add_device_udc(&csb637_udc_data);
+ /* I2C */
+ at91_add_device_i2c();
+ /* SPI */
+ at91_add_device_spi(NULL, 0);
+}
+
+MACHINE_START(CSB637, "Cogent CSB637")
+ /* Maintainer: Bill Gatliff */
+ .phys_io = AT91_BASE_SYS,
+ .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+ .boot_params = AT91_SDRAM_BASE + 0x100,
+ .timer = &at91rm9200_timer,
+ .map_io = csb637_map_io,
+ .init_irq = csb637_init_irq,
+ .init_machine = csb637_board_init,
+MACHINE_END