efikamx: add usb h1 support
Now that usb has been fixed, we can enable usb h1 on efikamx
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
diff --git a/arch/arm/mach-mx5/Kconfig b/arch/arm/mach-mx5/Kconfig
index aa20a38..1405464 100644
--- a/arch/arm/mach-mx5/Kconfig
+++ b/arch/arm/mach-mx5/Kconfig
@@ -119,6 +119,7 @@
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
select IMX_HAVE_PLATFORM_SPI_IMX
+ select MXC_ULPI if USB_ULPI
config MACH_MX51_EFIKAMX
bool "Support MX51 Genesi Efika MX nettop"
diff --git a/arch/arm/mach-mx5/board-mx51_efikamx.c b/arch/arm/mach-mx5/board-mx51_efikamx.c
index 272de6e..8f17336 100644
--- a/arch/arm/mach-mx5/board-mx51_efikamx.c
+++ b/arch/arm/mach-mx5/board-mx51_efikamx.c
@@ -211,6 +211,20 @@
gpio_request(EFIKAMX_RESET, "reset");
gpio_direction_output(EFIKAMX_RESET, 1);
}
+
+ /*
+ * enable wifi by default only on mx
+ * sb and mx have same wlan pin but the value to enable it are
+ * different :/
+ */
+ gpio_request(EFIKA_WLAN_EN, "wlan_en");
+ gpio_direction_output(EFIKA_WLAN_EN, 0);
+ msleep(10);
+
+ gpio_request(EFIKA_WLAN_RESET, "wlan_rst");
+ gpio_direction_output(EFIKA_WLAN_RESET, 0);
+ msleep(10);
+ gpio_set_value(EFIKA_WLAN_RESET, 1);
}
static void __init mx51_efikamx_timer_init(void)
diff --git a/arch/arm/mach-mx5/efika.h b/arch/arm/mach-mx5/efika.h
index c828043..014aa98 100644
--- a/arch/arm/mach-mx5/efika.h
+++ b/arch/arm/mach-mx5/efika.h
@@ -1,6 +1,10 @@
#ifndef _EFIKA_H
#define _EFIKA_H
+#define EFIKA_WLAN_EN IMX_GPIO_NR(2, 16)
+#define EFIKA_WLAN_RESET IMX_GPIO_NR(2, 10)
+#define EFIKA_USB_PHY_RESET IMX_GPIO_NR(2, 9)
+
void __init efika_board_common_init(void);
#endif
diff --git a/arch/arm/mach-mx5/mx51_efika.c b/arch/arm/mach-mx5/mx51_efika.c
index a249ca3..c08ec63 100644
--- a/arch/arm/mach-mx5/mx51_efika.c
+++ b/arch/arm/mach-mx5/mx51_efika.c
@@ -30,6 +30,10 @@
#include <mach/i2c.h>
#include <mach/mxc_ehci.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/ulpi.h>
+#include <mach/ulpi.h>
+
#include <asm/irq.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
@@ -40,7 +44,12 @@
#include "devices.h"
#include "efika.h"
-#define MX51_USB_PLL_DIV_24_MHZ 0x01
+#define MX51_USB_CTRL_1_OFFSET 0x10
+#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
+#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
+
+#define EFIKAMX_USB_HUB_RESET IMX_GPIO_NR(1, 5)
+#define EFIKAMX_USBH1_STP IMX_GPIO_NR(1, 27)
#define EFIKAMX_SPI_CS0 IMX_GPIO_NR(4, 24)
#define EFIKAMX_SPI_CS1 IMX_GPIO_NR(4, 25)
@@ -81,6 +90,29 @@
MX51_PAD_CSPI1_SS1__GPIO4_25,
MX51_PAD_CSPI1_RDY__ECSPI1_RDY,
MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
+
+ /* USB HOST1 */
+ MX51_PAD_USBH1_CLK__USBH1_CLK,
+ MX51_PAD_USBH1_DIR__USBH1_DIR,
+ MX51_PAD_USBH1_NXT__USBH1_NXT,
+ MX51_PAD_USBH1_DATA0__USBH1_DATA0,
+ MX51_PAD_USBH1_DATA1__USBH1_DATA1,
+ MX51_PAD_USBH1_DATA2__USBH1_DATA2,
+ MX51_PAD_USBH1_DATA3__USBH1_DATA3,
+ MX51_PAD_USBH1_DATA4__USBH1_DATA4,
+ MX51_PAD_USBH1_DATA5__USBH1_DATA5,
+ MX51_PAD_USBH1_DATA6__USBH1_DATA6,
+ MX51_PAD_USBH1_DATA7__USBH1_DATA7,
+
+ /* USB HUB RESET */
+ MX51_PAD_GPIO1_5__GPIO1_5,
+
+ /* WLAN */
+ MX51_PAD_EIM_A22__GPIO2_16,
+ MX51_PAD_EIM_A16__GPIO2_10,
+
+ /* USB PHY RESET */
+ MX51_PAD_EIM_D27__GPIO2_9,
};
/* Serial ports */
@@ -105,13 +137,13 @@
/* Set the PHY clock to 19.2MHz */
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
- v |= MX51_USB_PLL_DIV_24_MHZ;
+ v |= MX51_USB_PLL_DIV_19_2_MHZ;
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
iounmap(usb_base);
mdelay(10);
- return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
+ return mx51_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
}
static struct mxc_usbh_platform_data dr_utmi_config = {
@@ -119,6 +151,73 @@
.portsc = MXC_EHCI_UTMI_16BIT,
};
+static int initialize_usbh1_port(struct platform_device *pdev)
+{
+ iomux_v3_cfg_t usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
+ iomux_v3_cfg_t usbh1gpio = MX51_PAD_USBH1_STP__GPIO1_27;
+ u32 v;
+ void __iomem *usb_base;
+ void __iomem *socregs_base;
+
+ mxc_iomux_v3_setup_pad(usbh1gpio);
+ gpio_request(EFIKAMX_USBH1_STP, "usbh1_stp");
+ gpio_direction_output(EFIKAMX_USBH1_STP, 0);
+ msleep(1);
+ gpio_set_value(EFIKAMX_USBH1_STP, 1);
+ msleep(1);
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+ socregs_base = (void __iomem *)(usb_base + MX5_USBOTHER_REGS_OFFSET);
+
+ /* The clock for the USBH1 ULPI port will come externally */
+ /* from the PHY. */
+ v = __raw_readl(socregs_base + MX51_USB_CTRL_1_OFFSET);
+ __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
+ socregs_base + MX51_USB_CTRL_1_OFFSET);
+
+ iounmap(usb_base);
+
+ gpio_free(EFIKAMX_USBH1_STP);
+ mxc_iomux_v3_setup_pad(usbh1stp);
+
+ mdelay(10);
+
+ return mx51_initialize_usb_hw(0, MXC_EHCI_ITC_NO_THRESHOLD);
+}
+
+static struct mxc_usbh_platform_data usbh1_config = {
+ .init = initialize_usbh1_port,
+ .portsc = MXC_EHCI_MODE_ULPI,
+};
+
+static void mx51_efika_hubreset(void)
+{
+ gpio_request(EFIKAMX_USB_HUB_RESET, "usb_hub_rst");
+ gpio_direction_output(EFIKAMX_USB_HUB_RESET, 1);
+ msleep(1);
+ gpio_set_value(EFIKAMX_USB_HUB_RESET, 0);
+ msleep(1);
+ gpio_set_value(EFIKAMX_USB_HUB_RESET, 1);
+}
+
+static void __init mx51_efika_usb(void)
+{
+ mx51_efika_hubreset();
+
+ /* pulling it low, means no USB at all... */
+ gpio_request(EFIKA_USB_PHY_RESET, "usb_phy_reset");
+ gpio_direction_output(EFIKA_USB_PHY_RESET, 0);
+ msleep(1);
+ gpio_set_value(EFIKA_USB_PHY_RESET, 1);
+
+ usbh1_config.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+ ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT |
+ ULPI_OTG_EXTVBUSIND);
+
+ mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
+ mxc_register_device(&mxc_usbh1_device, &usbh1_config);
+}
+
static struct mtd_partition mx51_efika_spi_nor_partitions[] = {
{
.name = "u-boot",
@@ -164,8 +263,8 @@
{
mxc_iomux_v3_setup_multiple_pads(mx51efika_pads,
ARRAY_SIZE(mx51efika_pads));
- mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
imx51_add_imx_uart(0, &uart_pdata);
+ mx51_efika_usb();
imx51_add_sdhci_esdhc_imx(0, NULL);
spi_register_board_info(mx51_efika_spi_board_info,