tree-wide: fix typos "ammount" -> "amount"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
diff --git a/drivers/char/serial167.c b/drivers/char/serial167.c
index 452370a..aee3c0d 100644
--- a/drivers/char/serial167.c
+++ b/drivers/char/serial167.c
@@ -1990,7 +1990,7 @@
/*
* Attempt to set up all channels to something reasonable, and
* bang out a INIT_CHAN command. We should then be able to limit
- * the ammount of fiddling we have to do in normal running.
+ * the amount of fiddling we have to do in normal running.
*/
for (ch = 3; ch >= 0; ch--) {
diff --git a/drivers/isdn/sc/hardware.h b/drivers/isdn/sc/hardware.h
index 9e6d530..6273248 100644
--- a/drivers/isdn/sc/hardware.h
+++ b/drivers/isdn/sc/hardware.h
@@ -87,7 +87,7 @@
#define BRI_CHANNELS 2 /* Number of B channels */
#define BRI_BASEPG_VAL 0x98
#define BRI_MAGIC 0x60000 /* Magic Number */
-#define BRI_MEMSIZE 0x10000 /* Ammount of RAM (64K) */
+#define BRI_MEMSIZE 0x10000 /* Amount of RAM (64K) */
#define BRI_PARTNO "72-029"
#define BRI_FEATURES ISDN_FEATURE_L2_HDLC | ISDN_FEATURE_L3_TRANS;
/*
diff --git a/drivers/message/i2o/iop.c b/drivers/message/i2o/iop.c
index e5ab621..ef5ce26 100644
--- a/drivers/message/i2o/iop.c
+++ b/drivers/message/i2o/iop.c
@@ -539,7 +539,7 @@
* which is indeterminate. We need to wait until the IOP has
* rebooted before we can let the system talk to it. We read
* the inbound Free_List until a message is available. If we
- * can't read one in the given ammount of time, we assume the
+ * can't read one in the given amount of time, we assume the
* IOP could not reboot properly.
*/
osm_debug("%s: Reset in progress, waiting for reboot...\n",
diff --git a/drivers/net/ks8851.c b/drivers/net/ks8851.c
index 6d3ac65..cfebe0e 100644
--- a/drivers/net/ks8851.c
+++ b/drivers/net/ks8851.c
@@ -407,7 +407,7 @@
* @buff: The buffer address
* @len: The length of the data to read
*
- * Issue an RXQ FIFO read command and read the @len ammount of data from
+ * Issue an RXQ FIFO read command and read the @len amount of data from
* the FIFO into the buffer specified by @buff.
*/
static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len)
diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c
index e67e4fe..215621c 100644
--- a/drivers/platform/x86/thinkpad_acpi.c
+++ b/drivers/platform/x86/thinkpad_acpi.c
@@ -1667,7 +1667,7 @@
* Table of recommended minimum BIOS versions
*
* Reasons for listing:
- * 1. Stable BIOS, listed because the unknown ammount of
+ * 1. Stable BIOS, listed because the unknown amount of
* bugs and bad ACPI behaviour on older versions
*
* 2. BIOS or EC fw with known bugs that trigger on Linux
@@ -7070,7 +7070,7 @@
*
* Fan speed changes of any sort (including those caused by the
* disengaged mode) are usually done slowly by the firmware as the
- * maximum ammount of fan duty cycle change per second seems to be
+ * maximum amount of fan duty cycle change per second seems to be
* limited.
*
* Reading is not available if GFAN exists.
diff --git a/drivers/scsi/libfc/fc_fcp.c b/drivers/scsi/libfc/fc_fcp.c
index 881d5df..96ee599 100644
--- a/drivers/scsi/libfc/fc_fcp.c
+++ b/drivers/scsi/libfc/fc_fcp.c
@@ -522,7 +522,7 @@
*
* Called after receiving a Transfer Ready data descriptor.
* If the LLD is capable of sequence offload then send down the
- * seq_blen ammount of data in single frame, otherwise send
+ * seq_blen amount of data in single frame, otherwise send
* multiple frames of the maximum frame payload supported by
* the target port.
*/
diff --git a/drivers/serial/samsung.c b/drivers/serial/samsung.c
index 52e3df1..03c010a 100644
--- a/drivers/serial/samsung.c
+++ b/drivers/serial/samsung.c
@@ -1271,7 +1271,7 @@
unsigned long ufstat, utrstat;
if (ufcon & S3C2410_UFCON_FIFOMODE) {
- /* fifo mode - check ammount of data in fifo registers... */
+ /* fifo mode - check amount of data in fifo registers... */
ufstat = rd_regl(port, S3C2410_UFSTAT);
return (ufstat & info->tx_fifofull) ? 0 : 1;
diff --git a/drivers/usb/serial/opticon.c b/drivers/usb/serial/opticon.c
index 4cdb975..96937f1 100644
--- a/drivers/usb/serial/opticon.c
+++ b/drivers/usb/serial/opticon.c
@@ -120,7 +120,7 @@
}
} else {
dev_dbg(&priv->udev->dev,
- "Improper ammount of data received from the device, "
+ "Improper amount of data received from the device, "
"%d bytes", urb->actual_length);
}
diff --git a/drivers/usb/serial/symbolserial.c b/drivers/usb/serial/symbolserial.c
index b282c0f..aebfcf6 100644
--- a/drivers/usb/serial/symbolserial.c
+++ b/drivers/usb/serial/symbolserial.c
@@ -100,7 +100,7 @@
}
} else {
dev_dbg(&priv->udev->dev,
- "Improper ammount of data received from the device, "
+ "Improper amount of data received from the device, "
"%d bytes", urb->actual_length);
}