| # Copyright 2007 Simtec Electronics |
| # |
| # Licensed under GPLv2 |
| |
| config CPU_S3C2410 |
| bool |
| depends on ARCH_S3C2410 |
| select CPU_ARM920T |
| select S3C_GPIO_PULL_UP |
| select S3C2410_CLOCK |
| select S3C2410_GPIO |
| select CPU_LLSERIAL_S3C2410 |
| select S3C2410_PM if PM |
| select S3C2410_CPUFREQ if CPU_FREQ_S3C24XX |
| help |
| Support for S3C2410 and S3C2410A family from the S3C24XX line |
| of Samsung Mobile CPUs. |
| |
| config CPU_S3C2410_DMA |
| bool |
| depends on S3C2410_DMA && (CPU_S3C2410 || CPU_S3C2442) |
| default y if CPU_S3C2410 || CPU_S3C2442 |
| help |
| DMA device selection for S3C2410 and compatible CPUs |
| |
| config S3C2410_PM |
| bool |
| help |
| Power Management code common to S3C2410 and better |
| |
| config S3C2410_GPIO |
| bool |
| help |
| GPIO code for S3C2410 and similar processors |
| |
| config SIMTEC_NOR |
| bool |
| help |
| Internal node to specify machine has simtec NOR mapping |
| |
| config MACH_BAST_IDE |
| bool |
| select HAVE_PATA_PLATFORM |
| help |
| Internal node for machines with an BAST style IDE |
| interface |
| |
| # cpu frequency scaling support |
| |
| config S3C2410_CPUFREQ |
| bool |
| depends on CPU_FREQ_S3C24XX && CPU_S3C2410 |
| select S3C2410_CPUFREQ_UTILS |
| help |
| CPU Frequency scaling support for S3C2410 |
| |
| config S3C2410_PLLTABLE |
| bool |
| depends on S3C2410_CPUFREQ && CPU_FREQ_S3C24XX_PLL |
| default y |
| help |
| Select the PLL table for the S3C2410 |
| |
| menu "S3C2410 Machines" |
| |
| config ARCH_SMDK2410 |
| bool "SMDK2410/A9M2410" |
| select CPU_S3C2410 |
| select MACH_SMDK |
| help |
| Say Y here if you are using the SMDK2410 or the derived module A9M2410 |
| <http://www.fsforth.de> |
| |
| config ARCH_H1940 |
| bool "IPAQ H1940" |
| select CPU_S3C2410 |
| select PM_H1940 if PM |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_NAND |
| select S3C2410_SETUP_TS |
| help |
| Say Y here if you are using the HP IPAQ H1940 |
| |
| config H1940BT |
| tristate "Control the state of H1940 bluetooth chip" |
| depends on ARCH_H1940 |
| select RFKILL |
| help |
| This is a simple driver that is able to control |
| the state of built in bluetooth chip on h1940. |
| |
| config PM_H1940 |
| bool |
| help |
| Internal node for H1940 and related PM |
| |
| config MACH_N30 |
| bool "Acer N30 family" |
| select CPU_S3C2410 |
| select MACH_N35 |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_NAND |
| help |
| Say Y here if you want suppt for the Acer N30, Acer N35, |
| Navman PiN570, Yakumo AlphaX or Airis NC05 PDAs. |
| |
| config MACH_N35 |
| bool |
| help |
| Internal node in order to enable support for Acer N35 if Acer N30 is |
| selected. |
| |
| config ARCH_BAST |
| bool "Simtec Electronics BAST (EB2410ITX)" |
| select CPU_S3C2410 |
| select S3C2410_IOTIMING if S3C2410_CPUFREQ |
| select PM_SIMTEC if PM |
| select SIMTEC_NOR |
| select MACH_BAST_IDE |
| select S3C24XX_DCLK |
| select ISA |
| select S3C_DEV_HWMON |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_NAND |
| help |
| Say Y here if you are using the Simtec Electronics EB2410ITX |
| development board (also known as BAST) |
| |
| config MACH_OTOM |
| bool "NexVision OTOM Board" |
| select CPU_S3C2410 |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_NAND |
| help |
| Say Y here if you are using the Nex Vision OTOM board |
| |
| config MACH_AML_M5900 |
| bool "AML M5900 Series" |
| select CPU_S3C2410 |
| select PM_SIMTEC if PM |
| select S3C_DEV_USB_HOST |
| help |
| Say Y here if you are using the American Microsystems M5900 Series |
| <http://www.amltd.com> |
| |
| config BAST_PC104_IRQ |
| bool "BAST PC104 IRQ support" |
| depends on ARCH_BAST |
| default y |
| help |
| Say Y here to enable the PC104 IRQ routing on the |
| Simtec BAST (EB2410ITX) |
| |
| config MACH_TCT_HAMMER |
| bool "TCT Hammer Board" |
| select CPU_S3C2410 |
| select S3C_DEV_USB_HOST |
| help |
| Say Y here if you are using the TinCanTools Hammer Board |
| <http://www.tincantools.com> |
| |
| config MACH_VR1000 |
| bool "Thorcom VR1000" |
| select PM_SIMTEC if PM |
| select S3C24XX_DCLK |
| select SIMTEC_NOR |
| select MACH_BAST_IDE |
| select CPU_S3C2410 |
| select S3C_DEV_USB_HOST |
| help |
| Say Y here if you are using the Thorcom VR1000 board. |
| |
| config MACH_QT2410 |
| bool "QT2410" |
| select CPU_S3C2410 |
| select S3C_DEV_USB_HOST |
| select S3C_DEV_NAND |
| help |
| Say Y here if you are using the Armzone QT2410 |
| |
| endmenu |